SPL REPAIR TO BLDG NO T200 AND T201 OF 12 I R AND O FLT PROVN OF BATHING FACILITY AT 165 MH CONCRETE SHARP PIT FOR BIO MEDICAL WASTE NEAR BLDG NO T19 AT MH RCC JAFRI WALL FROM MAIN GATE TO VIP ENTRY OF HELIPAD OF 12 I R AND O FLT AND HARD STANDING WI

Amount

B/R Portion Taking down Chowkhat or frames not exceeding 1.5 Sqm each with shutters(Without taking off shutters from the frames.

All as per item 2 above but exceeding 1.5 Sqm but not exceeding 4 Sqm each `

S&F size of frame 125 x 60mm Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified,

M&L for 35mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

M/L 35mm thick 2nd class hard wood Glazed and skelton shutter, open rebated and prepared to receive glass, gauge etc. devided into squares with plain chamfered or rounded, mitred and rebated sash bars edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.24(a) complete all as specified.

S&F for anodised aluminium window powder coated and ventilator shutters, fixed type without sash bar, aluminium section of size 40 x 18 x 1.29mm thick including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified.

S&F for anodised aluminium powder coated ventilator shutter fixed type wihtout sash bar, aluminium section of size 40x18x1.29mm thick including necessary joining cleats glazing clips ruber packing, anodised aluminium snap beading screws etc complete all as specified and directed.

S & F chimney bars (straight or camber); bearing bars; tongues or water bars for window frames; window guard bars, plain, let in and fixed independently in wooden frames, L or T section supports for shelves etc., and similar articles conforming to Fe 410-0 or Fe 310-0, complete all as specified and as directed by the Engineer-in-Charge

M&L for sheet glass 3mm thick ordinary quality, pin headed type and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each pane.

S&F mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 18mm, fixed with tinned tacks or galvanized wire staples.

S & F 100 size stainless steel butt hinges complete all as specified and directed

S & F 75 size stainless steel butt hinges complete all as specified and directed

Supply & Fixing 150 mm Aluminium handles, cast type, anodised

Supply & Fixing 100 mm Aluminium handles, cast type, anodised

S & F 150 mm Aluminium, anodised, barrel tower bolts of extruded section and fixed

S & F 200 mm Aluminium, anodised, barrel tower bolts of extruded section and fixed

S & F 300 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast-aluminium alloy and fixed

S&F mild steel 300 mm, ordinary rat tail rod pattern springs including roller and roller plate complete

Taking down cement plaster on brick walls including raking out joints hacking for key, scrubbing down with water etc

M&L for rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished fair and even without using extra cement.

M&L for rendering 15mm thick in CM 1:4 other than fair faces of brick work or concrete surfaces finished even and smooth without using extra cement.

M & L rendering 5 mm thick in cement mortar 1:3 on fair faces of brick or concrete work even and smooth without using extra cement in ceiling.

M&L for preparation of new plastered or un plastered surface of walls including cornices, pilasters etc and applying two coats of cement base paint complete all as specified and directed.

M&L for applying two coats of oil bound distemper on new plastered inculding 2mm thick putty surfaces of walls including preparation of surface complete all as specified and directed.

M&L for Preparation of plasterded or un plastered new surfaces of ceiling and applying two coat of white wash complete all as specified and directed.

M&L for preparation of new surfaces of steel and iron work of any description over 10 cm width or girth not otherwise described and applying two coat of synthetic enamel paint over a coat of redoxide on new surfaces in any tint complete all as specified.

All as per item here in before but applying two coats of synthetic enamel paint over a coat of pink wood primer on new surfaces

Demolition, Cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed by the Engineer-in-Charge.

M & L for cement concrete 1:3:6 type C-2, 75 mm thick using 40mm graded stone aggregates as in plinth protection finished fair and even.

M/L 100mm thick PCC (1:3:6) type C2 using 40mm graded stone aggregate as in floor.

M & L for screed bed or bedding layer of mortar 20mm thick in CM 1:6 for laying floor finishes

M & L for chequered cement concrete tiles of Size 300 x 300 mm x 25mm thick any description jointed and pointed in neat cement slurry in floors with grey cement and pigment

M & L for 15 mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M & L for coloured non skid ceramic tiles 7 to 8 mm thick (square/rectangular) in section exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

Same as above but on vertical surfaces such as skirting , dado risers to steps over and including 10 mm thick bedding layer in CM 1:4 , set and jointed in neat cement slurry and pointed in white or coloured cement to match all as directed.

M&L for coloured Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick CM (1:4) backing coat.

M&L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15mm thick CM (1:4) screed bed.

S & F,Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F Factory made solid panel pvc door shutter 30 mm thick (style) con-sisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be cov-ered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement suppling & fixing at site as per specification and drawing complete all as specified and directed.

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar

M& L150mm dia DWC Pipe, pressure rating SN8 laid in trenches complete all as specified and directed.

M& L Concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; in complete all as specified and directed.

M&L cement concrete type C2 1:3:6 (40 mm graded agg) as in surface channels and drains

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement incl firms moulds

Demolition of cement concrete in reinforced of any description and in any position not otherwise specifically provided, complete all as specified & directed.

M&L TMT bars, 6 to 8mm, cut to length, bent to shape required including cranking,bending spirally for hooping for column, hooking ends and binding with and incl MS wire(annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for precast cement concrete type B1 1:2:4 (Using 20 mm graded stone aggregate) as in cover slabs, manhole cover, chamber cover and drainge cover set in cement mortar 1:6 including necessary formwok complete all as specified and directed.

Taking up or down steel tubing and connections including cleaning for refixing with all fittings for 15 mm bore GI tubing.

Taking up or down steel tubing and connections including cleaning for refixing with all fittings for 20 mm bore GI tubing.

S&F tubes medium grade, galvanised wih all fittings and fixed complete to walls and ceiling or laid on floors etc, 15 mm bore.

S&F tubes medium grade, galvanised wih all fittings and fixed complete to walls and ceiling or laid on floors etc, 20 mm bore.

Supply and fixed in repair vitreous china wash hand basin including brackets, white size 550 x 400 mm incl cutting cutting for and pinning in ends of brackets. Including Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other and fixed

S&F in repairs vitreous china water closet Padestal pattern (white) excluding fixing bolts, flushing cistern and flush pipe and including EWC Seat cover complete all as directed.

S&F 10 ltrs capacity PVC valveless syphonic action type flushing cistern low level with inlet ball valve float and dual fluash type complete all as specified (Make Cera, F1020106) complete all as specified and directed.

S&F in repairs for 15mm dia of pipe bib taps cast copper alloy, fancy type, chromium plated with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed.

S& F in repairs Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as spfd & directed.

S&F in repairs for 15mm dia of pipe stop valves,fancy type and chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for Unions and fixed .

S&F in repairs PVC connection 15mm dia and 45cm long with two Nos of brass checknuts and washers complete.

S/F in repairs brass chromium plated shower rose 125 mm in size with or without swivel joints any size incl fixing to steel pipe or union, complete all as spfd & directed

Supply and fixing of Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long all as specified.

S&F grating doom 125mm dia with waste hole of PTMT (Min wt 40 gms).

S&F in repairs 600mm long tubular towel rail brass chromium plated 20mm dia, D type 60cm longfixedwith two plugs (Gutties) of 2nd class hard wood embeded in cement mortor 1:3 with MS screwscomplete all as specified.

S& F in repairs PVC mounted 5mm thick bevelled edge looking mirror 600 x 450mm including taking down old fixed with chromium plated brass screws and cup washers

S&F in repair 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to floor

S&F in repair 75 mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to floor

S&F of 110mm dia PVC (SWR) bends

S&F 75mm PVC(SWR) bends any radius with acess door.

S&F of 75mm dia PVC (SWR) Vent cowl

S & F 75mm dia, PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed.

S&F in repairs for 75mm bore dia pipe Stack clamps out of 50mm by 5mm flat iron & 16mm dia round iron stays, including bolts & nuts & securing ends of stay to wall or roof

M&L dismantling water tank of exc 250 ltr and not exc 500ltr Capacity.

S&F rotational moulded polyethylene 500 Ltrs Capacity water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position in SSR Part-I including ball brass valve, with polythelene float and fly nut complete screwed down for iron pipe of 20 mm dia all as specified and directed. .

S&F 20mm dia Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. all as specified and directed.

Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, etc., and getting out in soft soil

Surface excavation n exc 30 cm deep and averaging 15 cm deep and getting out in hard and dense soil.

Excavating over areas, n exc 1.5 m deep and getting out in any type of soil complete all as specified and as directed.

M&L Plain Cement Concrete Type D2 1:4:8 (using 40 mm graded granite stone aggregate) in foundations, filling and mass concrete.

Material and labour for brick work with sub class `B` bricks, old size, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and as directed.

Material and labour for brick work with sub class `B` bricks, old (fire proof bricks) size, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and as directed.

M&L for 150mm thick broken stone or boulders Hardcore of gauge exc 63 mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface all as specified.

M&L RCC M-30 design mix as in beams, lintel band and gable beams including formwork complete all as specified and as directed.

M&L for TMT steel bars 10 mm dia and above, as in reinforcement for concrete, cut to length, bent to shape required including cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm complete all as specified and as directed.

S&F steel work in Steel Gates , grills etc including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S 1161-1979 grade St.-240

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exc 200mm thick (Horizontal or sloping) for fair finished flat surfaces of concrete.

M&L for 40mm thick PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in damp proof course to horizontal or vertical surfaces including necessary form work, applying evenly a coat of blown type bitumen at 1.5 kg per sqm and binding with clean dry sand @ 0.05 cum per sqm including 150 micron thick polythene film laid on a coat of bitumen primer @ 0,30 to 0.50 Kg per sqm complete .

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with soils

Removing Excavated soils not exceeding 50 M and depositing where directed at a level not exceeding 1.5 M above the starting point

M&L for 40 mm thick precast RCC jallies type B0 , 1:2:4 (12.5 mm graded stone aggregate) (measured solid) , including all mould- ings etc complete all as specifed and as directed.

M&L for preparation for newly plastered surfaces and applying three coats of white wash complete all as specified and as directed

M&L 75 mm thick Cement concrete type D 2, 1:4:8 (using 40 mm graded stone aggregate) in sub base of flooring.

M & L for PCC 1:2:4 type B2 (using 40mm graded stone aggregate) 100 mm thick as floor finishing cement concrete surface even and smooth without using extra cement including fixing of plastic dividing strips complete all as specified. Note:- plastic dividing strips measured and paid seperetely.

Supply only plastic dividing strips, 1.5mm thick and width 28mm complete all as specified

Excavating in post holes (or similar holes) each n exc 0.5 cu. M, getting out, returning, filling in and raming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50m and making good surface in soft/ loose soil.

S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S 1161-1979 grade St.-240

S&F steel work in purlins including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S 1161-1979 grade St.-240

S&F steel work in pillars trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S 1161-1979 grade St.-240

S&F plates (plain or chequered) channels. Square cut or notched ) (ordinary and counter sunk) forming holes, without any attachment, Fe 410-W

S&F mild steel bolts, purpose made, with hexagonal or square head one end and screwed the other end to be fitted with washer and one hexagonal or squre nut n exc 15cm long 12mm dia

S&F mild steel bolts, purpose made, with hexagonal or square head one end and screwed the other end to be fitted with washer and one hexagonal or squre nut exc 30cm long and dia 25mm

M&L two coat synthetic enamel paint over a coat of red oxide primer on new steel surfaces of any des-cription, over 10cm in width or girth, not otherwise described

S&F Prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws.

Supply & fixing 15mm Bib taps, chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed by the Engr-in-Charge.

Surface dressing n exc15 cm deep in soft/loose soil.

M&L for PCC 1:4:8 type D-2 100mm thick (40mm thick stone agg) as in sub base of floor.

M&L for PCC 1:2:4 type B-2 100mm thick (20mm thick stone agg) as in finishing surfaces of concrete topping even and fair (without using extra cement) of floor.

M&L for Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound grade 'A' complete

M/L sand cushioning 50mm th including watering and consolidation for laying interlocking blocks

M&L machine pressed pre cast conc interlocking paver block any shape & size conforming to IS15658-2006 of 60mm thickness M35 grade using grey cement & no pigment.

M/L PCC (1:2:4) type B1 using 20mm graded stone agg in plinth courses, string courses, parapets, kerbs, bed plates and the like including weathering slightly rounded or chamfered angles and throating, as directed

S&F Anodised Aluminium frames powder coated for doors, windows, ventilators with one or more rebated including joining cleats for fixing complete etc complete as specified.

E/M Portion Taking down carefully copper/ aluminium point wiring (light, fan, socket or power) complete, including fitting & fixtures such as switches with board, ceiling roses, pendents, bell/ buzzer, bell push, lamp holders, regulators, sockets, light fittings etc., removing material from site and making good to the disturbed surfaces of walls, ceiling, floors etc. including making good the disturbed surfaces and paint touch up to match with the existing surface complete all as specified and as directed.

M&L for Point wiring complete with two runs of 1.5 sqmm single core PVC insulated FR-LSH cable 1100 volts grade with multi-stranded copper conductors, drawn through and including PVC double locked Casing & caping including provision of 1.5 sqmm, FR-LSH, PVC insulated copper cable as earth continuity conductor connected to common earth dolly, including PVC rectagular box for mounting switches / sockets / regulators etc. with 3 mm thick plastic laminated sheet cover of suitable size as required at site complete all as specified and as directed Finolex/Havells/RR Kabel Make of caping/casing & PVC boxes :- Prestoplast/Finolex/supreme

(a) One light/Fan Point controlled by one way switch .

(b) One Call bell point controlled by one, one way switch.

(c) One 3 pin socket outlet 5 Amps on the same board with other switches.

(d) One 3 pin socket outlet 5 Amps on the Independent board.

All as per item No 113 here-in-before but with 2.5 Sq mm for 3 pin 15 Amps socket point controlled by one switch on independent board and 2.5 Sq mm copper conductor green in colour as earth continuity conductor connected to common earth dolly complete all as specified and as directed.

M&L for Switch piano flush type single pole, one way 5A Make:- Havells/Legrand/Anchor

M&L for Socket outlet, 2 in 1, 3 pin 5A flush type Make:- Havells/Legrand/Anchor

M&L for Switch Socket combination, 2 in 1, 5 pin 5A flush type Make:- Havells/Legrand/Anchor

M&L Switch socket combination 2 in 1, 5A/16A, 5 in 1 flush type Make:- Havells/Legrand/Anchor

M&L for stepped type electronic fan regulator 100/120 Watt socket size flush type on the existing phenolic laminated sheet etc. Make:- Havells/Legrand/Achor

M&L for Bell push, flush type, 5 amp

M&L for Bell, AC, 230 volts, single pole complete all as specified and directed.

M&L for ceiling rose 3 terminal PVC/Polycarbonate isolated body complete all as specified and directed. Make:- Havells/Legrand/Achor

Taking down existing burnt aluminium/ copper sub main wiring and M&L for sub main wiring with two runs of 4 Sq mm and one run of 4 Sq mm for earth wire with multi standard copper conductors, 1100 volts grade, drawn through and including PVC double locked Casing & caping including complete all as specified and as directed. NOTE:- two runs of 4 Sq mm + one run of 4 Sq mm and one run of PVC casing & capping and its accessories of suitable size shall be measured as one unit length .Make:- Finolex/Havells/RR Kabel Make of caping/casing :- Prestoplast/Finolex/supreme

S&F for , IP>= 20, Class-I, LED Light fitting 1 x 20 watt (4 Ft), 240 V, PF-0.9, CRI >= 80, CT>= 6500 K, Wall/ Surface mounted, intergrated type with all accessories internally prewired and incl connecting up with and incl twin/ three core twisted flexible copper conductor cable of suitable size in and incl flexible hose from ceiling rose to fitting complete all as specified and as directed. Make : Crompton Geaves Cat No -CCS-102-20-65-SL-DP-NWH/ Bajaj/ Philips.

All as per item No 124 above but 10 watt LED, 2' batten, Wall mounted with polycarbonate housing/ batten. Make Havells Cat No LHEXBQP5IN1W009 or equivalent in Bajaj/Philips

Supply , fixing and testing in replacement of LED bldg Street light fitting of capacity 20 watts, CRI > 70, Power factor > 1.95, colour temp 5700 K, Luminous effieciency not less than 100 lumen/watt, 6000 Lumens output, IP-66 protection including electronic driver (SMPS based constant current supply with < 10% THD, output open/short circuit protection, phase to phase protection, over voltage protection, surge voltage protection etc) unit suitable for working volt 140-270 V AC, 50 Hz, pressure die cast aluminium housing and finishing epoxy white powder coated grey colur after phospho chromate treatment with all accessories including GI bracket MS clamps,nuts,bolts and washers etc and connecting up complete and all as specified and directed by Engr-in-Charge.Make : CG, Cat No- LSTS-20-CDL-M/ Bajaj/ Philips

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm sweep complete all as specified all as directed.

Taking down Exh/Ceiling fan of any sweep carefully from its installed position, dismantling complete, cleaning all dust, applying grease for bearing, painting of fans complete with superior quality synthetic enamel paint by spraying including filling cavaties with filler, after cleaning all dust, reassembling the fan and blades, hanging/ fixing the fan in its original position and testing on completion complete all as specified and as directed.

M&L for rubber bush with clamping set, comprising GI bolt, nut and split pin complete all as specified and as directed.

M&L for replacement of capacitor 2.5 Mfd incl making electrical connection complete all as specified and as directed.

M&L for replacement of steel ball bearing/bush of suitable size compatible to the existing ceiling fan/Exhaust Fan complete all as specified and as directed.

M&L for copper rewinding for suitable size complete to the existing ceiling /Exhaust fan complete all as specifed and as directed.

M&L for MCB Distribution board double door type SPN 12 way, sheet steel, powder painted, with copper bus bar neutral link & earth bar etc. and fixing MCBs of various rating capacity including taking down old unsv MCB DBs complete all as specified and as directed. Make:- Legrand Cat No 607711 or equivalent in ABB/Siemens

M&L for MCB SPN 32 Amps, 230 volts, 50 Hz suitable for fixing in MCB DB 'C' series incl taking down old unsv MCB complete all as specified and as directed. Make:- Legrand Cat No 408636 or equivalent in ABB/Siemens

M&L for MCB SP 6-32 Amps, 230 volts, 50 Hz suitable for fixing in MCB DB 'C' series incl taking down old unsv MCB complete all as specified and as directed. Make:- Legrand Cat No 408587-95 or equivalent in ABB/Siemens

Taking down burnt unsv LT UG cable of any size and M&L for laying of LT UG cable, XLPE insulated, galvanised steel strip or wire armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area of 10 sq mm, 2 core complete all as specified and as directed. NOTE :- (i) Excavation and earth work, sand cushioning, cable protection cover, pipe etc. shall be measured and paid seperately under relevant items.

M&L for spread fine river sand in trenches complete all as specified and as directed. NOTE: For measurement purpose, punned down thickness shall only be taken.

M&L for laying brick sub class 'B' old size burnt bricks for cable protection of size 230mmx115mmx75mm complete all as specified and as directed

Supply & laying tubes ' light grade' galvanised, with clamps suitable fixed complete to walls, poles, ceilings for protection of cables of size 40 mm dia bore including taking out unsv GI tubing complete all as specified and as directed. Make:- Jindal/TATA/Prakash surya

M&L for earthing complete with galvanized steel earth plate electrode of size 600x600x6mm thick buried directly in ground (earth pit not less than 2.25m deep below the normal ground level) with top edge of the earth plate not less than 1.5 mtr below normal ground level connected to galvanised earth lead wire 4 mm dia as earth lead connectd by means of bolts, nuts, washers and check nuts all as shown in electrical plate No 3 of MES SSR Part-I, including testing on completion complete all as specified and as directed.

Shri Atoshe Tuccu

SHRI BANARSI PRASAD

Shri B K Ukil