SPL REPAIR TO WATER SUPPLY PUMPS AGAINST BER AT OLD CANTT AND SPL REPAIR TO STREET LIGHTS ALONGWITH PERIMETER WALL FROMMAIN GATE TO PT GROUND TO GATE NO 5 GG FORT UNDER GE AMRITSAR

Amount

M&L for taking out of submersible pump and motor of 50-60 HP capacity including flange column pipes with chain pulling arrangement and engaging sufficient manpower to ensure safety of plant as well as working persons including disconnecting of delivery main lines and electric connections and lowering the new pump including flanged column pipe and reconnecting the delivery main lines and electric connection of the same complete all as specified and directed.

All as per Srl item no.01 above but for sumersible pump and motor of 35 to 45 HP capacity.

All as per item no.01 above but for sumersible pump and motor of 25 to 30 HP capacity.

Supply and fixing of Submersible pump with motor complete set of 55 HP capable of delivering below mentioned dischargeof specified head water cooled copper rotor motor sync. Speed 2880 rpm at rated 415 volts with wide voltage variation of +5% and -15% , 3 Phase , 50 Hz. A.C. power supply with QC8 mixed flow pump suitable for 300mm/350mm dia deep borewell , 2100 LPM & 70 meter water Head and conforming to IS 8034 and IS 9283. Bore hole with normal clean drinking water. Recommended to operate upto 40 degree centigrade at mean sea level complete all as specified and directed.

Supply and fixing of Submersible pump with motor complete set of 45 HP capable of delivering below mentioned discharge at specified head water cooled copper rotor motor sync. Speed 2880 rpm at rated 415 volts with wide voltage variation of +5% and -15%, 3 Phase , 50 Hz. A.C. power supply with QC8 mixed flow pump suitable for 300mm/350mm dia deep borewell , 1800 LPM & 70 meter water Head conforming to IS 8034 and IS 9283. Bore hole with normal clean drinking water. Recommended to operate upto 40 degree centigrade at mean sea level complete all as specified and directed.

Supply and fixing of Submersible pump with motor complete set of 35 hp capable of delivering below mentioned dischargeof specified head water cooled copper rotor motor sync. Speed 2880 rpm at rated 415 volts with wide voltage variation of +5% and -15%, 3 Phase , 50 Hz. A.C. power supply with QC8 mixed flow pump suitable for 300mm/350mm dia deep borewell , 1400 LPM & 70 meter water Head conforming to IS 8034 and IS 9283. Bore hole with normal clean drinking water. Recommended to operate upto 40 degree centigrade at mean sea level complete all as specified and directed.

Supply and fixing of Submersible pump with motor complete set of 25 hp water cooled copper rotor motorsync. Speed 2880 rpm at rated 415 volts with wide voltage variation of +5% and -15%, 3 Phase , 50 Hz. A.C. power supply with QC8 mixed flow pump suitable for 300mm/350mm dia deep borewell , 850 LPM & 70 meter water Head conforming to IS 8034 and IS 9283. Bore hole with normal clean drinking water. Recommended to operate upto 40 degree centigrade at mean sea level complete all as specified and directed. Note for item No 4 to 7 above : (a) Lowering of the pump including connecting the delivery pipe and making electric connection are included in the quoted rates of respective item of the BoQ. (b) Old Unservicable submersible pump with motor shall be deposited to the MES Store Yard. (c)The discharge outlet of the pumset should be 100mm/150mm dia or as per manufacturer specification. (d) The pump shall be purchased only from the authorised dealer of company. (e) Miscellaneous work such as modification/alteration of reducer and nipple as per delivery pipe and other fabrication work as required for fitting the pump is included in the quoted rate of the items. (f) Manufacture test certificate and technical data sheet /performance report shall be submitted by the contractor.

Supply and fixing in replacement HRFR,PVC insulated 3 Core industrial grade HV flat submersible cable copper conductor 1100 V size 16 Sqmm all as specified abd directed by Engr-in-Charge.

Supply and fixing in replacement HRFR,PVC insulated 3 Core industrial grade HV flat submersible cable copper conductor 1100 V size 10 Sqmm all as specified abd directed by Engr-in-Charge.

Supply and fixing in replacement HRFR,PVC insulated 3 Core industrial grade HV flat submersible cable copper conductor 1100 V size 6 Sqmm all as specified abd directed by Engr-in-Charge.

Supply and fixing in replacement, for MS flanged pipe of size 150 mm dia heavy duty 'C' class with necessary MS bolts, nuts and washers, packing material, rubber gaskets, pressure gauge for lowering etc as per IS: 1239 Part-I 2004 complete all as specified and as directed by Engr-in-charge. Note : Cost of liftimg the pump ,removing old pipes , fixing the new pipes and lowering the pump if required is included in the quoted rates.

Supply and fixing in replacement, for MS flanged pipe of size 100 mm dia heavy duty 'C' class with necessary MS bolts, nuts and washers, packing material, rubber gaskets,pressure gauge etc for lowering as per IS: 1239 Part-I 2004 complete all as specified and as directed by Engr-in-charge. Note : Cost of liftimg the pump ,removing old pipes , fixing the new pipes and lowering the pump if required is included in the quoted rates.

Supply, laying and testing in replacement cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 sq mm 3.5 core all as specified and directed.

Supply, laying and testing in replacement cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 70 sq mm 3.5 core all as specified and directed.

Excavation in trenches not exc. 1.50 m wide and not exc. 1.50 m in depth for foundation etc. or for laying of pipes and fittings, cables, HT / LT poles, stay assembly etc including forming bottom surfaces to required level and slope and getting out in hard / dense soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer as in hard / dense soil complete all as specified and directed.

Removing surplus excavated material (SOIL) to distance not exc. 50 m and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed.

Material & labour for sand filling in trenches for cable protection including necessary punning and consolidation as required complete all as specified and directed.NOTE:- Punned thickness only will be considering for payment.

Supply and laying burnt brick sub class 'B' modular size, for cable protection laid length wise perpendicular to the axis of cable complete all as specified and directed.

Supply, laying and testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor, Size 16 Sqmm 4 core complete all as specified and directed.

Supply, laying, jointing and testing XLPE insulated and PVC sheathed, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 10 Sqmm 2 core with cable gland complete all as specified and directed.

Supply and fix 60 Watt, LED light fitting, made of pressure die cast aluminium alloy for housing heat sink for effective thermal management, corrosion resistant, dust & vermn proof with IP 66 and IK 07 protection, epoxy powder coated, tempered proof toughened glass, luminous efficacy of greater than 110 lumen/watt with PC lens for ensuring uniform distribution of light overall system, lumen should be greater than 9000, operating voltage 110-300 volts with inbuilt SPD protection of 5 KV, power factor minimum 0.95 ambient, working temperature (-) 10 to 50˚, short circuit & over voltage protection, phase to phase protection, accreditation LAB, CRI minimum 70, CCT between 5000 to 5700 K, estimated life span minimum 50,000 hours complete all as specified and directed. Note:- (i) The contractor shall submit LM 79 & LM 80 reports from NABL and LED Chip manufacturer respectively. (ii) The contractor shall submit 05 years warranty of fittings towards ite performance and free replacement of defective parts. (iii) The light fittings shall be purchased only from the authorised dealer of the company. (iv) The T&P required for replacement of lights such as telescopic ladder/hydra crane or any other equipement shall be brought by the contractor without any extra cost.

S&F of street light fitting brackets 1.5 meter long made out of galvanized iron pipe of 32/40/50 mm dia size as suitable for LED fittings light grade complete with nut bolts washers and clamps of MS for fitting the bracket with steel tubular /PCC as required at site etc inclusive of one primer coat one under coat and one finishing coat of silver paint complete all as specified and directed by Engr-in-Charge. NOTE :- Removal of LED fitting , keeping safe and refixing the same after changing the street light bracket is included in the quoted rate.

S&F of Junction Box shall be insulated and made out of Polycarbonate with glass fiber reinforced. The size should be not less then 200 X 160 X 98 in mm cat. Part no KF5255. The Polycarbonate JB shall be environment friendly, recyclable, UV resistant, halogen & silicon free, anti acid & anti corrosive. The JB shall be rated for Degree of Ingress Protection IP 66 in accordance with IEC 60529. The gasket material shall be Polyurethane and the gasket shall be internally embedded. The JBs shall be complies with requirements of the standards IEC 60998-1, IEC 60998-2-1, IEC 60670 –22 & IEC 60670 – 2-5. The JB color according to RAL 9011. The manufacturer of Junction Box / Enclosure shall submit a copy of IEC Certificate. For better safety the Polycarbonate encl shall be fire retardant & self-extinguishing in accordance with IEC 60 695-2-11, DIN VDE 0304 Part 3, UL Subject 94 for Flammability V-2. It should be tested at Glow Wir test for 960 deg. Cent. The impact strength of polycarbonate enclosures / boards i.e. the Degree of Protection against Mechanical load shall be in accordance with EN 50298-98 for IK 08. including one single pole MCB 6A Manufacturer should submit routine test certificate for PJB.

M&L PVC insulated PVC sheathed copper conductor (flexible)multi stranded copper conductor wire 2.5 sqmm size twin core complete for drawing through pole for making connection to street light fitting provided on poles upto junction box incl thimbles.

M&L PVC insulated and PVC Sheathed Aluminium conductor wire 2.5 sqmm size twin core complete for making connection to street light fitting.

Excavating in trenches in soft/ loose soil not exceeding 1.50 m wide and not exceeding 1.50 m in depth for foundation for pipes, walls, cesspits, manholes, pier holes, cables etc not exceeding 10 Sqm on plan and not exceeding 1.50 m in depth and getting out complete all as specified.

Returning, filling in, spreading, leveling, watering and well ramming in layers not exceeding 25cm thick each complete all as specified.

Removal of excavated soil to a distance not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point complete all as specified.

Supply and laying old size as sub class 'B' bricks, laid flat in trenches over the cable along the length of cable and bricks perpendicular to the direction of cable adjacent / abutting each other compete all as specified . and directed by Engr-in-Charge.

Material and labour for sand cushioning under floor, for laying cables with a layer of fine sand 8 cm thick before laying the cable and 15 cm after laying the cable in trenches to cover under ground cable complete all as specified and directed. Note :- Punned down thickness of sand shall be considered for measurement.

S&F street light distribution outdoor panel with canopy single door vertical type made out of CRCA MS sheet with thickness not less than 3 mm surface with insulated material like polysofer or with epoxy powder coating surface mounting TPN 4 way,415 Volt with copper bus bar rating 200Amps for R,Y,B,N phases dust and vermin proof suitable for incorporation of MCCB and IP 52-IK09 protection with and incl 100Amps 16KA 4 Pole MCCB including angle iron support legs and foundation work for the legs (including excavation and doing PCC 1:2:4). The size of the panel should not be less than 600mmx400mmx200mm, and height of the panel should be atleast 300mm above ground level. the angle iron for support should be minimum 35 mm x 35mm x 5 mm thick.

S&F in replacement of galvanised iron pipe of 50mm nominal dia light grade fixed to poles with clamps nuts, bolts washers or laid under road cutting or fixed to wall incl painting two coats of aluminium paint over coat of red oxide paint complete all as sprecified and directed by Engr-in-charge.

Cleaning and preparation of old painted surface of steel pole upto 9 Mtr long excluding planting depth complete and painting with one coat of aluminium paint including channels street light brackets cross arms anti climbing devices and making black & white strips with synthetic enamelled paint 30 Cm height, each alternative strip upto 1.5 mtr height writing pole numbers as per existing practice, making round base of dia 120mm by using yellow colour and marking the pole numbers of letter size equal to 70mm in height by using black colour with stencil complete all as specified and directed by Engr-in-Charge. NOTE :- The T&P required for painting such as telescopic ladder/hydra crane or any other equipement shall be brought by the contractor without any extra cost.

Boring of holes under road pavement hard staanding by the help of boring maachine/manually including galvanized iron pipe of dia 50mm for inserting the cable.

ss enterprises

M/S RASHPAL CONSTRUCTION CO

R D Bansal

Bharat Builder