EXTERNAL PERIODICAL SERVICES INCL CONNECTED SERVICES

Amount

M&L for preparation of old decoreated external wall / Ceiling surface of existing treatment by scrapping with TruCare Wall Sander : L-01/H-01 (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 80 Grit having dia of 7”/9” to make the surface free from dust, loose paint etc. or equivalent makes viz Xpress sanding machine having suction vaccum bag or by manual scrapping tools where mechanical removal is not possible and applying and applying two coats of weather proofing exterior acrylic emulsion paint over priming coat premium quality over wall / ceiling complete all as specified and as directed by Engr- in-charge. Note :- The work shall be executed up to G+ 8th floor Height

M&L for applying of 1 mm thick wall care putty over prepared surfaces of new/old walls/ceiling including sanding of putty surface properly with regmar to make the surface free from dust or loose particles. Complete all as specified and as directed by Engr- In - Charge. (The work shall be executed up to G+ 8th floor Height)

M&L for preparation of old decoreated external wall surface by mechanised sander of Berger paints or equivalent makes viz Xpress sanding machine having suction vaccum bag or by manual scrapping tools where mechanical removal is not possible, and applying two coats of cement base paint over coat of primer on walls complete all as specified and as directed by Engr- in-charge.

Taking down cement or lime plaster any description on brick or stone walls etc including recking out joints hacking for key scrubbing down with waters etc.

M & L for rendering 15 mm thick in cement mortor 1:4 on brick/ concrete surfaces with water proofing compound and finishing the surface even and fair without using extra cement complete all as specified directed.

Supply only liquid Water proofing compound.

M&L for prepration of newly plastered surfaces of wall and applying two coats of cement base paint over a coat of Primer complete all as specified and directed .

M&L 10 -12mm thick polymer modified readymix cement base plaster as per manufacturer instruction on fair / unfair faces of brick work or concrete surfaces & finishing the surface even & smooth as per manufacturer instruction complete all as specified & directed.

M&L for prepration of new plastered surfaces of wall/ Ceiling and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new/ Old surfaces. complete all as specified and directed.

M&L for Rendering 5mm thick with water proofing compound in cement mortar 1:3 on fare faces of brick work or concrete surfaces and finished the surface even and smooth without using extra cement in ceiling/ Chajjas complete all as specified.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specifed and directed.

M & L for providing RCC 1:2:4 type B- 1 using 20 mm grade stone aggregate as in slab supportetd on walls, shelves, Chajjas, cantilevers or similar work complete all as specified and as directed.

Formwork to Chajjas through and similar items including edges and similar work complete allas specifiede and as directed.

M&L TMT bars 10mm dia and over in reinforcement cut to length bent to shape required incl hooking ends and binding with MS wire (annealed) not less than 0.9mm dia all as directed and specified.

Demolition in cement concrete of cement concrete in ground floor and paving not exc. 15 cm thick below or above ground level all as specified

M&L for 75 mm thick in Plain cement concrete type C2 (1:3:6) (using 40 mm graded aggregate) as in plinth protection and sub base laid in alternate bays (not exceeding 2 Sqm each) finished even and smooth at top without using extra cement and providing joints throughout the thickness of plinth protection, filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight all as directed at site.

S&F in repair rotantional moulded polythylene water storage tanks 1000 ltr capacity (cylindrical vertical with closed top ) hoisted and fixed in position complete with ball valve of high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball and screwd for iron pipe 20mm bore omplete all as specified and directed.

S&F in repair rotantional moulded polythylene water storage tanks 500 ltr capacity (cylindrical vertical with closed top ) hoisted and fixed in position complete with ball valve of high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball and screwd for iron pipe 20mm bore omplete all as specified and directed.

Taking up or down steel tubing 15 mm bore and connection including cleaning for refixing. complete all as specified and as directed by Engineer-in-Charge

Taking up or down steel tubing 20 mm bore and connection including cleaning for refixing. complete all as specified and as directed by Engineer-in-Charge

S&F steel tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floors, bore of pipe 15 mm dia.including making hole in RCC slabs for vertical pipes & making good the same with Cement Concrete I:2:4 complete all as specified and as directed by Engineer-in-Charge

S&F steel tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floors, bore of pipe 20 mm dia.including making hole in RCC slabs for vertical pipes & making good the same with Cement Concrete I:2:4 complete all as specified and as directed by Engineer-in-Charge

Demolition of stone slab and tiles of any description or thickness laid bedded and pointed in any mortar in floors, aprons etc complete all as specified and directed.

M&L for granite (of any type) work ( table rubbed and polished ) in steps, jambs,pillars, cooking platform and like in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

M&L for Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specifed and dircted .

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering complete all as specified and as directed.

S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour as approved having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and including cutting chasing of wall, complete all as specified and directed.

Demolition of brick work/stone bulder measonary built in cement mortar or cement lime mortar of any description and in any position all as specified.

M&L for brick work in CM (1:4) straight or curved on plan exc 6.0m mean radius and using old size sub class 'B' bricks all as specified.

.-ditto- all as per item No 48 above but except bricks

M&L for Brickwork with sub-class `B' brick straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed

S&F in repair for 2 mm thick Plain colour PVC sheet fixed with screw over any type of MS/steel gate grill etc. omplete all as specified and directed.

S&F in repair MS framed work as in door or gates of angle or other section with gusset plates,rail, braces,etc and similar work incl primer conform-ing to Fe 410-W (Gde-E- 250) quality-B complete.

S&F in repair 1.00 mm thick plain black steel sheet in hearths; covering to door shutters; covering to doorchowkats (frames);chullah hoods; water tanks; water troughs;ducts; urinal troughs and funnels, etc. cut to size edges beaded if directed, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40 mm lap joints or welded/ riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required incl priming complete all as specified and directed.

M&L for preparing new Steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamalle paint over a coat of red oxide zink chrome primer. complete all as specified and as directed.

Cleaning exposed mineral substrate like stone/ Grit Waseh/ Bric/ Concrete/ Cement paint and removing dirt, dust , bird dropping grease, oil, algae, fungus, vegetable growth etc, including providing, applaying cleaning chemical agents where ever required, with fine silica, mixing it with clean water, wthout causing any scratching /damag to the surface. And then after providing and applying breathable, non-film forming, non-reactive, antifungal and water repellant silane/siloxane silicaone chemical as approved by Archaeological Survey of India/Engineer-in-Charge, of approved brand and manufacture, diluted with solvent Mineral Tupentine Oil in the ratio of 1:12 (One part of approved chemical :12 part of Mineral Turpenting oil), on the existing masonry surface with two coat at wet on wet woriking to give uniform application of ready to use chemical, all complete as pwe direction of Engineer-in-Charge (The Rate is inclusive of all materials & labours involved with scafolding).

Taking down old cement plaster/Grit wash on stone wall or brick surfaces of walls including raking out joints, hacking for key and scrubbing down with water complete and M&L for washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement 4 coarse sand) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement 1/2 coarse sand and 2 stone chipping 10mm nominal size) in pannels wih grooves all aroud as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chipping complete all as specified and directed.

Forming grooves of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved paltern using wooden batters nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specification and directions of the Engineer-in-charge.

M&L for injecting chemical GLYPHOSPHATW 41% SL 20 ml or till refusal by makimg cut/ injection in the stem of plant 30mm C/C spraying with solution (25ml Glyphospoto 41% diluted with one litre water) and removing the plants/ vegetation uptofive story height including penefreated roots complete including necessary scaffolding etc complete all as per specification and directions of the Engineer-in-charge.

M&L for Complete removing existing treatment of plastered or unplastered Old surface of wall and applying Two or more coats of 100% Premium weather proof exterior emulsion paint with Graco 490 spray machine, having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance, as of required shade (Company Depot Tinted) with silicon additives @ 5-6 sqm/ltr over and including priming coat of exterior primer applied @ 1 litre/ 10 sqm over surfaces including change of existing colour, if required complete all as specified and as directed. Note:- Application to be done only by applicator authorised by manufacturer.

Supply and application of synthetic intermediate finish designed with high quality exterior durable acrylic modified resin and special quality quartz, with trowel to achieve thickness of 1-1.5mm @3sqft/kg, over a coat of Trucare exterior wall primer to be done @1ltr/10sqm, followed by 2-3 coats of GreenPro certified 100% Acrylic smooth emulsion Ultima Suprema with silicon additives @2ltr/10sqm with Graco-490 to achieve uniform shade as approved by engineer in-charge. Application to be done only by applicator recommended by manufacturer to provide a paint performance warranty of 8 years

Dismantling/ taking out of existing roof tretment with APP membrane of any thickness including taking out existing sreed bed / rendering of any thickness wth all necessary arrangements complete all as specified and as directed.

M & L for providing and applying smart care Dampproof, a fibre reinforced elastometric liquid water proofing membrane formulated with reinforced acrylic fibres having Sun Reflective Index (SRI) of 105 on horizontal/ vertical surfaces of roof/ wall/ chajjas in multiple costs @2.0 litre/ sqm. Primary coat is self-priming coat of elastomericwaterproofing liquid (Dilition with water in the ratio of 3:1, damp proof : Water) and other coat to be applied undiluted. The coating needs to be reinforced with 40GSM Geotextile, to sandwiched between 2nd &3rd coat of coating. The application shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes complete in all respect as per the direction of Engineer-in-Cgarge. Make : SmartCare Damp Proof of Asian or equivelent in Berger/ Nerolac/ STP only. Notes: (1) The work shall be executed through authorised appplicatot of manufacturer only. (2) Authorised Applicator shall be approved by GE befor starting the work. (3) All materials shall be produced directly from manufacturer. The purchase voucher shall be produced to the Engineer-in-Cgarge for his verification of material. Engineer-in-Cgarge shall deface the original purchage vouchers. (4) Guarantee: The contractor shall furnish a written guarantee for the effectiveness of the water Proofingtreatment for a period of Eight years i fevour of GE. A sum equivelent to 2.5% ( Two point five Percent) of the cost of water proofing treatment shall be retained by the Govt from the contractor's duues as security deposite. The contractor may, however, furnish a fixed deposite receipt in lieu from a Schedule bank pledged in fevour of Garrison Engineer.

M&L for PCC 1:2:4 type B -1 (using 20mm graded crushed stone agregate) as in roof slop and required, brushing neat cement slurry with 3.0kg of cement per sq. metre including necessary form work and scaffolding upto 2nd floor here required to match the existing surfaces rounded orchamfered on edges complete all as specified and directed.

M & L for priming over roof surface @ 0.25 Ltr/Sqm over a cleaned roof surface and applying one coat of bitumin painting with hot blown grade bitumin 85x25 @ 1.20Kg/ Sqmtr and laying of APP based polymetric membrane minium weight 3kg/ sqm and minimum 3mm thick reinforced with polyster non wove febric ( wt not less than 150gms/ sqm) laid on primed surface by forced application complete all as specified and directed.

M&L for preparation and applying two coats of aluminium paint over APP based polymetric membrane with required finishes complete all as specified and as directed.

Demolition and breaking up drain pipes (SGSW, AC, PVC or reinforced cement) set in cement mortor internal dia of pipe 75 to100 mm complete all as specified and directed.

S&F of 110 mm bore SWR pipes single socketed in any length with rubber ring joints fixed to walls ,floors, trenches etccomplete all specified and directed.

-ditto- all as per item No 48 above but 75 mm dia PVC SWR pipe.

S&F 110 mm bore PVC (SWR) bends with rubber ring joints fixed to walls complete all as specified and directed.

-ditto- all as per item No 50 above but 75 mm dia PVC SWR bends.

Disconnecting existing tanks exc 250 ltr n exc 500 ltr capacity, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position.

Disconnecting existing tanks exc 500 ltr n exc 1000 ltr capacity, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position.

S&F in repair Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture1.4mm and fixed with stainless steel wire staple fixed with aluminium beading etc complete all as specified and as directed in upto 8th floor Height.

M&L in repair for 4 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified and directed.

S&F in repair 3mm thick Figured glass, pin head type and glazing with oil putty in square n. exc 0.80 Sqm in each panes fixed any bldg hight complete all as specified and directed in upto 8th floor Height.

Preparation of old painted surfaces of wood work of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

All as per item No. 57 above but on steel surfaces complete all as specified and directed.

tarun construction co (BID ID -3122137)

M/S Chhavi Constructions Co (BID ID -3123012)

M/S SHRINARAYAN MEENA (BID ID -3123020)

M/S Rohit Enterprises (BID ID -3123872)

M P TYAGI ENGINEERS AND CONTRACTORS (BID ID -3120151)

V M CONSTRUCTION (BID ID -3116528)

MAA SANTOSHI ENTERPRISES (BID ID -3122906)

M/S Parshant Associates (BID ID -3122864)

POONAM ENTERPRISES (BID ID -3120955)

A R construction (BID ID -3123576)