SPECIAL REPAIR REFINED OIL SHED BLDG NO. 314 AND COOK HOUSE BLDG NO. P-99A IN CERTAIN UNITS AT MIL STN JAISALMER

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premise complete all as specified and directed by Engineer-in-charge.

Demolition of cement concrete (un reinforced) in ground floors and pavings n.exc 15 cm thick (below or above ground level) & removing rubbish out side MD land all as directed by Engineer-in-charge.

M &L Squared rubble walling Jodhpur type, brought upto courses, well bonded, bedded and solidly hearted, built in CM 1:6 including with demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc complete all as specified and directed by Engineer-in-charge.

Extra over to stone walling for hammer dressing to face stones and dressing of the face beds & joints as specified of squared rubble walling regular coursed, Jodhpur type, with maximum depression of face from straight edge held against the dressed surface n.exc. 20mm complete all as specified and directed by Engineer-in-charge.

S&F pre-painted galvalume aluminium zine coating GI based corrugated steel sheeting 0.50mm thick any colour having tensile strenght 550Mpa in roof coverings fixed with self tapping screws including dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed by Engineer-in-charge. Note : (i) The fixing of Galvalume roof sheet as in sun-shades & in walls at certain places to be fixed by making of grooves cutting 75mm minimum with making good surface are inlcuded in the cost of item itself. No extra cost shall be paid for the same. (ii) The pattern and design of sunshades to be fixed as per directions of Engr-in-charge.

M&L Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) Fe 410 -W (Gde- E- 250) quality- A with dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and directed by Engineer-in-charge.

M&L 5cm Sand stone slabs in sun-shades, chajjas, shelves, cills, landings, cover stones, templates, etc. n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in lime mortar 1:2 or cement mortar 1:4. including dismantling of Stone slabs in roofs, suspended floors, chajjas, landings, etc., any thickness, jointed in any mortar, complete all as specified and directed by Engineer-in-charge.

M&L for Granite 20mm thick table rubbed and polished in steps, jambs, pillars, window cills, cooking platformsand like in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixure of pigment to match with marble shade of Makrana white complete all as specified and directed.

M&L for Glazed ceramic colour tiles in vertical surface 350x250mmx7mm/ 450X350X7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick rendering in CM 1:4, with dismantling of floor hearth or wall tiling including cement mortar bedding (but not backing, removing serviceable tiles), complete all as specified and directed

M&L for Non-skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:6, with dismantling of floor hearth or wall tiling including cement mortar bedding (but not backing, removing serviceable tiles) all as specified and directed.

M & L Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles laid on and including 15mm thick screed bed in cement mortar 1:6 with dismantling of floor hearth or wall tiling including cement mortar bedding (but not backing, removing serviceable tiles).

S&F Chequered cement concrete tiles 300mmX300mm X25mm thick with grey cement and pigment, rubber moulded, set jointed and pointed in neat cement slurry as in floors/path etc laid over and including 20mm thk screed bed in CM (1:6) complete all as specified & directed by Engineer-in-charge.

M&L non skid ceramic coloured tiles (Jointless) 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles laid over and including 15mm thick screed bed or bedding in cement mortar (1:6) complete all as specified and directed by Engineer-in-charge.

M & L for Chipping of slab/ columns/ beams/chajjas/ parapet/ roof projection/ balcony/ staircase and removing loose mortar with chisel hammer without much impact on concrete surface, clean the surface by sand blasting the surface using river sand with minimum of 6 kg pressure at the nozzle or air blow by electric pressure blower by mechanical compressor, cleaning the exposed reinforcement with wire brushes etc and disposal of debris for all lead and lifts, all complete all as specified and directed.

M&L Machine cut kota stone slab flooring 20- 25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete laid over and including screed bed or bedding layer of 15mm thick in CM (1:6) complete all as specified & directed by Engineer-in-charge.

M&L for rendering 5mm thick readymade plaster on inner/outer walls with approved make by adding 17-19% of potable water by weight of material. Ready-mix plaster shall complies with IS 1661-1972, IS 2250-1965, IS 2402-1963 and confirms the Compressive strength @ 28 Days- 10-12 Mpa/ Bulk density- 1500-1600 Kg/m3. Note :The rate quoted by contractor shall include cleaning of surface, application as per instruction and scaffolding upto 20mtr height all as specified and directed)

S & F Exposed metal frame ceiling with 8mm PVC coated calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600 mm x 600mm grid, Anodised aluminium snap grid of size of grid 605 x 605mm frame work for false ceiling all as specified and directed. Note :- (i) Main tee, cross tee shall be 35x25x1.5mm & 25x25x1.5mm respectively. Angle at end all along the walls shall be 40x25x2mm. (ii) Rate quoted by the contractor shall deemed to inclusive of frame work and Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long including dismantling of wall and ceiling boards (fibre, pulp, insulation boards/ slabs/ blankets, any thickness, including cover fillets, complete all as specified and directed.

Taking down chowkats or frames exc 1.50 sqm but not exceeding 4 sqm each without taking off shutters from the frames including iron mongry.

Taking down chowkats or frames n.exc 1.50 sqm each, without taking off shutters from the frames including iron mongry.

Taking down shutters of any description exc 2.0 Sqm each from the frames including iron mongry.

Taking down chowkhats (without taking down shutters from the frames) of any description n.exc 1.5 sq. m each complete all as specified & directed by Engineer-in-charge.

S & F for 30mm thick Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides supplied and fitted to chowkats

S&F 35 mm thick Glazed and skeleton shutters second class hard wood, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats

S&F Butt hinges, 100mm medium weight, cold rolled mild steel, and fixed

S&F Anodised aluminium alloy handles cast type, each 150mm long

S&F Aluminium anodised, barrel tower bolts 125mm long of extruded section and fixed

S&F for Aluminium alloy, anodised, sliding door bolt of length 300mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

M&L for Powder coated aluminium frame for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified.

S & F Aluminium door shutters with powder coating of any colour (Thickness or powder coating not less than 50 micron), aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, tower bolt, mortice lock, anodised aluminum snap beading screws etc. complete all as specified

S & F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engr-in- charge.

S & F Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples in repairs

Hacking out old broken glass (any thickness, size, quality or description) from metal frame exc 1.5 sqm including punching or drilling out old glazing pins/ springs clips and providing and fixing new ones and S & F 3 mm thick plain glass and glazing with oil putty in squares not exceeding 0.5 Sq. M in each pane.

S & F 4.8mm thick Sheet glass, ordinary quality and glazing with oil putty in square exc 0.50 Sqm in each pane, all as specified and as directed.

S & F Solar control film 25 micron reflective type exc 1.50 Sqm, sticked to glass panes as per instructions of manufacturers

Supply and fixing factory made 18mm both side laminated HDHMR board in modular kitchen carcasse and other similar works made of minifix joint with 1mm same colour edge banding including fixed with nut, screws and washers fevicol, nails including dismantling of old kitchen cabinets or similar works complete all as specified and directed by Engg-in-charge.

S & F powder coated stainless steel SS 304 sensys intergrated soft cose hinges having size 103x64mm finish of nicle/silver complete all as specified and directed by Engr-in-charge

S&F in repair, Aluminium (Die cast) body Door closer hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed

S/F Solid PVC door frame of size 50x47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S. Square tube suppling and fixing in opening as per specification and drawing

S/F 30mm thick of Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, uppling & fixing in the frame at site as per specification & drawing etc all as specified and directed.

S&F in repairs of harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc.

S&F in repairs tubular towel rail brass chromium plated 20mm dia D type 60cm long complete all as directed.

M&L for rendering 15 mm thick readymade plaster on inner/outer walls with approved make by adding 17-19% of potable water by weight of material. For thickness above 15 mm it is recommended to be applied in multiple layers. Ready-mix plaster shall complies with IS 1661-1972, IS 2250-1965, IS 2402-1963 and confirms the Compressive strength @ 28 Days- 10-12 Mpa/ Bulk density- 1500-1600 Kg/m3. Note :The rate quoted by contractor shall include cleaning of surface, application as per instruction and scaffolding upto 20mtr height all as specified and directed)

M&L 50 mm thick nominal mix M15 concrete 1:2:4 type B1, (using 20mm graded stone aggregate) in plinth protection and path laid in alternative bays finished even and smooth without using extra cement, complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc.complete all as specified and directed.

M & L for applying bond coat cum waterproofing on the prepared old surface of concrete/masonry to receive new Readymade plaster/polymer mortar/polymer modified mortar with two coats of Slurry- @ approximately 2- 2.5 m2 / litre depending on substrate porosity of Fosroc Nitobond SBR300 or equivalent Equivalent etc as per manufacturer specifications. Laying of reinstatement readymade plaster/polymer mortar shall be completed within the overlay time of bonding coat. This bond coat act as bonding agent between old and new concrete r. Note :The rate quoted by contractor shall include cleaning of surface, application as per instruction and scaffolding upto 20mtr height all as specified and directed)

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC)

Each Set

medium grade 3 meter long tapers at bottom & provided 12 mm holes (staggered) at 75 mm centre to centre up to 2.5 meter of length from bottom , burried directly in ground filled with 45 cm alternate layer of chemical magnisium sulphate, charcoal & salt up to ground level connected to 4.00 mm dia GI wire as earthing lead up to 7.5 mtr by means of bolt and nut, check nuts and washer of galvanized iron or steel including brazing work and 15 mm dia light grade pipe for earth lead protection connected to electrical equipment and earthing test point , earth dolly and earth chamber as shown in elect plate No 2 of SSR Pt-I including all necessary earth work, excavation, earth chamber with PCC 1:3:6, Type C1 and RCC chamber cover of PCC 1:2:4 with handle and 20 mm dia GI watering pipe with funnel and wire mesh etc and testing on complete all as specified and directed Engr-in-Charge.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. complete all as specified & directed by Engineer-in-charge.

M&L for preparation of newly plastered surfaces of wall and applying two coats of distemper oil emulsion over chalk whiting on plastered surfaces, preparatory to distempering, complete all as specified and directed.

M & L for Preparation of new plastered surfaces of ceiling and applying three coats of white wash comp

lete all as specified & directed.

M & L for Preparation of new plastered surfaces of wall incl and applying two coats of cement base paint complete all as specified

M & L for Preparation of old plastered surfaces of ceiling incl Washing, rubbing down and stopping of distempered and painted and applying three coats of white wash including complete removal of existing tretment complete all as specified & directed.

M & L for Preparation of old plastered surfaces of wall incl Washing, rubbing down and stopping of distempered and painted and applying three coats of white wash including complete removal of existing tretment complete all as specified & directed.

M & L for Preparation of old plastered surfaces of wall incl Washing, rubbing down and stopping of distempered and painted and applying two coats of cement base paint including complete removal of existing treatment complete all as specified & directed.

M&L Preparation of old steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coats of Synthetic enamel (ordinary tint) (each coat)

S&F in repair, 1000 ltrs capacity white colour three layer rotational moulded polythene water storage tank (Cylinderical vertical with closed top) hoisted and fixed in position with 20mm bore dia ball brass valves high pressure ,with polythene float and flynut screwed for iron pipe or brass ferrule, all as specified in SSR Part-I, complete including dismantling of existing tank with float valve.

S&F in repairs Gun Metal globe or gate valve with iron wheel head, screwed both ends for iron pipe, 20mm bore complete all as directed.

S&F in repairs Kitchen sink with drainage board made of stainless steel 1mm thick with plugs, washers and wastes, incl bedding in cement mortar on to dwarf wall or incl fixing cantilever brackets and connecting union to pipe, over all size 915x460mm bowl size 410x330x160mm complete

S&F in repair, Vitreous china wash basin pedestal type, white, flat back, size 550x400 mm excluding taps, chain and plug and porcelain stopper but including CP waste coupling & brackets and fixed complete all as specified and directed.

S&F in repairs 15mm dia Bib taps cast copper alloy chromium plated with crown or capstan head, screwed down, high pressure screwed for iron pipe complete all as directed.

S&F in repairs 15mm dia Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, complete all as directed.

S&F in repair, PVC connection pipe 15mm dia, 450mm long with PTMT check nuts and washer on both ends complete all as directed.

S&F 15mm dia medium grade GI tubing with all fittings and fixtures complete fixed to walls, ceilings etc including taking down of old existing GI tubing, all as specified and as directed.

S&F 20mm dia medium grade GI tubing with all fittings and fixtures complete fixed to walls, ceilings etc including taking down of old existing GI tubing, all as specified and as directed.

S&F in repair of Orissa pattern vitreous china squatting pan white of size 580x440mm with integral footrest (Excluding flushing cistern and flush pipes) but including concrete bedding and P or S trap as required including PVC pipe up to finished floor level to connect flush pipe, making good all the disturbed surfaces to match the adjoining complete all as directed by Engr-in-Charge.

S&F in repairs 10 ltrs capacity PVC low level flushing cistern with inlet, ball valve, float, handle including fitting and fixtures and taking down the old damaged cisterns and providing connections to WC and flush pipe without any damage to the existing fittings, complete all as all as directed.

S&F for CP peg set with 6 points fixed to walls Complete

S&F for CP towel ring square shape fixed to wall complete

M&L for 75mm thk cement concrete 1:4:8 type D2 using 40mm graded stone aggregate as in subbase of flooring/hard standing as specified

M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specififed and directed.

S&F Plate racks made of stainless steel 1mm thick with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and overall size 750mmx 600mm as specified and directed by Engr-in-Charge.

S&F in repairs brass chromium plated shower rose with swivel joints 125mm dia with 18mm dia chromium plated pipe complete all as directed.

S & F 110 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints laid in floors or trenches in repair.

S& F PVC (SWR) vent cowl 110 mm in repair.

M & L for 150mm dia Reinforced concrete pipes, class NP2, laid and jointed complete with collars with Concrete bed type D2 (1:4:8) using 40mm graded aggregate to drain pipes of 150mm dia including packing under and completely surrounding pipes with concrete after they are laid and tested; in with demolition and breaking of 150mm dia up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar

All as per item No. 15.00 above but as in skirting, steps etc in vertical surfaces with 10mm thick rendering as in backing coat in CM 1:3 complete all as specified

M & L Cement concrete type D2 (1:4:8) using 40mm graded aggregate as in foundations, filling and mass concrete

Providing, precast cement concrete Type B1 1:2:4 (20 mm graded aggregate) in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings, kneelers, apex stones, pier caps, columns, posts,boundary pillars, bed plates, pintle blocks, anchorage blocks, bonders (for stone walling), corbels, brackets, etc.(of any section indicated), with plain fair faces, including chamfers, weatherings, throating etc. and setting in cement mortar 1:6 complete with joints to match complete all as specified.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth in soft disintegrated rock and getting out , all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point

S&F in repairs cast iron nahani trap with CP grating including jointing to waste pipe in cement mortar, diameter of out let 75mm bore fixed in cement concrete type B1 (1:2:4) complete all as directed.

M&L Parking ceramic tiles exterior grade 300 x 300 x 10mm including 15 mm thick screed bed in CM 1:6, set and jointed in neat cement slurry and pointed in coloured cement to match with dismantling of floor hearth or wall tiling including cement mortar bedding (but not backing, removing serviceable tiles)all as specified & directed.

M&L for 25mm thk PCC (1:2:4) type B0 (using 12.5mm graded stone aggregate) as in subbase of floors, on roof top as padding & finishing the surface even & smooth without using extra cement including complete removal of existing roof treatment complete all as specified & directed by Engineer-in-charge.

M&L for 25mm thk PCC (1:2:4)

type B-1 (using 20mm graded stone aggregate) as in subbase of floors & finishing the surface even & smooth without using extra cement complete all as specified and directed by Engineer-in-charge.

Dismantling/Demolition of existing roof terracing of cement/brick concrete(un-reinforced) and existing water proofing treatment of any thickness in any position on top of roof of building, cleaning surface of roof with brush/mechanical brush and with water throughly to romove all dust/dirt and loose particles to expose bare concrete roof slab and romoval of rubbish/demolished material out side MD land complete all as specified Note : Demolition should be done by chiselling.

M&L for providing 3 mm thick APP modified memberane over RCC roof with the following specifiations :-

M&L for PCC (1:2:4) Bo using 12.5 mm graded stone aggregate as in levelling padding course over RCC roof surface including rounded or chamferred on edges etc., with approved water proofing compound all as per manufacturer's instructuions on the roof surface to achieve requisite slope all as specified and directed. (Note :- Supply only water proofing compound shall be measured & paid separately).

Supply only Liquid water proofing compound

M &L Pre-cast cement concrete block type C1 1:3:6 20mm graded masonry with solid blocks, exc. 10 cm in width and setting in cement mortar 1:6 including demolition of PCC block masonry, built in Cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles etc complete all as specified and directed.

S&F steel ventilators with top hung shutters fitted with box type hinges including MS peg stays, MS handle and glazing bars dovetailed or welded for receiving glass including painting with one shop coat of zinc chromate primer,and cutting holes in wall for fixing the window lugs in PCC 1:2:4 type B1 using 20mm graded aggregate and making good the disturbed surfaces in CM (1:3) and applying two coats existing wall finishes to match with existing colour complete all as specified and directed by Engineering –in-Charge. Note : The rates quoted are inclusive of making good all the disturbed surfaces to match with the adjoining surfaces and necessary scaffolding etc up to 4th floor.

Dismantling wrought iron or mild steel work of any description not otherwise provided for

M&L Mild framed works such as angles, tees , channels, etc as in fenching posts large and small gates and grills , gratings and chainlink fenching etc, including hanging gates in pillar with proper pintle hinges, stops, hand made sliding bolts ,etc complete.

M&L Preparation of new steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coats of Synthetic enamel (ordinary tint) (each coat)

M&L for PCC 50 mm thick type C1 1:3:6 (20 mm graded stone aggregate) laid in alternative as in plinth protection including finished the surface even & fair without using extra cement

M&L Preparation on new wooden surfaces over 10 cm width/girth and applying 2 coat of synthetic enamel paint over a coat of pink primer.

Taking down carefully surface aluminium or copper point wiring with PVC casing-caping (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc and making good disturbed surfaces complete.

Taking down the existing unserviceable main switch / cut out / DBs of any type / capacity / description as existing at site including MCBs any type and capacity making good the disturbed surfaces to match with the existing finishes all as specified.

One light point controlled by one switch

One ceiling fan/exhaust fan point controlled by one switch

M&L for applying to the damaged concrete portion of slab/ columns/ beams/ chajjas/ parapet /roof projection/ balcony/ staircase with single component, fiber reinforced, dual shrinkage- compensated thixotropic, cementitious ptch repair mortar Sika monotop 122F (having the technical parameters mentioned in material specifications ) capable of applying up to 20-25mm thick in double layer or multiple layers initially by hand and finishing with troweled carefully compacting the same around the rebar and finishing to bring it in line with existing concrete surface with an average specified thickness complete all as specified and directed by Engineer-in-charge.

M&L Point wiring used approved colour coding as per IS (Red, Black and Green) for single phase circuits), with multi-stranded copper conductor 1.5 sqmm nominal cross -sectional area, single core, PVC insulated and unsheated FRLS cable 1100 volts grade, ISI 694 marked with valid CML No. in and including medium grade, PVC concealed conduit MMS, ISI marked of dia not less than 20 mm and conduit accessories conceled in wall/roof/floor etc, ISI marked with valid CML No. (IS-9537 - 1983 for condits and IS : 3419 - 1976 for conduit accessories) with terminated to new pressed flush metal boxes readily available cover with outer plates inner plates et, suitable for mounting modular type switches, socket fan regulator etc PVC insulated multistanded copper conductor 1.5 Sqmm nominal cross sectional area single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for the following :- Note : Modular switch and socket shall be measured and paid separately.

M& L Providing type B1 (1:2:4) (20mm graded aggregate) precast ce- ment concrete in win- dow or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, pier caps,columns, posts, boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone wallin). corbels, brackets, etc. (of any section indicated), withplain fair faces, including chamfers, weatherings, throat- ing etc. and setting in mortar complete with joints to match and set in CM 1:4.

S&F modular switch one way 6A, 1 module .

S & F for MCB DB SPN 4 way double door IP 43 complete prewired including Bus Bar etc suitable for operation on 240 volt 50 Hz AC supply including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed .

One socket outlet 6 amp controlled by one switch on the same board with other switches.

All as per item No 104.00 here on before but with copper conductor cable of nominal class area 4.0 sq mm for phase ,neutral & earth for power socket point 15 A .

S & F for MCB DB SPN 8 way double door IP 43 complete prewired including Bus Bar etc suitable for operation on 240 volt 50 Hz AC supply including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed .

Supply and fixing MCB's single pole and neutral 32 Amps, 240 Volts,10 KA rapturing capacity 'C' curve.complete all as specified & directed.

Supply and fixing MCB's single pole 10 Amps to 32 Amps, 240 Volts,10 KA rapturing capacity 'C' curve.complete all as specified & directed.

M & L for submain wiring with approved colour code/as per IS (Red,black & green for single phase)concealed conduit circuit with two single core PVC insulated cable with multistranded copper conductor of nominal cross sectional area of 4.00 Sqmm (FRLS) in conduit including one run of PVC insulated multistranded copper conductor nominal cross sectinal area of 4.00 Sqmm (FRLS) of continous earth wire green in colour complete all as specified and directed by Engr-In-Charge. (Note :- Two runs of 4.00 Sqmm cable & one run of 4.00 Sqmm cable shall be paid as one unit length)

S$F Ceiling rose, three terminals PVC/polycorbonate, isolated body.

S&F modular socket 6A-2/3 pin combined 2 module.

Supply and fixing LED lights fitting 1x 18W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

S&F modular switch socket combined 6A/16A , 6 pin, 3 module

Taking down ceiling fan / Exhaust fan/Wall fan/Air circulator fan of any sweep sealing cable ends dismanting blade and removing fan and blade to store complete all as specified and as directed.

M & L repair of bore earthing not less than 250 mm dia 16 feet deep filled with black soil up to 7 feet from bottom complete with galvanized iron pipe 40 mm bore