COMPREHENSIVE MAINT OF JCO/ OR ACCN AT D TOP UNDER GE DRONACHAL

Amount

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size n. exc 1.5 Sqm each and removing from site complete.

Taking down shutters of any description, area exceeding 1 sqm and not exceeding 2.00 sqm each complete.

Taking down shutters of any description, area exceeding 2 sqm each complete.

Supply and fixing 35 mm thick, 2nd class hard wood , glazed & skeleton factory made shutters, open rebated & prepared to receive glass, gauze etc. (without sash-bars), edges of framing plain, chamfered or rounded fitted with cut and metred beads for securing glass etc., sizes of members of shutters as specified in SSR Part-I, Section-8, clause 8.20(a) complete.

Supply and fixing 35 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides.

Supply and fixing solid PVC Door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, complete all as shown in drawing of relevant item in MES, schedule Part-II , 2004 as specified and as directed

Supply and fixing factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete all as shown in drawing of relevant item in MES, schedule Part-II , 2004 as specified and as directed

Supply and fixing Butt hinges, 100 mm long medium weight, cold rolled mild steel, ISI marked complete.

Supply and fixing aluminium handles extruded type of size 125mm, complete all as specified and directed.

Supply and fixing 150 mm long, aluminium anodised, barrel tower bolts, of extruded section ISI marked complete.

Supply and fixing 250 mm long aluminium alloy anodised sliding door bolt with hasp, staple and fixing clips of sheet cost or extruded sections or cost alumminium alloy

Supply and fixing galvanized mild steel wire-cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete .

Supply and fixing in repair 0.56 mm dia MS galvanised wire cloth with average width of aperature 1.18 mm and fixed with tinned tacks or galvanised wire staples, beads or in steel windows complete all as specified and directed.

Material and labour for Securing glass of any description in existing Metal/wooden frames glazed with putty/ beads including removing loose or decayed putty/ beads, painting/oiling one coat on rebates, grooves, reputtying and painting/oiling puttied surface to match existing work (New length of frame reputtied shall be measured) complete all as specified and as directed.

Supply and fixing 3 mm thick sheet glass ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sqm in each pane as incl removing of existing glass if required complete all as specified and directed.

Supply and fixing for figured glass, 3mm thick, pin head type and glazing with oil putty or beads in squares not exc. 0.50 Sqm in each pane as incl removing of existing glass if required complete all as specified and directed.

Supply and fixing in repair 300 mm, mild steel ordinary rat tail rod pattern spring including roller and roller plate complete all as directed.

Fixing with running welding in repair of ms hinges, helical door springs, rolling shutter spare parts heavy MS garrage doors etc. thickness of material n. exc. 6mm complete all as specified and as directed.

Supply and fixing in repair 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed all as specified and directed.

Supply and fixing in repair 200 mm long aluminium anodised barrel tower bolt of extruded section and fixed complete all as specified and directed.

Supply and fixing in repair 150mm long aluminium anodised barrel tower bolt of extruded section and fixed complete all as specified and directed.

Supply and fixing in repair aluminium handles 150 mm size, cast type, anodised complete all as specified and directed.

Supply and fixing in repair 140mm overall length of cover plate floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring with lower portion fixed with hard rubber, fixed in floor complete all as specified and directed.

Material and labour for Painting to new wood or wood based surfaces of any description not otherwise described over 10 cm in width or girth including preparation of surfaces, priming with pink primer (one coat) finished with two coats of synthetic enamel paint complete.

Supply and fixing in repair of steel window (with fly froof) with side hung shutter, incl projecting type hinges with steel handle, and steel peg stay, complete with glazing bars,dovetailed or welded complete all as specified and directed.

Supply and fixing in repair of steel ventilator (with fly froof) with top hung shutter, including hinges with steel handle, and steel peg stay, complete with glazing bars,dovetailed or welded complete all as specified and directed.

M&L for Mild steel work as in guard bars for window frames, L or T section supports for sheleves etc.and similar articals confirming to FE-290 GDE E-165 complete all as specified and directed.

Supply and fixing in repair 16 mm thick prelaminated particle board exterior grade,prelaminated side with decorative choice lamination& side balancing white lamination fixed with screws to timber frame work complete all as specified and as directed

Extra over rate for item No 28.00 above for prelaminated partical board for external teak wood lipping 6mm thick fixed with nails complete.

Material & labour in repair for 2nd class hard wood plain fillets, square, rectangular in section, making rebates for fixing prelaminated cupboard shutters clean sawn, secured with nails or brads in sectional area exc 13 & n. exc 25 sq. cm fixed with nails

Supply & fixing in repair Continuous (piano) hinges, mild steel, bright finish or electrogalvanised of width of flaps (when open) in 30mm

Supply and fixing in repair 40mm dia cupboard knobs fixed with nuts screws and washers of brass polished

Supply and fixing in repair ,4 lever Locks, cupboard, grade I, size 50 mm fixed with shutter with necessary cutting and fixing complete.

Supply and fixing in repair for 100 mm long Hasp and staple, aluminium anodised including bolt to hinge plate and fixed with screw as per specified.

S&F in reapir stainless steel 25mm dia pipe as in double bar curtain rods inclding brackets with fancy end knob wall to wall and complete, all as specified and directed

Supply and fixing in repair light coloured vitreous china wash hand basin white available shape as approved of 500mmx400mm (minimun) on new pre-painted brackets excluding taps but including 32 mm bore waste fittings, brass, chromium plated etc complete all as specified .

Supply and fixing in repair Vitreous China squatting pan “Orissa pattern” size 580x440mm white with integral foot rest (excluding flushing cistern and flush pipe) with CI ‘P’ trap of long arm of suitable size including connection to flush pipe, anti symphonic pipes and bed concrete etc complete

Supply and fixing in repair Vitreous China wash down water closet pan (Pedestal Pattern) and trap (standard pattern) coloured as approved including connection to drain (or outgoing pipe) and to flushing pipe anti symphonize pipe etc. including plastic water closet seat, white/black, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device and jointingcomplete with fixing bolts complete

Supply and fixing in repair Plastic water closet seat,any colour as available, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device and jointing complete.

Supply and fixingin repair PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets of 10ltrs capacity

Supply and fixing in repair of fancy type pillar taps cast copper alloy with capstan heads, chromium plated screwed down high pressure with or without lettered Hot or Cold with long screwed shank supply and fixing ly nuts for iron pipe of 15mm bore fancy type.

Supply and fixing in repairs of fancy type chromium plated Bib tap long body, 15mm bore any make as given in list of makes as directed by the GE.

Supply and fixing in repair of CP brass fancy type stop cock with long shank & as concealed type/ angular type complete all as specified and directed.

Supply and fix in repair PVC connection 15 mm size, of length 450 mm, with PTMT nuts complete.

Supply and fixing in repair PVC Flexible waste pipe 32/40 mm dia with socket for steel sink upto floor level and length not less than 0.60 M complete all as specified and directed.

Supply and fixing in repair of aluminium hat pegs, solid body, 125mm to 175 mm sets of 3 Nos peg set complete all as specified and directed.

Supply and fixing in repair aluminium hat pegs, solid body 175mm to 250 mm , peg sets of 6 Nos peg set of good quality complete all as specified and directed

Supply and fixing in repair brass chromium plated kitchen sink waste coupling comperising of four parts CP brass kitchen sink strainer & basket, rubber gasket, PTMT locknut, PTMT strainer sleeve with 32mm outlet and check of any dia as per site requirement complete all as specified and directed.

Supply and fixing in repair CPVC pipe 15mm dia of grade SDR-11 (class-I) including all CPVC and brass fittings fixed to walls, floors, or ceiling or laid in floors etc complete.

Supply and fixing in repair CPVC pipe 20mm dia of grade SDR-11 (class-I) ISI marked including all CPVC and brass fittings fixed to walls, floors, or ceiling or laid in floors etc complete.

S&F Tubular towel rail aluminium anodised 20 mm dia D-type 60 cm long between flanges, including brackets and fixed to walls, complete.

S&F in repair chromium plated shower roses 125 mm long with or without swivel joints, any size, including fixing fixing to steel pipe or union complete all as specified and direceted.

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15 cm thickness (below or above ground level ) complete.

Material and labour for 75 mm thick PCC 1:3:6 type C-2 (using 20 mm graded stone aggregate) as in plinth protection, surface finished even and smooth without using extra cement, laid in panels n exc 3 mtr long and joints shall be filled with the mixture of bitumen and sand in (1:3) by weight, complete all as specified and directed.

Material and labour 25 mm thick PCC 1:2:4 type B-1, using 20 mm graded stone aggregate, including finishing surface of concrete topping even and rough as in screed bed complete.

Demolition of stone slab and tiling of any description or thickness laid, bedded and pointed in any mortar

Material & labour for 20mm thick granite (of any type) work (table rubbed and polished)in steps, jambs, pillars, win dow-cills, cooking plat forms and like in cement mortar (1:4) including point ing in white cement (1:2) us ing marble dust with admix ture of pigment to matchwith shade of granite over and including 15 mm thick screed bed in Cement Mortar 1:6 complete all as specified and directed

Material and labour for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off premises complete.

Material and labour for glazed ceramic tiles coloured of size 350 x 450 x 7mm thick in walls etc, set & jointed in neat cement slurry and pointed in white or colours cement to match the colour of tiles over and including 10mm thick rendring in CM (1:4) complete all as specified and directed.

Material and labour Non skid coloured ceramic tiles 7 to 8 mm thick area of each tils exc.0.11 sqm but not exc 0.18 sqm in floor etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 15 mm thick screed bed in Cement Mortar 1:6 complete all as specified and directed

Cleaning and removing all scale and dirt etc from over head water tanks and from mouths of circulating pipe etc including dismantling & refixing at same or other place complete all as specified and directed by E-in Charge for following capacity including writing with oil paint the date of cleaning on tank ;

(a) Exc 250 Ltrs but not exc 500 Ltrs

Supply and fixing Rotational moulded polyethylene water storage tanks of 750 Litres capacity, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc & and 20mm ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball including taking down existing tank complete.

Supply and fixing 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe 15mm/20mm (using reducer) and fixed

Material and labour for sunken floor treatment as follows:-

(i) Demolition of cement concrete in sunken floors incl. removing dubrish outside MD land complete all as specified and directed.

(ii) Brushing neat cement slurry with 3.0kg of cement per sq. metre mixed with WPC @ 3% by weight of cement as per manufacturer's instruction to fill all hole and crack complete all as specified and as directed. Note:- Water tightness testing should be done after 24 hours

(iii) Material and labour for PCC (1:2:3) type B-0 using 12.5 mm graded stone aggregate with integral water proofing compound as per manufacturer instructions on bottom of sunken portion with proper slope towards spout and all pipe fixing.Note : Water proofing compound will be measured and paid separately.

(iv)Material and labour for plastering on vertical sides and top surface of CM (1:3) 15 mm thick mixed with water proofing compound as per manufacturer instructions. Plaster shall be extended over PCC coving when the same is green i.e. PCC & plaster be carried out at the same time. Note : Water proofing compound will be measured and paid separately.

(v) Material and labour for 2 coats of Dr. Fixit krystalline waterproofing coating compound shall be applied after laying sewage/ plumbing pipes with fixtures in position.

(vi)Material and labour for filling the sunken floor with PCC ( 1:5:10) type E-2 using bk aggregate over the treated surface.

(vii) Material and labour spouts of 50mm dia GI pipe light grade projecting 450mm clear of face outer wall with PVC mosquito proof cap on inner face of pipe shall be provided to drain out seepage water , if any.

Note : Water tightness testing should be done after applying Dr Fixit epoxy compound, by pounding water for 72 hours & rectify defects if any till total elimination of defect. Dubrish to be removed outside MD land.

M&L for Preparation of old decorated surfaces of wall including brooming , scraping down. Smoke spot, moss, efflorescent salts, trading oil, grasy spots and stopping nails marks by applying white cement base putty in patches as required and one coat of white wash on ceiling complete all as specified and directed.

M&L for Preparation of old decorated surfaces of wall including brooming , scraping down. Smoke spot, moss, efflorescent salts, trading oil, grasy spots and stopping nails marks by applying white cement base putty in patches as required and one coat of oil bound distemper all as specified and directed.

M&L for complete removal of old decorated surfaces of wall including brooming , scraping down. Smoke spot, moss, efflorescent salts, trading oil, grasy spots and stopping nails and applying two coat of oil bound distemper over & inculding a coat of white cement base putty compelet all as specified and directed.

M&L for Preparation of old painted surfaces of wood/wood based materials exc 10cm width or girth and applying one coat of synthetic enamel paint as directed and specified.

All as per item 69.00 above but on steel surfaces.

Taking down cement plaster of any description including raking out joints, hackisng for key, scrubbing down with water etc.

Material and labour for rendering 10 mm thick in cement and sand mortar 1:6 on fair faces of brick work or cement concrete surfaces finishing the surface even and smooth without using extra cement including preparation of newly plastered surfaces of walls and applying three coats of white wash complete.

-Ditto- all as per Srl item No.72.00 here-in-before, but 15mm thick in cement mortar 1:4 finished fair and even using integral waterproofing compound including Preparation of newly plastered surfaces of walls and applying two coats of cement base paint complete. Note:-Supply only of WPC shall be measured and paid separately.

Material and labour for rendering 5 mm thick in cement and sand mortar 1:4 on concrete surfaces of ceiling finishing the surface even and smooth without using extra cement including preparation of newly plastered surfaces of walls and applying two coats of cement base paint complete.

supply only integral water proofing compound

Material and labour for brickwork with sub class ‘B’ (old size) bricks, straight or curved on plan exceeding 6 metre mean radius built in cement sand mortar 1:6 including demolition & removing dubrish outside MD land complete all as specified and as directed .

Taking down carefully copper & aluminum point wiring for light, fan, socket or power complete and making good distrubuted surfaces of walls floors etc. Including switch & socket etc complete all as directed by EIC.

M & L for Point wiring using approved colour coding as per IS (Red, Black and Green for single phase circuits), with multi-stranded copper conductor 1.5 Sq. mm nominal cross-sectional area, single core, PVC insulated and unsheathed FRLS cable 1100 volts grade, ISI-694 marked with valid CML No. in and including medium grade, PVC concealed conduit and conduit accessories concealed in wall/roof/floor etc, ISI marked with valid CML No.(IS-9537-1983 for conduits and IS:3419:1976 for conduit accessories), with mild steel/pressed steel sunken boxes( with earth dolly) duly painted with two coats of anti corrosive paint/aluminium paint over a coat of red oxide primer internally, and two coats of black bituminous paint over a coat of red oxide primer externally, covered with 3 mm thick plastic laminated sheet cover for fixing of switches, sockets and fan regulators etc, including PVC insulated multi-stranded copper conductor 1.5 Sq mm nominal cross sectional area single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed at site for the following:-

One light/ceiling fan/exhaust controlled by one way switch.

One 3 pin socket outlet 5 Amps on independent board.

One 3 pin socket outlet on same board.

One light point controlled by two way switch.

S & F in repair of modular switch single pole one way 6 Amps, ISI marked complete all as directed by EIC.

S & F in repair of modular Socket single pole one way 6 Amps, 2 module ISI marked complete all as directed by EIC.

S & F in repair of modular switch single pole two way 6 Amps, ISI marked complete all as directed by EIC.

S & F in repair White cover plate with frame, 2 module ISI marked complete all as directed by EIC

S & F in repair White cover plate with frame, 3 module ISI marked complete all as directed by EIC

S & F in repair White cover plate with frame, 6 module ISI marked complete all as directed by EIC

S & F in repair Metal flush box 3 module ISI marked complete all as directed by EIC

S & F in repair Metal flush box 6 module ISI marked complete all as directed by EIC

M & L for Point wiring using approved colour coding as per IS (Red, Black and Green for single phase circuits), with multi-stranded copper conductor 4 Sq. mm nominal cross-sectional area, single core, PVC insulated and unsheathed FRLS cable 1100 volts grade, ISI-694 marked with valid CML No. in and including medium grade, PVC concealed conduit and conduit accessories concealed in wall/roof/floor etc, ISI marked with valid CML No.(IS-9537-1983 for conduits and IS:3419:1976 for conduit accessories), with mild steel/ pressed steel sunken boxes with earth dolly duly painted with two coats of anti corrosive paint/aluminium paint over a coat of red oxide primer internally, and two coats of black bituminous paint over a coat of red oxide primer externally, covered with 3 mm thick plastic laminated sheet cover for fixing of switches, sockets etc, including PVC insulated multi-stranded copper conductor 4 Sq mm nominal cross sectional area single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed at site for the one 3/5 pin 15/16 amps socket outlet independent.

S & F in repair incl making existing surface good sheet metal enclosures with socket plug top and MCB's with two pin and earth plug and socket complete with one single pole MCB 240 V grade 20 Amp.(AC Box) complete all as directed by EIC.

S & F of modular switch socket combination 16A (with gang box where is required), 6 pin, 3 module, ISI marked complete all as directed by EIC.

S & F in repair of switch piano type flush type single pole one way 5 Amps, ISI marked complete all as directed by EIC.

S & F in repair of socket outlet 5 pin flush 6 Amp multi pin 2/3 pin complete all as directed by EIC.

S & F in repair of switch socket combined outlet 6 pin flush 16 Amp multi, ISI marked complete all as directed by EIC.

S & F in repair of switch piano type/flush button type single pole two way 5 Amps front operated ISI marked complete all as directed by EIC.

S & F in repair of lamp holder , PVC/Poly carbonate type with back plate suitable for batten fittings complete all as directed by EIC.

S & F in repair of 3 pin plug top AC-230V, 6 Amp complete all as directed by EIC.

S & F in repair of 3 pin plug top AC-230V, 16 Amp complete all as directed by EIC.

S&F in repair ceiling rose, 3 phase/PVC/Polycarbonate, isolated body complete all as specified and directed by Engr-in- charge.

S & F in repair of High lam sheet cover ISI marked with required Nos of space for switches/Sockets/Regulator of size 250x280mm complete all as directed by EIC.

S&F LED Building security light fitting 1x 25 W new generation energy saving and environmental friendly long life made up of pressure die-cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP opening seprate driver compartment with IP 66 protection and impact resistance of IK07 for mounting existing bracket complete including all accessories pre-wired with 3 X 1.5 sqmm single core mutistrand copper conductor cable up to celing rose/ terminal box and proper earthing connection must be provided, all as directed by EIC.

S & F G.I. pipe house service bracket hook type shall be fabricated with 1.2 m long screwed G.I. pipe of medium quality and will comprise of two No. 90 to 120 degree (as required) bends (pipe dia 40 mm) screwed tight to the top ends of the service vertical limb, the two ends of the service shall be provided with two Nos. of turned spit tight fit, well seasoned teakwood bushings and the bracket shall be fixed plumb vertical against the wall with two Nos. flat iron clamps, including all connected items, complete all as directed by EIC.

Taking down existing U/S fittings any type any size and Supply & Fix LED 10 watt tube light fitting integrated type, (Length min 2 feet), 240 V, PF >0.90, colour temp 6500K, suitable for surface mounting on wall, multi stranded copper flexible cable 0.5 sqmm Two core, and PVC round block white colour x 2 Nos for mounting of fitting complete all as as directed by EIC.

S & F in repair incl taking down LED bulb 9 Watt with very high efficiency suited for installation in existing lamp holders, complete all as as directed by EIC.

S & F in repair 1 x 18 watt LED tube light fitting basic all purpose surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver, LED Decorative luminaire with suitable for lamps LED Light high efficiency LED driver,Optimized heat dissipation for ensuring high LED life span AC decorative box type with driver, holder including LED tube light connecting up with flexible copper conductor cable of suitable size from ceiling rose complete all as directed by EIC.

Taking down carefully aluminium sub main wiring from the existing casing/caping/PVC conduit all as diretced.

Material & Labour for sub main wiring with two run of 10 sqmm size PVC insulated multi stranded copper conductor FRLS cable (Nominal area) and one run of 10 sqmm size PVC insulated unsheathed stranded copper conductor cable drawn in either existing or new surface/ recessed steel/ PVC conduit/ PVC casing capping of required size complete all as directed by Engr-in-charge..

Material & Labour for sub main wiring with two run of 6 sqmm size PVC insulated multi stranded copper conductor FRLS cable (Nominal area) and one run of 6 sqmm size PVC insulated unsheathed solid core copper conductor cable drawn in either existing or new surface/ recessed steel/ PVC conduit/ PVC casing capping of required size complete all as directed by Engr-in-charge..

Material & Labour for sub main wiring with two run of 4 sqmm size PVC insulated multi stranded copper conductor fire retardanr cable (Nominal area) and one run of 4 sqmm size PVC insulated unsheathed solid core copper conductor cable drawn in either existing or new surface/ recessed steel/ PVC conduit/ PVC casing capping of required size complete all as directed by Engr-in-charge.

Earthing complete with galvanised iron earth plate electrode 60cmx60cmx6mm thick , burried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised steel wire 4 mm dia by means of galvanised nuts, bolts, check nuts and washers including excavation and earth work, PCC 1:3:6 type C-2 pit, PCC pit cover 1:2:4 type B-1 with handle, GI protection pipe 15 mm bore light grade and 20mm medium grade GI watering pipe, Funnel , wire mesh etc complete as shown in electrical Plate No.3 of SSR Part-I connected to earthing test point and metal part all as specified including testing on completion complete all as directed by EIC.

S&F sheet metal enclosure for VT DB TPN, MCCB DB TPN 4 way, with 200 A rated bus bar, double door with 100 Amp,25 KA,TP MCCB as incomer (Vertical type double door,100 Amps MCCB rate inclusive) and suitable for SP/TP DB in outgoing, enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP 43 including wooden rectangle board of first quality of suitable size for mounting of DB box with provision for 4 Pole MCCB* as incomer and SP/TP MCB as outgoings complete all as directed by EIC:

S & F in repair of MCB TPN 40 to 63 Amps, 415 V with thimble suitable for existing wires complete all as directed by EIC.

S & F in repair incl taking down sheet metal enclosure for MCB DB, SPN 230 Volts 200 amps rated busbar 8 way double door complete all as directed by EIC.

S & F in repair of MCB single pole with neutral 240 volts 25 to 40 Amps with thimble suitable for existing wires complete all as directed by EIC.

S & F in repair of MCB single pole 6 to 32 Amps 240 V with thimble suitable for existing wires complete all as directed by EIC.

S & F 125 A MCCB 4 pole, 16 kA breaking capacity, 415 V with suitable thimbles all as directed by EIC

Taking down ceiling fan/Exhaust fans/Wall mounting fan of any cap/sweep after disconnecting the electric supply from any site and opening fans for repair/over hauling including removing dust and greasing, and cleaning of blades and fan with kerosene oil and checking of alignment of shaft, oiling including re-assembling, nut bolt checking and connecting/refixing of fans in its original position burnt out fan shall be kept separately for rewinding complete all as directed by EIC. NOTE: Rewinding and replacement of defective parts shall be measured and paid seperately.

M&L for Rewinding ceiling fan of sweep 1200 mm/1400 mm with suitable gauge copper winding wire (super enamelled) including all insulating material after necessary heat varnishing testing etc. complete all as directed by EIC.

M&L for Rewinding Exhaust fan of sweep 250/300 mm with suitable gauge copper winding wire (super enamelled) including all insulating material after necessary heat varnishing testing etc. complete all as directed by EIC.

M&L for Rewinding Exhaust fan of sweep 380/450 mm with suitable gauge copper winding wire (super enamelled) including all insulating material after necessary heat varnishing testing etc. complete all as directed by EIC.

Note for Item No 116.00 to 118.00 1. Repairing/ rewinding of ceilling fan/ exhaust fan shall be carried out in the AGE E/M Dronachal subdivision in present of concern JE E/M. 2. Contractor shall detail the staff to collected defective fans from concern JE E/M, check the fans after opening it, and intimate the defects in the fan to JE E/M before carring out the repairs. 3. The bearing of fan should be of NBC/SKF make only. No other make will be accepted. 4. Contractor will be provided by stciker of each repairing fan with date and name of frms.

M & L for painting of following Item with two coats of DUCO paint (ISI grade) white using spray machine spray painting including cleaning, washing and preparation of old painted surfaces including MES Nos are Entered in all ceiling and Exhaust fan in site only, complete all as directed by Engr-in-Charge:- Note:- (painting shall be carried out in E/M Yard)

Ceiling fan of 1200/1400 mm sweep complete.

Exhaust fan of 300/380/450 mm sweep with smoke grey.

Geyser 25 liter cap.

S & F in repair metal fan blade of any type and any size suitable for 1200 mm/ 1400 mm Ceiling fan complete all as specified and directed by Engineer-in-Charge.

S & F in repair metal fan blade of any type and any size suitable for exhaust fan of any capacity, of any make, complete all as specified and directed by Engineer-in-Charge.

250/ 300/450 mm sweep

S & F ceiling fan regulator stepped type ISI marked, complete all as specified and directed by Engr-in-charge

S & F ceilling Fan down rod of size 15 mm GI pipe medium grade(ISI mark) length upto 50cm including making holes, nut bolts, spilit pin washers etc complete all as directed by EIC.

Taking out and replacement of following accessories form ceiling fans taking down vide item No 116.00 to 118.00 here in before complete all as directed by EIC.

Bearing No 6201

Bearing No 6202

Bearing No 6203

Rubber Bush , nut, bolts ,washer and split pin etc as reqd at site suitable for ceiling fan

Condenser 2.5 mfd

Condenser 4 mfd

Ceiling fan shaft

Ceiling fan clamps

S&F ceiling fan canopy for suitable of 1200/1400 mm sweep complete

M&L for Fixing of Geyser in existing or new position by providing suitable size of anchor fastner and connecting PVC flexible inlet and outlet pipe complete all as directed by EIC.

M&L for repairs to defective/leakage of geyser 25/50 ltr capacity inner tank of copper/Steel by brazing, soldering, gas welding including testing for leak proof upto the satisfaction of the EIC complete all as directed by EIC.

S&F Gun metal half turn UPVC gate valve of 25mm dia and fixed in position after taking out unserviceable gate valve complete all as directed by EIC.

S&F Gun metal half turn UPVC gate valve of 20mm dia and fixed in position after taking out unserviceable gate valve complete all as directed by EIC.

Taking down and dismantling the outer cover of geyser of any capacity and removing the scaling including repairing and replacement of the inlet and out let pipe and re-assembling the same after testing complete all as directed by EIC.

Taking out and repalcement of following unserviceable parts of Geyser :-

Inner tank stainless steel 25 ltrs cap ISI marked

Thermostat ISI marked

Triangle Heating element 1.5 KW/2 KW, ISI marked

Indicator lamp with flexibe copper wire of suitable size Red/Green

PVC Connection with steel reinforced pipe for hot water connection of Size 18" x 1/2"

S & F PVC insulated multi stranded Copper conductor, sheathed round cable ISI marked 1.5 sqmm x 3 core complete all as directed by EIC.

Replacement of burning wire of any size out of any type of existing TPN/SPN DBs including replacement of damaged PVC conduit with cement work complete .Note: Wire, PVC conduit and cement work includeed in quoted rate.

M & L for sheet metal enclosure with socket and plug top single pole & neutral with a two pin & earth plug & socket complete with one MCB SP 20 amps, 240 volts complete all as directed by EIC.

Material & Labour for sub main wiring with two run of PVC insulated multi stranded copper conductor fire retardant cable 4 sqmm size (Nominal area) and one run of PVC insulated unsheathed solid core copper conductor cable 4 sqmm size in including PVC casing capping flat pipe of required size complete all as directed.

S & F Stator for Ceiling Fan 1200/1400 mm sweep complete all as directed by EIC.

S & F rotor for Ceiling Fan 1200/1400 mm sweep complete all as directed by EIC.

Supply installation, testing and commissioning of Software Support and Sim Charges including software hosting, software AMC, GPRS Charges, RF network monitoring and troubleshooting and repair/replacement of meter/DCU with manufacturing defect for 134 meters in officers area complete all as specified and directed by Engr-in-charge. NOTE:- Contractor should sign the MoU with OEM for AMC

Samaksh Enterprises (BID ID -3135595)

PRAGATI ELECTRICALS AND ELECTRONICS (BID ID -3142585)

MODI CORPORATION (BID ID -3135727)