Providing Ceramic Tiles in House No. 60 and 65 in Officer Colony No. 4 at Gurguram (Recall)

Amount

Providing & fixing ceramic tiles/ anty skid tile of size 400mm X 400mm of approved make in flooring laid in any pattern as specified over base of 20mm thick cement coarse sand mortor 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles Note:- Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO,KAJARIA,SOMANI,ORIENT Bell, JONSONS , RAK & SIMPOLO(HSR 14.91) Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material

Providing & fixing vitrified tiles of size 600mm X 600mm of approved make in skirting/dados laid in any pattern as specified over base of 20mm thick cement coarse sand mortor 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles(HSR 14.90) .ote:- Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO,KAJARIA,SOMANI,ORIENT Bell, JONSONS , RAK & SIMPOLO(HSR 14.90) Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material

Providing & fixing Ist quality ceramic glazed wall tilesconfirming to IS 15622 (thickness to be specified by manufacturer)of approved make in all colors,shade except burgundy,bottlegreen,black of any size as approved by engineer-In Charge in skirting ,risers of steps and dados over12mm thick bed of cement mortor 1:3 coarse and jointed with grey cement slurry,including pointing in white cement mixed with pigment to match the shade complete. Size of ceramic Glazed tiles 300mm X 450mm(HSR 14.92 b) Note:- Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO,KAJARIA,SOMANI,ORIENT Bell, JONSONS , RAK & SIMPOLO Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material

Factory manufacture solid flush door and Shutters, with block board core as per I.S. No. 1659-1969 bonded with water poof type phenol formal dehyde synthetic resin, hot-pressed, conforming to I.S. 2202 part I and II, fixed in positon includeing iron hinges, screws, chocks/cleats and stops etc. (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position)- as per HSR 17.93 a iii. (Note) :- Commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminated core and lipped edges. (Duro, Green) 35 mm. Thick (HSR 17.93a iii- note I under 17.18))

Factory manufactured wire gauze door and window shutters of commercial hard wood such as hollock, champ, chikrassy annd chaplash, etc. (non coniferous timber other teak conforming to I.S specification no. 1003, kiln seasoned) with 100 mm wide vertical styles, 150 mm wide lock rail 200 mm wide bottom rail, and wire gauze of 140 G or 120 G designation including cost of iron hinges, screws, chock/cleats, stops nails etc. complete fixed in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position) (i) 30 mm thick (HSR 17.92 (i) - Note I under 17.18

Providing and fixing sliding bolt with nuts and screws etc. complete- aluminium- size 300 mm x 16 mm(HSR 17.83b-i)

Cost of aluminium fitting cokmplte for doors and windows, such as tower bolts, handles, etc., and screws for these fittings (excluding sliding bolt)- for single lead shutter(HSR 17.72a)

Providing and fixing commercial type block Board, plain lining, butt jointed, including Wooden plugs (teak) placed at 45 cm to 60 cm centres, complete with necessary nails (frame work shall bepayable extra)-19mm thick(HSR 17.49 b)

PROVIDING AND FIXING IN POSITOIN BEST INDIAN MAKE (to the approval of the Engineer-in-charge). INDIAN TYPE ORISSA OR ORYA WATER CLOSET SUITE for Sinking into floor, with raised foot treads COMPLETE WITH 100 MM H.C.I, ‘P’ TRAP with or without vent as required & all other necessary fittings as fully described in item No. 30.1 above Size 580 mm white (HSR 30.2a-i)

EXTRA OVER item nos. 30.3 to 30.6 FOR PROVIDING AND FIXING BEST INDIAN MAKE PLASTIC HYGENIC SEAT with lid complete instead of hollow Black or white plaster seat and lid. White plastic seat (Solid)(HSR 30.13 i)

PROVIDING AND FIXING IN POSITION INDIAN MAKE (ORDINARY) LAVATORY SUITES Consisting of Lavatory in VITREOUS CHINAWARE size as given Below (to the approval of the Engineer-in-charge) including china plug for tap hole where necessary; R.S or C.I Brackets for building into wall including paints. 30 mm C.P Brass waste with C.P Brass chain & rubber plug. 15 mm C.P Brass screw down pillar tap with jamuts or couplings best design (As approved by Engineer in Charge) All fittings best India make & to the approval of athe Engineer in Charge. All brass work chromium plated & complete in all respects including cutting & making good the walls, floor & painting of fittings etc. White. Size 550 mm x 400 mm with one no. tap(HSR 30.41 iv)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE BEVELLED EDGE 5.5 MM THICK MIRRON Mounted on ASBESTOS sheet GROUND FIXED IN POSITION BY MEANS OF 4 NOS. CHORMIUM PLATED BRASS SCREWS AND WASHERS over rubber washers and rawl plug embedded in the wall or choromium plated brass clamps with C.P Brass screws (as required by the Engineer in Charge) complete including cutting & making good the walls etc. (India Make ) 600mmx450mm(HSR 30.71a-i)

Providing and fixing in position 15 mm i/d C.P brass bib Cocks of best quality (as required by Engineer-in-charge) Bib Cock(HSR 30.75C)

Providing and fixing in position C.P brass stop cocks (as Approved by the Engineer-in-charge) 15 MM STOP COCK Stop cock male and female end(HSR 30.76a-i)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE FLEXIBLE TUBE CONNECTION C.P Brass 15mmx450mm(HSR 30.82 b-iii)

Providing and Fixing HDPE WATER STORAGE TANKS of Sintex, Diplast, O.K. Supreme make with covers/lids marked with IS:12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow and scour provisions with suitable plug on scour pipe including cost of nipples, washers flags for connection in tanks complete in all respects to the satisfaction to the Engineer-In-Charge. (HSR-30.119)500 ltr.

Recovery Items:-Bidder have to quote rate for recovery items at least or more than reserve price. The rate quoted against recovery items will not be included in the total amount rather it will be deducted while calculating financial statement of the agency.T Note:- The reserve rate/amount is minimum amount to be used as base for quoted purchase rate by the agency. No rates/amount below the reserve price will be entertained and reserve price will be considered for all purposes in case the agency quotes lesser than reserve price.-- Flush Door @ 20 KG

Window @ 20 Kg

Note 1 :-In case of any difference in the unit & nomenclature of any of the HSR/DSR items of civil,PH work depicted in this DNIT and that given in HSR,the unit and nomenclature given in HSR shall be applicable. 2. Only reputed make material will be used (Make/brand exhibited in HSR/DSR and exhibited in approved standard documents) as approved by the Engineer-in-charge,while executing various items/work at site. 3. The agency to whom the work is allotted have to produce original bill/ voucher for all qty in taken of proof of Purchase of material