RequiredExperience with Government
RequiredAnnual Turnover
RequiredCertificate (Requested in ATC)
RequiredOEM Authorization Certificate
RequiredOEM Annual Turnover Bid to RA enabled Yes Note: 1. OEM Turn Over Criteria: The minimum average annual financial turnover of the OEM of the offered product during the last three years
Requiredending on 31st March of the previous financial year
Requiredshould be as indicated in the bid document. Documentary evidence in the form of certified Audited Balance Sheets of relevant periods or a certificate from the Chartered Accountant/Cost Accountant indicating the turnover details for the relevant period shall be uploaded with the bid. In case the date of constitution/incorporation of the OEM is less than 3 year old
Requiredthe average turnover in respect of the completed financial years after the date of constitution shall be taken into account for this criteria. LED Luminaire (For Road And Street Lights) ( 1000 pieces ) Technical Specifications 1/9 * As per GeM Category Specification Specification Specification Name Values Bid Requirement (Allowed Values) STANDARDS LED Luminaire conformity to IS:10322/Part 5/Section 3/2012 latest and IS: 16107 (Part 2/Sec 1):2012 latest Yes * Photo biological safety of LEDs used shall be as per IS:16108/2012 (exempt group) Yes * Types of LED Luminaire as per the IS: 16107(Part-2 Sec.-1)/2012 Type B * Types of LED Modules as per the IS:IS: 16103(Part-2)/2012 Type 3 * LED Rating (in Watts)/System Wattage/Rated Power 70W 70W Luminaire System Efficacy (Lumen/watt) >/= 100 Lm/Watt * Ingress Protection (IP Rating) as per IS:10322 (Part 1):1982 latest IP66 * Warranty for free replacement (in years) 5 4
Required5 ELECTRICAL EFFICIENCY Input operating Voltage range and frequency 90 to 300 Volts AC at 50 Hz+/-2 * Automatic Higher Cut off voltage above 300 volt Yes * Rated voltage 230 V AC 50 Hz * AC Power Factor at full load ≥ 0.95 * Driver Efficiency (in %age) Upto 100W: ≥85%
RequiredAbove 100W: >/=90% Yes * Total Harmonics Distortion ≤ 10 * "The total circuit power shall not be more than Yes * 2/9 110 percent of the value declared by the manufacturer (as per Cl. 8 of IS:16104:2012 lates)" OPTICAL LED chip Efficacy ≥130 Lm/Watt * Colour temperature 6000+/-500K * Working life for LED (Minimum 50
Required000 burning hours as per LM-80 and LM 21 reports) Yes * Colour Rendering Index(CRI) ≥70 * LED Beam Angle ≥120 * Optic lense materal (UV stabilised) Poly carbonate lense * THERMAL MANAGEMENT Heat sink should be die- cast aluminium along with sufficient heat sink fins to dissipate heat effectively Yes * Junctiojn/Soldering point temperature shall not exceed 85 deg.c as per LM 80 report Yes * Capacitor shall be rated for a temperature of 105 deg. celsius or better Yes * Operating temperature range -10 deg C to +55 deg C -20 deg. C to +50 deg. C
Required-10 deg C to +55 deg C Operating Humidity Range 10 % to 95% RH * PROTECTION Short circuit Protection Yes * Over load protecton Yes * Over Voltage protection Yes * Reverse polarity Yes * High voltage test (1.5 KV for one minute between supply terminals and body of the unit) Yes * Insulation resistance between earth and current carrying part >100 M Ohm * The luminaire shall be >/=4KV * 3/9 protected against surges and transients ( Internal) The luminaire shall be protected against surges and transients of >/=10KV (External) Yes * CONSTRUCTIONAL The Luminaires casing/housing (single piece housing) shall be pressure die casted aluminium alloy with higher thermal conductivity Yes * The luminaire body must be corrosion resistant powder coated Yes * All fastners must be of stainless steel Yes * Protection of the entire housing (both LED section and driver section) as per IS:10322 (Part 1):1982 latest IP66 * Extruded silicon loop gasket shall be provided in the lantern body to ensure a weather proof seal between the UV Glass cover and the metal housing to exclude the entry of the dust
Requiredwater
Requiredinsects etc.
RequiredYes * Luminaries light transparency should be of Toughened glass Yes * Toughned transparent glass cover thickness >/=4 mm * Toughned Glass shall not get discoloured shall not suffer degration due to heat and ageing within warranty period Yes * Number of electronic control gear (power supplies) 1 No. 1 No. Light Source SMD LED Chip as per LM 80/IS16106 * 4/9 Driver components shall be industrial grade or above Yes * PCB shall be FR4 grade minimum 0.8 to 1.0 mm thick or more Yes * The Luminaires works on single phase three wires system (Phase
RequiredNeutral and Earth) Yes * Suitable connector shall be provided for LED connection between driver output and LED Yes * Length of ISI marked three core wire (shall be provided along with supply of material) 100 cm 100 cm MARKING "Manufactures Name and and brand on the aluminium die cast body " Engraved/Embossed * Manufacturer’s name
Requiredmodel number
Requiredserial number Yes * Date of manufacture (month-year)
Requiredand lot number as identification mark inside each unit and the outside of each packaging box Yes * The operation characteristics voltage and power be marked inside of each LED luminaire unit Yes * Diameter of pole Luminiare suitable for: (upto 45W Pole OD: shall be 40mm)
Required(>45W<120W Pole OD: Shall be 50 mm)
Required(above 120W: OD shall be 60 mm for which luminiare is suitable Yes * REPORTS AND CERTIFICATIONS LED Make OSRAM/NICHIA/CREE SAMSUNG/SEOUL LUMILEDS/PHILIPS SYSKA/LUMENMAX * 5/9 EVERLIGHT/EDISON BRIDGELUX NATIONSTAR/REFOND System must have EMI/EMC compliance as applicable (Test reports shall be furnish to the buyer/consignee on demand) Yes * LM 79 (Photometry) (Ref.IS:16106:2012) report from Central Government Lab NABL/ILAC accrediated lab. Reports shall be furnish to the buyer consignee on demand (LM-79 report shall have total lumen output
Requiredpower
RequiredPF
RequiredCurrent in Amps
RequiredCRI & CCT etc.
Required) Yes * LM 80 & TM 21 (Ref. IS:16105:2012) Report and Photo biological report for LED report from Central Government Lab NABL/ILAC accrediated lab. Reports shall be furnish to the buyer consignee on demand (LM-80 report shall have the Pohoto Biological report of the LED Chip being used in the luminaire) Yes * Availability of test Report from Central Government Lab NABL/ILAC accrediated lab to Indian Standrad IS:10322/part 5/sec-3/2012 and IS 16107 (Part 2/Sec 1) : 2012 Yes * Seller shall furnish the Type test reports to the buyer/consignee on demand Yes * DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 Yes * 6/9 (Part 2/Sec.13) LED Luminaire for road and street lighting shall comply with Complusory Registration(CRS) of BIS for safety as per IS 10322 (Part 5/Section 3): 2012 as applicable on date Yes * * Specifications highlighted in bold are the Golden Parameters. * Bidders may note that In respect of non-golden Parameters
Requiredthe specifications 'Values' chosen by Buyer will generally be preferred over 'Bid requirement ( allowed Values) by the Buyer.
