Remaining Work of Re-organization of Tandwa Rural Pipe Water Supply Scheme On Turnkey Basis Under DWSD CHATRA FY 2024 25 HEAD DMFT

Amount

Elevated Service Reservoir

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authorityand Providing all labours and equipment for designing & construction of ESR all complete job. (Please refer to Section 5,Sl. 2.8 of SBD)

ESR 6.50 Lakh Litre capacity with 24 Meter staging as per Design & Drawing (Zone -1 & 2)

ESR 1.35 Lakh Litre capacity with 24 Meter staging as per Design & Drawing(Zone -3)

Water Treatment Plant

Designing (aesthetically), providing and constructing high rate Unconventional Water Treatment Plant i.e. Simplified Water Treatment Plants consisting of Civil works including cost of Providing and applying Epoxy paint to inside surface of water retaining structures in contact with chlorine and providing anti - termite treatment to entire structure below Ground level, Mechanical and Electrical components of variours sub-works as given below : including necessary hydraulic testing, structural testing and trial run for 3 months, etc. complete as directed by Engineer-in-charge (turnkey job) works.

1. Aeration Fountain:

2. Inlet arrangements

3. Mixing channel with ventury flume and flow measuing arrangement

4. Inlet channel

5. Flocculator - Confirming to I.S. 7208-1974 (Type - C) with detention period of 30 minutes

6. Tube Settlers “Designing, fabricate and construct Tube Settlers with square or any other shaped tube like Circular, Cheveron, Hexagonal etc. having proven performance.”

7. Rapid sand gravity filters

8. Filter house

9. Chemical house

10. Alum tanks - 2 Nos. with mixing carrying and dosing arrangements with piping.

11. Gravity feed gas chlorinator with 100% standby. with 100% standby.

12. TCL solution tank with mixing, carrying and dosing arrangement with piping

13. Bye-pass arrangement

14. External and internal electrification for entire plant area.

15. Laboratory equipments

16. Wash water tanks of capacity equal to 12 minutes to wash specified number of filter beds at time at 600 lit/m2/m under head of 12 m at under drain

17. Wash water pumps with 100% standby

18. Air blowers capable of delivering 600 LPM per S.No. square metre of free air of filter area at 0.4 Kg/sqcm at the under drains (100%standby)

19. Pure water sump capacity equal to 1 hour pumping capacity

20. Pure water pump house over the sump / by the side of sump

21. Drainage arrangements

22. Alum store

23. Sanitary block with necessary water supply and drainage arrangement and internal WBM roads

24. These rates are applicable for seismic zones 2,3 and 4

25. Rates given below are inclusive of uplift pressure if any and dewatering during the entire work

26. All RCC structures shall be constructed in M-250. Structures in contact with water shall be in M-300.

27. Unconventoinal Treatment Plants less than 1 MLD capacity shall not be constructed.

Cost of 3.0 MLD WTP

Construction of R.CC intake well cum pump

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authorityand Construction of R.CC intake well cum pump 6.00 mm dia and 12.0 M deep & 5.00 M height pump chamber. Total height of intake well cum pump house will be 15.0 M (Please refer to Section 5,Sl. 2.1 of SBD)

Earthwork in excavation of foundation trenches of toe wall, spillway, head regulator, outlet, intake well etc. as per designed section in all kind of soil including moorum soil, soil mixed with kankar, pebbles & boulders upto 300m size & disposal of the same (beyond 50 m away from the edge of the trenches) with initial lead of 150 M & initial lift of 1.50M as per specification & direction of E/I.

Initial lift

1st lift

Earthwork in excavation of foundation trenches of toe wall, spillway, head regulator, intake well and outlet etc. as per designed section in ordinary rock or soft rock (where blasting is not needed) (Vide classification of Soil Item-C) with disposal of soil (beyond 50m from the edge of the trenches) with initial lead of 150 m & initial lift of 1.50m as per specification & direction of E/I

1st lift

2nd lift

Earthwork in excavation of foundation trenches of toe wall, spillway, head regulator, intake well and outlet etc. as per designed section in hard rock where blasting is needed and stacking properly in approved stack size in approved stack yard (beyond 50m from the edge of the trenches in country side) with initial lead of 150 m & initial lift of 1.50m as per specification & direction of E/I. (Excavated hard rock size should not be more than 150 lb)

2nd lift - 3.0 to 3.5 M :-

3rd lift - 3.5 to 4.5 M :-

4th lift - 4.5 to 5.5 M :-

5th lift - 5.5 to 6.12 M :-

Providing P.C.C.M-150 in nominal mix of (1:2:4) In foundation with approved quality of stone chips 20 mm to 6 mm size graded & clean coarse sand of F.M. 2.5 to 3 including screening, shuttering , mixing cement concrete in mixer & placing in position, vibrating, striking, curing, taxes & royalty all complete as per building specification & direction of E/I.

Providing and laying in situ Cement concrete of trap / granite / quartzite / gneiss metal for RCC work in foundation like raft, grillage, strip foundation and footing of RCC columns and steel sanchions including normal dewatering, plywood form work, bully/steel propups, compaction, finishing and curing, etc, complete. (By weigh batching and mix design for M-250 and M-300 only. (excluding M.S or Tor reinforcement).

Circular portion :-

Providing RCC M-250 in stiffners with approved quality of stone chips 20 mm to 6 mm size graded and clean coarse sand of FM 2.5 to 3.0 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing (but excluding the cost of reinforcement) taxes and royalty all complete as per building specification and direction of E/I.

Providing RCC M-250 in roof Slab (Pump House) with approved quality of stone chips 20 mm to 6 mm size graded and clean coarse sand of FM 2.5 to 3.0 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing (but excluding the cost of reinforcement) taxes and royalty all complete as per building specification and direction of E/I.

Providing and casting in situ Cement Concrete of trap/ granite/ quartzite/ gneiss metal of approved quality for RCC work as per detailed drawings and designs or as directed by Engineer-in-charge including normal dewatering, centering, 'plywood formwork, bully/steel prop-ups, compaction, finishing the formed surfaces with CM 1:3 of sufficient minimum thickness if special finish is to be provided and curing, etc. complete. (By weigh batching and mix design for M-250 and M-300 only. (excluding M.S, or Tor reinforcement)

Total Quantity of Slab:

Providing RCC M-250 in beam below P.H. roof of all types approved quality of stone chips 20 mm to 6 mm size graded and clean coarse sand of FM 2.5 to 3.0 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing (but excluding the cost of reinforcement) taxes and royalty all complete as per building specification and direction of E/I.

Providing and casting in situ Cement Concrete of trap/granite/quartzite/ gneiss metal of approved quality for RCC work as per detailed drawings and designs or as directed by Engineer-in-charge including normal dewatering, centering, 'plywood formwork, bully/steel prop-ups, compaction, finishing the formed surfaces with CM 1:3 of sufficient minimum thickness if special finish is to be provided and curing, etc. complete. (By weigh batching and mix design for M-250 and M-300 only. (excluding M.S, or Tor reinforcement)

Beam For P.H. floor

Providing R.C.C. M.-200 with nominal mix of (1:1.5:3) in stair case with approved quality of stone chips 20 mm to 6mm size graded and clean coarse sand of F M 2.5 to 3 including centering, shuttering, screening, mixing cement concrete in mixer placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/l

Providing R.C.C M-250 in band at lintel level and lintel with approved quality of stone chips 20mm to 6mm size graded & clean coarse sand of F.M. 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer & placing in position, vibrating, striking, curing (but excluding the cost of reinforcement), taxes & royalty all complete as per building specification & direction of E/I.

R.C.C. Band at lintel level

R.C.C.Lintel (Quantity as above total deduction)

Providing designation 75A brick work in C.M. (1:6) in superstructure with approved quality of clean coarse sand of F. M. 2 to 2.5 including providing 10 mm thick mortar joints, costs of screening, materials, scaffolding, ranking out joints to 15mm depth curing, taxes & royalty all complete as per building specification & direction of E/I. BCD 5.2.11

Providing average 63 mm thick R.C.C M-250 chajja with approved quality of stone chips 20mm to 6mm size graded & clean coarse sand of F.M 2.5 to 3 including making drip course in concrete, screening, centering, shuttering, & mixing cement concrete in mixer & placing in position vibrating, striking, 6mm cement plaster (1 :4) in ceiling & sides of chajja with sand of F.M 1.5 , curing (but excluding the cost of reinforcement) taxes, & royalty all complete as per building specification of E/I.

Providing 35 mm thick precast R.C.C.M -200 with nominal mix of (1:1.5:3) in shelves with approved quality of stone chips 20 mm to 6 mm size graded and clean coarse sand of F.M. 2.5 to 3 with 1.5 mm cement punning at top and side and 6mm cement plaster (1:4) at bottom including screening, curing and placing the slab in position (but excluding the cost of reinforcement) taxes and royalty all complete as per building specification and direction of E/l.

Providing 25mm thick pre cast R.C.C. M-150 with nominal mix of (1:2:4) Jali in ventilator with approved quality of stone chips of 6mm nominal size and clean coarse sand of F.M. 2.5 to 3 with 1.6mm thick M.S. wire as per approved design and drawing and placing the same in position true to plumb and level and properly grouted with cement mortar (1:3) including cost of curing, scaffolding and finishing, all complete, as per building specification and direction of E/I.

Providing 12 mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5 % Cico or any other water proofing compound including screening, curing with all leads & lifts of water, scaffolding, taxes & royalty all complete as per building specification & direction of E/I.BCD SOR NO 5.7.14

Extra for plaster work over exterior surface for each consecutive floor above first floor including cost of scaffolding etc. all complete as per direction of E/l.BCD SOR NO 5.7.20

1st lift

2nd lift

3rd lift

Providing 25 mm thick first class patent stone flooring (1:2:4) with stone chips in two layers, bottom layer 19 mm thick (1:2:4) with 12 mm to 6mm size graded stone chips and top layer 6 mm thick (1:2) with 6 mm down stone chips, in panels including cost of curing, finishing the surface smooth by rubbing with carborandum stone, taxes & royalty with all complete as per building specification & direction of E/I.BCD SOR NO 5.6.7

Total Quantity:-

Providing 12 mm thick cement plaster (1:6) on wall of P.H. with approved quality of clean coarse sand of F.M. 1.5 including screening, curing with all leads & lifts of water, scaffolding, taxes & royalty all complete as per building specification & direction of E/I.BCD SOR NO 5.7.3

Providing 6 mm thick cement plaster (1:4) in ceiling with approved quality of clean coarse sand of F.M. 1.5 including screening, curing with all leads & lifts of water, scaffolding, taxes & royalty all complete as per building specification & direction of E/I. DWSD SOR NO 5.7.6

Providing 1.5 mm neat cement punning in dado including curing carriage of water with all leads and lifts as per building specification & direction of E/I. BCD SOR NO 5.7.11

Supplying all materials, labours, tools & equipment and designing & making C.I. manhole cover of size 0.60m x 0.45m (Wt. 39 kg)duly approved by competent authority of the department with frame properly fixed on P.H. floor including cost of all taxes and transportation etc. all complete as per direction of E/I.DWSD SOR NO-ITEM NO 31 PG NO 38

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick top cover

Providing and fixing ball bearing for rolling shutters.

Supplying, fixing and fixing M.S grill made of 20x60 mm M.S flat as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specificaton and direction of E/I.BCD SOR NO 5.5.12

Providing Tor steel reinforcement of 8 mm dia. to 20 mm dia. Rods as per approved design & drawing excluding carriage of M.S rods (straight or in coils) to work site, cutting, bending & binding with annealed wire with cost of wire, removal of rust , placing the rods in position all complete as per building specification & direction of E/I. BCD SOR NO 5.5.5

Providing Pre Pack sieve bend made of statiless steel "V" Wire Screen (750mm x 750mm) with all complete work. This rate must be aproved by competant authority at the time of B.O.Q.DWSD SOR ITEM NO 154 Pg no 92

Supplying all materials, labour, tools, & hoisting, placing & fixing in position of R.S. joist including cost of cutting & straightening of the R.S. Joist to reacquired shape & size, supplying for fixing the chain pulley block all complete job as per the direction of E/I. BCD SOR ITEM NO 158+BCD SOR NO 5.5.26

Providing 2 coats of snowcem of approved shade and make over a coat of cement primer on new surface including preparing the plastered surface smooth with sand paper, curing, scaffolding & taxes all complete as per building specification & direction of E/I. BCD SOR NO 5.8.24

Providing primer one coat of read lead paint of approved make over new steel surface including preparing the surface after cleaning, removing rust, dirt’s, scales, smokes and grease and cleaning the surface thoroughly including cost of scaffolding and taxes all complete as per direction of E/I. (Mode of measurement:- area shall be multiplied by the co-efficient as indicated in building specification.)BCD SOR NO 5.8.41

Providing and fixing G.I. pipe railing having 1.0 M height consisting 50 x 50 x 6 mm thick M. S. angles as verticals at 1.5 M c/c, and additional posts at every corner with 3 rows of 25 mm dia G.I. pipes of medium class variety as horizontal and painting 3 coats of oil paint over 1 coat of anticorrosive paint of approved colour and shade including cost of all labour, transporting bends to curved shape, etc. complete.

Providing 2 (two) coats of synthetic enamel paints of approved shade & make over steel surface including cleaning the surface thoroughly, scaffolding & taxes all complete as per building specification & direction of E/I.BCD SOR NO 5.8.45

Providing, constructing coffer dam in river basin /dam storages as per type design including excavation, filling, the middle portion with B. C. soil (in gunny bags if requried). Providing impervious / semipervious materials on both side of B.C. soil (in gunny bags if required) including ramming, compacting to the satisfaction of Engineer-in-charge, till the complection of work including dismantling coffer dam after completion of works and disposing off the material as directed by the Engineer-in-charge.

Providing and fixing in position MS ladder 0.50 M wide consisting of 75 x 10 mm MS plats as stringers and 16 mm dia MS bars in double rows as steps placed at 25 cm c/c including cost of material and labour involved, welding, anchoring and applying 3 coat of anti corrosive paint, etc complete as directed by Engineer - in charge.

Dewatering the excavated trenches and pools to water by pumps & other devices

Supplying material and labour for fixing 20mm dia ms bar steps in stenning well of 0.3 m interval and staggred in (1:2:4) cement concrete including scafollding and curing etc of all complete as per specification and direction of E/I

Carriage of construction materials to work site including loading, unloading & stacking etc. all complete.

Cement 25 KM lead

Steel 25 KM lead

Sand 10 KM lead

Bricks 15 KM lead

Stone/Stone Chips 10 KM lead

weir & Tier of intake well

Construction of Gang Way 25 M long and 2.50 M wide

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authorityand Providing all labours and necessary equipment for designing & construction of Gang Way (Please refer to Section 5,Sl. 2.2 of SBD)

Earthwork in excavation of foundation trenches of toe wall, spillway, head regulator, outlet, intake well etc. as per designed section in all kind of soil including moorum soil, soil mixed with kankar, pebbles & boulders upto 300m size & disposal of the same ( beyond 50 m away from the edge of the trenches) with initial lead of 150 M & initial lift of 1.50M as per specification & direction of E/I.

Initial lift - 0 to 1.5 M

Earthwork in excavation of foundation trenches of toe wall, spillway, head regulator, intake well and outlet etc. as per designed section in ordinary rock or soft rock (where blasting is not needed) (Vide classification of Soil Item-C) with disposal of soil ( beyond 50m from the edge of the trenches) with initial lead of 150 m & initial lift of 1.50m as per specification & direction of E/I

1st lift - 1.5 to 2.0 M

Supplying all materials, labours & tools and doing P.C.C M-150 (1:2:4) with approed quality of stone metal grade III (50mm to 25mm size) clean coarse sand of F.M 2.5 to 3.0 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per specification and direction of E/I.

Providing and casting in situ Cement Concrete of trap/granite/quartzite/ gneiss metal of approved quality for RCC work as per detailed drawings and designs or as directed by Engineer-in-charge including normal dewatering, centering, 'plywood formwork, bully/steel prop-ups, compaction, finishing the formed surfaces with CM 1:3 of sufficient minimum thickness if special finish is to be provided and curing, etc. complete. (By weigh batching and mix design for M-250 and M-300 only. (excluding M.S, or Tor reinforcement) In foundation beem.

Providing and casting in situ Cement Concrete of trap/granite/quartzite/ gneiss metal of approved quality for RCC work as per detailed drawings and designs or as directed by Engineer-in-charge including normal dewatering, centering, 'plywood formwork, bully/steel prop-ups, compaction, finishing the formed surfaces with CM 1:3 of sufficient minimum thickness if special finish is to be provided and curing, etc. complete. (By weigh batching and mix design for M-250 and M-300 only. (excluding M.S, or Tor reinforcement)

In Pillars (400mm dia)

Providing and casting in situ Cement Concrete of trap/granite/quartzite/ gneiss metal of approved quality for RCC work as per detailed drawings and designs or as directed by Engineer-in-charge including normal dewatering, centering, 'plywood formwork, bully/steel prop-ups, compaction, finishing the formed surfaces with CM 1:3 of sufficient minimum thickness if special finish is to be provided and curing, etc. complete. (By weigh batching and mix design for M-250 and M-300 only. (excluding M.S, or Tor reinforcement) In Bracing & beem

M-200 in roof slab of Gangway nominal mix of (1:1.5:3) in Roof slab with approved quality of stone chips 20mm to 6mm size graded & clean coarse sand of F.M. 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer & placing in position, vibrating, striking, curing (but excluding the cost of reinforcement), taxes & royalty all complete as per building specification & direction of E/I.

Providing 12mm thick cement plaster (1:4) with clean coarse sand of F.M 1.5 including screening, curing with all leads and lifts of water scaffolding taxes and royalty all complete as per building specification and direction of E/I.

White washing three coats over new surface with approved quality of lime including cost of cleaning surface throughly and removing the scales of smokes and mosh marks with jhama rubbing, scaffolding, washing of floors and taxes all complete as per building specification and direction of E/I.

Providing and fixing G.I. pipe railing having 1.0 M height consisting 50 x 50 x 6 mm thick M. S. angles as verticals at 1.5 M c/c, and additional posts at every corner with 3 rows of 25 mm dia G.I. pipes of medium class variety as horizontal and painting 3 coats of oil paint over 1 coat of anticorrosive paint of approved colour and shade including cost of all labour, transporting bends to curved shape, etc. complete.

Providing M.S reinforcement as per approved design drawing including cost of cutting, bending, binding with annealed wire with removal of rust placing rod in posistion etc. all complete as per specification & direction of E/I.

Dewatering the excavated trenches and pools to water by pumps & other devices

Carriage of construction materials to work site including loading, unloading & stacking etc. all complete.

Cement 25 KM lead

Steel 25 KM lead

Sand 10 KM lead

Stone chips

Mechanical & Electrical Work at Intake Well

Supply, installation, testing and commisssioning of vertical turbine pumpsets with allied equipment as under (Please refer to Section 5,Sl. 2.4 & 2.6 of SBD)

Supplying. installation and commissioning of Vertical turbine water lubricated single / multi stage pump set of KIRLOSKAR / JYOTI /Mathar and Platt/WPIL make capable of required discharge against total roded head of 60 ft column accembly, 60 ft 10 ft long flange type havy duty M.S. coupled with suitable capacity vertical hollow shaft squirrel cage induction Motor of KIRLOSKAR / JYOTI /CGL / ABB / BHEL Marathon make operated on 415±10% Volt, 3 Phase, 50 C/S, A.C Supply having sutaible 1450 rpm (or suitable) with non reversible rachet, including Cost of supplying fitting and fixing of all required accessories such as D.l. D/F specials, sluice valve, N.R. valve, pressure gauge, strainer, M.S. Channel base, as required suitable fully automatic star delta starter ( FASD suitable for required) of L&T/Jyoti/ Siemens / Schineder make, foot valve lSI maked and Dl. D/F pipe of suitable size and length as required for suction and delivery main etc. all complete, (Contractor will once again have to check the design of motor, Pump & he will have to get it approved by the Deptt. (Pump & Motor) (all complete as per site required).

Discharge 34.50 lps with 35 Mtr. Head

Supply, Installation and Commissioning of Power control cum cubical panel board (MCC), made of 2 mm thick, MS sheet of suitable size, dust and vermin proof consisting of following accessories.

a) Incoming feeder-TPN MCCB 200 A thermal release range, adjustable and breaking capacity with rotary operating mechanism handle (front drive) of make L&T/ SIEMENS/ Havells/ HPL - 1no.

b) Outgoing feeder- 415V TPN MCCB 100A having thermal release range, and breaking capacity with rotary operating mechanism handle (front drive) of make L&T/SIEMENS/ HPL/ ALSTOM/ Havells - 2no.

c) Bus Bar- 4 pole 315A copper strip bus bar enclosed in MS sheet, etc. all complete job- 1no.

f) Indicating lamp LED - L&T/SIEMENS make in Red, Yellow and Blue colour- 1set.

g) 32A MCB for light load & other loads of L&T/ Havells/ Alstom / HPL - 2no.

h)100A MCCB as spare of L&T/ Havells/ Alstom /HPL (for Pump set) - 1 no.

Panel should be duly painted with two coats super enameled paint of approved colour one coat of red oxide primer and internally wired with suitable size of copper control wire/cable, etc. all complete. (Including their control cables and as shown in the attached diagram) capacitor or APFC Panel to be provided for desired p.f. of 0.96, etc. all complete. As per site requirement & IE rule.

Supplying fitting and commissioning of switch disconnecting isolator (TPN) rated current 315A-415V

Supplying and erection and Cost of earthing of installation as per I.E. Rules including the cost of earth pit and 8 SWG copper wire in bunch of two and G.Ipipe all complete to all instrument. ( with Charcoal + Salt )

Supplying triple spur gear type chain pulley block suitable for 3 tone lifting capacity with 6 m lift complete with load chain and hand chain suitable for above lift, tested to 50% of over load as per IS 3832 carrying ISl mark.

Supplying XLPE/PVC insulated, armoured cable 1.1 KV grade with ISI mark Three and half core, stranded aluminium conductor with 6 mm thick 25 mm width M.S. spacer with G.I. Earth wire complete in an approved manner. (3.5 core x 120 Sq mm cable including laying on wall or on floor as and where required from LT line from transformer to panel of Raw water pumping plant)

Supplying XLPE/PVC insulated, armoured cable 1.1 KV grade with ISI mark Three and half core, stranded aluminium conductor with 6 mm thick 25 mm width M.S. spacer with G.I. Earth wire 6 sq. mm, complete in an approved manner. (3.5 core x 25 Sq mm cable including laying on wall or on floor as and where required from LT line from transformer to panel of Raw water pumping plant)

Cost of providing Electric Wiring in side and out side the pump house for lighting including cost of LED Lamp of 120W,DB, all types of fittings etc all complete Including fire extingusher first aid box, gloves, tools tackles etc all complete as per direction of E/I.

(Mechanical & Electrical Part at WTP)

Suply, installation, testing and commisssioning of horizontal casing centrifugal pumpsets with alied equipment as (Please refer to Section 5,Sl. 2.5 & 2.6 of SBD)

Suplying, installation, and commisssioning of Horizontal Split Casing / End Suction suitable centrifugal pump set of Kirloskar / Jyoti / WPIL / Mather & Platt make capable for rated discharge against total rated head and mounted of common base plate coupled with SPDP/ TEFC squirrel case suitable capacity induction motor by tyre coupling of Kirloskar / ABB / Jyoti / SIEMENS/ Crompton Greaves/ MARATHAN/ BHEL make operated on 415 volt +- 10%, 3 phase 50 Hz. A.C supply having suitable 1480 rpm including cost of supplying fitting and fixing of all required accessories such as C.I. D/F Sluice valve, C.I. D/F NR valve, C.I. D/F pipe, foot valve ISI mark and CI D/F pipe of suitable size and lenght as required for suction and delivery main etc. all complete including cost of supplying, erecting and commissioning fully automatic star delta starter [make: L&T / Jyoti / Siemens / Schneider] of suitable size for required motors etc. all complete as per site requirement including foundation making (Contractor will again check the design of pump & Motor and get approved by the Dept.)

Discharge 28.68 LPS, Head 42 m 25HP (1W+1S) For Zone 1 & 2

Discharge 5.85 LPS, Head 66.40 m - 10 HP (1W+1S) For Zone 3

Supply, Installation and Commissioning of Power control cum cubical panel board (MCC), made of 2 mm thick, MS sheet of suitable size, dust and vermin proof consisting of following accessories.

a) Incoming feeder-TPN MCCB 315 A thermal release range, adjustable and breaking capacity with rotary operating mechanism handle (front drive) of make L&T/ SIEMENS/ ALSTOM / Havells/ HPL - 1no.

b) For each pump sets Outgoing feeder- 415V TPN 63 A and 32A MCCB OL having thermal release range, and breaking capacity with rotary operating mechanism handle (front drive) of make L&T/SIEMENS/ HPL/ ALSTOM/ Havells -4no.

c) Bus Bar- 4 pole 315A copper strip bus bar enclosed in MS sheet, etc. all complete job- 1no.

f) Indicating lamp LED - L&T/SIEMENS make in Red, Yellow and Blue colour- 1set.

g) 32A MCB for light load & other loads of L&T/ Havells/ Alstom -2no.

h) 63A MCCB as spare of L&T/ Havells/ Alstom (for Pump set) - 1 no.

(i)63A & 32A as sparer feeder for Pump sets - 1 no each.

(j) 200A power feeder for Intake well Pumps -1 no.

(k) Panel should be duly painted with two coats super enameled paint of approved colour one coat of red oxide primer and internally wired with suitable size of copper control wire/cable, etc. all complete. (Including their control cables and as shown in the attached diagram) capacitor or APFC Panel to be provided for desired p.f. of 0.96, etc. all complete. As per site requirement & IE rule.

Supplying, erection and Cost of earthing of installation as per I.E. Rules including the earth pit and 8 SWG copper wire in bunch of two and pipe all complete in all equipments (with Charcoal + Salt ) for all motor.

Supplying triple spur gear type chain pulley block suitable for 3 tone lifting capacity with 6 m lift complete with load chain and hand chain suitable for above lift, tested to 50% of over load as per IS 3832 carrying ISl mark etc all complete.

Supplying XLPE/PVC insulated, armoured cable 1.1 KV grade with ISI mark Three and half core, stranded aluminium conductor with 6 mm thick 25 mm width M.S. spacer with G.I. Earth wire 6 sq. mm, complete in an approved manner. (3.5 core x 185 Sq mm cable including laying on wall or on floor as and where required from LT line from transformer to panel of clear water pumping plant)

Supplying XLPE/PVC insulated, armoured cable 1.1 KV grade with ISI mark Three and half core, stranded aluminium conductor with 6 mm thick 25 mm width M.S. spacer with G.I. Earth wire 6 sq. mm, complete in an approved manner. (3.5 core x 50 Sq mm cable including laying on wall or on floor as and where required (from Panel to motor)

6 Sq mm cable ( Zone III )

16 Sq mm cable ( Zone I & II )

Raw Water Rising main.

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authorityand Laying of Raw water Rising Main (Please refer to Section 5,Sl. 3.0 of SBD)

Providing and supplying ISI mark centrifugally cast (spun) Ductile iron pressure pipes of 300mm and above all diameter for water works with socket and Spigot ends conforming to IS 8329/2000 in standard working lengths of 4.5, 5.5 & 6.0 M for classification K-9 suitable for push-on-joint (Rubber gasket D jointing ) with cement morter lining inside the pipes with outside Zinc and bituminous coating including all other taxes, insurance etc. all complete

200 mm dia Pipe (K9)

Carriage of DI pipe (400 km lead)

200 mm dia Pipe (K9)

A ) Earth work in excavation (As per IS. 3114/1965) for laying of different types and sizes of pipes so as to give one meter average cover over the socket of pipe with disposal of excavated earth within initial lead and lift as per specification and direction of Engineer in charge DWSD SOR NO 3.1.1.1 soil item B

B) E/W in excavation of cut off trenches as per design section in soft rock or ordinary rock (where blasting is not needed) (vide classification of soil item-C with disposal of spoil (beyond 50M away from the toe of dam in country sode) with initial lead of 150M and lift of 15M, including making the section in profile, dressing sides in proper slope and bed in proper grade etc. all complete as per specifictaion and direction of E/I SOR NO WRD 7.1.12.2

Earth work in backfilling the trenches after lying of different types and sizes of pipes with earth removed during excavated within initial lead and lifts as per specification and direction of Engineer in charge.DWSD SOR NO 3.1.1.2

Supplying labours, tools, tackles, lubricant etc. for laying and jointing D.I/C.I. S/S tyton pipes (class LA) trenches supplying rubber gasket conforming to I.S.S - 5382-1969) and making gasket joint including providing night guard, barrier and red light to safe guard against accident, all complete ( pipe to be supplied departmentally free of cost and laying of pipe is to be done as per I.S.S 3114-1985 as per deisgn, specification and direction of E/I.DWSD SOR NO 3.1.32(b)

200 mm dia pipe

Providing and supplying air valve as per IS-14845-2000 and MJP's standard specification of approved make & quality of following diameters including all taxes ( central and local), railway freight, insopection charges, unloading from railway wagons, loading into truck, transportation upto departmental stores / sites unloading and stacking etc. complete.depatmental.PN 1.6 single ball

50 mm dia pipe

Lowering, laying and fixing in proper alignment and position all type of C.I air valves as directed by engineer in charge including cost of conveyance from store to site of work, cost of all materials and giving satisfactory hydraulic testing etc. comlete. PN 1.6 single ball

50 mm dia pipe

Providing Double Flanged Sluice valve (Size 50mm to 1200mm) for scour, confirming to IS 2906/14846 including worn gear arrangements as per test pressure stainless steel spindle, caps including all taxes transportation etc. complete.without DWSD SOR NO123(C) Page no 63

200 mm dia pipe

Supplyng labour and tools for fixing sluice valve in trenches with a pair of C.I Tail pieces incluidng making lead caulked joints and flenged joints as per I.S specification, including supplying all jointing materials (Pig lead confirming to I.S.S 782-1978, yarn confirming to I.S.S 6587-1972 and nuts and volts confirming to I.S.S 1364-1983) including drillig holes in flanges if required as per specification and direction of E/I.DWSD SOR NO 3.1.35

200 mm dia pipe

Supplying tools and tackles for testing of laid D.I pressure pipe up to 60 mm meter head of water all complete as per specification and direction of engeneer- in- charge. Water to supplied free of cost departmentally. DWSD SOR NO 3.1.46

200 mm dia pipe

Labour cost for one cutting of D.I /C.I Pipes & specials including supplying, necessary tools and plants, chipping or filling the surface finish as per spercification and direction of E/I.DWSD SOR NO 3.1.43

200 mm dia pipe

Providing and supplying ISI standard D.I specials & fitting with sealing rubber gasket of S.B.R complete with cast iron follower gland and M.S nut & bolts coated or otherwise protected from rusting and suitable for D.I pipes including ED, CST, all taxes, etc. complete as per I.S-9523 but excluding freight.DWSD SOR NO S-111 Pg 44

Supplying all labours, tool & equipments for cutting pucca or W.B.M road and restoring the same after laying & jointing of pipe lines. Total Road Cutting Area.

i) Pucca Road DWSD SOR NO 3.1.19.1(a)

ii) W.B.M RoaddDWSD SOR NO 3.1.19.1(b)

Dismentaling plain cement or lime concrete work including stacking servicable materials in countable stacks within 15 meter lead and sisposal of unservicable materials with all leads all complete as per direction of E/I.BCD SOR NO 5.10.2

Providing PCC M-150 in nominal mix of (1:2:4) in foundation with approved quality of stones chips 20 mm - 6mm size graded and clean coarse sand FM 2.5 to 3.0 including screening shuttering mixing cmenet concrete in mixer and placing in position vibrating striking curing taxes and royalty all complete as per building specification and direction of E/IBCD SOR NO 5.3.1.2

Supplying all materials, labours, tools and equipment and constructing brick masonry chamber of 1.20M.x 0.90M. x 1.50M. inner size having 25cm. thick 75A brick masonry wall in C.M. (1:6), over 150mm. P.C.C. M- 150, laid over one brick flat soling on 100mm. local sand filling, including 12mm. thick cement plaster with punning of inner surface and exposed surface of B/W in C.M. (1:6) and R.C.C. M- 150 cover slab 150mm. thick with 20mm. to 6mm. graded stone chips, and clean coarse sand of F.M. 2.5 to 3 including providing CI surface box and screening shuttering, mixing, placing, striking, curing, taxes and royalty all complete as per approved design, drawing & specification and direction of E/I.

Supply all materials & construction of Thrust Block of RCC M - 200 with nominal mix of (1:1.5:3) in foundation and plinth with approved quality of stone all complete job as per specification and direction of E/I.(200 mm )

Clear Water Rising main.

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authorityand Laying of Clear water Rising Main (Please refer to Section 5,Sl. 3.0 of SBD)

Providing and supplying ISI mark centrifugally cast (spun) Ductile iron pressure pipes of 300mm and above all diameter for water works with socket and Spigot ends conforming to IS 8329/2000 in standard working lengths of 4.5, 5.5 & 6.0 M for classification K-9 suitable for push-on-joint (Rubber gasket D jointing ) with cement morter lining inside the pipes with outside Zinc and bituminous coating including all other taxes, insurance etc. all complete

100 mm dia Pipe (K9)DWSD SOR NO ITEM 110

200 mm dia Pipe (K9)

Carriage of DI pipe (400 km lead)

100 mm dia Pipe (K9)

200 mm dia Pipe (K9)

A ) Earth work in excavation (As per IS. 3114/1965) for laying of different types and sizes of pipes so as to give one meter average cover over the socket of pipe with disposal of excavated earth within initial lead and lift as per specification and direction of Engineer in charge

B) E/W in excavation of cut off trenches as per design section in soft rock or ordinary rock (where blasting is not needed) (vide classification of soil item-C with disposal of spoil (beyond 50M away from the toe of dam in country sode) with initial lead of 150M and lift of 15M, including making the section in profile, dressing sides in proper slope and bed in proper grade etc. all complete as per specifictaion and direction of E/I.

Earth work in backfilling the trenches after lying of different types and sizes of pipes with earth removed during excavated within initial lead and lifts as per specification and direction of Engineer in charge.

Supplying labours, tools, tackles, lubricant etc. for laying and jointing D.I/C.I. S/S tyton pipes (class LA) trenches supplying rubber gasket conforming to I.S.S - 5382-1969) and making gasket joint including providing night guard, barrier and red light to safe guard against accident, all complete ( pipe to be supplied departmentally free of cost and laying of pipe is to be done as per I.S.S 3114-1985 as per deisgn, specification and direction of E/I.DWSD SOR NO 3.1.32(a)

100 mm dia pipe

200 mm dia pipe

Providing and supplying air valve as per IS-14845-2000 and MJP's standard specification of approved make & quality of following diameters including all taxes ( central and local), railway freight, insopection charges, unloading from railway wagons, loading into truck, transportation upto departmental stores / sites unloading and stacking etc. complete.depatmental.MJP SOR NO section I (xii)5B

25 mm dia pipe

40 mm dia pipe

Lowering, laying and fixing in proper alignment and position all type of C.I air valves as directed by engineer in charge including cost of conveyance from store to site of work, cost of all materials and giving satisfactory hydraulic testing etc. comlete. MJP SOR NO-section I (xiX)19

25 mm dia pipe

40 mm dia pipe

Providing Double Flanged Sluice valve (Size 50mm to 1200mm) for scour, confirming to IS 2906/14846 including worn gear arrangements as per test pressure stainless steel spindle, caps including all taxes transportation etc. complete.DWSD SOR NO 123C Pg no 63

100 mm dia pipe

Supplyng labour and tools for fixing sluice valve in trenches with a pair of C.I Tail pieces incluidng making lead caulked joints and flenged joints as per I.S specification, including supplying all jointing materials (Pig lead confirming to I.S.S 782-1978, yarn confirming to I.S.S 6587-1972 and nuts and volts confirming to I.S.S 1364-1983) including drillig holes in flanges if required as per specification and direction of E/I.dwsd sor no 3.1.35

100 mm dia pipe

Supplying tools and tackles for testing of laid D.I pressure pipe up to 60 mm meter head of water all complete as per specification and direction of engeneer- in- charge. Water to supplied free of cost departmentally.DWSD SOR NO 3.1.46

100 mm dia pipe

200 mm dia pipe

Labour cost for one cutting of D.I /C.I Pipes & specials including supplying, necessary tools and plants, chipping or filling the surface finish as per spercification and direction of E/I.DWSD SOR NO 3.1.43

100 mm dia pipe

200 mm dia pipe

Providing and supplying ISI standard D.I specials & fitting with sealing rubber gasket of S.B.R complete with cast iron follower gland and M.S nut & bolts coated or otherwise protected from rusting and suitable for D.I pipes including ED, CST, all taxes, etc. complete as per I.S-9523 but excluding freight.

Supplying all labours, tool & equipments for cutting pucca or W.B.M road and restoring the same after laying & jointing of pipe lines. Total Road Cutting Area.

i) Pucca Road

ii) W.B.M Road

Dismentaling plain cement or lime concrete work including stacking servicable materials in countable stacks within 15 meter lead and sisposal of unservicable materials with all leads all complete as per direction of E/I.

Providing PCC M-150 in nominal mix of (1:2:4) in foundation with approved quality of stones chips 20 mm - 6mm size graded and clean coarse sand FM 2.5 to 3.0 including screening shuttering mixing cmenet concrete in mixer and placing in position vibrating striking curing taxes and royalty all complete as per building specification and direction of E/I

Supplying all materials, labours, tools and equipment and constructing brick masonry chamber of 1.20M.x 0.90M. x 1.50M. inner size having 25cm. thick 75A brick masonry wall in C.M. (1:6), over 150mm. P.C.C. M- 150, laid over one brick flat soling on 100mm. local sand filling, including 12mm. thick cement plaster with punning of inner surface and exposed surface of B/W in C.M. (1:6) and R.C.C. M- 150 cover slab 150mm. thick with 20mm. to 6mm. graded stone chips, and clean coarse sand of F.M. 2.5 to 3 including providing CI surface box and screening shuttering, mixing, placing, striking, curing, taxes and royalty all complete as per approved design, drawing & specification and direction of E/I.

Supply all materials & construction of Thrust Block of RCC M - 200 with nominal mix of (1:1.5:3) in foundation and plinth with approved quality of stone all complete job as per specification and direction of E/I.(100 mm)

DISTRIBUTION MAIN(DWSD M-1026)

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authorityand Providing all labour, materials, equipment to procure and laying of DI class K-7 pipes with Cement Mortar Lining for distribution main (Please refer to Section 5,Sl. 3.0 of SBD)

Providing and supplying ISI mark centrifugally cast (spun) Ductile iron pressure pipes of 100mm and above all diameter for water works with socket and Spigot ends conforming to IS 8329/2000 in standard working lengths of 4.5, 5.5 & 6.0 M for classification K-7 suitable for push-on-joint (Rubber gasket D jointing ) with cement morter lining inside the pipes with outside Zinc and bituminous coating including all other taxes, insurance etc. all complete DWSD M-1026

(i) 100 mm dia pipe

(ii) 150 mm dia pipe

(iii) 200 mm dia pipe

(iv) 250 mm dia pipe

(v) 300 mm dia pipe

(vi) 350 mm dia pipe

Carriage of DI pipe (400 km lead)

(i) 100 mm dia pipe

(ii) 150 mm dia pipe

(iii) 200 mm dia pipe

(iv) 250 mm dia pipe

(v) 300 mm dia pipe

(vi) 350 mm dia pipe

A ) Earth work in excavation (As per IS. 3114/1965) for laying of different types and sizes of pipes so as to give one meter average cover over the socket of pipe with disposal of excavated earth within initial lead and lift as per specification and direction of Engineer in charge (Classification soil item B) - 70% of excavated earth.DWSD SOR NO 3.1.1.1

B) E/W in excavation of cut off trenches as per design section in soft rock or ordinary rock (where blasting is not needed) (vide classification of soil item-C with disposal of spoil (beyond 50M away from the toe of dam in country side) with initial lead of 150M and lift of 15M, including making the section in profile, dressing sides in proper slope and bed in proper grade etc. all complete as per specifictaion and direction of E/I.

Earth work in backfilling the trenches after lying of different types and sizes of pipes with earth removed during excavated within initial lead and lifts as per specification and direction of Engineer in charge. DWSD SOR NO 3.1.1.2

Supplying labours, tools, tackles, lubricant etc. for laying and jointing D.I/C.I. S/S tyton pipes (class LA) trenches supplying rubber gasket conforming to I.S.S - 5382-1969) and making gasket joint including providing night guard, barrier and red light to safe guard against accident, all complete ( pipe to be supplied departmentally free of cost and laying of pipe is to be done as per I.S.S 3114-1985 as per deisgn, specification and direction of E/I. DWSD SOR NO 3.1.32

(i) 100 mm dia pipe

(ii) 150 mm dia pipe

(iii) 200 mm dia pipe

(iv) 250 mm dia pipe

(v) 300 mm dia pipe

(vi) 350 mm dia pipe

Providing and supplying ISI standard D.I specials & fitting with sealing rubber gasket of S.B.R complete with cast iron follower gland and M.S nut & bolts coated or otherwise protected from rusting and suitable for D.I pipes including ED, CST, all taxes, etc. complete as per I.S-9523 but excluding freight.DWSD ITEM NO-111 PG NO 44 (class k12)

Providing Double Flanged Sluice valve (Size 50mm to 1200mm) for scour, confirming to IS 2906/14846 including worn gear arrangements as per test pressure stainless steel spindle, caps including all transportation etc. all complete DWSD ITEM NO 123(B) Pg no 62(without bypass PN-1)

Supplyng labour and tools for fixing C.I sluice valve in trenches with a pair of C.I Tail pieces incluidng making lead caulked joints and flenged koints as per I.S specification , including supplying all jointing materials (Pig lead confirming to ISS 782-1978, yarn confirming to IS.S 6587-1972 and nuts and volts confirming to I.S.S 1364-1983) including drillig holes in flanges if required as per specification and direction of E/I.DWSD SOR NO 3.1.35

Supplying all labours, tool & equipments for cutting pucca or W.B.M road and restoring the same after laying & jointing of pipe lines. Total Road cutting area

Pucca road-

W.B.M Road-

Dismentaling plain cement or lime concrete work including stacking servicable materials in countable stacks within 15 meter lead and sisposal of unservicable materials with all leads all complete as per direction of E/I.

Providing PCC M-150 in nominal mix of (1:2:4) in foundation with approved quality of stones chips 20 mm - 6mm size graded and clean coarse sand FM 2.5 to 3.0 including screening shuttering mixing cmenet concrete in mixer and placing in position vibrating striking curing taxes and royalty all complete as per building specification and direction of E/I.

Supplying all materials, labours, tools and equipment and constructing brick masonry chamber of 1.20M.x 0.90M. x 1.50M. inner size having 25cm. thick 75A brick masonry wall in C.M. (1:6), over 150mm. P.C.C. M- 150, laid over one brick flat soling on 100mm. local sand filling, including 12mm. thick cement plaster with punning of inner surface and exposed surface of B/W in C.M. (1:6) and R.C.C. M- 150 cover slab 150mm. thick with 20mm. to 6mm. graded stone chips, and clean coarse sand of F.M. 2.5 to 3 including providing CI surface box and screening shuttering, mixing, placing, striking, curing, taxes and royalty all complete as per approved design, drawing & specification and direction of E/I.

Labour charges for one cutting DI-K7 including supplying necessary tools & plants as per specification. DWSD SOR NO 3.1.43

100 mm dia pipe

supplying tools and tackles for testing of laid D.I pressure pipe up to 60 mm meter head of water all complete as per specification and direction of engeneer- in- charge.DWSD SOR NO 3.1.46

(i) 100 mm dia pipe

(ii) 150 mm dia pipe

(iii) 200 mm dia pipe

(iv) 250 mm dia pipe

(v) 300 mm dia pipe

(vi) 350 mm dia pipe

Providing, installing and giving satisfactory field testing of flanged ends Bulk water meter of following type and as mentioned below with FGI-250 cast iron body class"B" confirming to IS : 2373 or as per ISO-4064/4046, marked to read in metric system, alongwith manufacturer's test and guarantee certificate including cost of all materials and labour with ISI mark or EEC mark.

(a) EEC mark Removable mechanism type (suitable for remote reading attachement) as per ISO 4046

1) 100 mm dia

2) 150 mm dia

carriage of material

construction of thrust block

Twin Type Staff Quarter - 1 Unit (Please refer to Section 5,Sl. 2.7 of SBD)

E/W in Excavation in foundation trenches in ordinary soil (Vide classification of soil Item -B) & disposal of excavatd earth obtained to a distance up to 50 M including all lift leveling ramming the foundation trenches removing root of trees scrubs all complete as per approved design.

Providing ,coarse clean sand in filling in foudation trenches /in Plinth including ramming & watering in layers not exceeding 150 mm thick with all leads lift including cost of all materilas ,labour , royalty & taxes all complete as per building specification & direction Of E/I

Providing designation 75 A one brick flat soiling joints filled with local sand including cost of watering taxes royalty all complete as per building specification & direction of E/I

Providing P.C.C M-100 in nominal mix of (1:3:6) in foundation with appoved quantity of stone metal (50 mm 25 mm dia size)graded & clean coarse sand of F.M 2.5 to 3 including screening , shuttering , mixing cement concrete in mixer & placing in position , vibrating , striking , curing taxes & royalty all complete as per building specification & direction of E/I

Providing designation 75 A brick work in C.M. (1:6) in foundation 7 Plinth with approved quality of clean coarse sand of F.M 2 to 2.5 including Providing 10 mm thick mortar joints ,Cost of screening , materials , Scaffolding , raking out joints to 15 mm depth curing , taxes & royalty all complete as per building specification & direction of E/I

Providing 25 mm thick damp proof coarse with cement concrete M-150 with nominal mix of (1:2:4) with approved quality of stone chips of 20 mm to 6 mm size graded and clean coarse sand of F.M 2.5 to3 including screening , shuttering mixing cement concrete in mixer with 5% cico or any other approved water proffing compound and placing in position , vibrating , striing , curing , taxes & royalty all complete as per building specification & direction of E/I

Providing designation 75 A brick work in C.M (1:6) in super structure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing10 mm thick motar joints ,cost of screening , materials, scaffolding,raking out joints to 15 mm depth curing , taxes & royalty all complete as per building specification & direction of E/I

Providing R.C.C M-150 with nominal mix of (1:2:4) in lintel level with approved quality of stone chips 20 mm to 6mm size graded & clean coarse sand of F.M 2.5 to including screening , centring, shuttering and mixing cement concrete in mixer & placing in position vibrating striking curing (but excluding the cost of reinforcement ) taxes & royalty all complete as per building specification of (E/I.

Providing average 63 mm thick R.C.C M -150 with nominal mix (1:2:4) chajja in shelves with approved quality of stone chips 20 mm to 6 mm size graded & clean coarse sand of F.M 2.5 to 3 including making drip course in concrete , screening , centering shuttering & mixing cement concrete in mixer & placing in position vibrating ,striking ,6 mm cement plaster (1:4) in celling & sides of chajja with sand of F.M 1.5, Curing ( But excluding the cost of reinforcement ) taxes and royalty all complete as per building specification of E/I

Providing R.C.C M-200 with nominal mix of (1:1.5:3) in roof slab with approved quality of stone chips 20 mm to 6 mm size Graded & Clean coarse sand F.M 2.5 to including making drip course in cocrete , screening , concreting , shuttering , centring mixing cement concrete in mixer & placing in position , vibrating ,striking, curing (but excluding the cost of reinforcement) taxes & royalty all complete as per building Specification & direction of the E/I

Supplying fitting & fixing good quality ,well dressed & well seasoned sal wood work in choukhat in doors , windows , skylights , fan light and C/W celestial windows openings , including wedge over all clamps complete including application of two coats of wood preservative of approved quality on the surface butting walls & lintels all complete as per building specification & direction of E/I

Supplying fitting and fixing 250X20X6 mm L-type M.S Clamp properly fish tailed .including making holes and setting the same in 375 X125X75 mm cement concrete block (1:2:4) with cost of all labour and materials and taxes as per building specification and diection of E/I @6 for each door & 4 for each window Total Quantity -(2X3X6+2X4X4)=68 nos

Supplying all materials , labours and fitting & fixing 38 mm (1.5) thick good quality seasoned sal wood battened shutter ledged & braced in door and windows with oxidized iron fitting such as hingles ,sliding door bolts , tower bolts , handles or ings hooks and eye , cleats , sand block as per schedule , taxes & royalty all complete as per building specification & direction of Engineer -in- charge

Supplying , fittings & fixing M.S /Gril made of 20X6 mm M.S flat as per approved design & drawing properly fabricated with joints continous filllet welded and finshed smooth , carriage of grill to work site hoisting as per the building specification and direction of E/I ( where materials is not supplied by the Deptt .)

Providing 25 mm thick pre cast R.C.C M-150 with nominal mix of (1:2:4) in jali with approved quality to stone chips of 6mm nominal size and clean coarse sand of FM 2.5 to 3 with 1.6 mm thick M.S wire as per approved design and drawing and placing the same in position true to plumb and level and properly grouted with cement mortar (1:3) including cost of curing , Scaffolding and finishing all complete as per building specification and direction E/I

Providing and fixing fan hook of 16 mm dia M.S bar 1 meter long bent to reqired size and shape placed in position and fixing in R.C.C slab/beam at the time of casting all complete as per building specification of E/I where material is not supplied by cheet

Supplying , fitting and Fixing M.S Grill gate made of 20X 6 mm M.S or 16 mm M.S raurbar Flat fitted on 25 mm X 25 mm X 6mm M.S angle frame of size 60X60X6 as per approved design including cost of fabrication & drawing , properly fabricated with joints continuous fillet welded & finished smooth, providing necessary locking arrangements with Haskell & dummy duly fixed in C.C (1:2:4) blocks of reuired size applying a priming red lead paints over steel works , taxes , carriage of grill to work site , asper the building specification & direction of E/I ( where materials is not supplied by the Dept)

Providing 6 mm thick cement plaster (1:4) in celling with approved quality of clean coarse sand of F.M 1.5 including screening , curing with all leads & lifts of water , scaffolding , taxes & royalty all complete as per building specification & direction of E/I

Providing 12 mm thick cement plaster (1:6) with approved quality of clean coarse sand of F.M 1.5 including screening .Curing with all leads & lifts of water , Scaffolding , taxes 7 royalty all complete as per building specification & direction of E/I.

Providing cement 1:3 (12mm ) plaster with cement mortar (1:3) using clean coarse sand finishing with neat punning a dado 6" (150 mm) high a side room and out side wall upto plinth level includng screening , curing with all leads & lifts of water , scaffolding , taxes and royalty all complete as per building specification & direction of E/I

Earth work in filling in foudation trenches & Plinth in layers not exceeding 150 mm thick well watered ,rammed ,fully compacted & fine dressed with earth obtained from excavation of foundation trenches within a lead of 50 m & lift of 1.5 m all complete as per building specification & direction of E/I ( Mode of measurement compacted volume)

Providing 25 mm thick . First class patent stone flooring (1:2:4) with stone chips in two layers ,bottom layer 19 mm thick (1:2:4) with 12 mm to 6 mm size graded stone chips and top layer 6 mm thick (1:2) with 6 mm down stone chips in pannels including cost of curing , finishing the surface smooth by rubbing with carborandum stone taxes & royalty with all complete as per building specification & direction of E/I

Providing designation 75 A one brick on edge flooring in C.M (1:4) with top surface flush pointed in CM (1:4) approved quality of clean coarse sand of F.M 2 to 2.5 including the cost of screening ,raking out joints to 15 mm depth , curing taxes,royalty all complete as per building specification and direction (E/I)

White washing three coats over new surface with approved quality of lime including the cost of cleaning surface thoroughly and removing the scales & mosh marks with jhama rubbing, scaffolding washing of floors and taxes all complete as per building specification and direction of E/I.

Color washing two coats over a coat of white wash over new surface with approved quality of lime in approved shade including the cost of cleaning surface thoroughly and removing the scales & mosh marks with jhama rubbing, scaffolding washing of floors and taxes all complete as per building specification and direction of E/I.

Providing two coats of synthetic enamel paint of approved shade and make over new wooden surface including cleaning the surface after removing dirt, scales, smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification & direction of E/I

Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning , removing rust ,dirt ,scales ,smokes and grease and cleaning the surface thouroughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I

Providing two coats of synthetic enamel paint of approved shade & make over steel surface including cleaning the surface thoroughly, scaffolding & taxes all complete as per building specification & direction of E/I.

Providing for steel reinforcement of 8 mm dia as per approved design and drawing excluding carriage of bars to work site ,cutting, bending and binding with annealed wire with cost of wire removal of rust placing the rods in position all complete as per Specification and direction of E/I.TMT Fe 500 (Only valid for SAIL and TATA )

Carriage of materials from divisional store or kiln site or quarry site to work site including contract profit, loading, unloading, transportation, etc. all complete .

Cement 25 KM lead

Steel 25 KM lead

Sand 10 KM lead

Bricks 15 KM lead

Stone/Stone Chips 10 KM lead

As per DPR water supply sanitary installation & sewarge system

Supplying and laying GI pipes of approved make in trenches with red lead and yarn with socket and screw joints and cutting pipes in size and threading ends where necessary including carriage of materials up to work site etc. all complete as per specification and direction of E/I.

i) 25mm GI. Pipe.

ii) 15 mm GI. Pipe.

Supplying materials and labours for fixing GI Pipes with red lead paints and yarn with screwed and sockted joints on wall, celling and floor including supplying of wall hooks of pipe clamp, wooden plugs, cutting pipe to size and threading ends where necessary all complete as per specification and direction of E/I.

i) 15 mm GI. Pipe

Supplying, fitting and fixing of GM ferrule of approved make in DI/CI main including drilling and tapping CI/DI main etc. all complete as per specification and direction of E/I.

Supplying and fixing GI fittings of approved make all complete as per direction of E/I.

(a) Elbow 15 mm dia

(b) Tee plane 15mm dia

(c) Nipple 15mm dia.

(d) Union Socket 25mm dia

(e) Union Socket 15mm dia

(f) Brass bib cock 15mm dia

(g) C.I stop cock 15mm dia

(h) C.I. stop cock 25mm dia

(i) Reducing Socket 25x15mm

(j) Tee 25x25x15mm dia

Supplying, fitting and fixing vitreous white glazed earthen were I W C of parry Hindustan or any other I.S.S approved make with 100 mm HCI ‘P’ trap, 15 Liters CI pull and let go flushing cistern of names or other ISS equivalent make complete with all fittings C.I. or C.C brackets, 32 mm, alkathene /PVC telescopic flush pipe about 2 mtrs. long with one brass coupling and clamps, GI chain and pull including supplying and fixing a pair of vitreous white glazed earthen were footrest to be fixed in floor, 15 mm .CI body brass spindle, stop cock of weight not less than 50 grams, 15 mm. PVC connection pipe 450 mm. long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/I. (510mm.long with 12.5 Liter low level PVCSystem).

SEPTIC TANK and SOAK PIT

Earth work in excavation in foundation trenches in ordinary soil (vide classification of soil item-B) and disposal of excavated earth as obtained to a distance up to 50 m including all lifts, leveling, ramming the foundation trenches, removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/I.

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials, labours, royalty and taxes all complete as per building specification and direction of E/I.

Providing designation 75A one Brick flat soling, joints filled with local sand including cost of watering, tax, royalty all complete as per building specification and direction of E/I.

Providing P.C.C M150 with nominal mix of (1:2:4) in foundation with approved stone chips 20mm to 6mm size well graded and clean course sand of FM-2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, Vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing water proof cement plaster (1:3) with clean course sand of F.M- 1.5mm with 5% cico or any other approved water proofing compound including taxes and royalty all complete as per building specification and directions of E/I.

(a) 19 mm thick

(b) 12 mm thick

Providing designation 75A bricks work in C.M. in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm. thick mortar joints, cost of screening materials racking out joints to 15 mm. depth, curing taxes and royalty all complete as per building specification and direction of E/I.

(a) B/W in C.M (1:4)

(b) B/W 75-B in (1:6) for Soak pit

(c) Brick work in dry masonry for soak pit.

Providing pre cast R.C.C. M-150 with nominal mix of (1:2:4) slab of desired size with approved quality of stone chips and clean coarse sand of FM 2.5 to 3 including curing, shuttering, carrying the slab manually to site and laying in position all complete (but excluding the cost of reinforcement), taxes and royalty etc. all complete as per building specification and direction of E/I.

Providing for reinforcement as per approved design and drawing excluding carriage of tor rod to work site including cutting bending and binding with annealed wire with cost of wire removal of rust placing the rods in position all complete as per Specification and direction of E/I.

10 mm dia

Supplying fitting and fixing H.C.I. Pipe/ H.C.I. fitting of Approved make confirming to I.S.S 1729 including supplying nails and bobbins lead and yarn from making lead caulked joints including earth work or providing scaffolding as the case may be all complete as per specification and direction of E/I.

(a) 100mm dia H.C.I. Tee.

(b) 100mm dia H.C.I. Band

(c) 50mm dia H.C.I. Cowel

(d) 50mm dia H.C.I. Vent pipe

(e) 100mm H.C.I. Pipe

Supplying materials and labours and fixing 20mm dia M.S bar steps in wall of 0.3 m interval and staggered in (1:2:4) cement concrete including scaffolding and curing etc. all complete as per specification and direction of E/I.

Supplying all materials, labours, tools and tackles and 100mm dia R.C.C hume pipe and laying jointing, testing, earth work including carriage of materials etc. all complete.

Supplying 50mm size brick bats and filling in soak pit including carriage and labours etc. all complete as per direction of E/I.

Supplying materials and labours for constructing inspection chamber of designation class 75 B bricks size 750mm deep, 600x450mm internal dimension having 250mm wall thickness in cement mortar (1:6) including 12mm cement plaster (1:4) with punning on inside and cement plaster (1:6) with 600x475 mm G.I. Cover With frame ( Weight not less than 36 Kg.) along with earth work in excavation and 80mm thick P.C.C. (1:3:6) in foundation and refilling all complete as per specification and direction of E/I

Carriages of materials

(a) Brick –15 KM lead

(b) Sand -10 KM lead

(c) Stone chips -10 KM lead

(d) Steel 25 KM

(d) Cement- 25 KM lead

As per DPR electric connection

Point wiring in PVC conduit with modular type switch wiring for light point /fan point with 1.5 sqmm F.R. PVC insulated copper conductor single core cable in surface/recessed PVC conduit with modular switch modular plate, suitable G.I. box and the point with sqmm FR PVC insulated copper conductor single core cable etc as required

Wiring for twin control light point with 1.5 sqmm F.R. PVC insulated copper conductor single core cable in surface/recessed PVC conduit with two way modular switch modular plate, suitable G.I. box and the point with sqmm FR PVC insulated copper conductor single core cable etc as required

Wiring for light /power plug point with 2 x 4 sqmm F.R. PVC insulated copper conductor single core cable in surface/recessed PVC conduit along with one no 4 sqmm FR PVC insulated copper conductor single core cable for loop earthing etc as required

Copper sub main wiring in PVC conduit Wiring for sub main wiring with PVC insulated copper conductor single core in surface/recessed PVC conduit as required

2 x 1.5 sqmm + 1 x 1.5 sqmm earth wiring

2 x 2.5 sqmm + 1 x 2.5 sqmm earth wiring

Supplying and fixing following way three pole and neutral sheet MCB distribution board 415 volts on surface/recessed complete with tinned copper bush bars ,neutral link, earth bar, din bar, detachable gland plate inter connection phosphatised and power painted including earthing etc as required (but with out mcb / rccb / Isolator) (4 +12 ) double door horizontal type

Supplying and fixing 5 amp to 32 amp, rating 240 volts, B series miniature circuit breaker of single poles in existing MCB DB complete with connecting ,testing, and commissioning etc as required

Earthing with G.I. earth pipe 4.5 M long 40mm dia including accessories and providing masonry enclosure with copper plate having locking arrangement and watering pipe etc with charcoal ,salt all complete as per electrical rule

Supplying ,fitting and fixing following sizes of PVC conduct along with accessories in surface / races including cutting the wall and making good the same in case of recessed conduit as required

PVC con 20 mm PVC pipe

PVC con 25 mm PVC pipe

Installation commissioning and testing Ceiling Fan

Carriage of ceiling fan and regulator

Supplying ,fitting and fixing 5 amp ceiling rose on the existing junction

Supplying ,fitting and fixing breas batten/ angle holder including connection etc.

Supplying ,fitting and fixing G.I. box with modular plate and cover in front of surface or in recess including providing and fixing 3 pin 5/6 amp modular type switch, connection, painting etc as required.

Supplying ,fitting and fixing G.I. box with modular plate and cover in front of surface or in recess including providing and fixing 6 pin 5/6 amp and 15/16 amp socket outlet and 15/16 amp modular type switch, connection, painting etc as required.

Supplying and drawing co-axial T.V. cable RG-06 grade 0.7 nn solid copper conductor PE insulated seilded with fine tinned cover braid and protected with PVC sheath in the existing surface / recessed steel/ PVC conduit as required.

Supplying and fixing modular switch / socket on the existing modular plate and switch box including connection but excluding modular plate etc,as required. TV antenna socket out put

Supplying ,fitting and fixing modular base and cover plate on existing modular metal boxes etc as required.

Cost of Earthing with G.I. earth pipe 4.5 M long 40mm dia G.I.Pipe 600mm x 600mm x 6mm thick copper earth plate, and 8 SWG copper wire including cost of making 1.2x1.2x3m deep pit and filling with charcoal ,salt all complete as per electrical rule

Compound Wall/ Boundry Wall for WTP & ESR. (300 M Long)

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authority Construction of Compound wall. etc. all complete job.(Please refer to Section 5,Sl. 2.9 of SBD)

Earthwork in excavation in foundationtrenches in Ward soil (vide classification of soil item-A)disposal of excaveted earth as obtained to a distance upto 50 mincluding all lift levelling ramming the foundation trenches removing roots of trees, shurbs all complete as per approved design building specification and direction of E/I.

Providing coarse clean sand in filling in foundation trenches or in plinth includingrall materials, labour, royalty and taxes all complete as per building specificationand direction E/I. (Mode of measurement compacted volume)

Providing designation 75 A brick flat soling jointsfilled with local sand including cost of watering taxes royalty all completeas per building specification and direction of E/I.

Providing PCC M100 with nominal mix of (1:3:6) in foundation with approved quality of stone metal grade-iii(50 mm to 25 mm size) clean coarse sand of FM 2.5 to 3 including sceening,shuttering mixing cement concrete in mixer and placing in position, vibrating, stricking, curing taxes and royalty all complete as per building specification and direction of Engineer in charge.

Providing designation 75 A brick work in CM (1:6) in foundation and plinth with approved quality of clean coarse sand of FM 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing R.C.C.M - 150 in band at plinth level with approved quality of stone chips 20 mm to 6mm size graded and clean coarse sand of F.M. 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing (but excluding the cost of reinforcement) taxes and royalty all complete as per building specification and direction of E/l.

Providing designation 75 A brick work in CM(1:6) in super structure with approved quality of clean coarse sand of F M 2 to 2.5 including providing 10mm thick mortar joints.cost of screening materials raking out joints to 15mm depth,curing,taxes and royalty all complete as per building specification and direction of E/I.

Providing R.C.C M - 150 with nominal mix of (1:2:4) in band at lintal level with approved quality of stone chips 20 mm to 6mm size graded and clean course sand of F.M 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/I.

(ii) Centering & shuttering etc all complete

Providing R.C.C M - 150 with nominal mix of (1:2:4) in stiffners with approved quality of stone chips 20 mm to 6mm size graded and clean course sand of F.M 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing , taxes and royalty all complete as per building specification and direction of E/I.

(ii) Centering & shuttering etc all complete

Providing M.S reinforcement as per approved design drawing including cost of cutting, bending, binding with annealed wire with removal of rust placing rod in posistion etc. all complete as per specification & direction of E/I.

Supplying, fitting and fixing M.S. grill gate with M.S. grills made of 20x6mm M.S. flats or 16mm square bars fitted on 25x25x6mm M.S Angle frame including cost of fabrication , providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size, applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/l.

Cost of 50 x 50 x 6 mm M.S. Angle including all taxes and royalty and carriage as per specification and direction of E/I.

Cost of Barbed wire of 4 point 2 ply 12 SWG ,150 mm apart.

Labour for cutting of M.S Angle iron post to required length one end splitted as fishtailed in a length of 150 mm complete as per building specification and direction of E/I.

Drilling 6 mm holes M.S angle iron for fixing of staples etc. as per building specification and direction of E/I .

Supplying fitting & Fixing straining bolt with nut size 25 cm x 10 mm dia tighten the barbed wire corner post complete as per building specification and direction of E/I .

Labour for fitting and fixing barbed wire fencing in four rows horizontal up to height of 1.25 M and two diagonals including fixing of post in cement concrete at 2.5 M . Centers including cost of staples (but excluding the cost of cement concrete angle iron post its cutting and making holes ,nut and bolts )all complete as per building specification and direction of E/I .

Providing 12mm thick cement plaster (1;6) with clean coarse sand of F M 1.5 including screening,curing with all leads and lifts of water.scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Colour washing two coats over a coat of white wash over new surface with approved quality of lime including cost of cleaning surface thoroughly and removing the scales of smoke & mosh marks with jhama, rubbing, scaffolding, washing of floors and taxes all complete as per building specification & direction of E/I.

Carriages of materials

(a) Brick -15 KM lead

(b) Sand -10 KM lead

(c) Stone chips 10 KM lead

(d) Cement- 25 KM lead

(e) Steel 25 KM lead

Aproach Road

Earth work in excavation in foundation trenches in ordinary soil (vide classification of soil item A) & disposal of excavated earth as obtained to a distance upto 50 m including all lifts, levelling, ramming the foundation trenches, removing roots of trees, shrubs all complete as per approve design, building specification & direction of E/Incharge.

Earthwork in Backfilling in road embankment with earth removed during excavated within initial lead and lifts as per specification and direction of Engineer in charge.

Rolling and compacting of road embankment in all kinds of soil including hard and gravelly soil, soil mixed with boulders by road roller in layers not exceeding 225mm. In loose thickness so as to achieve following maxmum dry density at O.M.C. uniformly, including mixing the required quantity of water including cost of supply and carriage of water with all leads and lifts finished the surface to proper grade, camber or super elevation including cost of hire charges of road roller, providing light, barrier, danger signal, chowkidar, all compolete, as per specification and direction of E/I.

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm. thick with all leads and lifts including cost of all materials, labours, royalty and taxes all complete job as per building specification and direction of the E/I. (mode of measurement compacted volume)

Providing dressed natural stone set pavement with stone bricks of hard igneous rock as per size 250mm x 125mm x 100mm over 12mm. Thick local sand of F.M. 1.8 as cusion including watering stone bricks placed true to the line level, grade and camber or super elevation, keeping at least 8mm between the set joints, staggered filled with cement mortar (1:4) sand of F.M. not less than 2.5 including curing for not less than 7 days cost of water and carriage with all leads and lifts, cost of all materials, labour screenign sand, taxes and royalty progviding light barrier, danger signal, regulation of traffic etc., all complete as per MoST specification and direction of E/I.

Providing P.C.C M-150 with nominal mix of (1:3:6) in foundation with quality of stone chips 20mm.to 6mm.size graded and clean sand of F.M.2.5 including screening, shuttering,mixing cement mortar in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification 7direction of E/I.

Carriages of materials

sand 10 KM lead

Stone/Stone Chips 10 KM lead

Cement 25 KM lead

Dismantaling of old ESR

Dismantling of ESR of various capacities and hight using crane (10 MT capacity) and handing over M.S./ C.I./ G.I. pipes, valves, bends, etc. to the Department However taking steel reinforcement by the dismantling agency including removing dismantled materials from site and disposing them at suitable place as directed, etc. complete.

2.27 Lakh liter capacity 18 M Staging.

House Connection for 3628 nos Consumer.

Earth work in excavation ( as per I.S. 3114/1965 for laying of different types and sizes of pipes so as to give 1 m av. cover over the socket of pipe with disposal of excavated earth within initial lead and lift as per specification and direction of E/l. (For soil item B)

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including' cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/l (Mode of measurement complacted volume).

(a) Provinding P.C.C M-150 with in norminal mix of (1:2:4) in foundation with approved quality of stone chips 20mm to 6 mm size graded and clean coarse sand of F.M 2.5 to 3 including , screening , shuttering, mixing cement concrete in mixture and placing in position vibrating striking curing taxes and royality all complete as per building specifiaction and direction of E/I

(b)Centering & shuteering for post Below GL & Above GL-

Earth work in back fillingthe trenches after laying of different types and sizes of pipes with earth removed during excavation within initial lead and lift as per specification and direction of E/I.(For soil item A & B)

Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing and supplying blue MDPE pipes confirming to ISO 4427:1996 manufactured from vergin resin PE 80 food grade compounded raw material having blue colour only assurance certificate from quality agencies like WRC / CIPET ( India) / DVGM / KIWA / SPGN etc. for usage in drinking water with quality system. The cost shall including cost all taxes, inspection charges transprotaion to work site and earth work involved , all complete job as per specification and direction of E/I. 20 mm dia pipe.

Providing and supplying G.I. pipes (Tata and equivalent make) for usage in drinking water with quality system, The cost shall include testing of all materials all taxes central , State , Municipal, Inspection charges transportation up to site transite insurance, loading, unloading, stacking etc. complete as specified and directed.

Lowering laying and jointing HDPE / MDPE pipe in proper position including all specials by Compression fitting / Electrofusion and But fusion jointing procedure including hydraulic testing as er relevent IS Code complete with all materials for jointing procedure like Electrofusion machine ,Electric mirrior/heater/But fusion welding machine with hydraulic testing and all labours as directed by engineer in charge as per IS-7634 part II

Supplying labour and tools for fixing G.I. pipes with Red lead and yarn of following nominal bore with screwed and socketted joints on wall, ceiling and floor including supplying and fitting of wall hooks or pipe clamps, wooden plugs, cutting pipes to size and threading ends if required etc. all complete as per specification and direction of E/l. (Pipe with socket to be supplied deparmentally free of cost).

Supplying and fixing G.M. ferrule of approved make in existing C.I./D.I. main including drilling and taping C.I./D.I. main all complete as per specification and direction of E/I. 3 mm, 6 mm 10 mm dia ferrule weight not less than 425 gram

Providing and fixing gun metal full way valve of approved quality all complete as per specification and direction of E/ (a) 20 mm dia and weight not less than 400 gram.

Providing and fixing 15 mm Dia male ended C.I Body Brass Spindle valve and seat bib cock of approved quality (Wt.not Less than 400 gms.) with extra socket all complete as per specification and Direction of E/I.

Supplying and fixing G.I. fittings of Approved make all complete as per specification and Direction of E/I

Elbow 20 mm

Elbow 15 mm

Reducing Socket 20 mm

Nipple 20 mm

Nipple 15 mm

Union Socket 20 mm

Socket 15mm

Socket 20 mm

Carriage of materials

Operation and maintenance for 1st year

Operation and maintenance for 2nd year

Operation and maintenance for 3rd year

Operation and maintenance for 4th year

Operation and maintenance for 5th year

Add 18% GST

Add 1% Labour Cess

M/S S.K. CONSTRUCTION (BID ID -647406)

AJAY KUMAR SINGH (BID ID -647405)