Construction of 2 MLD waste water Treatment Plant for WRD at Ottakulam Tank using the Advanced Nano Bio Ozolyte treatment system in Pudukkottai District.

Earth work excavating and depositing on bank with initial lead of 10m & initial lift of 2m in Sand, silt or other loose soil, wet sand or silt not under water, light black cotton soil, sandy loam and ordinary soil including excavated earth etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and filling in foundation, basement, etc with filling crushed stone sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Cement Concrete 1:3:6 (One Cement, Three crushed stone sand and Six broken stone jelly) using 40mm size hard broken stone jelly excluding cost of centering shuttering reinforcement grills and fabrication charges but including curing etc. complete and as directed by the departmental officers. - machine mix

Brick work in Cement Mortar using best quality Burnt Clay Brick of size 9” x 4 3/8” x 2 3/4” with class designation of 7.5 conforming to IS 1077-1992 for foundation and basement including Cost of Mortar Plasticizer curing, etc.,complete complying with standard specification and as directed by the departmental officers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally.other type of bond shall be done etc. complete and as directed by the departmental officers.

Foundation and Basement

Super Structure in Ground Floor

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, Sill slabs etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid with silver oak joists of size 10cm x 5cm & 7.5cm x 5cm as support runner , vertical stiffener, side support and Top Horizontal stiffener spaced at about 60cm to 90cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation and as directed by the departmental officers.

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall, etc. using mild steel sheets of size 1200cm x 60cm and 10 BG stiffened with welded mild steel angles of size 40mm x 40mm x 5 mm for boarding, laid with silver oak joists of size 10cm x 5cm & 7.5cm x 5cm as support runner, Top Horizontal stiffener spaced at about 60cm to 90cm centre to centre or at suitable intervals. MS Channel Section (ISMC 100) shall be provided as a vertical support @1.20m C/C and with Lateral support of Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) & steel pipes of 20mm dia @ required level/spacing etc. complete complying with standard specifcation and as directed by the departmental officers.

Supplying and erecting centering for plane surfaces such as RCC Floor/Roof Beam, Lintels, Cantilever Beams, Bed Blocks etc.. with necessary supports and strutting upto 3.60m height in all floors with all cross bracings using MS Sheets made of 10 gauge thick welded with MS angle of Size 25mm x 25mm x 3mm for boarding laid over Steel adjustable Span of Size 2m x 2m(expandable upto 3.60m) and Silver Oak Joists of Size 10 x 5 cm spaced at 50cm to 60cm c/c and supported by Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick) Spaced at not more than 50 to 60cm c/c , etc complete complying with standard specifications. Steel adjustable span and Steel Adjustable telescopic props shall be provided as directed by the departmental Officers.

Plain Cement Concrete 1:2:4 (one cement, two crushed stone sand and four hard broken stone jelly) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers - machine mix

Cement Concrete 1:1-1/2:3 (One Cement, One and a half crushed stone sand and Three hard broken stone jelly) using 20 mm gauge hard broken granite stone jelly for all RCC items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including Super Plasticiser, mixing charges for machine mix, laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc. shall be finished smooth with Cement Mortar 1:3 (One Cement and Three Sand) and kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers - machine mix

For Foundation and Basement

For Super Structure-Ground floor

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel reinforcement grills of all variety like HYSD/CTD/TMTand all grade like Fe 500, Fe550D, Fe 500 D etc., for all RCC works as per design given including cost of steel reinforcement and G.I. binding wire, wastage etc. complete complying with standard specification and as directed by the departmental officers.

Plastering with Cement Mortar 1:5 (One cement and Five Plastering sand), 12mm thick in all floors including mortar plasticizer at 200ml per 50Kg of cement used, curing etc. complete complying with standard specification and as directed by the departmental officers.

Plastering the surface of walls with Cement Mortar 1:3 (One cement and Three plastering sand), 12mm thick in all floors including mortar plasticizer at 200ml per 50Kg of cement used, curing etc., complete complying with standard specification and as directed by the departmental officers.

Manufacturing supplying and fixing of Fully Panelled steel door Single leaf of size 1.00m x 2.10m. with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames, stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter. 3nos. of Steel Parliament Hinges of Size 125mm x 150mm in case of single leaf and 6nos. of Steel Parliament Hinges of Size 125mm x 150mm in double leaves shutter to be provided. 6nos. of holdfasts 200 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 3 nos, one at the top, one at lock rail(Inner) and the other at the bottom are provided 1no. Aldrop is provided at lock rail section in the door 2 Nos of 200mm handle are to be provided. One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters. at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete complying with standard specification and as directed by the departmental officers.

Fabricating, Supplying and fixing in position of steel glazed window (Two Leaves ) with the following specifications. Outer frames of windows made of ‘Z’ section F7D of size 33 x 25 x 3mm at 1.419 kg/ m and mullion ‘J’ section (F4B) of size 46x25x3mm at 2.28kg/m and shutter section of made of F7D of 33x25x3mm at 1.419 kg/m as specified in IS 7452/1990. Each openable shutter should not exceed a width of 600mm to enable separate operations and easy maintenance. The panel of the shutters to be covered with 3mm thick pin headed glass and fixed with 15x12mm teakwood beading of superior quality and fixed with shutter frames.2 numbers of Steel Offset Pivot hinges of size 3” and one number of handle to be fixed to each shutter at an appropriate height in window. suitable opening is left for its easy operation. a stopper square rod for handle is provided in the mullion section at suitable place to catch the window handle. each window shutter having an adjustable stay made out of 18 x 5mm at 0.70 kg/ m MS flat of length 320mm with three adjustable position. A matching peg is provided in the outer frame of the window at suitable place. 4 Nos. of hold fasts of 200mm length spliced at the ends are welded to the outer frame of the window. An MS square bar of 12mm size is welded to the inner face of the window at an equal interval interval not exceeding 100mm edge between them. All members are painted with one coat of anti-corrosive red oxide primer as directed by the departmental officers. All sections should be in confirmed with IS 7452/1990.The cost includes cost of all materials, labour charges and other incidental charges, etc., complete complying with standard specification and as directed by the departmental officers.

Providing granolithic floor finish 25mm thickness with plain cement concrete 1:2:4 (One Cement, Two Crushed Stone Sand and Four aggregate) using 6 to12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trowel, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers)

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no crushed stone sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of PRESSED TILES of size 230mm x 230mm x 16 mm of approved quality laid in cement mortar 1:3 (One cement and three sand) 12mm thick mixed with water proofing compound conforming to I.S. at 2% by weight of cement used and the top pointed with same mortar mixed with redoxide to the full depth of tiles, complete complying with standard specification. (The rate is inclusive of redoxide and water proofing compound ) and as directed by the departmental officers.

Providing & fixing PVC RAIN WATER DOWNFALL PIPE 110mm dia PVC Pipe [4 Kg/SqCm] with necessary T.W.Clamps Plugs, Shoes,Bemds, other clamps, screws nails etc.,complete complying with standard specification. The rate is inclusive of cost of removable iron gratings of appropriate size. The size of Teak Wood plugs used is 150X25mm in front & 200x75mm in rear (wall side) with a depth of 110mm. The pipe is to be fixed by means of "U" clamps at the centre of pipes to be fixed.

Supplying and fixing GI pipe hand rails for handicapped persons using 50mm dia GI pipe double handrail at a height of 800mm and 900mm from floor level with 25mm thick MS square rods as balusters embedded in the concrete and welded with pipe at 60cm centre to centre as shown in CA Job No. 9123 / 1 including cutting, welding, bending and fixing charges and applying one coat of red oxide primer for MS members as directed by the departmental officers

White washing two coats with freshly burnt white shell lime in all floors including cost of lime, blue powder fevicol type gum, brushes, scaffolding charges, etc., complete complying with standard specification and as directed.

Colour washing two coats in all floors using best freshly burnt white shell lime and best quality of approved variety of colouring pigment including cost of lime, colouring pigments, fevicol type gum, brushes, scaffolding charges etc., complete complying with standard specification. Mineral colouring pigments not affected by lime should only be used (stainers and colour solutions should not be used.)

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification and as directed by the departmental officers. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Supply and erection of PVC tank ISI brand of required capacity (300, 500 and 1000 liters) for storage of Anolyte liquid with all accessories to from pump to deleivary point and from anolyte machine to tanks outside with necessary control valves and taps as per the departmental engineer direction

Supplying and fixing of EBB Block (Eco-Bio Block or equivalent ) OCT type and assembling as EBB reactor with necessary 2" dia PVC pipes and unions inserting 16 mm RTS steel rods inside PVC pipe in the aeration zone including transportation and labour charges.

Supplying and spraying of microbial ( Bio clean or equivalent brand) powder of having both anaerobic and aerobic stains and each gram shall contain billions of microbes which are degradable and able to bring down the BOD level to 70% less than the available including transportation charges.

Supplying and spraying of Nano Nualgi or equivalent Nano brand bio remediation powder or liquid having all micronutrients biologically available form to grow diatom and then feed to planktons and shall able to increase oxygen level in the waste water including transportation charges.

Supplying and erection of high efficiency oxygen transfer Submergible aerators (EOLO2 or Equivalent) of 2.0 HP capacity with 90 degree adjustable angle for three phase operation with inter cooled system, compact and light weight construction and one meter adjustable operating depth, corrosion resistant of 1.2 Kw with 3200 RPM and air capacity not less than 15000 liters/ minute with total 18 to 20 kg weight and including all accessories such as water proof electrical 2,5 sq mm three core cable with ISI make, standard 15 amp switches and L&T auto starter 15 amp to connect from panel board of Pump room to plant complete etc and erection and commission charges.

Supplying and erection of Submersible 5.00 HP ISI non clog electrical motor cutter and crushing motor to mix in the collection well of three phase 415v, 50HZ staturary parts like motor body, oil chamber, volute etc are of graded C.I castings shaft shall be SS heavy duty anti friction ball bearings shall be fitted . Impeller shall be CI/SS multicore PVC round cable with double PVC sheathing shall be mounted as standard accsessary.All assemble parts are made water tight using suitable O rings /gaskets.Rotor and impeller are dyanamically balanced for vibration and free rotation and solid handling size 125 mm with 1450 -1800 RPM including transportation charges and all accessories such as 2.5 sq mm three core cables with ISI make 15 amp switches and L& T automatic 15 amp starter and erection charges.

Supplying and erection of imported AQUASOL( Anolyte) liquid manufacturing machine- 60 model with Input power 230v +/-10% frequency 50 +/- 0.5. The electrochemical activation of water involves the exposure of water and natural salts to a substantial difference in electrical potential. Under, electrolysis process, the water leading to the breakdown its constituent elements – If table salt, is used as a brine solution, the dominant electrolysis end product is various forms of powerfull chlorine compounds in 0.01 - 0.06% concentration and also sodium hydroxide which too naturally synthazised from the water is useful to precipitating heavy metals. Its a metastable liquid and more stable than any other chlorine based agents in the world. The electrochemical cell is divided by a patented diaphragm. The specially designed membrane, which separates the two chambers, allows the ions to pass unimpeded. The net result is an enrichment of chlorine ions in the anode chamber and sodium and hydroxide ions in the cathode chamber. ORP levels can last for long periods of time depending on organic load. Tests show that not only is AQUASOL(Anolyte) a sanitizer and a disinfectant, but it is also sporicidal. Sporicidal tests also demonstrate that AQUASOL(Anolyte) treatment eliminates bacterial spores and biofilm. Even at residual levels over 12 ppm in treated water, leaves no or minimal odor or chlorine. The system including all accessories such as 2.5 sq mm cables 2.5 sq mm three core cables and ISI make 15 amp switches and L & T automatic 15 amp starter and including labour for - Production capacity 60 lit/ hr of active solution( mixed oxidants called Anolyte or Aquasol) - Power consumption 400 W/h - Brine solution consumption 1.5 to 2 g/lit of active solution - Ingredients : Hypochlorous, hypochlorite ion, chlorine,chlorine dioxide, hydrogen peroxide, ozone, Atomir - Strength of active solution 100-600ppm - Redox potential 700-1200mv - PH 6-8 - Power circuit breaker - Safety auto shut off - Digital display for parameters - Size 380x280x260 mm - Weight 12.5 kg - Pressure pump 1/4-1/2 HP - Sedimentation Filter - Concentration testing kit etc.

Supplying, erection, testing and commissioning of 100 A capacity cubical panel board to install all 12 switches and starter made up of 16swg CRCA Ms sheet. The panel consists of 14 nos 1’’/1/8” copper flat for three phases and neutral buses and earth bus for al round the panel and inter connection between incoming switch to bushes 16 nos and eight swg rigid copper rod for inter connection between outgoing all switches to bushes and double earth connection for all I/C and O/G switches. The hylam sheet separation for buses to switches and also danger board. The mounted on smc bush insulator and using sleeve by red yellow blue and black colors. The panel mounted on base channel for the bottom of channel ( the switches are L &T and Siemens make only)etc as directed by departmental direction.

Manufacturing, Supply and erection of Standard Bar screen of manual operated typical size between 10 mm (or 3/8 inch) to 50 mm (or 2 inches) thick, by about 50 mm (2 inches) deep with 6mm thick of and connected with 65mm x65 mm S.S square tube with L angle of 75 mmx 75 mmx6mm for guide channels to insert the bar screen of the channel size of 1.20 mx 1.50 m as per the departmental officer direction.

Manufacturing, Supply and erection of manual operated Standard fine screen mesh of 0.5” to 1” (12mm to 25 mm) square size with SS materials all round connected with 65mm x65 mm S.S square tube with L angle of 75 mm x 75 mmx6mm for guide channels to insert the fine screen with suitable inclination and to the channel size of 1.20mx 1.50 m as per the departmental officer direction.

Supply and erection of 6" dia UPVC pipe for smooth transfer of water from one tank to other tanks through gravity etc.,

GST at 18%

Please Enable Macros to View BoQ information