GE (N) P/TOKEN- 17 OF 2022-2023 REPAIR/MAINTENANCE TO PUMP HOUSE PANEL BOARDS, INCLUDING REPLACEMENT OF STAR DELTA/DOL STARTERS, CONTACTORS, SINGLE PHASE PREVENTORS, REPLACEMENT OF PANEL BOARDS, METERS AND ALLIED ITEMS IN THE AREA OF AGE E/M(N) PUNE

Amount

Laying ony GI pipe medium grade in repair complete with and including provision of all of all fittings such as bend,elbow ,tee,socket,union etc laid in trenches of the following sizes complete all as specified and as directed. :- Note for Item No 1.01 to 1.04 All the pipe will be supplied under schedule 'B' free for fixing. Cost of transportation of pipe from stores to the site deemed to be included in quoted rates.

20 mm bore

25 mm bore

40 mm bore

50 mm bore

Excavation in trenches not exc. 1.5 Mtrs wide and not exc. 1.5 mtr deep and getting out in hard / dense soil complete all as specified and as directed.

Returning filling in including spreading levelling watering and well ramming in layers not exc 25 cm thick complete all as specified and as directed.

Removing of surplus excavated material to a distance not exceeding 50 mtr and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and as directed.

Supplying and fix in repairs Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and no pigments laid over and including a layer of 25 mm thick crushed sand cusion including filling the joints with crushed sand as in floor/path/ paving etc complete all as specified and as directed

Taking up and refixing carefully paver blocks of any size and shape required to be displaced for excavation purpose of the cable lines including the sand/red bajri/shingles beneath the same and consolidating the same after refiling of the earth complete all as specified and as directed by Engineer-in-charge. Note Necessary earth work for replacement / refixing of cable / pipe line will be measured and paidseperatly under relevant items

Material and labour for cutting existing road/hard standing for taking out cable /making new connection and making good with PCC (1:2:4) type C 1 (using 20 mm graded broken stone aggregate) surface finished even and fair complete all as specified and as directed by Engineer-in-charge.

Taking up/down of faulty LT under ground cable of any size and any capacity from trenches / pole / wall etc for detecting fault including repair and jointing at site including relaying at the same/other location with necessary glands, lugs etc complete all as specified and as directed. by Engineer-in-charge. Note: Excavation /earth work and cable jointing kit shall be measured and paid for separately under relevent item schedule.

S & F double wall corrugated high density polymer ethyl ( HDPE) pipe for laying of electric cable of 63 mm outer dia and 51 mm inner dia with conforming to IS- 14930 - 1 and 2, PE 63 of pressure rate 4 Kg/sq.cm laid in trenches ,wall, floor,pole including bends, sockets and other connected accessories complete all as directed and specified by Engineer-in-charge. Make:Dura Line/Tijaria/REX/Astral

Supply and Laying 40 mm outer dia double walled corrugated (DWC) HDPE duct Pipe conforming to IS- 14930 - 1 and 2, PE 63 of pressure rate 4 Kg/sq.cm with antirodent and non flame propogating properties of approved colour complete with fittings for cable protection complete all as specified and as directed by Engineer-in-charge. Make:Dura Line/Tijaria/REX/Astral

S & F flexible GI conduit in repairs alongwith taking up the required cables and refixing having bore of dia 25 mm and connecting the same with necessary and suitable glands complete all as specified and as directed by Engineer-In- charge

Supply and fix in repairs heat shrinkable LT straight through Joints sutaible for following cables :-

all as per item No 12 above 4 core 10-16 sq mm Make: 3M,Denson,Raychem

all as per item No 12 above but 4 core 25-35 sq mm Make: 3M,Denson,Raychem

Supply and lowering in repairs SUBMERSIBLE Flat Three Core PVC Insulated & PVC Sheathed Industrial Cable copper conductor mutistraned cable of size 3 core x 2.5 Sq mm for Submersible Pump Motor with necessary connections from Motor to starter complete with nessesary thimbles etc. complete all as specified and as directed. Make:Anchor ,Havells,Finolex

Supply and lowering in repairs SUBMERSIBLE Flat Three Core PVC Insulated & PVC Sheathed Industrial Cable copper conductor mutistraned cable of size 3 core x 4 Sq mm for Submersible Pump Motor with necessary connections from Motor to starter complete with nessesary thimbles etc. complete all as specified and as directed. Make:Anchor ,Havells,Finolex

Supply and lowering in repairs SUBMERSIBLE Flat Three Core PVC Insulated & PVC Sheathed Industrial Cable copper conductor mutistraned cable of size 3 core x 6 Sq mm for Submersible Pump Motor with necessary connections from Motor to starter complete with nessesary thimbles etc. complete all as specified and directed. Make:Anchor ,Havells,Finolex

Supply and replace for single core cable PVC insulated and unsheathed multistranded copper conductor of following sizes including removal old existing unserviceable one complete of following sizes all as specified and as directed.Make:Anchor ,Havells,Finolex

Supply and laying in replacement LT UG XLPE sheathed PVC insulated, screened PVC bedded, Galvanised Steel Strip armoured electric power cable / LT Panels heavy duty with stranded Aluminium Conductor 1100 Volt grade, laid in trenches/ surface of Wall/in GI Pipe along with Pole for connection to OH Lines/LT panels including removal of old cable, fixing of new brass cable glands etc and testing for following sizes, complete all as specified and as directed. Note : Earthworks etc. will be measured and paid under appropriate Items complete all as specified and directed. Make:anchor,Havells,Cable Corporation Of India

(a) 3.5 core x 16 Sqmm.

(b) 3.5 core x 25 Sqmm.

(c) 3.5 core x 35 Sqmm.

M&L for Servicing / testing of LT Distribution Panels / feeder pillar boxes ,03 Phase , 430 Volts , which includes following complete all as specified and directed. (I) Repair/ replacement of damaged hinges by welding of each compartment (ii) Cleaning of existing bus bars with CTC applying with red solution, providing bus bar insulation and re fixing with new nuts, bolts, washers etc. (iii) Replacement of damaged copper flexible cable and fixing new copper flexible cable for incoming and outgoing connections of each MCCB/switches terminals to bus bars (iv) Replacement of damaged/ worn out cable lugs any made / size for incoming & outgoing cables (v) Replacement of neoprene gasket for all doors of panel board.

Supply and replacement wall mounted Water Level Indicator, Overhead Tank Indicator, Led Indicator for Tank Water, Water Level Display with Wired Sensor Security System and water level indicator cum controller device for OH resevoir tank of 30 Mtr stagging showing 12 stage of water storage with necessary multi standard copper conductor cable 16 core 1.5 Sqmm armoured alongwith water level sensor including removal of old unsv one complete all as specified and as directed. Make:Autocon,Powertek,Spillguard Automation

Supply and fix in repairs 16 core 1.5 Sqmm armoured PVC Insulated and PVC Round Sheathed Multi Core Bright Annealed Bare Copper Conductor Heavy Duty Industrial Cables for Voltage Grade upto 1100 Volts as per IS: 694:1990 for water level sensor complete all as specified and directed. Make:Anchor ,Havells,Finolex Note: The Job involves suspending the same from RCC overhead tanks with maximum height of 30 mtrs

M & L for Relaying and joining of existing 16 core cable 1 to 1.5 Sqmm armoured using proper jointing with copper ferrules complete all as specified and directed. Note:- The Job included the M & L for joint to be used. Note: The Job involves suspending the same from RCC overhead tanks with maximum height of 30 mtrs

S & F in repairs sensor for water level indicators in RCC overhead tanks of 30 Mtr stagging and UG Sumps situated in water supply installation all over the area complete all as specified and as directed. Make:Autocon,Powertek,Spillguard Automation

Supply and lay in repairs 3- layer PP-R Polypropylene random copolymer) pipes SDR 7.4 & SDR 11 UV of following sizes fixed complete to walls, ceilings or in floors,laid in trenches etc. with all fitting such as tee, bends, union, elbow reducer, pasting adhesive materials etc with 25 mm outer dia of pipe complete all as specified and as directed. Make:Reliance,Kisan,SFMC

Demolition of old unservicible Brickwork or stone/boulder masonry but built in cement mortar or cement lime mortar complete all as specified and as directed.

Taking down cement plaster of any thickness and removing from site to a distnace exc 50 metre but not exc. 100 metre complete all as specified and as directed.

M&L for brick masonry with fly ash bricks exc 6 meter mean radius in cement mortar 1:6 complete all as specified and as directed.

M&L for rendering with 15mm thick in cement mortar 1:4 on fair surfaces of brick or concrete surafaces finshed even and smooth surfaces without using extra cement and all as specified and as directed by Engr-In-Charge.

Supply, Installations, testing ,commissioning and taking down old unserviceable LT outdoor panel board by CPRI approved manufacturer with active valid certificate having internal dimensions not less than 60 X 60X 30 cms with double door spring loaded self closing, with stopper only front side openable cubical type pedestal mounting type totally enclosed, fabricated with dust and weather proof and rating of IP 64 CRCA outer sheet of 3.00 mm thick and inner sheet not less than 2 mm as per IS, inner and outer compartment of Load Ball Bearing and 1.6 mm thick for non-load Ball Bearing suitable for 3 phase 4 wire system 415 volts bottom base channel of MS section not less than 50 mm x 50 mm x 5mm thickwith proper earthing arrangement. Finish of the panel shall be powder coated, dust & vermin proof of IP 65 compartment doors, all components mounted on iron sheet 2mm thick and having proper locking arrangement in both front including necessary foundation, brick/PCC masonary pillar in CM 1:6, plastering 1:4, 10mm thick with clearance atleast 1.2 m above ground level, including marking incoming , outgoing cables with glands etc name of feeders and comprising with supply and fixing of the following items and connecting and testing complete all as specified and as directed. (a) MCB "C" curve , 4 pole , 415 Volts of current rating 16 Amps, rupturing capacity 10 KA- 01 No Make:Hager Cat No.NCN416N,L& T BB40160D ,Schneider cat no.A9N4P16D. (b) Three phase prewired Direct on line pumpset starters with actuators in steel sheet enclosure 9-15/8-12.5 Amp relay for 5/7.5 HP pumpsets L& T cat no.MU G6,siemens3TW72911A.75,ABB (d) LED indicators RYB Make L & T ,Schneider,Siemens (e) LED indicators for motor on ,off and trip status.Make L & T ,Schneider,Siemens

Supply, Installations, testing ,commissioning and taking down old unserviceable LT indoor panel board by CPRI approved manufacturer with active valid certificate having internal dimensions not less than 100 X 78X 30 cms with double door spring loaded self closing, with stopper only front side openable cubical type pedestal mounting type totally enclosed, fabricated with dust and weather proof and rating of IP 54 CRCA sheet of 2 mm thick as per IS, inner and outer compartment of Load Ball Bearing and 1.6 mm thick for non-load Ball Bearing suitable for 3 phase 4 wire system 415 volts with insulated aluminium bus bar of rating 100 Amps for phases neutral, duly supported on SMC insulators, bottom base channel of MS section not less than 100 mm x 50 mm x 5mm thick.common separate earth bus of aluminium flat of size 25x3mm shall be provided along the entire length of the panel board and two sides of this earth bus bar will be separely earthed. Finish of the panel shall be powder coated, dust & vermin proof of IP 65 compartment doors, and having proper locking arrangement in both front and rear sides and necessory foundation, brick/PCC masonary pillar in CM 1:6, plastering 1:4, 10mm thick with clearance atleast 0.40m above ground level, including marking incoming , outgoing name of feeders and comprising with supply and fixing of the following items and connecting and testing complete. ( For 64 Pump House N0. 3) (a) Aluminium busbar suitable for three phase four wire system of current rating 100 Amps covered with coloured PVC sleeves as per colour code mounted on DMC insulators -01set (b) MCB "C" curve , 4pole , 415 Volts of current rating 40 Amps, rupturing capacity 10 KA- 01 No Make:Hager Cat No. NCN440N ,L & T BB40400D,Schneider cat no.A9N4P40D. (c) MCB "C" curve, 3 pole of current rating 20 Amps rupturing capacity 10 KA -02 Nos Make:Hager,L & T BB30200D ,Schneider cat no.A9N3P20D.

Material and labour for attending the emergent complaint and repairs to centrifugal monoblock pumpset of 3 HP to 25 HP including carrying out minor repairs etc as required to make the system in order/ functional and necessary gland,rubber sheet ,nut , bolts , washers and phase sequence change , electric supply connections from switchgear/starter/Panel etc.complete all as specified and directed by Engineer-in-charge

Material and labour for attending the emergent complaint and repairs to centrifugal inline booster/lifting pumps of 0.25 HP to 1 HP including carrying out minor repairs etc as required to make the system in order/ functional and necessary gland,rubber sheet ,nut , bolts , washers and auto/manual reset , electric supply connections from switchgear/starter/Panel etc. complete all as specified and directed by Engineer-in-charge

Material and labour for attending the emergent complaint and repairs to centrifugal borewell/openwell pumpsets of 0.5 HP to 5 HP including carrying out minor repairs etc as required to make the system in order/ functional and necessary gland,rubber sheet ,nut , bolts , washers and phase sequence change , electric supply connections from switchgear/starter/Panel etc.complete all as specified and directed by Engineer-in-charge

M & L for rewiring of the control wiring of single phase DOL starters by connecting existing MCB's,thermal overload relays, contactors etc. using FRLS single core bright annealed multistranded 1.5 sq mm copper wire with necessary accessories such as PVC tags, thimbles,cable worms,PVC cable trays etc complete all as specified and as directed. Make Of cable: Make:Anchor ,Havells,Finolex

M & L for rewiring of the control wiring of three phase DOL starters by connecting existing MCB's,thermal overload relays, contactors etc. using FRLS single core bright annealed multistranded 1.5 sq mm copper wire with necessary accessories such as PVC tags, thimbles,cable worms,PVC cable trays etccomplete all as specified and directed. Make Of cable: Make:Anchor ,Havells,Finolex

M & L for rewiring of the control wiring of three phase star-delta starters by connecting existing MCB's,thermal overload relays, contactors, timers etc. using FRLS single core bright annealed multistranded 1.5 sq mm copper wire with necessary accessories such as PVC tags, thimbles,cable worms,PVC cable trays etc complete all as specified and directed.Make Of cable: Make:Anchor ,Havells,Finolex

Supply and replacement single phase preventer having capability to sense single phasing, reverse phasing, unbalanced supply with Auto reset, 1 NO output contact Suitable for any HP/kW rating monoblock pumps Pre-wired terminals for easy connections complete all as specified and as directed. Make Minilec VSP3, GIC L & T,Selec 800 PSR

S & F in repairs LCD Multifunction Meters Input voltage measurement range 3 x 240 VAC (-30% to 20%), Aux supply 90-300 VAC/DC,Flush mounting 96 x 96 mm ,CT/PT site Programmable having accuracy class 1.0 with RS485 port Parameters: V, A, F, PF, kW, kWh with new CT's-01 No.s complete all as specified and directed. Make L&T WL440511OOOO, IMP, Automatic Electric

Supply and replacement only LED indicator lamps R,Y,B,G,W with holder 16 mm screw type including removal of existing unserviceable one complete all as specified and as directed by Engg-in- charge.Make:Make L&T, IMP, Automatic Electric

S & F in repairs flush actuator buttons with inbuilt contacts arrangement Contact rating 6A @ 240AC of any desired colour at site complete all as specified and directed.Make: L & T, GE, siemens

S & F in repairs MS/GI hinges by welding/rivetting with existing panel having dia 8 mm to 12 mm and painting the same with existing colour and matching with the same complete all as specified and as directed.

M & L for fixing fabricated with dust and weather proof CRCA sheet of 2 mm thick as per IS powder coated MS sheet LT outdoor panel cover with necessary neoprene gasket,locking and hanging arrangement with existing panel board complete all as specified and as directed.

S & F in repairs panel locks of existing type with necessary keys etc complete all as specified and as directed.

Labour for shifting indoor/outdoor LT panel of size not more than 2.5mx1.5mx0.5m from one place to another by demolition of grouting PCC at first place and installing the same with brick/PCC masonary pillar in CM 1:6, plastering 1:4, 10mm thick with clearance atleast 0.4 m above the ground level connecting and disconnecting the associated cable with proper glands , nut ,bolts,washers and thimbles etc & reconnection of cable completed all as specified & as directed by Engineer-in-charge

S & F in repairs following panel accessories with capacity and size Confirming to IS / IEC 60947-4-1 & IEC 60947-4-1 complete all as specified and directed:-

3 Pole contactor 415 Volt 50 Hz coil AC-3 rating 9 Amps including auxillary No/NC add on blocks Make L &T Model MNX 9 cat No.CS94106/7 or equivalent in havells,Indoasian,C&S or as per existing at site all as specified and as directed by Engineer-in-charge.

3 Pole contactor 415 Volt 50 Hz coil AC-3 rating 12 Amps including auxillary No/NC add on blocks Make L &T Model MNX 12 cat No.CS94108/9 or equivalent in havells,Indoasian,C&S or as per existing at site all as specified and as directed by Engineer-in-charge.

3 Pole contactor 415 Volt 50 Hz coil AC-3 rating 18 Amps including auxillary No/NC add on blocks Make L &T Model MNX 18 cat No.CS941010/11 or equivalent in havells,Indoasian,C&S or as per existing at site all as specified and directed by Engineer-in-charge.

3 Pole contactor 415 Volt 50 Hz coil AC-3 rating 25 Amps including auxillary No/NC add on blocks Make L &T Model MNX 25 cat No.CS94110 or equivalent in havells,Indoasian,C&S or as per existing at site all as specified and directed by Engineer-in-charge.

3 Pole contactor 415 Volt 50 Hz coil AC-3 rating 40 Amps including auxillary No/NC add on blocks Make L &T Model MNX 40 cat No.CS94190 or equivalent in havells,Indoasian,C&S or as per existing at site all as specified and as directed by Engineer-in-charge.

3 Pole contactor 415 Volt 50 Hz coil AC-3 rating 32 Amps including auxillary No/NC add on blocks Make L &T Model ML 2 cat No.SS90701 or equivalent in havells,Indoasian,C&S or as per existing at site all as specified and as directed by Engineer-in-charge.

3 Pole contactor 415 Volt 50 Hz coil AC-3 rating 15 Amps including auxillary No/NC add on blocks Make L &T Model MK 1 cat No.SS95200 or equivalent in havells,Indoasian,C&S or as per existing at site complete all as specified and as directed by Engineer-in-charge.

2 pole contactor 240 Volt 50 Hz coil AC-3 rating 16 Amps including auxillary No/NC add on blocks Make L &T Model MU2P cat No.CS90117 or equivalent in havells,Indoasian,C&S or as per existing at site complete all as specified and as directed by Engineer-in-charge.

1 pole contactor 240 Volt 50 Hz coil AC-3 rating 25 Amps including auxillary No/NC add on blocks Make L &T Model MR11W cat No.CS94176 or equivalent in havells,Indoasian,C&S or as per existing at sitecomplete all as specified and as directed by Engineer-in-charge.

Spare contactor coil 415 V 50 Hz for model series MNX/ML/MR/MU 9-40 amps upto 25 HP motor Make:L &T cat no.CS94105 or equivalent in havells,Indoasian,C&S or as per existing at site complete all as specified and as directed by Engineer-in-charge

Spare contactor kit 3 pole for contactor model ML2 or equivalent as required at site complete all as specified and as directed

Spare contactor kit 2 pole for contactor model MU2P or equivalent as required at site complete all as specified and as directed

Spare contactor kit 1 pole for contactor model MR11W or equivalent as required at site complete all as specified and as directed

MCB SP 5-32Amps 10 KA "B" curve complete all as specified and as directed Make L& T,Schneider,Legrand

MCB SPN 5-32Amps 10 KA "K" curve complete all as specified and as directed Make L& T,Schneider,Legrand

MCB 3 pole 5-32Amps 10 KA "K" curve complete all as specified and as directed Make L& T,Schneider,Legrand

MCB 4 pole 5-32Amps 10 KA "K" curve complete all as specified and as directed Make L& T,Schneider,Legrand

S & F in repairs MCCB 40 amps 3 pole with thermal magnetic release breaking capacity 10 KA with Tcs=T cu=100% Make L&T,Havells,Indoasian,MEC (as per site requirement) complete all as specified and as directed by Engineer-in-charge.

S & F in repairs MCCB 40 amps 4 pole with thermal magnetic release breaking capacity 18 KA with Tcs=T cu=100% Make L&T,Havells,Indoasian,MEC (as per site requirement) complete all as specified and directed by Engineer-in-charge.

S & F in repairs MCCB 63 amps 3 pole with thermal magnetic release breaking capacity 10 KA with Tcs=T cu=100% Make L&T,Havells,Indoasian,MEC (as per site requirement) complete all as specified and as directed by Engineer-in-charge.

S & F in repairs MCCB 63 amps 4 pole with thermal magnetic release breaking capacity 18 KA with Tcs=T cu=100% Make L&T,Havells,Indoasian,MEC (as per site requirement) complete all as specified and directed by Engineer-in-charge.

S & F in repairs MCCB 100 amps 3 pole with thermal magnetic release breaking capacity 10 KA with Tcs=T cu=100% Make L&T,Havells,Indoasian,MEC (as per site requirement) complete all as specified and as directed by Engineer-in-charge.

S & F in repairs MCCB 100 amps 4 pole with thermal magnetic release breaking capacity 18 KA with Tcs=T cu=100% Make L&T,Havells,Indoasian,MEC (as per site requirement) complete all as specified and directed by Engineer-in-charge.

S & F in repairs MCCB 125 amps 3 pole with thermal magnetic release breaking capacity 10 KA with Tcs=T cu=100% Make L&T,Havells,Indoasian,MEC (as per site requirement) complete all as specified and as directed by Engineer-in-charge.

S & F in repairs MCCB 125 amps 4 pole with thermal magnetic release breaking capacity 18 KA with Tcs=T cu=100% Make L&T,Havells,Indoasian,MEC (as per site requirement) complete all as specified and as directed by Engineer-in-charge.

S & F in repairs MCCB 200 amps 3 pole with thermal magnetic release breaking capacity 25 KA with Tcs=T cu=100% Make L&T,Havells,Indoasian,MEC (as per site requirement) complete all as specified and as directed by Engineer-in-charge.

S & F in repairs MCCB 125 amps 4 pole with thermal magnetic release breaking capacity 25 KA with Tcs=T cu=100% Make L&T,Havells,Indoasian,MEC (as per site requirement) complete all as specified and as directed by Engineer-in-charge.

S & F in repairs Star Delta pumpset starters Electronic timer 3-30 sec for 240 / 360 / 415V, 50Hz system for pumpsets upto 25 HP Make L &T (ST 100),Selec, C &S,TC complete all as specified and as directed.

S & F in repairs single phase pumpset starters Electronic timer 3-120 sec for 240 / 360 / 415V, 50Hz system for pumpsets upto 25 HP with Tcs=T cu=100%Make L &T ,Selec, C &S,TC,GIC complete all as specified and as directed.

S & F in repairs 3 pole thermal overload relay for MNX type contactors 415 V current range 9-15Amps for pumpsets upto 25 HP Make L & T,C &S,TC (as per site requirement) complete all as specified and as directed by Engineer-in-charge.

S & F in repairs 3 pole thermal overload relay for MNX type contactors 415 V current range 14-23Amps for pumpsets upto 25 HP Make L & T,C &S,TC (as per site requirement) complete all as specified and directed by Engineer-in-charge.

S & F in repairs 3 pole thermal overload relay for MNX type contactors 415 V current range 20-33 Amps for pumpsets upto 25 HP Make L & T,C &S,TC (as per site requirement) complete all as specified and as directed by Engineer-in-charge.

S & F in repairs 3 pole thermal overload relay for MNX type contactors 415 V current range 24-40 Amps for pumpsets upto 25 HP complete all as specified and as directed. Make L & T,C &S,TC

S & F in repairs 3 pole thermal overload relay for ML-2 type contactors 415 V current range 9-14,13-21,20-32,28-42 Amps for pumpsets upto 25 HP Make L & T,C &S,TC (as per site requirement) all as specified and as directed by Engineer-in-charge.

S & F in repairs 2 pole thermal overload relay for MU type contactors 415 V current range 11-18 Amps for pumpsets upto 25 HP Make L & T,C &S,TC (as per site requirement) complete all as specified and as directed by Engineer-in-charge.

S & F in repairs 4 pole Manual Changeover Open Execution with handle 415 Volts,63 amps Make L & T,C & S(as per site requirement) (as per site requirement)complete all as specified and as directed by Engineer-in-charge.

S & F in repairs 4 pole Manual Changeover Open Execution with handle 415 Volts,100 amps Make L & T,C & S(as per site requirement) (as per site requirement) complete all as specified and as directed by Engineer-in-charge.

S & F in repairs Operating Handle for change over as mentioned in above two items complete all as specified and as directed.

S & F in repairs rotary Handle for MCCB 40-200 amps 3/4 pole (as per site requirement) complete all as specified and as directed by Engineer-in-charge.

S & F in repairs starters single phase prewired for centrifugal pumpset with necessary parameter indicators and actuators of following capacity in steel sheet enclosure and connecting to the existing cable complete all as specified and as directed by Engr-in-charge Make: L &T,Siemens, ABB

(a) 1HP ,relay range 6-10 Amps ,230 Volts 50 Hz Make L&t cat no.CS90319KOVO,havells model urja

(b) 2HP ,relay range 11-18 Amps ,230 Volts 50 Hz Make L&t Cat no.CS90319KOCO,havells model urja

(c) 3HP ,relay range 13-22 Amps ,230 Volts 50 Hz Make L&t Cat no.CS90319KODO,havells model urja

S & F in repairs single phase prewired submersible pumpset starters with necessary parameter indicators and actuators of following capacity in steel sheet enclosure and connecting to the existing cable complete all as specified and as directed by Engr-in-charge

(a) 1HP ,realay range 6-10/9-14 Amps ,230 Volts 50 Hz Make L&t cat no.CS91041BCVG/CS91041BCAG,havells model urja

(b) 1.5HP ,realay range 9-14/11-18 Amps ,230 Volts 50 Hz Make L&t Cat no.CS91042BDAF/CS91042BDCF,havells model urja

(c) 2HP ,realay range 11-18/13-22 Amps ,230 Volts 50 Hz Make L&t Cat no.CS91043BECF/CS91043BEDG,havells model urja

(d) 3HP ,realay range 13-22 Amps ,230 Volts 50 Hz Make L&t cat no.CS91044BEDH,havells model urja

S & F in repairs three phase prewired Direct on line pumpset starters with necessary parameter indicators and actuators in steel sheet enclosure 9-15/8-12.5 Amp relay for 5/7.5 HP pumpsets all as diected and specified by Engr-in-charge make: L& T cat no.MN 16 SS94351,siemens3TW72911A.75,ABB

S & F in repairs three phase prewired fully automatic star delta pumpset starters with necessary parameter indicators and actuatorshaving wideband coil volatage capacity in steel sheet enclosure 9-15/10-16 Amp relay for 15/17.5 HP pumpsets complete all as specified and as directed. by Engr-in-charge make: L& T cat no.SS94362 ,siemens 3TE72910A.77,ABB

S & F in repairs PVC Insulated Single Core 16 sqmm Unsheathed Industrial Flexible Cable conforming to IS 694:1990 with Flexible Bright Annealed Copper Conductor for Voltage Grade 1100 Volts complete all as specified and directed.

Supply and fix in repairs resin casted copper wounded Current transformer having following ratio and VA burden as per site requirement complying with IEC : 62053-21 / IS: 13779 and accuracy of class I including necessary connection with energy meter complete all as specified and as directed by Engr-in-charge

current transformer coil with ratio100/5

current transformert coil with ratio 60/5

current transformer coil with ratio 40/5

Supply and replacement Motor protection relay with in-built earth fault protection MPR300 O/L 4-11 including removal of existing unserviceable one complete all as specified and as directed by Engg-in- charge.

M&L for running welding of CI/DI/MS thickness n'exc 6mm in repairs complete all as specified and as directed by Engr-in-charge

S & F in repairs Aluminium alloy, anodised, 150 mm sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extrudedsections or cast-aluminium alloy and fixed with gi nut bolts, washers on the doors of outdoor LT Panels complete all as specified and as directed. by Engr-in-charge

Supply and replacement dry run Motor protection relay with inbuilt microprocesssor controlled Auto/Manual/Bypass Mode available ,suitable for all starters – upto 40A able to work on 240 V and 415 Volts complete all as specified and as directed by Engg-in- charge. Make L & T cat no. I-AD, or equivalent in siemens,schneider

Taking down / up for repair centrifugal pump Set from foundation, separating pump and motor, opening motor separating stator , rotor and carrying out the repairs and replacement of unserviceable spares reassembling and connecting up with the electric motor all as specified for the following capacity Replacement of spare parts all as specified and as given here in after during the process of repair of of pump set of following capacity & reconnecting the same after repairs as complete all as specified and as directed Make of pumpsets kirloskar,Crompton ,CRI Note:- The quoted rate involes M & L for temporary joining of pipe lines or fixing of blank plates etc as per site requirment

0.5 HP 1 phase , 230 Volts 50 HZ

1 HP 1 phase , 230 Volts 50 HZ

3.0-5.0 HP 3 phase , 415 Volts 50 HZ

7.5 HP 3 phase , 415 Volts 50 HZ

10.0 -15.0 HP 3 phase , 415 Volts 50 HZ

18.5/ 20.0-25 .0 HP 3 phase , 415 Volts 50 HZ

M & L for rewinding with the same gauge of winding wire after Cleaning of rotating and static parts of motors , removing burned out winding , cleaning the slots, insulation of slots,reassembling the pump sets for the following capacites :- Make of pumpsets kirloskar,Crompton ,CRI 0.5-1 HP 1 phase , 230 Volts 50 HZ

0.5-1 HP 1 phase , 230 Volts 50 HZ

3.0 HP 3 phase , 415 Volts 50 HZ

5.0 HP 3 phase , 415 Volts 50 HZ

7.5 HP 3 phase , 415 Volts 50 HZ

10.0 HP 3 phase , 415 Volts 50 HZ

12.5 HP 3 phase , 415 Volts 50 HZ

15.0 HP 3 phase , 415 Volts 50 HZ

18.5/ 20.0 HP 3 phase , 415 Volts 50 HZ

25.0 HP 3 phase , 415 Volts 50 HZ

Supply and fix in repairs the spares for centrifugal pump with their respective capacities as mentioned for following complete all as specified and as directed.:Make of pumpsets kirloskar,Crompton ,CRI

Impeller made of brass for 0.5 HP pump

Impeller made of brass for 1 HP pump

Impeller made of CI for 3HP pump

Impeller made of CI for 5-7.5 HP pump

Impeller made of CI for 10 HP pump

Impeller made of CI for 12.5 HP pump

Impeller made of CI for 15 -25HP pump

PVC cooling fan for 0.5-1 HP pump

PVC cooling fan for 3-7.5 HP pump

PVC cooling fan for 10-25 HP pump

Pump shaft made of stainless steel for 0.5HP pump

Pump shaft made of stainless steel for 1 HP pump

Pump shaft made of stainless steel for 3-5 HP pump

Pump shaft made of stainless steel for 7.5-12.5HP pump

Pump shaft made of stainless steel for 12.5-15 HP pump

Pump shaft made of stainless steel for 18.5/20-25HP pump

Sleeve made of stainless steel for 3 HP pump

Sleeve made of stainless steel for 5-10 HP pump

Sleeve made of stainless steel for 12.5-15 HP pump

Sleeve made of stainless steel for 18.5/20-25 HP pump

Ball Ball Bearing made of stainless steel for 0.5-10 HP pump Make SKF,Tata,NBC(NEI)

Ball Ball Bearing made of stainless steel for 3 HP pump Make SKF,Tata,NBC(NEI)

Ball Bearing made of stainless steel for 5 HP pump Make SKF,Tata,NBC(NEI)

Ball Bearing made of stainless steel for 7.5 HP pump Make SKF,Tata,NBC(NEI)

Ball Bearing made of stainless steel for 10 HP pump Make SKF,Tata,NBC(NEI)

Ball Bearing made of stainless steel for 12.5 HP pump Make SKF,Tata,NBC(NEI)

Ball Bearing made of stainless steel for 15 HP pump Make SKF,Tata,NBC(NEI)

Ball Bearing made of stainless steel for 20 HP pump Make SKF,Tata,NBC(NEI)

Ball Bearing made of stainless steel for 25 HP pump Make SKF,Tata,NBC(NEI)

Shaft Lock

Water seal for 0.5 to 1HP pumpset

Gland Cap made of CI for 3-7.5 HP pump

Gland Cap made of CI for 10-15 HP pump

Gland Cap made of CI for 18.5/20-25 HP pump

Gland Cap bolts made of stainless steel

Coupling assembly assembly with key for 20-25 HP pump

Lathe machine work for Pump

Bakelite electrical 6/3 pole terminal for 3-5HP motor

Bakelite electrical 6/3 pole terminal for 7.5-10HP motor

Bakelite electrical 6/3 pole terminal for 20-25HP motor

Brass air release key and socket complete set

M & L for Lifting of vertical/ horizontal submersible pump set of upto capacity 1HP to 15 Phase 220/415 V 50 Hz from borewell/shallow well of depth from 40M to 70M by disconnecting the electrical connections, column pipes of various sizes, submersible cable, removing carefully to store for safe custody or transportaion to workshop for repair and back and reinstallation after repair of pump set and testing all as specified complete all as directed by EIC.

M & L for Opening the submersible pumpset , carrying out the repairs and replacement of unserviceable spares reassembling and connecting up with the electric motor all as specified Replacement of spare parts all as specified and as given here in after during the process of repair of pump upto 5.0 HP Submersible Pump set vide Sl item No 86 above

M & L for Cleaning of rotating and static parts of motors , removing burned out winding , cleaning the slots, insulation of slots, rewinding with the same gauge of PVC coated copper winding wire,reassembling the pump sets for the following capacity submersible pump complete all as specified and directed. Make of pumpsets kirloskar,Crompton ,CRI,Beacon

M & L for Cleaning of rotating and static parts of motors , removing burned out winding , cleaning the slots, insulation of slots, rewinding with the same gauge of copper winding wire including replacement of unserviceable mechanical seal,angular Ball Bearing and cable etc,reassembling the pump sets for the following capacity submersible pump.

Supply and fix in repairs the spares for vertical centrifugal submersible pump with their respective capacities as mentioned of following:

Top bowl housing assembly

"O" ring valve metal seat

Brass sleeve/distance piece

Key set

Stage Bowl

Thrust Ball Bearing assembly

Lathe work for pump

Strainer (with screwing etc.)

Brass bush (4 No's set)

Coupling assembly

Impeller made of FRP Vinyl impellar for V4 engines

Pump shaft

Diffuser

Cable guard made of stainless steel

Cheese haed cap screw

Casing strip with threaded bolt end

Transformer oil having dielectric strength 50Kv/2.5mm Make:Indian oil

Sand guard

Rotor shaft pump

CIR clip

Lower end of the shield of motor/pump

M & L for Opening the horizontal/openwell submersible pump set of following capacity , carrying out the repairs and replacement of unserviceable spares reassembling and connecting up with the electric motor all as specified for the following capacity of pumpset Replacement of spare parts all as specified and as given here in after during the process of repair of of pump of horizontal submersible pump set with capacities from 0.5 HP to 5 HP single phase and three phase complete all as specified and as directed.

Motor rewinding 1-1.5 HP 230 V 50 Hz

Motor rewinding 2 HP 230 V 50 Hz

Motor rewinding 3 HP 415 V 50 Hz

Motor rewinding 5 HP 415 V 50 Hz

Motor rewinding 7.5 HP 415 V 50 Hz

Motor rewinding 10 HP 415 V 50 Hz

Motor rewinding 15 HP 415 V 50 Hz

Lathe machine work for pump/motor any capacity

Brass bush 1 HP 230 V 50 Hz

Brass bush 1.5-3 HP 230 V 50 Hz

Brass bush 5-7.5 HP 415 V 50 Hz

Brass bush 10-15 HP 415 V 50 Hz

Carbon Thrust Ball Bearing and plate for 1-2 HP 230 V 50 Hz

Carbon Thrust Ball Bearing and plate for 3 HP 415 V 50 Hz

Carbon Thrust Ball Bearing and plate for 5 HP 415 V 50 Hz

Carbon Thrust Ball Bearing and plate for 7.5 HP 415 V 50 Hz

Carbon Thrust Ball Bearing and plate for 10-15 HP 415 V 50 Hz

Impeller made of cast iron 1 HP 230 V 50 Hz

Impeller made of noyl PVC iron 1.5 HP 230 V 50 Hz

Impeller made of cast iron 2-3 HP 230 V 50 Hz

Impeller made of cast iron 5 HP 415 V 50 Hz

Impeller made of cast iron 7.5 HP 415 V 50 Hz

Impeller made of cast iron 10-15 HP 415 V 50 Hz

Supply ,fabricate and fix in replacement column pipe with heavy grade GI tubing of size 25 mm dia in 3M length and heavy duty fittings for submersible pump set complete all as specified and directed. MAKE of pipe :- Tata,Zenith,Jindal NOTE :- Quoted rate shall deemed to be inclusive of the material and labour cost for the following :- (i) Socket fully screwed and welded at one end.

Supply ,fabricate and fix in replacement column pipe with heavy grade GI tubing of size 40 mm dia in 3M length and heavy duty fittings for submersible pump set complete all as specified and directed. MAKE of pipe :- Tata,Zenith,Jindal NOTE :- Quoted rate shall deemed to be inclusive of the material and labour cost for the following :- (i) Socket fully screwed and welded at one end.

Supply ,fabricate and fix in replacement column pipe with heavy grade GI tubing of size 50 mm dia in 3M length and heavy duty fittings for submersible pump set complete all as specified and directed. MAKE of pipe :- Tata,Zenith,Jindal NOTE :- Quoted rate shall deemed to be inclusive of the material and labour cost for the following :- (i) Socket fully screwed and welded at one end.

Supply and fix in repairs nylon rope as per the site requirement for borewells with HDPE pipes

Supply and fix/ lowering in repairs High density poly ethylene pipes (HDPE) of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors, trenches,borewell etc. including necessary fittings such as tee,bends,elbow etc having bore sizes as following of Make :SFMC ,Finolex,Supreme:-

(i) 25 mm bore

(i) 40 mm bore

(ii) 50 mm bore

M&L in repair CI borewell cap of size 300mm dia 6mm thickness and similar to casing pipe including necessary nuts, bolts etc complete all as specified and as directed.

M&L for Angle Iron,flat iron etc as in broken or unserviceable cross arms, brazings, supports,, clamps and back plate fabricated from structural steel sections including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of paint complete all as specified and as directed.

Supply and fix in repairs heavy duty iron chain able to withstand a weight of 50-100 kgs at a height of not less than 6 mtrs complete all as specified and as directed.

M&L for PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) for plinth ,founation,platform etc including necessary formwork and demolition of unserviceable structure complete all as specified and as directed.

M&L for PCC 1:2:4 type B -1 (using 20 mm graded stone aggregate) for plinth ,founation,platform etc coverincluding necessary formwork and demolition of unserviceable structure complete all as specified and as directed.

Supply and fix on replacement on-line pressure boosting pump, outdoor, weather proof electrically operated 240 volts, 50 Hz fixed to 15/20 mm dia of capacity Head 10 mtrs Flow rate-35 LPM power input 0.1 KW with three opearting position OFF/AUTO/MANNUL and componants of ceramic radial Ball Bearing, copper stator winding, EPDM rubber gasket, Aluminium oxide Shaft, carbon trust Ball Bearing, composit PP30% GF impeller including the integrated flow switch starts or stops the pump when a tapping point is turned on or off including, electrical connections, relaying of pipe lines, GI fittings, and removal of old unsv one complete all as specified and as directed. Make :- Wilo Model PB88, Kirloskar Model K Boost Grundfos Model UPA 15-90

Supply and fix on replacement on-line pressure boosting pump, outdoor, weather proof electrically operated 240 volts, 50 Hz fixed to 15/20 mm dia of capacity Head 16 mtrs Flow rate-50 LPM power input 0.2 KW with three opearting position OFF/AUTO/MANNUL and componants of ceramic radial Ball Bearing, copper stator winding, EPDM rubber gasket, Aluminium oxide Shaft, carbon trust Ball Bearing, composit PP30% GF impeller including the integrated flow switch starts or stops the pump when a tapping point is turned on or off including, electrical connections relaying of pipe lines, GI fittings, GI fittings and removal of old unsv one complete all as specified and as directed. Wilo Model PB200, Kirloskar Model K Boost Grundfos Model UPA 120

Supply and fix on replacement water lifting pump 0.5 Hp single phase suction and discharge, copper wounded stator ( 25 mm x 25 mm ) total head upto 6- 42 mtr, capcity upto 2120 LPH monoblock pump type suitable for 230 volts with all necessary fittings including copper cable upto 5mtr.Including removol of old unsv one complete all as specified and as directed.Make Make Kirolsakar model Jalraj 2 Ultra, Texmo Model SHR2, Wilo Model Mini Prince

Supply and fix on replacement water lifting pump 1 Hp single phase suction and discharge,copper wounded stator ( 25 mm x 25 mm ) total head upto 6-42 mtr, capcity upto 3300 LPH monoblock pump type suitable for 230 volts with all necessary fittings including copper cable upto 5mtr.Including removol of old unsv one complete all as specified and as directed Make Kirolsakar model Jalraj 2 Ultra, Texmo Model SHR4, Wilo Model Mini Crown10

Supply and fix on replacement water lifting and booster pump 1.5 Hp single phase suction with necessary factory fabricated auxillary tank and discharge,( 25 mm x 25 mm ) total head upto 10-42 mtr, capcity upto 75 - 6 LPM monoblock, multiple noryl/brass impellar pump type suitable for 230 volts with all necessary fittings including copper cable upto 5mtr.Including removol of old unsv one complete all as specified and as directed Make kirloskar CPBS 84424H/V,KSB KSB KHM 406,Texmo ADBS 44 HS / 60L

Supply install in repairs and testing of submersible non clog self priming dewatering pumpsets able to handle fluids and semi solids with induction squirrel cage motor operational on 3 phase 440 Volts, 50 Hz 2.2KW shaft power including necessary flanges/reducer for pipe with following specifications:- No. of stages 1 Discharge 202 LPM (Minimum required) Head - 20 meter (Minimum required) Speed -2900 RPM (during stable operation) Pipe size -50 mm Input at shaft 2.2 BKW Suitable Motor -2.2 KW Material of construction Impeller : Cast Iron Delivery Casing : Cast Iron Motor Body : Cast Iron Pump Shaft : Carbon Steel AC, 3 phase, 415 Volts, 50 Hz, conforming to IS 14220 : 1994 Make : Kirloskar Catno.2200CW / Jyoti/ Crompton Cat no.STPM32

S & F in repairs pressure control switch having ,IP 65 rating,dry running protection with automatic reset NoiselessDesigned for high start/stop per hour Built in thermal protection Make:Btalli,V guard,CRI

S & F in repairs film capacitors able to work on 440 V ,50Hz supply for motor run /start having following capacity complete all as specified and directed.Make:Epcos ,L&T,SH,Havells

6 micro farad

9 micro farad

12 micro farad

10 mili farad

20 mili farad

36 mili farad

45 mili farad

56 mili farad

60 mili farad

72 mili farad

76 mili farad

120 mili farad

150 mili farad

250 mili farad

S & F in repairs flexible cable 3 core copper cable of following capacity and size as per IS 694:

3 core 1.5 sqmm

3 core 2.5 sqmm

S & F in repairs 3 pin plug top 6 amps 240 V ISI approved plug top shock reistant and durable complete all as specified and as directed.

S & F in repairs bakelite plate not less than12 mm thick as the stand of 0.5HP and 1 HP monoblock pumpset installed at various locations complete all as specified and as directed.

M&L for Cleaning and redevelopment of existing borewells and with 250 psi and 750 cfm capacity air compressor (to get maximum yeild ) continously until clear water obtained all as specified and as directed by EIC. Note : Cleaning hours will be measured after the cleaning machine has gone to the lowest depth already achieved in the existing borewell.

Suppy and fix in repairs agitator shaft in the dosing tank made out of poly propylene rigid of dia 32 mm, length 500 mm with two bladed pitched blade turbine impeller with 3Nos. blades are welded to the shaft including removal of old unsv one complete all as specified and as directed by Engr -in-Charge and as approved by GE

Material and labour for preparation and painting of feeder pillar /outdoor & indoor LT starter panels/DG set at various places , old decorated surfaces by scraping rust , grease ,dust and old paints and applying one coat of red oxide two coats of synthetic enamel paint with spray painting complete all as specified and as directed. Note:The cost of taking up and refixing of switchgears,contactors and other electrical and mechanical parts is deemed included in the quoted rate. Make of paint: Berger Luxol,Asian Paints,Nerolac Paints

Supply and fix in repairs PVC two way MCB box with metallic din rail complete all as specified and as directed.Make:Havells,Legrand,Schneider

Taking up or down steel tubing and connections including cleaning for refixing or remove to MES store of following sizes complete all as specified and as directed.

15 mm bore

20 mm bore

25 mm Bore

40 mm bore

50 mm Bore

Taking up cast/ductile iron water mains (including all fittings), with spigot and socket ends and lead joints inluding burning out joints with recovering lead and setting aside for reuse or remove to MES store of following sizes:- Note :No extra payment will be made to contractor for excavation u/s old CI pipe of any size and will be included in the quoted rate complete all as specified and as directed.

80 mm dia bore

100 mm dia bore

Supply and lay medium grade galvanized pipe with all fitting such as tee, bends, union elbow reducer etc complete of following sizes all as specified and as directed.:- Make:Tata,Zenith,Jindal

15 mm bore

20 mm bore

25 mm Bore

40 mm bore

50 mm Bore

Supply, laying, jointing and testing of ductile iron (DI), pressure pipes with spigot and socket ends, centrifugally cast, class K-9, with cement mortar lining in inner side as per IS:8329/2000 (latest revision) and other relevant standards and metallic zinc coating followed by a finishing layer of epoxy paint in outer side, suitable for push on joint (rubber gasket joint) in any length with inside cement mortar lining laid in trenches complete all as specified an as directed for the following sizes Make:Shrikalahasti pipes Ltd.,Electrosteel casting Ltd,Saw Pipes.

80 mm dia bore

100 mm dia bore

M & L for Lathe work for pumpset shaft of any size complete all as specified and directed.

M &L for 3 position piano switch having three positions manual/off /auto for PB-88/200 inline booster pump complete all as specified and as directed.

S & F in repairs not less than 2 mm thick GI strainer for horizontal submersible pumps including necessary gI fittings, nut bolts, gasket, flange etc all as required at site complete all as specified an as directed by Engineer in charge for following sizes

40 mm bore

50 mm bore

80 mm bore

Supply and fix cast/ductile iron double office kinectic air release valve for fixing on 150 mm bore CI/DI line type DK PN 1.0 with flanged ends and SS floats as per D IS:14845 including all necessary earth work and accessories complete all as specified and directed by Engr-in-Charge including taking up old u/s valves and depositing the same at AGE E/M storeyard.Make:Kirloskar,L& T,BIR

Supply and fix in repairs float switch sensor having PVC body with 1 mtrs 2.5sqmm 2 core included cable working on 8 Amps 240 Volts 50Hz complete all as specified and as directed.

Supply and fix in repairs stainless steel water pressure gauge having pressure range 0- 25 Kg/sq cm having socket for 15 mm with necessary SS pipe of length approx 30 cm and hudraulic isolation valve necessary including removal of old unserveceable one complete all as specified and asdirected.Make:H guru, Wika,Baumer

Supply and lay in repairs 3- layer PP-R Polypropylene random copolymer) pipes SDR 7.4 & SDR 11 UV of following sizes fixed complete to walls, ceilings or in floors,laid in trenches etc. with all fitting such as tee, bends, union, elbow reducer, pasting adhesive materials etc with outer dia of pipe 63 mm complete all as specified and as directed. Make:Finolex,Prince,Kisan,Supreme

Note : 1. Performance security:- Refer Condition 22 of Special Conditions. 2. Quoted Contract Sum shall be arrived at after deducting the amount of Credit Schedule (refer Schedule of Credit in pdf form for quantity, rate and amount etc.) for old unserviceable materials retrieved from site. 3. The site is in scattered area. The building(s)/site(s) shall be handed over in phases and the contractor will have to arrange his working programme accordingly. No claim whatsoever for not giving the entire site on award of work and for giving the site gradually will be admissible, except granting fair and reasonable extension of time.

purva engineears and contracters

Goodluck Enterprises