Development of Mangrove Park at Mogharpada within TMC Limit

Amount

Sr No..1Providing and laying cast in situ / Ready Mix Cement Concrete M-40 for bored piles each of load capacity and as per design and of 800 mm diameter. or as directed placed through steel shells sunk to the required depth through all strata except rock excluding provision of reinforcement as per detailed drawings and design approved by the Engineer-in- charge includingplacing with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) by tremie arrangements, compaction of concrete including chipping and dressing and withdrawal of shell etc. complete. (Excluding steel reinforcement)

Sr No..2Chiseling through pile shells in hard strata like boulders, soft and hard rocks Beyond 900 mm and upto and inclusive of 1050 mm dia. including removing and stacking the loose materials etc. complete and disposing of the unserviceable materials outside complete.

Sr No..3Carrying out load test for 1.5 times the proposed safe working load on the pile in driven position above 750 mm and upto 825 mm diameter including construction of test cap, use of accessories and instruments including providing graphs as per I.S. code or Std.Specifications and dismantling the test cap after testing and cleaning the site complete.

Sr No..4Item No159 Carrying out low strain pile integrity test on 900 mm diameter pile including all arrangements for test, equipments/accessories, materials, labour, submission of test report etc but excluding the cost of installation of job pile (installation of pile shall be paid seperately as per releventitems)all complete as per specification and as directed by the engineer-in-charge

Sr No..5Empty boring for 725 to 1050 mm dia. bored R.C.C. cast in situ piles including withdrawal of shell, removal of earth to a distance of 50 metres etc. complete. Spec :(As directed by Engineer in Charge)

Sr No..6Providing bentonite slurry process for various diameter of piles vide Item Nos 1 (i to xxiv) above. Spec : (As directed by Engineer in Charge)

Sr No..7Providing placing and Driving in position 6 millimeter mild steel liner for R.C.C. Piles upto required depth with 12mm thick mild steel cutting edge of 0.50m length at bottom including fabricating cutting the mild steel sheet to required diameter and shape ,welding the joints and driving with the help of required machineries including all materials labours and lifts etc. complete as directed by the Engineer in charge. Spec :(As directed by Engineer in Charge From 3.00 to 9.50 meter deep liner

Sr No..8Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.) By Mechanical Means

Sr No..9Removing sand /muck/ slush /soil bellow low tide level to the specified section from navigation channel as per the area and depth upto 3.00 m from sea bed by mechanicel means with , hyderaulic excavator, etc. and barge for establisment all machinery with all required tools and equipments, boat for conveying excavetd material, including removing the excavated materials with all lift and leads as directed beyond high tide level line of water stacking spreading or disposing,dewatering if required unless otherwise provided else where complete under tidal condition.

Sr No..10Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting etc. complete.

Sr No..11Providing and laying Cast in situ/Ready Mix cement concrete in M20 of trap/ granite/quartzite/gneiss metal for bed blocks, foundation blocks and such other items including bailing out water, Steel centering, formwork, laying/ pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Sr No..12Providing and laying Cast in situ/Ready Mix cement concrete M-40 of trap / granite/quartzite/ gneiss metal for R.C.C. work in foundations like raft, Pile Cap , strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. columns as per detailed designs and drawing or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Sr No..13 Providing structural steel work of rectangular hollow steel section for steel trusses, other similar trussed items like purlin and members with all bracing, gusset plates etc. as per detailed designs and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted/bolted/ welded connections and one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade complete.Including all lead and Lift Charges in Inacessible Area and Include Tidal Condition

Sr No..14Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap/ granite / quartzite/ gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) For Ground Floor (Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..15For 1st Floor

Sr No..16For 4th Floor

Sr No..17For Terrace

Sr No..18Providing and fixing structural Profile decking sheet as per particular specification,with GI sheet, zinc coating not less than 275 GSM as per IS 277 and of yield strength 500 Mpa of approved make with specified Base Metal Thickness. The profile shall be structural decking profile having ribs & pitch as per the drawing referred with the embossments (shear groove) on top and side of the ribs for better composite action. The decking sheet shall be fabricated to required form as per the slab design and fixed with Galvanised Iron fasteners, self drilling screws, shear studs as per IS 1367, connectors etc. complete as per design, drawing and direction of Engineer-in- Charge. (Refer typical drwg). Plan area of the sheeting shall be measured and paid for.Structural steel frame work, reinforcement steel and concrete shall be paid seperately.With Base Metal Thickness (BMT) (excluding Zinc coatthickness) 1.20 mm thick Profile decking sheet (Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..19Providing and fixing 900mm high S.S.304 Grade Stainless steel railing with 40mm diameter and 1.5mm thick at top, 40mm diameter and 1.5mm thick vertical supports spaced at 1.5m center to center and 8mm thick toughened glass including fabricating ,fixtures, errecting , necessary welding , grinding , finishing, buffing to stainless steel pipe etc. complete (Including All Lead , Lift and Other Charges as per Site Condition)Ground Floor

Sr No..20For 1st Floor

Sr No..21For 2nd Floor

Sr No..22For 3rd Floor

Sr No..23For 4th Floor

Sr No..24Providing and laying Cast in situ/Ready Mix cement concrete in M-30 of trap/ granite/ quartzite/ gneiss metal for R.C.C. pardi of required thickness including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) (Including All Lead , Lift and Other Charges as per Site Condition) Ground Floor

Sr No..25For 1st Floor

Sr No..26For 2nd Floor

Sr No..27For 3rd Floor

Sr No..28For 4th Floor

Sr No..29For Terrace

Sr No..30Providing and laying Cast in situ/Ready Mix cement concrete in M-30 of trap / quartzite /granite /gneiss metal for R.C.C. Waist slab, and steps of staircases as per detailed design and drawings or as directed including steel centering, plywood/ steel formwork, steel props, laying/pumping, compaction, finishing uneven and honeycombed surface with C.M. 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing etc. complete. (Excluding einforcement, including cover block).(Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc.) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) (Including All Lead , Lift and Other Charges as per Site Condition) Ground Floor

Sr No..31For 1st Floor

Sr No..32For 2nd Floor

Sr No..33For 3rd Floor

Sr No..34For 4th Floor

Sr No..35Providing and fixing in position HCRM / CRS (Corrosion Resistant Steel) bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. (Including All Lead , Lift and Other Charges as per Site Condition) Ground Floor

Sr No..36For 1st Floor

Sr No..37For 2nd Floor

Sr No..38For 3rd Floor

Sr No..39For 4th Floor

Sr No..40For Terrace

Sr No..41Providing and constructing non load bearing wall with 100mm Horizontally perforated clay hollow blocks of approved make with compressive strength not less than 35Kilogram/Sq.cm, U value of 47.0 W/m2k, Water Absorption of 15%, with cement mortar 1:6 with blocks of size 400mm x 100mm x 200mm (12.5 bricks per Square Metre. excluding mortar joint thickness) At every 5th course level, Concrete band of 100mm thick with 1:3:6 Mix Concrete along with Nominal Reinforcement to be provided. The rate inclusive of cost of materials, labour charges, scaffolding, curing at all height, complete as per specifications & directions of Engineer-in Charge. Cost shall be inclusive of filling the Blocks with Cement mortar at exposed junctions and filling with concrete using 12mm down size aggregates at Window and door Jambs for fixing hold fast, anchors etc. (Including All Lead , Lift and Other Charges as per Site Condition) Ground Floor

Sr No..42For 1st Floor

Sr No..43For 2nd Floor

Sr No..44For 3rd Floor

Sr No..45For 4th Floor

Sr No..46Bamboowood 10mm thick Wall Cladding including Threshold & T-mold - Providing & fixing in position Phenol bonded Bamboowood wall cladding at all height with planks of sizes 10mm thick, 1900mm length (minimum) and 135mm wide approved colour, texture and finish, having Performance Appraisal Certificate (PAC) issued by Building materials & Technology Promotion Council (BMTPC). with necessary profiled edges fixed with BR nails to frame work made of second class teak wood of size 50 x 50mm in centre and ends of each tile. The bamboowood cladding shall be laid over teak wood frame and hold in place by 50mm thick teak wood placed in centre of two teak wood and backlayment and covered with 1.00mm thick expanded poly ethylene foam of density 25Kilogram/cum in two layers first layer on wall surface before fixing wooden frame and second layer on frame under cladding. The Bamboowood planks shall have minimum density of 1000 Kilogram/cum & minimum Hardness 1000 Kilogramf. with Eco friendly UV coating, all complete as per direction of Engineer in-charge. (Including All Lead , Lift and Other Charges as per Site Condition) Ground Floor

Sr No..47For For 4th Floor

Sr No..48Providing & Fixing Exterior Grade Fibre Reinforced Polymer (FRP) composite panel cladding system of 4mm thick FRP sheet for FINS 200 x 50 with appropriate skin thickness & 38x38x1.5mm framework, based on drawings, including design analysis, preparation of detailed shop drawings, and fabricating, supplying, and delivering material at the site. The work involves assembling and installing/fixing the FRP fins in position with required stainless steel brackets, bolts, nuts, and mild steel fixings as necessary. All cutting, drilling, and other operations required for proper installation shall be executed as per the approved design and drawings. The FRP fins shall be sourced from reputed brands such as Suvarna Fibrotech Pvt. Ltd,Crystal Fibrotech,Prolong Composites India Pvt. Ltd known for producing high-quality, durable, and UV- resistant FRP products. The rate shall also include all necessary scaffolding, working platforms, and hoisting arrangements for safe and efficient installation. The FRP fins shall be lightweight yet strong, corrosion-resistant, UV-stable, and designed to withstand outdoor environmental conditions, ensuring durability and long-term performance.directed by the Design Consultant & Engineer-in- charge, complete in all respects (Including All Lead , Lift and Other Charges as per Site Condition) .(Including 5 Years of Maintenance)

Sr No..49Providing & Fixing Exterior Grade Aluminium composite panel (ACP) cladding system of 4mm thick ACP sheet for FINS 200 x 50 with 0.5mm skin thickness & 38x38x1.5mm framework, based on drawings, including design analysis, preparation of detailed shop drawings, and fabricating, supplying, and delivering material at the site. The work includes assembling and installing/fixing the ACP fins in position with required stainless steel brackets, bolts, nuts, and mild steel fixings as necessary. All cutting, drilling, and other operations required for proper installation shall be carried out as per the approved design and drawings. The ACP fins shall be sourced from reputed brands in India such as Alumine Fabricators India Pvt. Ltd or VNV Facades, known for their high-quality, durable, and weather- resistant ACP products. The rate shall also include all necessary scaffolding, working platforms, and hoisting arrangements for safe and efficient installation, ensuring a long- lasting and aesthetically pleasing result.directed by the Design Consultant & Engineer-in-charge, complete in all respects (Including All Lead , Lift and Other Charges as per Site Condition).(Including 5 Years of Maintenance)

Sr No..50Providing and fixing glazing panels & doors using 12mm thk toughen clear glass (confirming to ASTM Standards C-1048) supported byc-channel (embedded in the floor) at the bottom & side edge and wall connecting profile at the top edge,stainless steel articulated countersunk bolts threaded bolts,chemical fasterners,etc., glass panel size as per design and drawing including applying colourless sealant of joint incl. required edge polish, making glazing water tight etc. Destructive node joint test reports to be submitted for establishing the safety factor, including operating hardware, SS patch fittings, fabricated long length satin finish SS 304 handles,patchlock, floor springs etc., complete as directed by the architect for frameless patch doors,single or twin leaf shutters with fixed panel on top. Hardware-Droma BTS 80 Floor Spring. (Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..51Providing and fixing in position Top/side hung window of extruded modular and anodised aluminum sections of approved make and of size 38.10 mm x 25.40 mm x 1.44 mm thk (wt. 0.471 kg/Rm) for outer rectangular tube, 40 mm x 31.5 mm x 1.5 mm (wt. 0.549 kg/Rm) for outer frame, 40 mm x 31.50 mm x 1.50 mm thk (wt. 0.502 kg/Rm) for central mullion, 40 mm x 31.50 mm x 1.50 mm thk (wt. 0.549 kg/Rm) for shutter and 16.50 mm x 14.50 mm x 1.20 mm thk (wt. 0.157 kg/Rm) for glazing clip with 5 mm thick plain / frosted / tinted glass fixed in shutter including neoprene gasket, fixtures, fastenings and accessories like hinges, locking arrangement etc. complete as directed by Engineer In Charge. (Note: anodic film must not be less than 15 microns i.e. AC-15 as per IS, the anodizing must be scaleted by keeping the anodized section in boiling de-anodized water for a period of one hour) (Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..52SITC OF Hermetically Sealing type of Manual Sliding /Swing Door having thickness of 40-48mm of size 1500 X2100 mm Single / dual leaf with PUF core sandwiched between Antimicrobial High Pressure laminates (HPL), with viewing window of size 300 X 300 mm. The door leafs hung on extruded heavy duty aluminium alloy extrusion Doorframe for single side swing Doors, Sliding Door leafs runs on (nylon wheels) within an extruded heavy duty aluminium alloy extrusion track / frames, for smooth effortless sliding with the help of handle. (Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..53SITC OF Microprocessor based Electronic Automation (Operator ) for Manual Door for controlling the direction of movements, the acceleration and speed of the door, with a low noise level pulse generator motor. It includes a photocell for users safety. (For sliding door (Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..54Door Type D5Providing & fixing in position fully glazed 50mm thick Door. Vertical styles & top rail made of 100x50mm thick approved quality seasoned T.W.& bottom rail made of 150x50mm thk.approved quality seasoned T.W. finish with 4 mm veneer on both sides with & glass panels of 8mm thick clear float glass of approved make fix with For 1st class BTC 25x12 mouldings. Rate is inclusive of s.s.fixtures & fittings, such as handles on both sides, tower bolts, locking arrangement, concealed type door closure, door stopper of make ( ozone,Hettich,Hafle ), as per architect's detailed drg. and design complete.Door size - 1000x2100. =GL-D (Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..55Full Height Partitions in Glass finish - Providing and Fixing 80mm to 85mm thick Full height Double Skin partition up to 3 mtr height with All visible sections in Anodized / Powdercoated finish. Made up of Frames and Tiles. Frame construction In combinaton of Aluminium Rails and Bottom ,Center and Top members, Connected with 2 way Round Shape Post , 3way Post , 4 way Post made up of Aluminium Extruded and Tiles in 5mm thk. Non Toughened Glass on both side. With all the Joints in the partitions covered with PVC extrusions to provide better sound Proofing. Tiles to be separated 55mm from each other to provide adequate space for drawing cables for electric, data and telephone with proper facility for fixing electrical and data switch plates. as per design and drawing. (Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..56Providing & fixing FULL HEIGHT BOTH SIDE LAMINATED PARTITION at required location having height more than 2.8 meter & minimum 77 mm thick made by using 50 x 50 mm (finished size) approved quality seasoned TW section framing at 600 mm center to center,covered with 12 mm marine ply generally confirming to I.S.303 / I.S.710-1980 on both sides.The partitions shall be finished with 1.5 mm thk.approved quality laminate matt/suede/fine line finished lamination pattern with grooves on both sides with necessary lipping (BTC) moulding. Antitermite treatment to plywood and woodwork, door frame including all leads & lifts etc complete as per Architect's Drawing and instructions of Engineer In Charge.

Sr No..57Supply and installation of cubicles of width and depth as per Athena Lite- SS Series Cubicles- Std Sizes (W x D x H): 900 mm x 1550 mm x 2105 mm, (Height is including 100 mm gap from bottom, Door Width- 600 mm specifications/ site drawings). Cubicle height to be 2105 mm. Made from solid grade compact high pressure laminate as per IS:2046 and EN-438 manufactured under high specific pressure > 5 MPa and temperature >120°C, All doors will be of single colour and made of 12 mm thick Merino HPL compact panel. The doors will have chamfered edges. Each door will be supported by 3 stainless steel made hinges affixed to the pilasters. Size of panels to be as per drawing. HARDWARE & ACCESSORIES are H shaped (Top) head frame structure made of extruded Aluminium grade 6063 T5-50 micron epoxy powder coated for surface protection, Size to be 125x70x5T. Corner joinery section, Size to be 40x16.5x1.8T. U-Channel Wall joinery section,Size to be 22x16x1.6T. Door stopper section, Size to be 21x12.5x1.6T. Spring loaded Butt Hinges made from Stainless steel grade 304. Surface finish to be matt type. Covers to be lacor coated.etc complete. (Including All Lead , Lift and Other Charges as per Site Condition) Ground Floor

Sr No..58For 4th Floor

Sr No..59Vertical Garden: Providing and installation 1) M.S. Fabrication for green wall as per directed layout. 2) Providing Fiber pots as per specifications. 3)Providing material for planting such as cocopit ,vermicmopost etc mixed well in proportion as directed. 4) Providing and installation standered drp irrigation systemfully functional as per directed , including mist spray systeam .providing and planting of plant varieties as directed and maintaining till wll established by watering through proper functioning wzter system , stirring replacing casualities 6) MS structure by %-coat Jotun or similar anti corrosive marine grade paint ssysteam etc complete as per market lowest rate (Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..60Providing and applying water proofing treatment using acrylic polymer modified cement based water proofing coating with fibre glass mesh mixing at the rate of powder to liquid (2:1) by weight covering 9 to 10 Square Metre /Kilogram with two coat using approved chemicals for masonry and concrete surface by brush covering 7 years guarantee on Stamp Papers etc. complete. (Including All Lead , Lift and Other Charges as per Site Condition) Ground Floor

Sr No..61For 4th Floor

Sr No..62For Terrace Floor

Sr No..63Providing internal cement plaster 12mm thick in single coat in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. (Including All Lead , Lift and Other Charges as per Site Condition) complete.Ground Floor

Sr No..64For 1st Floor

Sr No..65For 2nd Floor

Sr No..66For 3rd Floor

Sr No..67For 4th Floor

Sr No..68Providing and applying 2 coats of 100% Pure acrylic low VOC and APEO & HCHO free water based paint of approved colour that belongs to class 1 flame spread resistance of approved make Paint should provide durable and long lasting silk finish with a high crack tolerance of upto 1mm. Paint should have an oustanding washability with high resistance to wide range of bacteria and fungus. Paint has to be applied on smooth and uniform surface prepared by an acrylic copolymer low VOC & Odour putty. This surface should be primed with water based low VOC Primer. The work activity should cover all aspects of applying paints from surface preparation as directed by Engineer in charge. (Including All Lead , Lift and Other Charges as per Site Condition) Ground Floor

Sr No..69For 1st Floor

Sr No..70For 2nd Floor

Sr No..71For 3rd Floor

Sr No..72For 4th Floor

Sr No..73Providing and fixing frame work of anodised aluminium sections for suspended false ceiling consisting of aluminium T 50 mm x 40 mm weighing 0.39 Kilogram/m. at 60 cms c/c and fixed with ( 15 x 15 mm) flanges weighing 0.119 Kilogram/m suspended on 6 mm dia. mild steel rod weighing 0.22 Kilogram/m fixed on wall and beams including rounding of the edges with aluminium T of 50 mm x 40 mm weighing 0.39 Kilogram/m etc. including all labour etc. complete. (Including All Lead , Lift and Other Charges as per Site Condition) Ground Floor

Sr No..74For 1st Floor

Sr No..75For 2nd Floor

Sr No..76For 3rd Floor

Sr No..77For 4th Floor

Sr No..78Providing and fixing false ceiling of 10 to 12 mm thick decorative boards of fibrous plaster of paris including scaffolding if necessary all architectural work like mouldings, cornices, coves, domes, cups as per detailed drawings and three coats of spray painting to boards etc. complete. (excluding frame work, runners and mild steel suspenders). (Including All Lead , Lift and Other Charges as per Site Condition) Ground Floor

Sr No..79For 1st Floor

Sr No..80For 2nd Floor

Sr No..81For 3rd Floor

Sr No..82For 4th Floor

Sr No..83Supply, fixing and installation of 4mm thick Aluminium Composite Panel (ACP) of approved colour for external cladding in Wooden finish colour or as per approve colour and shade by Engineer in CHarge, including all necessary Framework, support and complete weather sealing as per architectural drawing. The Aluminium Composite Panel (ACP) should be made out of thermoplastic core of low-density polyethylene LDPE (100% virgin mix), sandwiched between two aluminium sheets of ALLOY GRADE- 5000 series, each not less than 0.50 mm thick, total thickness of aluminium composite panels not to be less than 4 mm, the exposed surface thereof shall have Stove lacquered finishing coat not less than (26 + - 2) micron (containing minimum 70% kynar 500 based PVDF) of colour and shade as per architectural design. The inside surface (facing the building exterior surface)shall have polyster based powder coating not less than 25 Micron with protective peel-off foil on the exterior face (peel off film will in no case leave any adhesive mark over the composite panel surface after it is peeled off). The supporting framework shall be made out of 50 mm X25mm X 3mm thick Aluminium section to be spaced horizontally and vertically for fixing of panel of size 900 mm X 1200 mm and fixed to the building structure as per design through 50mm X50mm X5 mm MS angle clamps prefixed to masonry or slab, columns with Hilti make anchor fastener screws. The fixing of panel to be done with the help of VHB tapes and screws and all the sealing of joints to be done with weather sealent Silicon as directed by Engineer-in-charge. (Prior permission of S.E. is necessary before inclusion of this item in estimate) (Including All Lead , Lift and Other Charges as per Site Condition)Ground Floor

Sr No..84For 1st Floor

Sr No..85For 4th Floor

Sr No..86ACOUSTICAL WOODWOOL FALSE CEILING: Providing & fixing of 100% Natural Material- Magnesite (Hygroscopic & biologically sound binding agent) bonded woodwool Heradesign planks of 600Mm*1200Mm *25Mm thickness made out of wood wool fiber of width 1Mm Fiber thickness mixed with Natural water & Magnesite (No-Cement) with open & smooth surface texture, Weight of panel to be 11.3 Kg/m2. A Completely harmless Environment & Human Friendly & also a disposable or recyclable Material & can last for more than 80 Years in building interiors As it has long lifespan & suitable for Indoor conditions with relative air humidity of upto 90%. Magnesite protects the wood cells against ageing & fungal attack. To achieve upto NRC=1.00 it should be a clear gap of 200Mm from wall slab along with the backing of Mineral wool of 50mm thick with 64 kg/m3 density. Ecologically Sound Material with high mechanical strength with Crash test of 90Km/H with Ball Impact Test DIN18032 & EN13964 with flying colors & A sustainable material (PEFC & FSC Certified) along with EPD Certified Acc. to EN ISO 14025 (AUB-Environmental Product declaration). Manufacturing tolerance for nominal size: Length, Width & Thickness ± 1 mm, & In a Standard Climate of 23° C and 50% rel. humidity. FIXING & SUBSTRUCTURE: Impact Resistant According to DIN-18023 or EN13964 to be Fixed on CD Sections Profile framework with Screw 9Pc/Panel & Centre Distance Support of 300Mm & Centre distance of Cross Profile would be at 600Mm & Main Profile at 900Mm CD Profile is made out of GI( Sections Profile 60/27/0.6Mm-0.6MmThick x 60Mm Width x 0.27Mm height). The Main Profile is in the length of 3000mm & to form a section of 600mm x 1200mm. The CD Profile is to be suspended from soffit with the help of nonius hanger at a center distance of 900mm. UD Profile 28/27/0.6mm to be fixed on wall at the perimeter of the wall. If the main CD profile needs to extended, it needs to be connected with CD profile connector 60/27. The CD profiles to be connected to each other at the intersection by CD cross connector. Heradesign Superfine panels to be fixed to the ceiling with a minimum of 200mm void or gap with Galvanized screws of length 50Mm & Dia 4.5Mm with a backing of Mineral Wool of density 64kg/m3 density (50mm thick). Colour pf Panels : NATURAL BEIGE, Can be Painted to the desired colour (Any- RAL, NCS or StoColor Shades) using water based color by Spray method prior to installation. FIRE CLASS as per EN 13501-1:B –s1, d0. Test Certificates to be submitted. (Including All Lead , Lift and Other Charges as per Site Condition) Fourth Floor

Sr No..87Providing and laying machine cut machine polished machine cut Kota stone slabs 20 to 25 mm thick for treads and risers of steps and staircases, with rounded nosing for the treads on a bed of 1:4 cement mortar including cement float, filling joints with neat cement slurry, curing, polishing and cleaning etc. complete (Including All Lead , Lift and Other Charges as per Site Condition) Ground Floor

Sr No..88For 1st Floor

Sr No..89For 2nd Floor

Sr No..90For 3rd Floor

Sr No..91For 4th Floor

Sr No..92Providing and laying in position flooring of telephone black / Amba White / Cat bary brown / Ruby red / Ocean Brown granite stone of approved shade and size 18 mm to 20 mm thick on bed 1:6 cement mortar including cement floats striking joints, pointing in C.M. 1:3 curing and cleaning etc. complete. (Including All Lead , Lift and Other Charges as per Site Condition) Ground Floor

Sr No..93For 4th Floor

Sr No..94Providing and laying Polished Kota stone flooring With Hand-Cut Polished Kota Stones 25mm to 30mm thick and required width in plain/diamond pattern on bed of 1:6 Cement mortar including cement float, filling joints with neat cement slurry, curing, cleaning and Mirror Polishing etc. complete Note- Water absorption for kota stone should not exceed 0.05%.( Item to be used with prior permission of Superintending Engineer ) (Including All Lead , Lift and Other Charges as per Site Condition) Ground Floor

Sr No..95For 1st Floor

Sr No..96For 2nd Floor

Sr No..97For 3rd Floor

Sr No..98For 4th Floor

Sr No..99Providing leather finished polishing to Kota / Marble / Shahabad / Kadappa Stone slab by continuous grinding in 4 coats of different bits to receive rough and matty finish including buffing process before laying and fixing of stone as per drawing and design, including cleaning, washing and finishing etc. complete. (Including All Lead , Lift and Other Charges as per Site Condition) Ground Floor

Sr No..100For 1st Floor

Sr No..101For 2nd Floor

Sr No..102For 3rd Floor

Sr No..103For 4th Floor

Sr No..104Providing and laying 800 x 800 x 9 to 10 mm thk. vitrified tiles as specified below conforming to I.S.15622-2006 with water absorbtion less than 0.08% for flooring of an approved, quality, make, pattern and size for flooring including cement mortar bedding of 25 mm thick in 1:4 proportion, cutting, leveling, jointing, filling the joints by neat cement slurry or approved colour grout, curing, finishing etc complete as directed by Engineer In Charge. (Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..105Providing and laying at site 8mm thick laminated flooring having an inbuilt 1mm soundbloc CS backing - class of use 33/23, wear resistance AC-5, impact resistance - IC 3, (as per EN 13329), top surface having a MLC (Multi Layer Composite) high pressure laminate, top surface treated with (Aluminium Oxide) surface guard (tm) plus on top of high density fibreboard substrate (density 910 kg/m3) specially developed core; of plank size 1994mm x 194mm having smart lock tounge and groove joints to secure long lasting joint. The edge of tounge and groove of planks duly impregneted with paraffin. The approved decor planks to be placed on underly - 0.2mm thick alkali resistant polythylene sheet (Density 935 Kg/m3) to resist any moisture movement from the sub floor and secure floating floor installation. Pergo original conforms to EN 13329, ASTM C 1028, DIN 52185, DIN 54345, EN 717-2, DIN 4102.oring (Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..106Providing and constructing granite kitchen platform with fixing of stainless steel sink 600 mm x 450 mm size as per detailed drawing including vertical both side polished kadappah stone 25 to 30 mm thick supports with kadappah top 35 to 40 mm thick and polished granite 16 to 20 mm top with side strips of granite at front and both sides of platform raised with two vertical granite supports 15 cm height and top granite of 75 x 40 cm including cutting, opening for sink of required size in kadappah as well as granite etc. complete. (Platform top size 5.00 m x 0.60 m and height is 0.75 m) (Including All Lead , Lift and Other Charges as per Site Condition) For 4th Floor

Sr No..107Providing 25 mm to 30 mm thick partition of polished black kadappa stone slab of approved quality including giving required size and shape etc. Fixing in cement mortar 1:3 curing and cement etc. complete. a) One side polish (Including All Lead , Lift and Other Charges as per Site Condition) Ground Floor

Sr No..108For 4th Floor

Sr No..109Bamboowood 20mm thick Decking Outdoor Flooring Tile Providing & fixing in position Phenol bonded Epitome Bamboowood deck flooring tiles with planks of sizes 20mm thick, 1900 mm length and 135mm wide ,in approved colour , texture and finish , having performance Appraisal Certificate (PAC) issued by Building Materials& Technology promotion Council (BMTPC)with necessary profiled edges and groove fixed with 40mm ss screws 3 nos in each tile to frame work made of second class seasoned and treated teak wood of size 38x38 mm placed underneath acoss the tile at both ends and in centre fixed with clips holding in position. The Epitome Bamboowood planks shall have minimum density of 1000 Kilogram/cum & minimum hardness 1000 Kilogramf.all complete as per direction of engineer in-charge. (Including All Lead , Lift and Other Charges as per Site Condition) Ground Floor

Sr No..110For 4th Floor

Sr No..111Providing and laying in place 300mm x 300mm x 9.8mm vitrified tactile warning and directional tiles of the approved brand, make and colour inside the buildings at in all corridors and lobbies, level differences etc. as per accessibility standards and as per the installation instructions prescribed by the manufacturer including zarri making wherever required and finishing including grouting the joints with white cement with matching pigments etc. up to the satisfaction of the engineer in charge complete. (Including All Lead , Lift and Other Charges as per Site Condition) Ground Floor

Sr No..112For 1st Floor

Sr No..113For 2nd Floor

Sr No..114For 3rd Floor

Sr No..115Providing and fixing green marble of 18 to 20 mm thick for door frame/ dado/ window boxing etc. On C.M. 1:6 including filling joints with polymer base filler nosing / moulding the sharp edges wherever necessary, curing, etc. complete. (Including All Lead , Lift and Other Charges as per Site Condition) Ground Floor

Sr No..116For 4th Floor

Sr No..117For Terrace Floor

Sr No..118Providing and fixing in position powder coated aluminium louvered windows / ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38 mm x 1.22 mm box type, 5 mm thick sheet glass louvers, of approved quality etc. complete. (Including All Lead , Lift and Other Charges as per Site Condition) Ground Floor

Sr No..119For 4th Floor

Sr No..120Providing and fixing frame with / without ventilator of size as specified with Country non teak wood for doors and windows including chamfering, rounding, rebating, iron holdfast of size 300mm x 40mm x 5mm with oil painting, etc. complete. (Including All Lead , Lift and Other Charges as per Site Condition) Ground Floor

Sr No..121For 1st Floor

Sr No..122For 2nd Floor

Sr No..123For 3rd Floor

Sr No..124For 4th Floor

Sr No..125For Terrace Floor

Sr No..126Providing and fixing Country cut teak wood double or single leaf panelled shutters, 35 mm thick style top and freze rail 95 x 35 thick with lock and bottam rail 195 x 25 mm thick and panels without ventilator as per detailed drawing excluding the door frame, stainless steel fixtures and fastening and finishing the wood work with oil painting 3 coats complete (Including All Lead , Lift and Other Charges as per Site Condition) Ground Floor

Sr No..127For 4th Floor

Sr No..128Providing and fixing fiber glass reinforced polyster door shutter 35 mm thick as per IS 14856 (2000) (Reaffirmed 2006) without ventilator including chromium plated fixtures and fastening with chromium plated handles on both sides, etc complete. (Including All Lead , Lift and Other Charges as per Site Condition) Ground Floor

Sr No..129For 1st Floor

Sr No..130For 2nd Floor

Sr No..131For 3rd Floor

Sr No..132For 4th Floor

Sr No..133For Terrace Floor

Sr No..134Providing and fixing in position U.P.V.C.(Unplasticized Poly Vinyl Chloride) having multi- chambered outer frame section (73 x 50)mm with an outer wall thickness of 2mm & steel reinforcement, multi-chambered slider frame (73x 60) mm with steel reinforcement, multi- chambered slider sash (46x 82) mm with steel reinforcement designed to give optimum strength, 5 mm thick toughened double glass with 12 mm spacer of good quality including alluminium track, Inter-locking profile, coextruded beadings, EPDM gaskets,silicon sealent,sliding handle, fixtures and fastenings (couplings, hinges) including with all required screws and nuts with all necessary U.P.V.C. sections as per the detailed drawing and as directed by Engineer-In-Charge etc. complete. (Including All Lead , Lift and Other Charges as per Site Condition) Ground Floor

Sr No..135For 4th Floor

Sr No..136Providing & fixing factory-made Single leaf 2 hour fire rated door as per IS 3614 Part 2 & BS 476 Part 20 & 22, tested to UL 10 C and conforming to NFPA 80 , tested at NTL /CBRI/ARAI of Plain Steel finish type with a.) Frame of size 143x58 mm and thickness of 1.6 mm thick skin pass galvanized iron sheet (Conform to IS 277 ) formed to single or double rebate profile b.) Shutter of 46 mm thickness and constructed from 1.2 mm thick skin pas galvanized iron sheet (Conform to IS 277) infill Rockwool / Mineral wool/ Honey comb craft paper c.) Vision glass of 5mm thick clear/wired glass Circular or Rectangular d.) Finish : Primed with zinc phosphate stoving primer and finished with Polyurethane aliphatic grade or epoxy paint as required of thickness 60 micron e.) Accessories : Min 8 Anchor fastener of HILTI make, min 3 SS Ball Bearing Butt Hinges, Mortise sash lock with lever handle, Mortise dead bolt , Mortise latch , Door closer and Flush bolts complete. (Including All Lead , Lift and Other Charges as per Site Condition)Ground Floor

Sr No..137For 1st Floor

Sr No..138For 2nd Floor

Sr No..139For 3rd Floor

Sr No..140For 4th Floor

Sr No..141For Terrace

Sr No..142Executive Table @ 2250Lx2100Dx750HT including Low Height Credestal @ 1200Lx450Dx650HT Providing & Fixing of Table @ 2250Lx2100Dx750HT TOP & GABLE END to be made of Membrane finish with soft water fall edges & curved panel & Decorated Anodized section MODESTY PANEL to be made of 18 mm thick Prelaminated particle board with PVC edge band. INCLUDING CREDESTAL @ 1200L X 450D X 650H :- To be made out of Membrane Finish ( 2 Openable Shutter & 3 Drawer Pedestal in between ) as per drawing. (Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..143Conference Table @ 3600Lx1400Dx750HT Providing & Fixing of Main Table @ 3600Lx1400Dx750HT - made up of 18+18mm Thick MDF top with PVC Membrane finish and waterfall edge profile. Aluminium Anodizied finish beeding of 4mm thich is running all over the table top edge. Gable ends is Aerofoiled Shape with front edges in PVC Membrane finish and rest in Prelaminated MDF with batton structure. Gable ends should be hollow from inside for the provision of passing electrical and Data wiring. , MODESTY PANEL:- to be made of 18 mm thick Prelaminated particle board with PVC edge band Access Flap:- For Wire manager 2 Nos. (Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..144Free Standing Table @ 1500Lx600Dx750HT Providing and fixing Table of Size 1500 x 600 x 750 mm. Top: made from 25 mm Prelaminated Particle board. All edges are covered by 2 mm. Thk. PVC edge bands glued by hot melt glue applied by auto edge banding machine. Legs : C Shape made from CRCA Sheet with Powder Coat finish. Modesty panel : Made from 18mm both side prelaminated particle boards.All edges are covered by 0.8mm PVC edge bands glued by hot melt glue applied by auto edge banding machine.KEYBOARD TRAY ( WITHOUT MOUSE TRAY ) :- Metal Powder Coated - Black Color, CPU TROLLEY :- Metal Powder Coated - Black Color, 3 DRAWER PEDESTAL UNIT having overall size 392L x 450D x 680Ht. mm. with central lock and key. Drawers and body are complete metal with powder coat finish, facia in 18 mm prelaminated particle board, (Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..145Providing & Fixing Curviliner Workstation @ 1500/1500Lx600/600Dx750HT Providing & Fixing Curviliner Workstation @ 1500/1500Lx600/600Dx750HT, Curvilinear Table Top @ 1500/1500Lx600/600D :- TOP to be made of 25 mm thick Prelaminated particle board with PVC edge band, GABLE END to be made of 25 mm thick Prelaminated particle board with PVC edge band, KEYBOARD TRAY ( WITHOUT MOUSE TRAY ) :- Metal Powder Coated - Black Color, CPU TROLLEY :- Metal Powder Coated - Black Color, along with 3 DRAWER PEDESTAL UNIT having overall size 392L x 450D x 680Ht. mm. with central lock and key. 3 Drawers and body are complete metal with powder coat finish, facia in 18 mm prelaminated particle board, (Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..146Providing & Arrangemnt of High Back, Synchronized Mechanism with Multiple Locking, Adjustable Armrest, Gaslift for Seat height adjustment, Standard 5-prong P/Nylon Base with Leatherite Upholstery (Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..147Providing & Arrangemnt of MId Back, Normal Syncro Mechanism , Fixed Armrest , Gaslift for Seat height adjustment, Standard 5-prong/Nylon Base with Leather Upholstery (Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..148Providing & Arrangemnt of Mid Back, ECO CTS Mechanism , Fixed Armrest , Gaslift for Seat height adjustment, Standard 5-prong P/Nylon Base with Fabric Upholstery (Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..149Sofa Set 3+1+1 Providing & fixing Sofa Set 3+1+1 Brown and Cream leather DIMENSION Length: 182.5 (cms) Breadth (cms): 100 (cms)Height (cms): 100 (cms) Weight (Kilograms): 66 (Kilogram) Seating Capacity: Five Seat (Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..150Providing and Fixing Rollar Blinds AMI Make or approved make & shade of 38mm round Aluminium channel with Blackout fabric & telting with chain (Ball) system with all necessary fixtures and fitting etc. complete. (Sample to be (Including All Lead , Lift and Other Charges as per Site Condition) final by Engineer In-charge prior execution of work)

Sr No..151Providing and Fixing Vertical Blinds of approved Make and shade of 100mm regular fabric with powder coated aluminium channel with telting PVC chain & bottom weight plate with all necessary fixtures and fitting etc. complete. (Sample to be final by Engineer In-charge prior execution of work) (Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..152Providing and fixing sheet glass of 24 oz. for all size including putty etc. complete (Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..153Providing,aupplying,fabricating and fixing panel of aluminium composite panel cladding in approved shape made out of 4 mm thick ACP sheet material consisting of 3mm thick FR grade mineral core following NBC part IV Fire and life safety (having 2 hours fire resistance in accordance to ASTM E119-12 and BS476 part 6 and 7 class O) sandwitched between two aluminium sheets (each 0.5 mm thick of AA 5005/AA3105 grade) The aluminium composite panel cladding sheet shall be coil coated with kynar 500 based PVDF/Lumiflon based fluropolymer resin (having 70:30 ratio of PVDF and acrylic) coating of approved colour and sg=hade on top face and polymer (service) coating of bottom face as specified using stainless steel screws,nuts,bolts,washers,cleats,weather silicon sealent,backer rods etc .overall weight of the ACP shall not be less than 7.5 Kilogram/ One Square Metre) (Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..15412 Seater Reading Table for Library @ 3600Lx1200Dx750HT Providing and Fixing 12 Seater Reading Table for Liberary @ 3600Lx1200Dx750HT Top: made from 25 mm Prelaminated Particle board. All edges are covered by 2 mm. Thk. PVC edge bands glued by hot melt glue applied by auto edge banding machine. Gable Ends : made from 25 mm Prelaminated Particle board. All edges are covered by 2 mm. Thk. PVC edge bands glued by hot melt glue applied by auto edge banding machine. Modesty panel : Made from 18mm both side prelaminated particle boards.All edges are covered by 0.8mm PVC edge bands glued by hot melt glue applied by auto edge banding machine. (Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..155Low Height Openable Storage @ 900Lx450x750HT Providing and fixing Openable Steel Storage of 900 x 450 x 750Ht, with 2 adjustable shelves, Complete body & shutter made in 0.8 mm thick & Top in 2 mm thick CRCA, 2 Shutter to be mounted with the help of cup hinges, and 4 adjustable levelers, enitre storage in powder coated finish with 60 to 80 microns. with 25 mm. thk additional Top on top of storage as as per drawing (Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..156Medium Height Steel Storage @ 750Lx450Dx1200HT Providing and fixing Openable Steel Storage of 750 x 450 x 1200Ht, with 2 adjustable shelves, Complete body & shutter made in 0.8 mm thick & Top in 2 mm thick CRCA, 2 Shutter to be mounted with the help of cup hinges, and 4 adjustable levelers, enitre storage in powder coated finish with 60 to 80 microns. with 25 mm. thk. as per drawing. (Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..157Full Height Steel Storage @ 750Lx450Dx2100HT Providing and fixing Openable Steel Storage of 750 x 450 x 2100Ht, with 4 adjustable shelves, Complete body & shutter made in 0.8 mm thick & Top in 2 mm thick CRCA, 4 Shutter to be mounted with the help of cup hinges, and 4 adjustable levelers, enitre storage in powder coated finish with 60 to 80 microns as as per drawing. (Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..158Book Case with Glass Shutter @ 825Lx300Dx1650HT Providing & Fixing of Book Case with Glass Shutter @ 825Lx300Dx1650HT:- To be made out of complete body & in 0.7mm thick CRCA & Shutter in 1.2mm thick CRCA with glass pannel in Powder coating finish as per drawing. (Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..159Library Area Table @ 1350Lx750Dx750HT Providing & Fixing of FREE STANDING TABLE @ 1350Lx750Dx 750HT:- TOP to be made of 25 mm thick Prelaminated particle board with PVC edge band, BENT LEG to be CHROME FINISH as per drawing. (Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..160Providing and Fixing Dining table of Overall S.S (IS 6911:1992),grade of steel 304, Thickness of the table is 40 mm Structure top to be Of s.s 18 SWG 304,Grit. Under Structure to be Vertical poles of 50 mm Dia (16 gauge 304 grade) and top and Bottomsupporting frame Structure to be 50 x 50 mm Square tube etc. complete. Glide shall be of Plastic fixed at the under structure to prevent the damage of table top during stacking. Legs shall be of SS and 38 mm dia (16 gauge 304 grades). pipe legs are fixed with under structure and table top etc. complete. (Including All Lead , Lift and Other Charges as per Site Condition)4 SEATER 1200 X 1000 X 750

Sr No..1616 SEATER 1800 X 1000 X 750

Sr No..162Providing and fixing SS (IS 6911:1992) grade of steel 304 Dinning chirs for dining Hall and dining Room area as per the drawing or approved size and shape including all lead lift shifting to work location etc. complete. (Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..163Providing and fixing 50mm diameter water meter with non-return valve including strainer,sockets/ union nut and including water meter box making locking arrangement and lock. [without chamber]

Sr No..164Providing and fixing screw down for 50 mm dia. wheeled stop tap of brass including necessary sockets/ union nut complete.

Sr No..165Providing and fixing 10cm C.I. Nahani Trap including C.I. grating bend and piece of C.I. pipe upto the outside face of the wall complete.

Sr No..166Providing and fixing 15cm x 10cm salt glazed stoneware gully trap in cement concrete 1:4:8 outside the building including cast iron grating in the sink, connecting glazed stoneware pipe, brick masonry chamber with cast iron lid and cast iron grating for the gully trap.

Sr No..167Providing and fixing 450mm x 550mm size superior type Belgium mirror with 16mm dia. nickel plated towel rod etc. complete.

Sr No..168Providing and fixing on walls/ ceiling/ floor 15 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Sr No..169Providing and fixing on walls/ceiling/floor 20 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Sr No..170Providing and fixing on walls/ ceiling/ floor 25 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Sr No..171Providing and fixing on walls/ ceiling/ floor 32 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Sr No..172Providing and fixing on walls /ceiling/ floor 40 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Sr No..173Providing and fixing on walls/ ceiling/ floor 50 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete.

Sr No..174Providing and fixing C.P.Two way BIB cock of approved make continental including necessary sockets/union nut etc. complete.

Sr No..175Providing and fixing P.V.C. Rain water pipes of 110mm outer diameter and having wall thickness of 2.2 to 2.7 mm confirming to I.S. 13592-1992 including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes, inluding fixing the pipe on wall using approved wooden cleats projecting 25mm to 40mm from face of wall a fixing with clips of approved quality and One Number ,filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc. complete.

Sr No..176Providing and fixing ISI 1729/2002 grade 75 mm dia Cast Iron Waste Water Pipe with lugs necessary fittings such as bends, tees, single junction, double junction, slotted vent, offsets on wall or into the ground including filling joints with cement mortar 1:2 proportion fixing on wall by means by galvanised Mild Steel bracket of 30 x 5 mm plate and 8 mm square rod with Galvanised Iron clamp with washer as per design drawing and as directed to keep pipe 50 mm away from wall including necessary scaffolding and painting the exposed faces with one coat of red lead oil paint and two coats of gray oil paint including removing the existing pipe if necessary and conveying and stacking in PWD Chowky or as directed by Engineer-in-Charge.

Sr No..177Providing and fixing white glazed urinal with Pressmatic auto closing valve having flow rate up to 4.0 Litr/Minute of Jaquar/Cera/Hindware /Perryware or equivalent make with P.V.C. waste pipe with fitting arrangement etc.complete as directed by Engineer in charge.( Make shall conform to manufacturer's Green product and shall got approved from the Engineer In Charge.)

Sr No..178Providing and fixing wall hung white wash basin of size 550 x 400 x 195 mm with pillar cock having flow rate up to 6.0 Litr/Minute,C.P.Angular stop cock long thread of Jaquar/Cera/Hindware /Perryware or equivalent make, including SS bottal trap of approved make etc complete as directed by Engineer in charge.( Make shall conform to manufacturer's Green product and shall got approved from the Engineer In Charge.)

Sr No..179C.P.Toilet paper holder jaquar make continental (Cat. No. AQ 7751 )

Sr No..180cPVC pipe 50mm dia.

Sr No..181Ball cock for 25mm dia.

Sr No..182Providing and fixing high-density polyethylene (HDP) container one piece moulded water tank made out of high density polyethylene and built corrugated inclusive of delivery up to destination hoisting and fixing of accessories such as inlet, outlet overflow pipe inclusive of all tanks capacity up to 20000 litres.. 11 RS/LTR X 2000 ltr

Sr No..183Providing and fixing high-density polyethylene (HDPE) container one piece moulded water tank made out of high density polyethylene and built corrugated inclusive of delivery up to destination hoisting and fixing of accessories such as inlet, outlet overflow pipe inclusive of all tanks capacity up to 20000 litres. 8 RS/LTR X 500 ltr

Sr No..184Supplying and erecting non return valve 50mm dia. in position made of gun metal complete.

Sr No..185Supplying, erecting, testing and commissioning of minimum three & above star rated submersible pumpset of 2.25 kW/3 HP with 415 V, three phase, 50 Hz A.C. supply suitable for 150 mm dia. borewell with 120 to 390 lpm discharge at 55 to 11 m head & discharge & delivery pipe of size-50mm dia. with a necessary H type clamps as per specification no. WP-SMP.

Sr No..186Providing coating of bitumen paint & pipeline corrosion resistant Pypkote tape conforming to IS 10221 Appendix B specification having 4mm thick wrapping for underground 150 mm ring main of fire fighting system. (Pypkote tape comprises of a Tar based Polymeric mix supported on a fabric of high tensile strength Fibreglass).

Sr No..187 Supplying and erecting 50 mm dia gun metal gate valve complete with PN16 pressure rating, as per specification no. FF-VL/GV

Sr No..188Supplying and erecting GI pipe 50mm dia ‘C’ class position with accessories complete as per specification no. CW-PLB/GP.

Sr No..189Supplying and erecting high density polythene pipe 50mm dia. suitable for pressure of 6 kg/cm2 connected to jet/submersible pump with required material complete.

Sr No..190Providing and fixing white european type wall-hung pan, of size 350mm x 355mm x 570 mm concealed flush tank with floor-mounting frame installing kit and drain pipe connection set for wall hung WC, with approved make square control plates including soil pipe, vent pipe upto the outside face of wall, 100mm dia C.I. plug bend inlet pipe all fittings,cutting & making good walls, floors etc. complete.

Sr No..191Providing and Fixing toilet set for differently Abled persons consist of Floor Mounted white vitreous china water Closet including 6 litre capacity white vitreous china flushing Cistern with raised soft-push button, white vitreous china wash basin of size 46 x 36 cm and one no SS 304 hinged rail 76 cms & three no SS 304of (Grab Bar) 60 cms all including cutting and making good the walls and floors wherever required ,seat cover, cistern & wash basin fittings,nuts, bolts and gasket etc complete as per the direction of Engineer-In-charge.

Sr No..192Providing and fixing H.D.P container one piece moulded water tank made out of low density polythyler and built corrugation including of delivery up to destination hoisting and fixing of accessories such as inlet, outlet overflow of all tanks capacity above 1000 to 20,000 litres

Sr No..193Supplying, erecting, testing and commissioning self contained water cooler 230/250 Volts 50 cycles nominal cooling capacity of 150 litres per hour and storage capacity 150 litres with partially stainless steel body as per specification No. AP-WCR/WC

Sr No..194Supplying and erecting ultra violet storage type water purifier (RO+UV+UF) with softener for safe drinking water consisting of UV germicidal tube of 8W capacity choke made of copper wire and two indicator lamps with output of purified water minimum 0.33 litre/min with activated carbon filter and softener operating on 230 V single phase A.C. supply with UV fail & filter change indication system .(for TDS more than 200

Sr No..195Providing and fixing 75 mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete

Sr No..196Providing and fixing 100 mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete.

Sr No..197Providing and laying concrete pipes of I.S.NP. class of 100mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete.

Sr No..198Providing and laying concrete pipes of I.S.NP. class of 300mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete.

Sr No..199Providing and constructing Brick Masonry Inspection Chamber 90cm x 45cm With R.C.C. raft in B.C. soil area including cost of reinforcement, 1:2:4 cement concrete channels half round G.S.W. pipes, Brick Masonry, plastering from inside and airtight with 75 mm thick R.C.C. cover medium duty 140Kilogrametc. complete.

Sr No..200Providing soak pit of size 120cm x 120cm x 120cm including excavating and filling with brick-bats.

Sr No..201Ss Dust Bin Product area:0.76Sqm, Capacity in ltrs: 42.0 ltrs, Product height:0.92m

Sr No..202Trunk Bin Product area:0.38Sqm, Capacity in ltrs: 72.0 ltrs, Product height:0.69m

Sr No..203Providing and laying in trenches 80 mm dia. heavy grade having embossed as ISI Mark galvanised iron pipes of 10.15 Kilogram/metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint , 2 coats complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Sr No..204Providing and laying in trenches 100 mm dia. heavy grade having embossed as ISI Mark galvanised iron pipes of 14.74 Kilogram/metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti- corrosive oil paint , 2 coats complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Sr No..205Providing and fixing screw down for 80 mm. dia. wheeled stop tap of brass including necessary sockets/union nut complete.

Sr No..206Providing and fixing C.P. Angular stop clock with wall flange of approved make continental including necessary sockets/union nut etc. complete.

Sr No..207Providing and fixing C.P. BIB cock with wall flange of approved make including necessary sockets/ union nut etc. complete.

Sr No..208Design Supply and Installation of the Mangroves Trail Walk as per the Approved Design & Drawing Details and Specification of Project Information Memorandum (PIM) attached. Technical Specification : • The mangrove trail should be made in a sustainable method. To avoid harm to the environment/ ecosystem. • The all components should be made in wood/ substitute to wood, but the metal too avoids rusting of the members. • Piles are proposed to be in Jambha (Botincial Name: Xylia xylocarpa) wood which should be designed to take the axial load upto 2000 Kg Per pile. These Piles should be drilled in the mud/ marshy land at 2 Meter c/c and then should be made ready to receive the primary beams on them. • Primary beams should be made in first class teak wood/similar quality substitute. The primary beams do run along the trail, and do support the trail deck which should be designed for live load of 500 kg/sqm. • Providing Cross Bracing for wooden piles as per approved designed and drawing at frequent length and approved by Engineer in charge • Secondary beams are then rested on primary beam perpendicular to the primary beam are to be made of the Nature fibre Composite Material/ similar quality substitute. These secondary beams support keels in made from secondary Nature fibre Composite Material which then support floor finish. • Floor finish should be made to take wear & tear of the people movement, giving appropriate friction in all the seasons and should be long lasting with minimal maintenance. These floor boards can be made in Nature fibre Composite Material). Designing load of 500 kg/sqm should be considered. • Handrails and brackets supporting them should be made in Nature fibre Composite Material / similar quality substitute. • Benches for Rest having 1.5m length and 600mm wide provided at frequent interval specified by the Consultant and Engineer in Charge with brackets supporting them should be made in Nature fibre Composite Material / similar quality substitute. • All of these components should be strictly fixed with nut bolt system made up from high grade stainless steel nut bolts only.

Sr No..209Design Supply, Installation and Commissioning of the Elevated Pause Points having Deck Area with Wooden Roof , Seating Arrangment and Suppoting System in suitable Interval on Mangroves Trail Walk. As per the Design and specification of PIM The Design Material and Specification would be same as per the Mangroves Trail and directed by Engineer In Charge

Sr No..210Dewatering on BHP basis by using water pump including diversion of stream, providing cofferdams, earthern bunds etc. as may be necessary for foundation and other parts of the the works and pumping out water during and after excavation as may be required by using 5.0 to 9.0 BHP pump etc. complete. (prior approval of Superintending Engineer will be necessary) (Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..211Excavation for roadway in earth, soil of all sorts, sand, gravel or soft murum including dressing section to the required grade, camber and side slopes and conveying the excavated materials with all lifts upto a lead of 50m. and spreading for embankment or stacking as directed. (Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..212Removing sand /muck/ slush /soil bellow low tide level to the specified section from navigation channel as per the area and depth upto 3.00 m from sea bed by mechanicel means with , hyderaulic excavator, etc. and barge for establisment all machinery with all required tools and equipments, boat for conveying excavetd material, including removing the excavated materials with all lift and leads as directed beyond high tide level line of water stacking spreading or disposing,dewatering if required unless otherwise provided else where complete under tidal condition. (Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..213 Transporting of excavated/Dismantled materials lead upto 1K.M

Sr No..214Transporting of excavated/Dismantled materials lead upto 7 K.M

Sr No..215Providing earth work in embankment with approved materials obtained from departmental land upto lead of 50m. including all lifts, laying in layers of 20cm. to 30cm. thickness breaking clods, dressing to the required lines, curves, grades & section, watering and compaction with vibratory roller to achieve not less than 97 % of standard proctor density etc. complete ( Material obtained from departmental Land)

Sr No..216Providing earth work in embankment with approved materials obtained from other sources upto lead of 50m. including all lifts, laying in layers of 20cm. to 30cm. thickness breaking clods, dressing to the required lines, curves, grades & section, watering and compaction with vibratory roller with V-Sat attachment to achieve not less than 97 % of standard proctor density etc. complete ( Material obtained from Other sources , All Lead , Lift and Other Charges as per Site Condition)

Sr No..217Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting etc. complete under Tidal Condition .(Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..218Providing and laying CE Marked Needle Punched and Mechanically Bonded Non-Woven Geotextile (TechGeo) indigenously manufactured from high quality polypropylene staple fibres (continuous filament will not be accepted) of Techfab India on the prepared subgrade for separation, drainage & filtration application with necessary overlaps as per drawing etc. complete. (Specification: MORTH Section-700 ) with prior approval of concerned Superitending Engineer. c) TFI TECHGEO PR-30 (With Tidal condition)

Sr No..219Supply and laying of gabion facia with 2m integrated tail as secondary reinforcement for Reinforced soil system as per MoRTH Clause 3100, made of Mechanically Woven Double Twisted Hexagonal Shaped Wire Mesh , Mesh Type 10x12, Zn + 10% Al +Polymer coated Mesh Wire dia. 2.7/3.7mm (ID/OD), mechanically edged / selvedged, with partitions at 1m interval and shall have minimum 10 numbers of mesh openings per meter of mesh perpendicular to twist, tying with lacing wire of dia 2.2/3.2 mm (ID/OD), supplied @ 5% by weight of facia unit , as per detailed specification conforming to codes in vogue all complete as per directions of engineer-in-charge. (Backfilling is excluding)

Sr No..220Supply and installation of Mechanically Woven Double Twisted Hexagonal Shaped Wire Mesh 0.3mthick Gabion(Maccaferri make or equivalent) Boxes ,width 2m, of required sizes, Mesh Type 6x8, Zn+ Al + Polymer coated, Mesh Wire dia. 2.2/3.2mm (ID/OD), mechanically edged / selvedged , with partitions at every 1m interval and shall have minimum 10 numbers of mesh openings per meter of mesh perpendicular to twist, tying with lacing wire, supplied @ 5% by weight of gabion boxes ,as per detailed specification conforming to codes in vogue all complete as per directions of engineer incharge.(With Tidal condition)

Sr No..221Supplying and laying of high strength flexible geogrids (HSFG) as soil reinforcement / basal reinforcement made of high tenacity polyester core with polyethylene coating with Minimum Long Term Design Strength (LTDS) indicated below for 120 years design life at 20 degreeC. The LTDS should be strictly based on reliable test data and performance data available with the manufacturer from accredited independent agency certifying the Reduction Factor (RF) value for their geogrid for design temperature. The geogrid manufacturer should have creep test data from independent accredited laboratory for period over 5 years and should have minimum roll width of 4.5m with core of MS steel tube convenient for handling and lifting work as per detailed specification all complete as per directions of Engineer in charge. (Reference MoRT&H 3100 & IRC 113).High strength geogrid of Long Term Design Strength 59.5 kN/m

Sr No..222Providing & fixing after cutting in proper size & shape bamboo pole of Dentrocalamus stocksii with minimum wall thickness of 10 mm of size 50 mm(+/- 5 mm) diameter (i.e., 50mm dia. in bottom & top dia. should be 35mm & average dia. should not be less than 40mm & taper length should not more than 2.5mm per Rmt), which is well seasoned by freshly cut canes including treatment with preservative inside the bamboo pole &dosing with CCB (Chromium Copper Bromate) using pressure vacuum treatment plant with retention level of minimum 8% and in accordance with IS 9096. These bamboos are used for making beams & columns including bending of bamboos, joining, bunching of bamboos, assembly and its installation as per design using bamboo pegs (45 degree), SS Studs fixed with nuts & bolts (304 grade), GI plates coated with epoxy coating, including transportation & cost of material, antiabrasive fire retardant coating before bunching of bamboos( Two coats before bunching and final coat after complete installation as directed by Engineer in Charge) , necessary scaffolding with all lead, lift, machinery & equipment charges, etc. complete, as directed by the Engineer in charge

Sr No..223Providing and laying Cast in situ/Ready Mix cement concrete in M15 of trap/ granite/quartzite/gneiss metal for steps including steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface, only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.),with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Under Tidal Condition(Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..224Providing and laying Rough Shahabad Stone Flooring 50mm to 60mm thick and of required width in plain/ diamond pattern on a bed of 1:6 C.M. including cement float, striking joints, pointing in cement mortar 1:3 curing and cleaning etc. etc. complete.(Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..225 Accupressure Bed - Providing and laying in position P& F pebbles with colour flooring- of approved quality 25mm to 30mm thick in plain/diamond pattern on a bed of cement mortar 1:6 including cement float, flling joints with neat cement slurry, curing, polishing and cleaning etc. complete. As directed by Engineer-incharge

Sr No..226Providing and laying in position Laterite stone of approved quality 15 cm thick, 380mm ht kerb stone on a bed of cement mortar 1:6 including cement float, filling joints with neat cement slurry, curing, polishing and cleaning etc. complete. As directed by Engineer-incharge

Sr No..227Providing and fixing of retro- reflectorised informatory sign board rectangular/Square in shape having area less than 0.9 One Square Meterr made out of ____mm aluminum sheet bonded with white retro reflective sheeting of Class __ ( Type IV High intensity micro-prismatic grade sheeting-HIP) having pressure sensitive/heat activated adhesive retoreflective specified back ground, border and back side retoreflctive symbols, letters, numerals, arrow as per IRC:67-2012 Table No 8.3, supported with back support frame 25mm x 25mm x 3mm, duly painted on back side with two coats of grey stove enamel paint and supported on one no. mild steel angle iron post 75 mm x 75 mm x 6 mm, 3.5 mt long firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing The angle iron post shall be duly painted with one coat of epoxy primer and two coats of epoxy finish paints having alternate black and white bands of 25 cm width including GI fixures and transportation etc.complete.The nut bolts of board with angle iron post/supporting structure after fixing at site has to be electrically welded. Class B ( Type IV High intensity micro-prismatic grade sheeting-HIP) sheeting shall have 7 years written warranty from the manufacturer and authorised distributor/convertor issued for field performance including the screen printed areas and cut-out sheeting and cut-out durable transparent overlay film and this warranty certificate in original should be submitted to the Engineer in charge by the contractor/supplier.(Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..228Providing and fixing Mandatory / Regulatory sign board of circular shape of size 60 cm. dia. prepared on 16 gauge M.S. sheet including painting with zinc chromate stoving primer and two coats each of white back ground,red border and backside gray stove enamelled, bonded with cut out of Retro reflective sheet Engineering grade, symbol / letters / numerals / border, coated with non pealable crystal clear protective transparent coat retaining 100% relection including one One Number of M.S. Angle iron post of size 50 x 50 x 5 mm of 3.45 m. long inflated at bottom drilled on top in one piece without joint painted with white and black bands of 30 cm. fixing board and post with 2 Nos. high strength G.I. bolts and nuts of size 10 mm dia. and 20 mm long including all taxes, conveying, fixing in ground with cement concrete 1:4:8 block of 60 cm x 60 cm x 75 cm size etc. complete. circular shape of size 60 cm. dia. M.S. sheet with Retro reflective sheet Engineering grade(Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..229Providing and fixing steel pipe delineators of 10 cm. in diameter and total height of 130 cm, provided with 2 strips of white retroreflective sheeting of size 5 cm. x 32.5 cm. each fixed horizontally and 2 strips of red retroreflective sheeting each having size 5 cm. x 32.5 cm. fixed horizontally at top, with M.S. round cap having diameter 11 cm. and wire mesh at top (10 guage thick) and height of wire mesh 15 cm, M.S. hold fast 6 mm thick with 35 cm. in length, fixing the delineators in C.C. 1:4:8 concrete block of size 25 cm. x 25 cm. x 45 cm. with necessary excavation etc. complete.(Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..230Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting etc. complete.(Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..231Providing and laying Cast in situ/Ready Mix cement concrete in M15 of trap/ granite/quartzite/gneiss metal for bed blocks, foundation blocks and such other items including bailing out water, Steel centering, formwork, laying/ pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)(Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..232Providing and laying Rough Shahabad Stone Flooring 50mm to 60mm thick and of required width in plain/ diamond pattern on a bed of 1:6 C.M. including cement float, striking joints, pointing in cement mortar 1:3 curing and cleaning etc. etc. complete.(Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..233Providing and laying Polished Kota stone flooring With Hand-Cut Polished Kota Stones 25mm to 30mm thick and required width in plain/diamond pattern on bed of 1:6 Cement mortar including cement float, filling joints with neat cement slurry, curing, cleaning and Mirror Polishing etc. complete Note- Water absorption for kota stone should not exceed 0.05%.( Item to be used with prior permission of Superintending Engineer )(Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..234Providing leather finished polishing to Kota / Marble / Shahabad / Kadappa Stone slab by continuous grinding in 4 coats of different bits to receive rough and matty finish including buffing process before laying and fixing of stone as per drawing and design, including cleaning, washing and finishing etc. complete.(Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..235Providing and casting in situ or precast tapering R.C.C. M-20 Barrier type Kerb without gutter ( as per IRC 86 1983) embedded 125mm below ground level over M-10 PCC finished neatly with C.M. 1:2, setting the same in C.M. 1:2, including the required excavation in any strata and removing the excavated stuff any where in city and redoing the surface as specified and directed by Engineering In-charge. Using Concrete Batching and Mixing Plant(Including All Lead , Lift and Other Charges as per Site Condition)

Sr No..236Providing and laying wedge shear elemental layer (WSEL) by using rubble stone of size 15 to 20 cm thick in single layer of 230 mm including packing the same with 20 mm to 40 mm thick aggregates ( normal size) and using stone powder of 40 mm to 50 mm thick on surface and watering & compacting by vibratory roller confirming layer thickness of minimum 200 mm and as directed by Engineer - in - charge etc complete.

Sr No..237Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting with vibratory roller to the required density. By Mechanical Means -Grading I (Using Screening Type B (11.2 mm) Aggregate)

Sr No..238Providing and laying 125 micron Low Density Polyethylene (LDPE) sheet confirming to IS 3395 : 1997 below concrete pavement including all materials and labour complete.

Sr No..239Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate ( natural sand/ VSI grade finely washed crushed sand) conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, , cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant/ Weigh batch mixer, transported to site with all leads and lifts, laid with a paver with electronic sensor /by suitable means as approved by Engineer-in-charge , compacting with vibratory roller, finishing, curing and including preparation of sub-grade surface if required etc. complete. with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete.

Sr No..240Providing and laying in-situ M40 Grade unreinforced plain cement concrete pavement with max 20% fly Ash ( Fly-ash upto 20% by weight of Cement) over a prepared sub base with 43 grade cement , coarse and fine aggregate ( natural sand/ VSI grade finely washed crushed sand) conforming to IS 383, using fine and coarse aggregates combined gradation as per Table 600-3 of MORTH Specification 2013, mixed in a Tilting type Concrete Mixer as per approved mix design, admixtures, spreading, laying compacting and finished in a continuous operation without paver machine, finishing to lines and grades as directed by Engineer-in-charge and curing by curing compound /by providing cement vata in cement Mortar 1:8 @0.6m X 0.6m centre to centre, admeasuring 80 mm at bottom and 40 mm at top with depth of 75mm and maintaining the same throughout curing period by any other method approved by Engineer-in-charge. with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete.

Sr No..241Providing and fixing in position TMT FE 500, 25mm dia dowel bars precoated with anticorrosive epoxy paint of required Dia. 60 cms. Long and at 30.00 cm. C/C and wherever directed including handling, straightening, necessary cutting supported by TMT FE 500, chairs with proper alignment by using properly designed assembly of Bulkheads lubricating half length with bituminous paint as directed etc. complete.

Sr No..242Providing and casting in situ or precast tapering R.C.C. M-20 Barrier type Kerb with gutter ( as per IRC 86 1983) embedded 125mm below ground level over M-10 PCC finished neatly with C.M. 1:2, setting the same in C.M. 1:2, including the required excavation in any strata and removing the excavated stuff any where in city and redoing the surface as specified and directed by Engineering In-charge. Using Concrete Batching and Mixing Plant

Sr No..243Road Marking with Hot Applied Thermoplastic Compound with Reflectorizing Glass Beads on Bituminous Surface- Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorizing glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.complete.

Sr No..244Providing and fixing Artistic information sign boards of size 1.50 x 0.60 Meter or Opal Shape having Area between 0.9 to 1.2 Sqm (with Epoxy Resin or approved brand water repelent coating on wood) prepared from seasoned wooden planks on a frame of size 35 x 35 x 5 mm with cross bracing of size 35 x 35 x 5 mm, including bonded with IRC specified color of retro reflective sheeting of Type IV High-Intensity Micro-Prismatic Grade Sheeting (HIP) having pressure sensitive/heat activated adhesive. The messages on the board represent detailed illustrations of marine life, likely from the surrounding mangrove area, providing more in-depth educational content, will have pressure-sensitive adhesive, with the border and messages in IRC-specified color on the background. The board will be supported by two wooden posts of size 65 x 65 mm and 3.65 m long, inflated at the bottom, drilled on top, and painted in white and black bands of 30 cm. The posts will be fixed with 4 Nos. high strength G.I. bolts and nuts of size 10 mm dia. and 20 mm long, ensuring that the wooden sheet and post are in one piece without joints. This includes all taxes, conveying, and fixing in the ground with cement concrete 1:4:8 block of 60 cm x 60 cm x 75 cm size, as directed by the Design Consultant & Engineer-in-charge, complete in all respects.(Including 5 Years of Maintenance)

Sr No..245Design, Approved from Competent Authority (JJ School of Arts and Equivalent) , Engraved / Making, Transportation, and Installation of a Outdoor seasoned wooden Portrait, including base, features of 6 ft x 4 ft tall Custom Handcarved 3D Wood Portrait, inspired by renowned Indian personalities in the fields of art and culture. Crafted using sustainable, eco-friendly materials such as bamboo, wooden sticks, and natural fibers, these portraits will represent the Famous Personalities likes of Lata Mangeshkar, Sachin Tendulkar ,Naba Kishore Dutta (Environment Activist) , Kalpana Chawla etc. and others who have significantly contributed to Indian in various fields. Each sculpture will embody the essence of these personalities while integrating seamlessly with the natural mangrove environment. The design will emphasize the harmony between culture and nature, encouraging visitors to engage with both Indian heritage and the surrounding ecosystem. Positioned along the trail, these sculptures will serve as both educational and artistic installations, promoting awareness of India’s rich cultural legacy while highlighting the importance of sustainability. The use of natural, biodegradable materials not only aligns with the park's eco-conscious mission but also ensures the artwork's aesthetic evolves with time and weather, creating an organic, living tribute to these personalities, as directed by the Design Consultant & Engineer-in-charge, complete in all respects.(Including 5 Years of Maintenance)

Sr No..246Design, Approved from Competent Authority (JJ School of Arts and Equivalent), Making , Transportation, and installation of an outdoor seasoned stunning bamboo sculpture including the base captures the fluidity and grace of a Maharashtrian Native Woman or an Indian classical dancer mid-performance, embodying the rich cultural heritage of India's performing arts. Standing life size Sculpture, the figure’s intricate detailing showcases the dynamic movement of the dance, with the dancer’s posture and attire skillfully represented through woven bamboo. The sculpture honors India’s diverse dance traditions and is a powerful reminder of the country’s artistic legacy. Placed along the Mangrove Park trail, this sculpture not only enhances the cultural ambiance of the park but also educates and inspires visitors by highlighting the significance of art and performance in Indian culture, all while promoting sustainability through its eco-friendly design.as directed by the Design Consultant & Engineer-in-charge, complete in all respects.(Including 5 Years of Maintenance)

Sr No..247Design Conceptualisation , Approved from Competent Authority (JJ School of Arts and Equivalent) & painting of Varli artwork on any In door or outdoor surface at all height and locations. This Painting depicts a vibrant rural scene, featuring geometric shapes, simple lines, and white figures against a dark background. The artwork showcases traditional village life, including houses, animals, and human figures engaged in various activities. The composition is balanced and harmonious, with a focus on the interconnectedness of nature and human life as directed by the Design Consultant & Engineer-in-charge, complete in all respects.(Including 5 Years of Maintenance)

Sr No..248Design Conceptualisation , Approved from Competent Authority (JJ School of Arts and Equivalent) & painting of Pithora artwork on any In door or outdoor surface at all height and locations. This Painting portrays a narrative scene, often depicting religious themes or mythological stories. The artwork is characterized by its bold outlines, flat colors, and intricate patterns. The composition is carefully planned, with each element contributing to the overall storytelling directed by the Design Consultant & Engineer-in-charge, complete in all respects.(Including 5 Years of Maintenance)

Sr No..249Designing, Conceptualization & painting of 3D artwork on any surface at all height and location as directed. The paint should be used for the artistic painting is high quality acrylic paint. painting should be coated with weather proof warnish.

Sr No..250Providing, Installation & Supplying Cement Planter having size of 18”x 18” x 18” of Good quality, durable, well finished on edge with good strength

Sr No..251Providing, Installation & Supplying Cement Planter having size of 24” x 12” x 12” of Good quality, durable, well finished on edge with good strength

Sr No..252Providing, Installation & Supplying Cement Planter having size of 36” x 18” x 18” of Good quality, durable, well finished on edge with good strength

Sr No..253GARDEN SOIL:- Supplying on site garden soil well sieved 80 % to pass through I.S. sieve of 10 mm size free from stones rubbish like dried grass roots and other such materials. The soil should be fresh from quarry. The color of the soil generally is red. The soil will be measured by measuring box. (Farma) Item includes Transporting, loading -unloading etc (.Lead charges per 70 km. considered Excluding royalty.)

Sr No..254FARM YARD MANURE: - Supplying on site well decayed, well dried, well powdered, without clods and free from stones, dried grass and other rubbish material. The color of the manure generally is black. The manure will be measured by measuring box. (Farma) Item includes Transporting, loading -unloading etc (.Lead charges per 50 km. considered.)

Sr No..255Providing and applying two coats of exterior acraylic emulsion paint confirming to corresponding I.S. of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface, applying primer coat ,scaffolding if necessary , and watering the surface for two days etc complete.

Sr No..256Mixing garden soil/silt & manure thoroughly well, watering previous night. Planting required plant species; lawn grass as directed etc. complete for required depth 5 to 30 cms. for planting lawn/ shrub/ flower bed/ hedges/ edges/ canna bed/ ground cover.

Sr No..257Providing Supplying Dracaena Golden on site (free from weeds /diesease etc.) 30 cms. apart c/c.);Bag Size 8" Pots , Plant Height 30 cm to 45 cm

Sr No..258Providing Supplying Dracaena Green on site (free from weeds /diesease etc.) 30 cms. apart c/c.);Bag Size 8" Pots , Plant Height 30 cm to 45 cm

Sr No..259Providing Supplying Dracaena Golden on site (free from weeds /diesease etc.) 30 cms. apart c/c.);Bag Size 8" Pots , Plant Height 30 cm to 45 cm

Sr No..260Providing Supplying Raphis palm on site (free from weeds /diesease etc.) 30 cms. apart c/c.);Bag Size 10" x 12" Pots , Plant Height 3 to 4 ft.

Sr No..261Providing Supplying Areca Palm on site (free from weeds /diesease etc.) 30 cms. apart c/c.);Bag Size 8" Pots , Plant Height 3 to 4 ft.

Sr No..262Providing and Fixing , Installation of Drip and Sprinkler Irrigation system in gardens having area Up to 1000 Sq. Mtr. Incudes drips, Sprinkler, Filters, Pipes With 3 year warranty . Excluding Pumping Unit (Installation of drip and sprinkler irrigation system that includes main water lines, laterals, sublateral, driper and sprinkler and all spare parts required for Irrigation system , Excluding pumping system only

Sr No..264Providing and Supplying the 8-seater boat designed for mangrove tourism in the Mangroves Creek Project will adhere to the specifications outlined in the provided image. With a maximum length of 400 cm, a width of 170 cm, and a depth of 55 cm, the boat will offer ample space for passengers. The roto-molded double-skin HDPE hull will ensure durability and safety. Powered by a minimum 30 HP outboard motor, the boat will be equipped with essential accessories such as mooring rings, cleats, a storage bench, a foldable canopy, life jackets, and navigational instruments. The boat will be sourced from reputed Indian brands such as Mutha Boats, Oceanic Boats, or Aquatech, known for their high-quality tourist and rescue boats. It will also be accompanied by a suitable trailer with a galvanized steel frame, 13-inch wheels, and a high-quality winch. This well-equipped vessel, directed by the Engineer-in-Charge, will provide a comfortable and safe experience for tourists exploring the Mangroves Creek. The package includes 5 years of maintenance, ensuring long-term reliability and performance.

Sr No..265Providing and Supplying The single-seater kayak similar to Aquaterra Adventure or similar approved brand With an average length of 280 centimeters and a width of 65 centimeters, these lightweight vessels are easy to maneuver through narrow channels and dense mangrove forests. Constructed from durable materials like polyethylene single-seater kayaks are equipped with comfortable seats, footrests, and high-quality paddles with Essential safety gear such as life jackets and whistles are also provided. directed by the Engineer-in-charge, complete in all respects.(Including 5 Years of Maintenance)

Sr No..266Providing and supplying double-seater kayaks similar to Aquaterra Adventure or similar approved brand with an average length of 340 centimeters and a width of 80 centimeters. These spacious yet lightweight vessels are designed for easy maneuverability through narrow channels and dense mangrove forests. Constructed from durable materials like polyethylene, the kayaks feature two comfortable, adjustable seats with footrests to ensure a pleasant paddling experience for both occupants. Each kayak comes with high-quality paddles and essential safety gear, including life jackets and whistles. The design emphasizes stability and ease of use, making it suitable for both experienced paddlers and beginners. Installation and maintenance will be directed by the Engineer-in-Charge, with a comprehensive five-year maintenance plan included to ensure ongoing durability and optimal performance.

Sr No..267Supply a superior modular floating jetty , made of LL36RA045UV is a butenecomonomer based Liner Medium Density Polyethylene (LLDPE) material with Resin(LLDPE) with antioxidants and UV stabilizers. Each floating Pontoon Cubes have sizes of 500mm X 500mm X 400mm, and weight around 7.5 kg all in a color of Natural, blue, grey, orange, and yellow.The jetty should have high-density rubber dog-bone-shaped connectors for linking the modular pontoons. Made of PE with 11 UV stabilization, the jetty must be CSIRO slip-resistant certified, featuring a raised tile pattern deck that is self-draining. It should be highly resistant to degradation, impact, and inert to most chemicals, with temperature resistance ranging from -10°C to 60°C. Each pontoon must provide buoyancy of 350 kg at 50% submersion in water, making it ideal for a versatile, durable floating pontoon solution. This floating jetty should meet the highest standards of safety and performance for use in the tourism project, ensuring a long service life in demanding environmental conditions India Bungy , Roto tech or equivalent Brand Manufacturer all as directed by Engineer In Charge

Sr No..268Providing and fixing informatory sign boards in rectangular shape of size 1.20m x 0.90m made out of 16 guage Aluminum panel bonded with IRC Specified colour of retro reflective sheeting of Type IV High Intensity Micro-Prismatic Grade Sheeting (HIP) having pressure sensitive / heat activated adhesive, IRC Specified colour retro reflective cutout border & messages having pressure sensitive adhesive having border & messages in IRC Specified colour background including M. S. angle iron frame of size 35 mm X 35 mm X 3 mm & two M.S. angle iron post of size 65 mm X 65 mm X 6 mm, 3.65 m long, duly painted with flat oil paint having alternate black and white bands of 25 cm width including G.I. fixtures etc; fixing the boards in M-20 concrete block of size 60cm X 60cm X 75cm including transportation etc; complete. Aluminum Panel Type IV High Intensity.

Sr No..269Providing and fixing sign boards of size size 60 x 80 cm made out of 14 gauge M.S.Sheet with retro reflective sheeting of Engineering Grade as per M.O.T. specification No. 801-3(1993) white reflective back ground, lettering symbol bordering of black non reflective paint including 3.65 metre long M.S.angle one post of 65 x 65 x 6 mm size duly painted with white and black bands including fixing the boards of M.S. angle with galvanised nuts and bolts and washer. The Board shall be as per IRC-67-1977 including conveying fixing in ground with C.C. 1:4:8 block of size 0.60 x 0.60 x 0.75 m, with 7 year guarantee for the sheeting etc. complete. Mild Steel Board with Engineering Grade.

Sr No..270Providing Biotoilet of 4 units of 0.9*1.2M size of 1 unit with Bio Digester and all necessary fittings such WC Wash basin overhead tank of 1000 ltr for each Type of WC : European with ceramic base , Water facility : By mean of overhead tank, Electric provision By mean of connection from main line, Bottom frame material: 35mm X 35mm X 5mm(thick) MS angle for one seater, Bottom frame support material : 25mm X 25mm X 3mm(thick) MS angle, Side & Top Roof panel frame material : 35mm X 35mm X 5mm(thick) MS angle, Top(roof) support frame structure : 25mm X 25mm X 3mm(thick) MS angle, Ventilation frame material: 25mm X 25mm X 3mm(thick) flat MS, Door frame material: 35 mm x 35 mm x 5 mm (thick) MS ANGLE, Support material for Door panel fixing: Aluminium U-channel of 18gauge, Door hinges(two numbers): 75mm size with 1.2-1.5mm thickness MS, Tank holder frame material: 25mm X 3mm(thick) MS flat, Unit understructure Supported by 4-legs of size 35mm X 35mm X 5mm MS angle with corner support of 25mm x 25mm X 3mm MS angle for 1-seater, Door Tee material: 40mm X 40mm x40mm X 5mm(thick) MS Tee, Side panel material: 5mm thick ply core sandwich with 1mm thick FRP from both sides(5+1+1mm), Top(Roof) panel material: 5mm thick ply core sandwich with 1mm thick FRP from both sides(5+1+1mm), Door panel material: 5mm thick ply core sandwich with 1mm thick FRP from both sides(5+1+1mm), Partition panel material: 5mm thick ply core sandwich with 1mm thick FRP from both sides(5+1+1mm) ,Floor material: 5mm thick FRP material with necessary pipe fittings electric fittings etc complete as approved by Engineer-In-Charge

Sr No..271Providing Steel Porta Cabin consist of With one Room of size 3050 mm x 2440 mm x 2590 mm ht having following specifications. 1) PUF Wall Panel – Panel made up of micro ribbing Pre-Painted Galvanized Iron Sheet on both sides(have tongue groove arrangement) and 50mm thick composite PUF sandwich between Pre-Painted Galvanized Iron Sheet 2) Flush door 32 mm thick water proof. 3)Window-Powder coated aluminium sliding windows with 4 mm tinted Glass 4)Flooring- 15 mm heavy duty cement fiber board inside and outside texture paint. 5)Roofing -The PUF insulated Ceiling panels. The covering on ceiling panels shall be micro riving Pre-coated galvanized iron sheet and Self draining Type Roof shall be provided with water proof covering. 6) general electrical- Provision for 3 nos. tube light (18 Watt LED light) - 2 nos. wall mounted ceiling fan (300 mm) - 3 nos. plug and socket (3 pin 5 amps electric plug socket)- 1 no main input socket (32 Amp heavy duty 3 pin power socket with MCB)- split AC (1.5 T) provision

Sr No..272Nameplate (3D acrylic hollow blocks with LED) S.I.T.C. of Nameplate stating in Devnagri/English font in the desired style as per specifications. The total asembly letters made of frosted acrylic sheets 5mm thick cut and glued together to achieve the hollow letters (side edges of letter made up of in Aluminium Composite Panel) as per approved design with provision for electrical supply for white/warm white LED lights of required wattage that will be lit from inside the blocks for illumination in the night. The whole assembly shall be rested/fixed with all necessary fittings and cleaning including supporting , M.S. Fabrication work etc. with required size C.C. foundation complete as directed by the Engineer-in-charge.

Sr No..273Civil Maintenace : Providing and applying 2 coats of 100% Pure acrylic low VOC and APEO & HCHO free water based paint of approved colour that belongs to class 1 flame spread resistance of approved make Paint should provide durable and long lasting silk finish with a high crack tolerance of upto 1mm. Paint should have an oustanding washability with high resistance to wide range of bacteria and fungus. Paint has to be applied on smooth and uniform surface prepared by an acrylic copolymer low VOC & Odour putty. This surface should be primed with water based low VOC Primer. The work activity should cover all aspects of applying paints from surface preparation as directed by Engineer in charge.

Sr No..274For 1st Floor

Sr No..275For 2nd Floor

Sr No..276For 3rd Floor

Sr No..277For 4th Floor

Sr No..278Providing and laying machine cut machine polished machine cut Kota stone slabs 20 to 25 mm thick for treads and risers of steps and staircases, with rounded nosing for the treads on a bed of 1:4 cement mortar including cement float, filling joints with neat cement slurry, curing, polishing and cleaning etc. complete Ground Floor

Sr No..279For 1st Floor

Sr No..280For 2nd Floor

Sr No..281For 3rd Floor

Sr No..282For 4th Floor

Sr No..283Providing and laying in position flooring of telephone black / Amba White / Cat bary brown / Ruby red / Ocean Brown granite stone of approved shade and size 18 mm to 20 mm thick on bed 1:6 cement mortar including cement floats striking joints, pointing in C.M. 1:3 curing and cleaning etc. complete. Ground Floor

Sr No..284For 4th Floor

Sr No..285Providing and laying Polished Kota stone flooring With Hand-Cut Polished Kota Stones 25mm to 30mm thick and required width in plain/diamond pattern on bed of 1:6 Cement mortar including cement float, filling joints with neat cement slurry, curing, cleaning and Mirror Polishing etc. complete Note- Water absorption for kota stone should not exceed 0.05%.( Item to be used with prior permission of Superintending Engineer ) Ground Floor

Sr No..286For 1st Floor

Sr No..287For 2nd Floor

Sr No..288For 3rd Floor

Sr No..289For 4th Floor

Sr No..290Providing leather finished polishing to Kota / Marble / Shahabad / Kadappa Stone slab by continuous grinding in 4 coats of different bits to receive rough and matty finish including buffing process before laying and fixing of stone as per drawing and design, including cleaning, washing and finishing etc. complete.Ground Floor

Sr No..291For 1st Floor

Sr No..292For 2nd Floor

Sr No..293For 3rd Floor

Sr No..294For 4th Floor

Sr No..295Providing and laying 800 x 800 x 9 to 10 mm thk. vitrified tiles as specified below conforming to I.S.15622-2006 with water absorbtion less than 0.08% for flooring of an approved, quality, make, pattern and size for flooring including cement mortar bedding of 25 mm thick in 1:4 proportion, cutting, leveling, jointing, filling the joints by neat cement slurry or approved colour grout, curing, finishing etc complete as directed by Engineer In Charge.

Sr No..296Providing and laying at site 8mm thick laminated flooring having an inbuilt 1mm soundbloc CS backing - class of use 33/23, wear resistance AC-5, impact resistance - IC 3, (as per EN 13329), top surface having a MLC (Multi Layer Composite) high pressure laminate, top surface treated with (Aluminium Oxide) surface guard (tm) plus on top of high density fibreboard substrate (density 910 kg/m3) specially developed core; of plank size 1994mm x 194mm having smart lock tounge and groove joints to secure long lasting joint. The edge of tounge and groove of planks duly impregneted with paraffin. The approved decor planks to be placed on underly - 0.2mm thick alkali resistant polythylene sheet (Density 935 Kg/m3) to resist any moisture movement from the sub floor and secure floating floor installation. Pergo original conforms to EN 13329, ASTM C 1028, DIN 52185, DIN 54345, EN 717-2, DIN 4102.oring

Sr No..297Bamboowood 20mm thick Decking Outdoor Flooring Tile Providing & fixing in position Phenol bonded Epitome Bamboowood deck flooring tiles with planks of sizes 20mm thick, 1900 mm length and 135mm wide ,in approved colour , texture and finish , having performance Appraisal Certificate (PAC) issued by Building Materials& Technology promotion Council (BMTPC)with necessary profiled edges and groove fixed with 40mm ss screws 3 nos in each tile to frame work made of second class seasoned and treated teak wood of size 38x38 mm placed underneath acoss the tile at both ends and in centre fixed with clips holding in position. The Epitome Bamboowood planks shall have minimum density of 1000 Kilogram/cum & minimum hardness 1000 Kilogramf.all complete as per direction of engineer in-charge.Ground Floor

Sr No..298For 4th Floor

Sr No..299Providing and laying in place 300mm x 300mm x 9.8mm vitrified tactile warning and directional tiles of the approved brand, make and colour inside the buildings at in all corridors and lobbies, level differences etc. as per accessibility standards and as per the installation instructions prescribed by the manufacturer including zarri making wherever required and finishing including grouting the joints with white cement with matching pigments etc. up to the satisfaction of the engineer in charge complete.Ground Floor

Sr No..300For 1st Floor

Sr No..301For 2nd Floor

Sr No..302For 3rd Floor

Sr No..303Point wiring for independent plug, concealed type in min 20 mm HMS PVC conduit with 1.5 sq.mm (2+1E) FRLSH grade copper wires, modular type switch and socket, earthing and required accessories as per specification No WG?PW/SW

Sr No..304Point wiring for light/bell concealed type in min 20 mm HMS PVC conduit with 1.5 sq.mm. (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories as per specification no. WG-PW/CW

Sr No..305Point wiring for ceiling fan concealed type in min 20 mm HMS PVC conduit with 1.5 sq.mm. (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories as per specification no. WG-PW/CW

Sr No..306Supplying, erecting & terminating 2 pair telephone copper cable 0.5 mm dia. with high density polyethylene insulation, polyester taped, nylon rip cord & grey colour sheathed with FR PVC, confirming to ITD specification S/WS 113C laid in provided PVC casing-n-capping/conduit as per specification no. WG-TW

Sr No..307Supplying, erecting & terminating 20 pair telephone copper cable 0.5 mm dia. with high density polyethylene insulation, polyester taped, nylon rip cord & grey colour sheathed with FR PVC, confirming to ITD specification S/WS 113C laid in provided PVC casing-n-capping/conduit as per specification no. WG-TW

Sr No..308Supplying, erecting & commissioning MDF Box 50x50 pairs made from min. 1.5mm thick MS sheet as per specification no. WG-TA

Sr No..309Supplying & erecting rosette box RJ type bakelite box on wall with LED indication duly connected as per specification no. WG-TA

Sr No..310Supplying and installing LSZH sheathed HDPE insulated copper cat-6A cable suitable for networking compliant with ANSI/TIA-568.2-D standards in provided conduit/casingn-capping as per specification no. WG-ELVC/NC

Sr No..311Supplying and erecting LED square / circular Max. 14 W down lighter / Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 1500 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs at L70B50 including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with minimum 2 years warranty as per specification No. FG-IDF/LED.

Sr No..312Supplying and erecting LED square / circular Max. 18 W down lighter / Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 2000 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs at L70B0 including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with minimum 2 years warranty as per specification No. FG-IDF/LED.

Sr No..313Supplying and erecting LED square / circular Max. 25 W down lighter / Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 2750 Lumens, min. efficacy of 110lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs at L70B50 including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with minimum 2 years warranty as per specification No. FG-IDF/LED.

Sr No..314Supplying and erecting anodized aluminium light LED fitting (4 feet) Max. 22W with high transitivity diffuser with system lumens output of Min.2200 lumens , min. efficacy of 100 lumen/W, CRI>80, CCT upto 6000K, Beam Angle of 110 deg., Ripple0.95, operating range of 200-270V, surge protection of 2 kV, Life class of 50,000 Hrs at L70B50 including driver with end caps on provided PVC Block/wooded board with minimum 2 years warranty as per specification No. FG-IDF/LED.

Sr No..315Supplying LED concealed type foot / step light with aluminium body for indoor / outdoor application suitable for 4W - 6W LED including driver and erecting by making necessary arrangement / recess in wall to make it flush with surface with minimum 1 year warranty as per specification No. FG-IDF/LED.

Sr No..316Supplying and erecting integrated LED round burial light 6W IP65 & IK10 class having pressure die-cast housing, having system lumens output of Min. 500 Lumens, min. efficacy of 85 lumen/W, CRI>80, CCT upto 6500K, THD<10%, p.f. >0.90, operating range of 100-240V, inbuilt surge protection of 2 kV, Life class of 50,000 Hrs at L50B50 , slat spray tested for 500 Hrs. including making of recess of appropriate size for flushing into surface with minimum 2 Year warranty as per specification No FG-ODF/PT

Sr No..317Supplying & erecting inverter LED batten 20W tube light fitting with polycarbonate housing, heat sink, integrated HF electronic driver, Min. 2600 mA Lithium ion Battery with charging time of 8-10 Hours and backup time of Min. 3 Hrs with minimum 25% of initial Watts having luminous efficacy of 100 lumen/watt, CRI>80, CCT of 6500K and THD<=20 % having useful life of minimum 25000 Hrs with over heat protection with minimum 2 years as per specification No. FG-IDF/LED.

Sr No..318Supplying and erecting integrated LED street light Luminare fitting 60W IP65 minimum 5 Years warranty as per specification No. FGODF/ SL.

Sr No..319Supplying and erecting Street light bracket made from 40 mm. dia ‘B’ class G.I. Pipe, 0.6m. in length along with pole cap of 300 mm length and 80 mm dia duly welded with provided leads as per specification no. FG-BKT/BPC

Sr No..320Providing & erecting 3 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 130 mm A/F, top 70 mm A/F on provided foundation as per specification no. OH-PL/OPL

Sr No..321SITC of street light control panel inclusive of all electrical accessories mentioned in tender document. (with IOT based smart lighting system with 3 nos of CT for inc in side

Sr No..322Supplying, erecting & marking SPMCB 0.5A to 5A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-MCB

Sr No..323Supplying and erecting integrated LED Bollard Cylindrical / Cubical shaped 800mm 8W IP65 & IK10 class having extrusion aluminium housing with polycarbonate diffuser, having system lumens output of Min. 800 Lumens, min. efficacy of 100 lumen/W, CRI>80, CCT upto 6500K, THD<10%, p.f. >0.90, operating range of 140-240V, inbuilt surge protection of 2 kV, Life class of 25,000 Hrs. at L50B50, including driver complete with minimum 2 Year warranty as per specification No FG-ODF/BL

Sr No..324Supplying and erecting exhaust fan medium duty 230 V A.C. 50 cycles 225 mm. 1400 RPM with condenser complete erected in position with necessary materials. Fan motor with moisture proof treatment and ‘E’ class insulation

Sr No..325Supplying and erecting Energy Saving BLDC Ceiling fan 230 V A.C. 50 cycles 1200 mm, Max. Energy Consumption of 28W having service ratio (CMM/W) of Min. 8 , PF>0.9, THD<10% with IR remote control, Temperature Rise of Max. 40 deg.C, having external mounted control PCB completely erected in position as per specification no. FG-FN/CF

Sr No..326Providing and Fitting of 15W LED track light of three light in each track of 3 m length Including all labour, material, handling, and transportation costs included and as directed by engineer-In-Charge

Sr No..327Supplying and erecting LED Strip light Max. 45 W IP20 class having minimum lumens output of 800 Lumens/m, min. efficacy of 90 lumen/W, CRI>80, CCT upto 5000K, Beam Angle of 110 deg., THD<10%, p.f. >0.95, operating range of 230-270V, Life class of 30,000 Hrs at L70B50 including driver with minimum 1 year warranty as per specification No. FG-IDF/LED.

Sr No..328Supplying & erecting triple pole and neutral distribution board (TPNDB), SP/TP MCBs total 8 ways/24 poles, with door, 1.2mm thickness surface/flush mounted, IP 43 Protection on provided iron/GI frame (vertical busbar type) as per specification no. SW-MCBDB.

Sr No..329Supplying & erecting triple pole and neutral distribution board (TPNDB), SP/TP MCBs total 4 ways/12 Poles, with door, 1.2mm thickness surface/flush mounted, IP 43 Protection on provided iron/GI frame (vertical busbar type) as per specification no. SW-MCBDB.

Sr No..330Supplying and erecting PVC Surface modular switch box with double mounting plate for 2 module complete

Sr No..331Supplying and erecting PVC Surface modular switch box with double mounting plate for 4 module complete

Sr No..332Supplying and erecting PVC Surface modular switch box with double mounting plate for 6 module complete.

Sr No..333Supplying and erecting PVC Surface modular switch box with double mounting & front plate for 8 module complete duly connected.

Sr No..334Supplying and erecting PVC Surface modular switch box with double mounting plate for 12 module complete.

Sr No..335Supplying and erecting PVC Surface modular switch box with double mounting plate for 16/18 module complete.

Sr No..336Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 2 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background

Sr No..337Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 4 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Sr No..338Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 6 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background

Sr No..339Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 8 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background

Sr No..340Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 12 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Sr No..341Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 16 / 18 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Sr No..342Supplying & erecting triple pole and neutral distribution board (TPNDB), 3 pole MCCB as incomer & outgoing SP MCB (12 poles) or TP MCB of 4 ways (12 poles), with door, 1.2mm thickness, surface/flush mounted, on provided iron/GI frame (vertical busbar type) as per specification no. SW SWR/MCBDB1

Sr No..343Supplying & erecting triple pole and neutral distribution board (TPNDB), 3 pole MCCB as incomer & outgoing SP MCB (24 poles) or TP MCB of 8 ways (24 poles), with door, 1.2mm thickness, surface/flush mounted, on provided iron/GI frame (vertical busbar type) as per specification no. SW-SWR/MCBDB1

Sr No..344Supplying & erecting triple pole and neutral distribution board (TPNDB), 3 pole MCCB as incomer & outgoing SP MCB (36 poles) or TP MCB of 12 ways (36 poles), with door, 1.2mm thickness, surface/flush mounted, on provided iron/GI frame (vertical busbar type) as per specification no. SW SWR/MCBDB1

Sr No..345Providing & erecting floor/wall mounting, MCCB panel board, with door, suitable for 4 pole incoming 400A, 8 ways 4 pole outgoing, up to 100A MCCBs on iron frame, as per specification no. SW-MCCBPB. (Excluding MCCBs)

Sr No..346Providing & erecting floor/wall mounting, MCCB panel board, with door, suitable for 4 pole incoming 400A, 12 ways 4 pole outgoing, up to 100A MCCBs on iron frame, as per specification no. SW-MCCBPB. (Excluding MCCBs)

Sr No..347Supplying, erecting & terminating FR XLPE insulated, galvanised steel wire armoured (round) cable, 1100 V 4 core 6 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Sr No..348Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable, 1100 V 4 core 10 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Sr No..349Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable, 1100 V 4 core 16 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Sr No..350Supplying, erecting, testing and commissioning of flat flexible 3 core 6 sq.mm PVC sheathed submersible type copper cable suitably clamped at fixed intervals with column pipe assembly complete.

Sr No..351Supplying and erecting recess type, 3 pin plug socket 6A with piano switch 6 A combined unit erected on polished double wooden block/ folded or screwed board with top of either wooden or plywood pasted with sunmica and with connecting leads

Sr No..352 Supplying and fixing Cat 6, keystone jack RJ-45 information outlet compliant with ANSI/TIA/EIA 568.C.2 & ISO/IEC 11810 (ethernet) as per specification no. WG-NAS/KJ

Sr No..353Supplying and erecting electronic type step regulator for ceiling fan 600/ 900/ 1200/ 1400 mm. sweep, complete erected on provided switch board.

Sr No..354Supplying and erecting LT CT multifunction DLMS compliance energy meter of accuracy of class 0.5, 3x240V, 50 Hz with optical & RS 232 port, backlit LCD, measures & displays trivector energy, load survey, TOD, tamper detection & logging, power ON /OFF events, instantaneous parameters of rating 1/5 A with display in absence of power complete with zero adjustment & test certificate from manufacturer erected on provided M.S. box and connected to CTs.

Sr No..355Supplying, erecting, testing & commisioning metal work in CRCA sheet including Iron work for supports with fabrication of boxes, panel boards, etc. including cutting, bending, drilling, welding, riveting, treated with anti-rust treatment and painted with one coat of red lead paint and 2 coats of enamel paint or powder coating complete as per specification no. CP/SH/CR

Sr No..356Supplying & laying HMS PVC conduit 20mm dia. with necessary accessories in RCC work/false ceiling/false flooring as per specification no. WG-MA/CC.

Sr No..357Supplying & laying HMS PVC conduit 25mm dia with necessary accessories in RCC work/false ceiling/false flooring as per specification no. WG-MA/CC.

Sr No..358Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable, 1100 V 3½ core 240 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Sr No..359Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable, 1100 V 3½ core 25 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Sr No..360Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable, 1100 V 3½ core 35 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Sr No..361Supplying, erecting & marking SP MCB 6A to 32A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-MCB

Sr No..362Supplying, erecting & commissioning 4 pole RCCB 40A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB.

Sr No..363Supplying, erecting, testing & commisioning bus bar chamber triple pole with neutral with four copper bars, 500V, 100A having 10mm ( width) x 1.6 mm (thickness), with 99.9 % copper purity as per E91E grade & current density 1.6 A per sq mm compliance to IS 5082 and enclosure fabricated with 16 SWG CRCA sheet and epoxy paint, with suitable number of ways and with SMC/DMC insulators and accessories of suitable rating and two nos of separate earthing terminals complete as per specification no. CP-BB

Sr No..364Supplying and erecting panel mounting type digital voltmeter having three and half digit LED display, calibrated for 0 to 750V AC suitable to operate on 500V having accuracy class of 0.5, AC supply with necessary PVC wire leads and lugs and mounting hardware on provided panel complete with calibration certificate from manufacturer.

Sr No..365Supplying and erecting panel mounting type digital ammeter having three and half digit LED display, external CT operated, calibrated for suitable to operate on 500V, 0 to 1000A having accuracy class of 0.5, AC supply with necessary PVC wire leads and lugs and mounting hardware on provided panel complete with calibration certificate from manufacturer

Sr No..366Supplying, erecting & marking TP MCB 6A to 32A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-MCB

Sr No..367Supplying, erecting and marking 4 pole isolator only switch version of miniature circuit breakers of 40A in provided distribution board.

Sr No..368Supplying, erecting and marking 4 pole isolator only switch version of miniature circuit breakers of 63A in provided distribution board.

Sr No..369Supplying, erecting & marking SP MCB 6A to 32A, B-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-MCB

Sr No..370Supplying, installing, testing & commissioning 3 phase, 22/0.433 kV, 50 Hz., 250 kVA, Mineral oil immersed and naturally cooled outdoor type, Copper wound, without gas cushioning, hermetically Sealed transformer, delta/star connected with additional neutral brought out on load side, temperature rise should not exceed 45℃ by thermometer in oil and 50℃ by the resistance method in winding at full load rating, using type A winding insulation (kraft paper) with HV tapping (with off load tap changer) off load +5 to -10 in steps of 2.5%,having 7 number of tap positions , with standard accessories complete with test certificate with losses below 1029 Watts at 50% load, 3077 Watts at 100% load as per IS:1180 (part 1) : 2014 with necessary permissions of Electrical Inspector, as per specification no SS- TR-HSL.

Sr No..371CC Foundation for transformer

Sr No..372Supplying and erecting fencing of section having size at least 2450 mm in height from ground level and 1200 mm width with angle iron frame work erected in CC foundation and painted complete with provided earthing as per specification no. SS-AS/FSG

Sr No..373Supplying, erecting, testing & commisioning bus bar chamber triple pole with neutral with four aluminium bars, 500V 400A having 50mm ( width) x 5 mm (thickness), with 99.9 % aluminium purity as per E91E grade & current density 0.8 A per sq mm compliance to IS 5082 and enclosure fabricated with 16 SWG CRCA sheet and epoxy paint, with suitable number of ways and with SMC/DMC insulators and accessories of suitable rating and two nos of separate earthing terminals complete as per specification no. CP-BB

Sr No..374Supplying & erecting LED type indicating pilot lamp with LED colours red / yellow / green, 230 / 250V on provided box / panel with necessary material, wiring & connections etc.

Sr No..375Providing & erecting 4 Pole MCCB 415V, 400A, rated short-circuit breaking capacity 36 kA (Ics=100% of Icu), adjustable thermal (overload) setting and adjustable magnetic setting with provided leads, provision for installation of shunt/ UV/ trip alarm contact. MCCB should have phase barriers both sides, with insulation withstand capacity 800V, no line-load bias in provided enclosure /panel as per specification no. SW-MCCB

Sr No..376Providing & erecting 4 Pole MCCB, 415V, up to 100A, rated short-circuit breaking capacity 25 kA (Ics=100% of Icu), adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/UV/trip alarm contact. MCCB with phase barriers on both sides, insulation withstand capacity 800V, no line-load bias in provided enclosure/panel as per specification no. SW-MCCB

Sr No..377Supplying, erecting & marking TP MCB 40A to 63A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-MCB

Sr No..378Supplying, erecting & commissioning 4 pole RCCB 40A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB.

Sr No..379Supplying, erecting, testing & commisioning bus bar chamber triple pole with neutral with four aluminium bars, 500V, 100A having 15mm (width) X 3 mm (thickness), with 99.9 % aluminium purity as per E91E grade & current density 0.8 A per sq mm compliance to IS 5082 and enclosure fabricated with 16 SWG CRCA sheet and epoxy paint, with suitable number of ways and with SMC/DMC insulators and accessories of suitable rating and two nos of separate earthing terminals complete as per specification no. CP-BB

Sr No..380Supplying , erecting & terminating XLPE insulated, galvanised steel formed wire armoured (strip) cable 22 kV(E), 3 x 300 sq. mm. aluminium conductor laid in provided trench / pipe as per specification no. CB-HT

Sr No..381Supplying , erecting & terminating XLPE insulated galvanised steel formed wire armoured (strip) cable 22 kV(E), 3 x 95 sq. mm. aluminium conductor laid in provided trench / pipe as per specification no. CB-HT

Sr No..382Supplying, installing and testing earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm with funnel with a wire mesh for watering and brick masonry block C.I. cover complete with all accessories of G.I. materials & recording the results as per specification no. EA-EP

Sr No..383Supplying, installing and testing pipe type earthing with 40mm. dia. G.l. pipe or 20 mm dia. G.I. Rod complete with all accessories of GI materials & recording the results as per specification no. EA-EP

Sr No..384Supplying, installing and testing earthing with copper earth plate size 60 x 60 x 0.315 cm with funnel with a wire mesh for watering and brick masonry block C.l. cover with minimum 25 kg Carbon based environment friendly back fill ground ehancing compound complete with all accesories of copper materials & recording the results as per specification no EA-EP/EF

Sr No..385Supply, Installation, Testing and commissioning of maintenance free earthing comprising of Electrode of 17.2 mm diameter Low Carbon Steel with 250 micron molecular copper bonded earthing rod of Length 3m along with 25 kg Carbon based environment friendly back fill ground enhancing compound required to fill up the excavated earth with required quantity complete. Specification no. EA-MOBI

Sr No..386Supplying and erecting GI strip of required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with insulating and non-corrosive bond in an approved manner with required joints As per specification no. EAEP.

Sr No..387Supplying and erecting copper strip of required size used for earthing on wall and/or any other purpose with necessary copper clamps fixed on wall painted with insulating and non-corrosive bond in an approved manner with required joints As per specification no. EA-EP.

Sr No..388Supplying and erecting GI earth wire of high purity of different sizes used for earthing or any other purposes on wall with necessary G. I. Clamps fixed on wall/cable/ conduit with screws in an approved manner.

Sr No..389Supplying, erecting, testing and commissioning of diesel generating set with alternator of 320 kVA output continuous rating, 3 phase, 415 V, 50 Hz, 0.8 p.f., A.C. supply, a totally enclosed air cooled / liquid cooled multi-cylinder diesel engine developing suitable BHP at 1500 rpm with 10% overload for 1 hour in 12 hours, along with standard accessories, self-excited, self-regulated, screen protected alternator with static excitation system running at 1500 RPM as per IS 4722-2001 with voltage regulation +/- 5 %, with performance class G2/G3 and maximum fuel consumption 54.89 ltr/hr @75% loading. Both the engine and alternator direct coupled on a common fabricated steel base frame and mounted on anti-vibrating pads, with standard control panel comprising meters, switchgears, indicators connected with suitable wires/cables, the complete set enclosed in composite acoustic enclosure as fully assembled integral unit made of 16 SWG CRCA sheet, sound absorbing material to restrict sound level up to 75 dB at 1.0 m, provided with first filling of oil, diesel not less than 480 ltr etc., on provided M20 grade CC foundation and obtaining necessary approval from Electrical Inspector as per specification no. GEN-DG

Sr No..390Supplying, erecting, testing and commissioning of microprocessor based AMF panel suitable for Diesel generating set of above 250 kVA upto 320 kVA capacity 3 phase, 415 V, 50 Hz, A.C. supply with all standard features, safeties etc as per specification no. GEN-AMF.

Sr No..391Supply, installation, testing and commissioning of VRF/VRV based ceiling suspended 4 Way cassette room/indoor unit (IDU-compact / standard size) of nominal cooling capacity 3.3TR (1165 cfm) to 4.0TR (1218 cfm )having EER as per BEE standards and specifications, suitable as per site requirement with swing louvers and adjustable blades from sides. IDU with drainage arrangements, fan, refrigerant liquid and refrigerant piping, cordless remote control, and fresh air port etc. IDU shall have anticorrosive coating suitable for costal area in all respects suitable to operate on 1-phase, 230V, 50Hz, AC supply complete. The unit consisting with any additional refrigerant and oil charge as per requirement during installation.

Sr No..392Supply, installation, testing and commissioning of VRF/VRV based ceiling suspended 4 Way cassette room/indoor unit (IDU-compact / standardsize) of nominal cooling capacity 2.6TR (918 cfm) to 2.8TR ( 1100 cfm ) having EER as per BEE standards and specifications, suitable as per siterequirement with swing louvers and adjustable blades from sides. IDU withdrainage arrangements, fan, refrigerant liquid and refrigerant piping, cordless remote control, and fresh air port etc. IDU shall have anticorrosive coatingsuitable for costal area in all respects suitable to operate on 1-phase, 230V, 50Hz, AC supply complete. The unit consisting with

Sr No..393Supply, installation, testing and commissioning of VRF/VRV based ceiling suspended 4 Way cassette room/indoor unit (IDU-compact / standard size) of nominal cooling capacity 3.0TR (1100 cfm) to 3.2TR (1165 cfm) having EER as per BEE standards and specifications, suitable as per site requirement with swing louvers and adjustable blades from sides. IDU with drainage arrangements, fan, refrigerant liquid and refrigerant piping, cordless remote control, and fresh air port etc. IDU shall have anticorrosive coating suitable for costal area in all respects suitable to operate on 1-phase, 230V, 50Hz, AC supply complete. The unit consisting with any additional refrigerant and oil charge as per requirement during installation.

Sr No..394Supplying, erecting, testing and commissioning of 18HP, VRF/VRV air conditioning system outdoor unit (ODU) complies type-IV OEM standards working on HFC refrigerant R410A or other required/suitable green equivalent refrigerant, for minimum cooling capacity as delivering 100% capacity at 47° C, non stop cooling even at 56° C and coefficient of performance (COP) 3.00 to 4.00, modular type vertical hot air discharge suitable for longer piping range upto 1000 metre operation in cooling mode with inverter/ digital VRF/VRV technology microprocessor based control compressor starter/control panel with scroll compressor, air cooled copper condenser coil of suitable shape for increasing maximum heat transfer area, rain protection cover, built in oil separator, accumulator and oil receiver, copper tube aluminium fin air cooled condenser, condenser fan with motor suitable for 415V±10%, 50 Hz, 3 phase power supply (all suitable for high ambient conditions), internal copper refrigerant piping, internal wiring and refrigerant, etc. all housed in powder coated weather proof cabinet complete.

Sr No..395Supplying, installing, testing & commissioning split type variable speed inverter technology with minimum 3 to 1 convertible mode for compressor, room air conditioning unit 1.3TR to 1.6TR capacity having ISEER minimum 5.00 suitable to operate on 250V, 50 Hz, A.C. supply having 1 no of air handling unit hi-wall/floor mounting type complete with refrigerant R32 having copper condenser, minimum 2.5PM filter, self diagnosis feature, stabilizer free operation & temperature display on indoor unit, noise level maximum 50dBA at position as per specification no. AP-AC/ SAC

Sr No..396Supplying and installation of high pressure grade required size copper connection Y or T- Joints / refnet for liquid and suction line complete erected on wall/ceiling with supports/raceways, Nitrile rubber insulation, painting etc. with brazing and testing for leakages confirming the normal operation of the VRV / VRF air conditioning system.

Sr No..397Additional gas charging for the entire length of copper tube - Refrigerant R410A / Environmental friendly refrigerant.

Sr No..398Supply, Installation, Testing & Commissioning of armoured communication cables between outdoor units and indoor units and Indoor to Indoor units, ODU and Intelligent Touch Controller with PVC Conduit 1.5 sq.mm 2 core non-polarity cable

Sr No..399Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 10 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Sr No..400Power cabling between 3 Pin plug top and indoor unit 2.5 sq.mm 3 core copper flexible cable

Sr No..401Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 34.9 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system.

Sr No..402Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 28.6 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system.

Sr No..403Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 22.2 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system.

Sr No..404Supplying, erecting, testing & commissioning fresh air intake system, ductable circular inline fresh air fan inlet unit having 500 cfm capacity with maintaining the static ressure minimum 20 mm of Hg complete suitable to operate on 1ph, 230 V, 50Hz, A.C. supply.

Sr No..405Supplying, erecting, testing & commissioning fresh air intake system, ductable circular inline fresh air fan inlet unit having 1000 cfm capacity with maintaining the static pressure minimum 20 mm of Hg complete suitable to operate on 1ph, 230 V, 50Hz, A.C. supply.

Sr No..406Providing adhesive thermal insulation for supply / return air duct with 19 mm nitrile rubber insulation having R-value as per the prevailing provisions in ECBC- 2007.

Sr No..407Supply & laying of Hard PVC drain piping with elbow, bends, tees, clean outs etc with 9 mm Armaflex class 'O' insulation. For a)32 mm dia

Sr No..408Supply & laying of Hard PVC drain piping with elbow, bends, tees, clean outs etc with 9 mm Armaflex class 'O' insulation. For b)40 mm dia

Sr No..409Supply & laying of Hard PVC drain piping with elbow, bends, tees, clean outs etc with 9 mm Armaflex class 'O' insulation. Forc)50 mm dia

Sr No..410Providing & erecting hot dipped galvanised perforated type cable tray manufactured from 16 SWG GI sheet of 300 mm width & 75 mm height complete with necessary coupler plates & hardware.

Sr No..411Providing & erecting hot dipped galvanised perforated type cable tray manufactured from 16 SWG GI sheet of 400 mm width & 75 mm height complete with necessary coupler plates & hardware.

Sr No..412Supplying and erecting GI sheet 1 mm (20 SWG) to be used for fabrication of boxes panel boards etc. including cutting, bending, drilling, welding, riveting etc. and painting with one coat of red lead paint and 2 coats of enamel paint.

Sr No..413Supplying, erecting, testing & commisioning GI sheet 0.8 mm (22 SWG) having zinc coating of 275 microns with galvanization process compliance to IS 2629:1985 to be used for fabrication of boxes panel boards etc. including cutting, bending, drilling, welding, riveting etc. and painting with one coat of red lead paint and 2 coats of enamel paint as per specification no. CP/SH/CR

Sr No..414Supplying, erecting, testing & commisioning GI sheet 0.6 mm (24 SWG) having zinc coating of 275 microns with galvanization process compliance to IS 2629:1985 to be used for fabrication of boxes panel boards etc. including cutting, bending, drilling, welding, riveting etc. and painting with one coat of red lead paint and 2 coats of enamel paint as per specification no. CP/SH/CR

Sr No..415SITC OF 14 PASSENGER/952 Kg GEARLESS LIFT MR/MRL, COPO/ TOPO doors with frame having opening of 900 mm wide X 2000 mm high, Automatic Rescue Device, Audio- Visual, Overload indicator, Infra red curtain, 3VF drive, Emergency alarm, Fire alarm switch, overload warning indicator, suitable door safety as specified, suitable for physically challenged persons, complete in all respect as specified in technical specifications. The lift shall be provided with 3 year free defect liability period.SITC of Passenger gearless lift for 14 Passenger/952 Kg, G+6 floor (7Stops/7 Landings) Consider G+6 Rate due to More Height (23m)

Sr No..416Supplying, installation, testing and commissioning of 4.0 MP full HD video resolution 2560x 1440, 25 fps True D/N IR Bullet/ Box camera, 2.8-12 mm motorised lens, Auto Back Focus, High Light compensation, 120 dB and above True WDR, audio capture capability, 4 streams, H.264/H.265, ONVIF compliant,SD card Slot, with IP66 housing and mount with dehumidification feature with accessories such as mounting brackets/structures /fixtures etc. necessary to mount the camera on pole, etc. Video coding H.264 / H.265, Certification from EN, UL&CE,FCC. Tested in India from any reputed test laboratories/ Institute/ University/BIS for

Sr No..417Supply Installation Testing & commissionino Of Network Video Recorder 32 channel input, Support tch HDMI Up to 12 Megapixels resolution recording, Support RAID 0, I, 5, 6, I & 8 SAT A HDDs, Up to 8TB for each HDD, Supp01t N+ 1 Hot spare, Support for 12V Po~er output, HDMWGA Output, Recording Resolution, Resolution 12MP/ 6MP/5MP/4MP/3MP/I080p /960p/720p /Dl/2CIF/CIF, Compression H.265/H.264, 8 SATA interfaces, Capacity up to 8TB for each HDDs, Array Type RAID 0, 1, 5, 6, 10.

Sr No..418Supply Installation Testing & commissioning of 6000 GB Hard Disk for video Surveillance Equivalent to:- Western Digital.

Sr No..419Supply, installation, testing & commissioning of 4MP IP Dome/Bullet Camera with 1/2.8", progressive scan, CMOS, 2-8l4/6mm lens@ Fl.8/2.0, angle of view more than 82° WDR. 120db or above, Illumination Colour: 0.02 Lux (FI.8), 0.0Lux with lR ,Day/Night with auto switch ICR, ,supported H.264/H.265 MJPEG video compression ,Video triple Streaming,Smart function supported ( motion , IP 66 CE ROHS)

Sr No..420Supply, Installation,Testing & Commissioning of IP PTZ camera with HD1080P 2.1MP Resolution, 20x optical zoom, 16X Digital zoom , Day/Night, Wide dynamic range,Dual H.264 streaming, 0.05 lux, vandal resistant, 360° continuous pan, -5° to +95° tilt, 300 preset, 4 tours, IP66 rated with built in heater and blower, Mounted on Wall/Pole as per site requirement (including required accessories), UL listed as per detailed specifications. Camera Shall be ONVIF compliant

Sr No..421Supply Installation Testing & commissioning of 43 "TV Eauivalent to:- LG / Samsung.

Sr No..422Supply, Installation, Testing & commissioning of Hot dipped galvanised, round shape steel pole for installation of PTZ Camera and Outdoor Dome Camera, length 6 meters, diameter 4 inches (Nominal bore) Medium class, ISIS marked to IS:1239 with latest amdts and with atleast 1 Meter below ground with grouting.

Sr No..423SITC of 1IN/4OUT Video Splitter for additional viewing

Sr No..424S & i of 16CH NVR with 2 HDD bay

Sr No..425Supplying, fixing, and configuring 24 ports, PoE switch compliant with IEEE 802.3 standards with min. 193W PoE capacity with 4GE SFP uplink in provided rack as per specification no. WG-NWC/ENS

Sr No..426 Supplying & erecting UPS of 10KV A capacity complete with standard features, along with necessary SMF batteries for 20 mins. batterv backuo

Sr No..427Comprehensive Maintenance for Electric & CCTV Work : For 2nd Year @ 2.5%

Sr No..428Comprehensive Maintenance for Electric & CCTV Work : For 3rd Year @ 4%

Sr No..429Comprehensive Maintenance for Electric Work & CCTV : For 4th Year @ 5.5%

Sr No..430Comprehensive Maintenance for Electric & CCTV Work : 5th Year @ 7%

Sr No..431Supplying, installation, testing and commissioning of main fire pump (MFP /EP) suitable for water discharge of 2280 to 2850 LPM at 90 to 70 m head driven by electric motor 415 volts, 3 phase 50 Hz, AC supply of 55kW or of suitable kW capacity for manual/automatic operation and consisting of following : (a) Horizontal type, single stage, centrifugal/split casing pump of cast iron body & bronze impeller with stainless steel shaft (SS410 grade), mechanical seal conforming to IS 1520. (b) Squirrel cage induction motor, TEFC, synchronous speed 3000 RPM, suitable for operation on with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Erected on provided suitable size cement concrete foundation duly plastered with anti vibration pads with perfect aligning, proper levelling complete pump set with accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete, as per specification no. FF-MFP/SSC/EP

Sr No..432Supplying and erecting 150 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFV

Sr No..433Supplying and erecting 150 mm dia cast iron double flange NRV complete with PN16 pressure rating, as per specification no. FF-VL/NRV

Sr No..434Supplying and erecting G.I. pipe ‘C’ class ERW 150 mm dia with necessary fittings duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete as per specification no. FF-PP

Sr No..435Supplying and erecting 300 mm dia 1.5m in height air vessel / tank fabricated from min 5mm thick M.S. sheet complete as per specification no. FF-FFA/ACT

Sr No..436Supplying and erecting 12/15 mm dia pressure switch with provided isolation valve, G.I. nipple, elbow, etc complete as per specification no. FF-FFA/PS

Sr No..437Supplying, erecting testing and commissioning Multi Sensor (Smoke + Heat) detector with base on back box, necessary connections complete as per specification no. FF-FAS/MSD

Sr No..438Supplying, erecting testing and commissioning Optical Type Smoke Detector on suitable back box with necessary connections complete as per specification no. FF-FAS/SD

Sr No..439Supplying, erecting testing and commissioning Manual Call Point with break glass, push button (Resettable Type) in metal enclosure complete as per specification no. FF-FAAS/MCP

Sr No..440Supplying & erecting Carbon Dioxide (CO2) fire extinguisher of 4.5 kg. capacity cartridge type conform to IS 2878 /15683 complete erected with necessary clamp made from 50 x 6 mm. M. S. flat with nut & bolts routed in wall complete.

Sr No..441Supplying and erecting ABC powder type fire extinguisher as per IS : 13849 /15683 of 6 kg capacity with necessary clamp for erection on wall.

Sr No..442Providing Round bottom fire bucket of 9 Litres capacity as per IS : 2546 made out of 24 gauge G.I. sheet with extra handle at bottom duly painted white inside and red outside with FIRE Mark, on provided stand/ wall hook complete.

Sr No..443Supplying, erecting, testing and commissioning of Conventional Sounder cum Strobe rated at minimum 75 dB @ 3m for Audible annunciation and minimum 75cd flashing at 1 Hz for visual indication.. FF-FAAS/S-ST

Sr No..444Supplying, installing, testing and commissioning FR, XLPE armoured cable 2 core 1.5 sq.mm. copper conductor complete erected on wall/ ceiling complete as per specification no. CB-LT/CU

Sr No..445Supplying, installing, testing and commissioning FR, XLPE armoured cable 4 core 1.5 sq.mm. copper conductor complete erected on wall/ ceiling complete as per specification no. CB-LT/CU

Sr No..446Supplying & erecting Microphone table/floor stand with height 350-530 mm, base dia. min 150 mm, min. weight 1.8 kg with superior quality of chrome plating/powder coating (resistant to rust & corrosion) having sturdy mechanism for ensuring trouble free movement and positioning of microphone complete as per specification no. PA-MTS

Sr No..447Supplying, erecting, testing & commissioning Mixer Amplifier 120W RMS Power with Built-in MP3 player with remote control for USB, SD/MMC card reader, with min 5 Mic & 2 Aux Input, bluetooth facility, frequency response 50-15,000Hz ±3dB, Signal to noise ratio between 60dB to 65dB min 5 LED array for output level monitoring. It Shall have Line Output to connect a Booster Amplifier and Preamplifier Output. The Amplifier shall have Speaker Outputs - 4Ω, 8Ω, (Low Impedence) and 70V & 100V/(High Impedence), and can operate on 220-240V Power Supply & DC : 12V (facility to instant transfer

Sr No..448Supplying and erecting 63mm dia, reinforced rubber lined (R.R.L.) hose pipe, 15m in length, fitted with necessary accessories complete as per specification no. FF-FFA/RRL

Sr No..449Supplying and installing wall mounting swinging hose reel drum fitted with 19 mm dia. 30m long high pressure polypropylene (Polyhose) alongwith necessary accessories complete as per specification no. FF-FFA/HV

Sr No..450Supplying and erecting stainless steel branch pipe 63 mm dia fitted with 20 mm dia detachable hexagonal nozzle complete as per specifications no. FFFFA/ NZ

Sr No..451Supplying and erecting 100 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFV

Sr No..452Supplying and erecting stainless steel double outlet hydrant valve fitted with necessary accessories complete as per specification no. FF-VL/HV

Sr No..453Supplying and erecting G.I. pipe ‘C’ class ERW 150 mm dia with necessary fittings duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete as per specification no. FF-PP

Sr No..454Supplying and erecting G.I. pipe ‘C’ class ERW 200 mm dia with necessary fittings duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete as per specification no. FF-PP

Sr No..455Providing and fixing high-density polyethylene (HDP) container one piece moulded water tank made out of high density polyethylene and built corrugated inclusive of delivery up to destination hoisting and fixing of accessories such as inlet, outlet overflow pipe inclusive of all tanks capacity up to 20000 litres

Sr No..456Comprehensive Maintenance for Fire Fighting & Fire Alarm System Work : For 2nd Year @ 2.5%

Sr No..457Comprehensive Maintenance for Fire Fighting & Fire Alarm System Work : For 3rd Year @ 4%

Sr No..458Comprehensive Maintenance for Fire Fighting & Fire Alarm System Work : For 4th Year @ 5.5%

Sr No..459Comprehensive Maintenance for Fire Fighting & Fire Alarm System Work : 5th Year @ 7%

N A CONSTRUCTION PVT. LTD.