21/HDA/EC-ELECT/2024 2025

Amount

Supply & delivery of LED Street light of following specification: a) 200 W (+/-5%) for each set.(Maximum) b) Lumen output should be minimum 26000 lumen from each set. c) Light must be cut-off or semi-cut off as per IS-1944(Part-I & II). d) Surge protection device must be minimum 10 KV 10 KA. e) The luminaries should be of IP 66 protection. f) In put Voltage of 130 V – 270 Volt, 50 Hz. A.C. supply g) Driver should have in-built protection against open circuit & short circuit. h) Housing should be of Die-cast aluminium housing with epoxy powder coating and having cooling fins for effective heat dissipation. Separate cavity for driver & LED lamp. i) Third party test report from NABL accredited laboratory of LM-79 & IP-66. j) The product should have 5 years warranty period. (Make : PHILIPS LIGHTING INDIA LTD / CROMPTON./ HAVELLS INDIA LTD. / BAJAJ ELECTRICALS LTD.)

Supply, delivery & installation of 9 Mtr. Hot Dipped galvanized Octagonal Pole with G.I 4nos. J- bolt, M-24, 750 mm long, 12nos. of Nuts with 16nos. of washers for foundation and double straight arm of 1.5 M in Length (Refer to the Specification and Drawing in Annexure-I). The rate should include testing at works, including all taxes and delivery the materials at different locations of HDA planning area. (Make : UTKARSH INDIA LTD / TRANSRAIL LIGHTING LIMITED / BAJAJ ELECTRICALS LTD.)

Supply and fixing of SPMCB "B" Curve 1-4 Amp with ISI marked to be placed on a din channel of Pole and supply and fixing of Terminal connector at the suitable location of the pole.

Supply and fixing of Pole numbering Sticker (5" X 3") at the street light pole.)

Lifting of the running Under Ground Cable coming to the looping cable Box upto the top of the muffing above the top of the ground level by drawing through 40 mm dia rigid pvc pipe of superior Quality and tiding the same by no 10 SWG G I wire wiyh the pole including supply of pipe & wire & filling the top of the pipe/pipe hole with bitumen and neat cementing properly (average run- 1.5 mtrs/run X 2 runs per pole).

Straigh through Jointing of cable of different size by compound jointing kit including S&F ferrul, tapes and jointing materials (Brand approved by EIC) 3½ / 4 core 25-35 sqmm cable

Supply and Installation of HDA printed logo suitable 15"×9" on GI Octagonal/tubular Pole , on brick foundation of meter box, feeder pillar box .(3 nos logo p/pole,per meter box,per feeder pillar box.)

Supply & delivery of GI earth Spike (1830 X 20 mm)(Each Pole).(Including installation)

Connecting the equipments to earth busbar including S & F GI (Hot Dip) wire of size as below on wall/floor with staples buried inside wall/floor as required and making connection to equipments with bolts, nuts, washers, cable lugs etc. asrequired and mending good damages (ii) No. 6 SWG

Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc( 0.35 sqm per pole x 8).

Painting the vertical end faces of posts, wheel guards or railing or parapet with alternate bands of different colours as directed by the Engineer-in-charge with approved synthetic enamel paint( 0.35 sqm per pole x 8). (b)Two coats.

Supply of HDPE Plb Duct pipe of size 32/26mm.

Laying of one No. HDPE pipe in underground trench 460 mm wide x 760 mm average depth, including filling the trench with shifted soil,leveling up and restoring surface duly rammed.

Laying only Cable upto 50 sq.mm through existing RCC/Hume/ GI /HDPE Pipe/open masonry trench for single, 2, 3, 3½ & 4 core

Fixing only street light Fitting with suitable tie clamps and MS plate for mounting on Pole/Tower or similar structure.

Finishing of the XLPE/PVC insulated armoured cable ends by soldering with cable sockets and insulated tapes etc., including supplying sockets, soldering materials, tapes etc. and making connection to switch, BDB and BBC etc. i) 3.5 core X 35 sqmm

supply, drawing and Connection of luminaries with 3C X 1.5 Sqmm pvc insulated FR copper conductor through 10 mtr. Poles from looping box to light fittings as required through 19 mm dia 3 mm thick polythene pipe.

Preparation of RCC foundation of 500 mm dia and 1800 mm hight (1500 mm below the Ground Level and 300 mm above the Ground Level) with required rod, cement, chips and sand etc. at the ratio 1:1:5:3 with ground bolt 4 nos for fixing the 10 Mtr Hight G.I Octagonal pole (excluding supply and delivery of 9 M Pole and Nut Bolts).

GST @18% of Total Amount

CESS @1% (Total Amount including GST)