Construction of guest room at Manaykhang Tegar. (Under District Capex)

Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres: All kinds of soil :

Dry stone pitching (any thickness) excluding cost of stones. On Horizontal

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : 7.1.1 Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attachedpilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers,abutments, posts and struts etc. above plinth level up to floor five level,excluding cost of centering, shuttering, finishing and reinforcement 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve Workability without impairing strength and durability as per direction of Engineer-incharge. Note: - Cement in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is content considered payable or recoverable separately. All works above plinth level upto floor V level

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering and shuttering including strutting, propping etc. and removal of form for a) Foundations, footings, bases of columns etc. for mass concrete

Columns, pillars, piers, abutments, posts and struts.

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Suspended floors, roofs, landings, balconies and access platform

Edges of slabs and breaks in floors and walls: Under 20 cm wide.

Providing & fixing upto floor five level compressed stabilized earth blocks (CEB) made an appropriate mix of dry inorganic subsoil, non-expansive clay, sand, and aggregate with 5% cement as stabilizer, in cement mortar, including cost of materials complete.

Providing and fixing thermal insulation with Resin Bonded Fibre glass wool conforming to IS: 8183 havingdensity 24 kg/m3, 50 mm thick, wrapped in 200G Virgin Polythene Bags fixed to wall with screw, rawel plug& washers and held in position by criss crossing GI wire etc. complete as per directions of Engineer-in- Charge.

Providing and fixing up to floor five level precast cement concrete solid block, including hoisting and setting in position with cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centering, shuttering complete.1:3:6 (1 cement : 3 coarse sand : 6 graded crushed stone aggregate 20 mm nominal size

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): Second class kail wood.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windowscomprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profilesduly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriatedimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated)casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plasticcaps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusionwelded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixinghardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wallshall be filled with weather proof silicon sealant over backer rod of required size and of approved quality,all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes andsilicon sealant shall be paid separately). Variation in profile dimension in higher side shall be acceptedbut no extra payment on this account shall be made For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth& width of profile shall be acceptable.uPVC profile should be tested by BSI(UK) & SKZ(Germany) @25000 weathering hours Casement window single panel with S.S. friction hinges (300 x 19 x 1.9 mm), made of (small series) frame 47 x 50 mm & sash 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glass pane glazing bead of appropriate dimension. (Area of window upto 0.75 sqm.)

Providing and fixing double glazed hermetically sealed glazing in aluminum windows, ventilators and partition etc. with 6mm thick clear float glass both side having 12mm air gap including providing EPDM gasket, perforated aluminum spacers, desiccants, silicon sealant (both primary and secondary sealant) etc. as per specifications, drawings and directions of Engineer-in-charge complete

Providing and fixing cupboard shutter with 19mm thick one side decorative and other side balancinglamination factory pressed BWP grade marine ply as per IS 710 of approved brand including 2mm thickPVC edge banding tape with hot glue by edge bending machine etc. with auto closing spring loadedhinges (hydraulic type) etc. complete as per direction of Engineer-in-charge.(Payment of providing andfixing auto closing hinges shall be paid separately)

Providing and fixing of 1mm thick sunmica laminate sheet of of approved brand over plywood for making cupboards, including cutting, positioning and finishing as per engineer incharge all complete.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

20mm Cement plaster of mix: 1 : 4 ( 1 cement : 4 fine sand).

15mm Cement plaster on the rough side of single or half brick wall of mix: 1 : 4 ( 1 cement : 4 fine sand).

6 mm cement plaster to ceiling of mix 1 : 3 (1 cement : 3 fine sand)

Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 2 mm thick.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer

Finishing walls with water proofing cement paint of required shade : New work (Two or more coats applied @ 3.84 kg/10 sqm)

Rough cast plaster upto 10 m height above ground level with a mixture of sand and gravel or crushed stone from 6 mm to 10 mm nominal size, dashed over and including the fresh plaster in two layers, under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand) and top layer 10 mm cement plaster 1:3 (1 cement : 3 fine sand) mixed with 10% finely grounded hydrated lime by volume of cement. Ordinary cement finish using ordinary cement

Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand and manufacturer, in all colours and shades, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalen

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc. including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete ,including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size).

Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stoneaggregate) finished with a floating coat of neat cement including cementslurry and curing complete, but excluding the cost of nosing of steps etc.complete. 50 mm thick with 20mm nominal size stone aggregate.

Providing and laying prelaminated flooring of approved brands like Green Panel, Action Tesa AC3 including wooden beading, foam complete.

Providing and fixing wall panelling with T&G panel of spprove brand including 12 mm ply backing and polishing with approved brand. Complete job.

Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m . All kinds of soil

Providing and fixing traditionally carved wood work (Shingstak) over doors and windows including all accessories as per the direction of the Engineer in-charge, complete with;Budloo wood

Carriage of Sand and C.Agg from an average lead up to 10km by mechanical transport.

Carriage of Stones from an average lead up to 10km by mechanical transport.

Providing and fixing precoated galvanised iron profile sheets (size, shape andpitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) totalcoated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpasteel grade, 5-7 microns epoxy primer on both side of the sheet and polyestertop coat 15-18 microns. Sheet should have protective guard film of 25micronsminimum to avoid scratches during transportation and should be supplied insingle length upto 12 metre or as desired by Engineer-in-charge. The sheet shallbe fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDMseal, complete upto any pitch in horizontal/ vertical or curved surfaces, excludingthe cost of purlins, rafters and trusses and including cutting to size and shapewherever required.

Sanitary Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral 3type foot rests.

Providing and fixing vitreous china dual purpose closet suitable for use as squatting pan or European type water closet (Anglo Indian W.C pan) with seat & lid fixed with C.P. brass hinges and rubber buffers, 10 litre low level flushing cistern with fitting and brackets, 40 mm flush bend, 20 mm over flow pipe, with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: White vitreous china dual purpose WC pan with white solid plastic seat and lidwith white vitreous china flushing cistern and C.P. flush bend.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps.

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception ,, of pipes and fittings:

Providing and fixing G.I inlet connection for flush pipe connecting with W.C pan.

Providing and fixing 8 mm dia C.P /S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to European type W.C of quality and make as approved by Engineer – in – charge.

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes SDR 7.4 U V stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Chajge. (Concealed work including cutting chases and making good the walls etc.,)PN-16 Pipe, 25 mm OD (SDR-7.4)

PN-16 Pipe, 40 mm OD (SDR-7.4)

Providing and fixing PVC soil waste and vent pipe of required dia including bends, Tee door bend, L bend trap jointed with addisive material ISI marked like Prince vector or equvilent brand including labour charge. all complete a) 110mm

Providing and fixing toilet paper holder c.p brass

Providing and fixing PTMT soap dish holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106gms.

Towel rail C.P. brass 750 x20 mm together with a pair of C.P. brass brackets to fit the size of towel rail.

Providing and fixing PTMT - Towel Ring 215x200x37 mm

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P brass screw and washers complete.

Providing and fixing CP brass basin mixer pillar tap of approved quality and make.

Providing and fixing CP brass wall mounted basin mixer pillar tap of approved quality and make

Providing and fixing CP brass bib cock of approved quality and make

Providing and fixing CP brass stop cock of approved quality and make

Providing and fixing floor jalli

Constructing masonry Chamber 60x60x75 cm, inside with 75 class designation brick work in cement mortar 1:4(1 cement : 4 coarse sand) for fire hydrants, with C.I. surface box 350x350 mm. top and 165 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) necessary excavation foundation concrete 1:5:10 (1 cement: 5 fine sand: 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement: 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design :

Providing and fixing P.V.C waste pipe for sink or wash basin including P.V.C waste fittings complete. Flexible pipe 32 mm dia.

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour: Waste coupling 3.1 mm of 79 mm length and 62 mm breadth weighing not less than 45 gms.

Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931.

Providing and fixing 15 litre geyser of approved brand and manufacture.

Providing and fixing of material for the insulation of pipe with nitrile tube, tapping with cello tape, Rockwood 6 inch per side, wire mesh , polythene, tapping with cello tape aluminium sheet 26 guage cladding with dia complete job including carriage 25mm

providing and fixing heat tape 33 watt on PPR pipes made of denforced or chromelox or equivalent make , as approved by Engineer in charge , Complete Job.

providing and fixing of material for the insulation of Water storage tank with nitrile sheet , tapping with cello tape, Rockwood 6 inch per side, wire mesh polythene, aluminium sheet 26 guage cladding with dia of complete job 19mm thick nitrile sheet.

Providing and fixing gate valve (PPR) of approved quality, High or low pressure, with plastic floats complete. 40 mm nominal bore.

Providing and fixing ball valve (PPR) of approved quality, High or low pressure, with plastic floats complete. 32 mm nominal bore.(PPR)

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Providing and fixing double equal plain junction of required degree:75x75x75mm

Providing and fixing of 1.5 Hp self priming regenerative electric motor water pump, of a brand approved by the engineer incharge, complete job.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including

Providing and fixing Stainless Steel AISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever require 510x1040 mm bowl depth 250mm.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.Group A

Group B

Group c

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface /recessed medium class PVC conduit alongwith 2 Nos. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.75 mm X 75 mm X 60 mm deep

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6A switch

15/16 A switch

3 pin 5/6 A socket outlet

6 pin 15/16 A socket outlet

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.3 Module (100mmX75mm)

4 Module (125mmX75mm)

6 Module (200mmX75mm)

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.3 Module

4 Module

6 Module

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required.

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)6 way , Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

Single pole and neutral

Double pole

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.63A

Supply of 9-10W LED downlight recess mounting luminaire, Aluminium powder coated white after phosphochromate treatment with system lumen efficacy of >100lm/W to enhance the lumen output with Output Short-circuit protection, Surge protection. Lumen Output of 1000 lumens.CRI >80, Color temperature 5700K, THD <10% and PF >0.95,IP20,Life class of 50,000 hrs @ L70, Input Supply Voltage Range:140-270 V, Frequency :50-60 HZ; Internal Surge Protection:3 KV. Havells Cat Ref- INTEGRAHEDLR10WLED857S or similar from approved makes 9-10W Surface Mouted

Supply of 18-20W LED downlight recess mounting luminaire , Aluminium powder coated white after phosphochromate treatment with system lumen efficacy of >100lm/W with Output Short-circuit protection, Surge protection . Lumen Output of minimum 1800 lumens.CRI >80, Color temperature 5700K, THD <10% and PF >0.95,IP20,Life class of 50,000 hrs @ L70, Input Supply Voltage Range:140-270 V, Frequency :50-60 HZ; Internal Surge Protection:3 KV. Havells Cat Ref- INTEGRAHEDLR18WLED857S or similar from approved makes 18-20W Surface Mouted