SPECIAL REPAIR TO CERTAIN SMQ AT VARIOUS POCKETS OF AIR FORCE STATION MUMBAI UNDER GE AF THANE

Amount

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15cm thickness (below or above ground level) complete all as specified and as directed by Engr-in- Charge.

M&L for providing 75 mm thick PCC (1:3:6) type C2 using 40 mm graded aggregate as Path/Plinth protection finished the surface even & smooth with out using extra cement complete all as specified and directed by Engineer in charge.

M&L for Hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as directed by Engr-in-Charge.

Dismantling floor, hearth or wall tiles laid, bedded, pointed in any mortar of any description or thickness in floors, aprons etc. complete all as specified and directed by Engineer in charge.

M&L for Cement concrete75 mm thick, type D2 1:4:8 (40 mm graded aggregate)in sub base , filling and mass-concrete complete all as specified and as directed by Engr-in- Charge.

M&L for coloured Non skid vitrified exterior tiles of size 400x400mmx10 mm thick in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 15 mm thick screed bed in CM (1:4) complete all as specified and directed by Engr-in-Charge.

M&L for joint free Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm in size, such as Skirting, Dado, etc,over and including 10mm thick rendering in cement mortar 1:3 Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the shade of the Tiles, complete all as specified and as directed.

Taking down cement plaster any description on brick/ block/ stone walls, roof etc. including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by Engineer in charge.

M&L for 15 mm thick rendering in cement morta 1:6 on fair faces of brick or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed by Engr-in- Charge.

M&L for rendering in two layers on external surfaces first layer 15mm thick in CM 1:6 on fair faces of brick/PCC block or concrete surfaces and second layer ( setting coat / finishing) 5mm thick in CM 1:4 with approved water proofing compound finished even and smooth without using extra cement complete all as specified and directed by Engr-in- Charge. (Note:- WPC shall be measured and paid seperately)

Supplied only water proofing admixture etc complete all as specified and directed by Engineer in charge.

M&L for 10 mm thick rendering in CM 1:4 on broken chajjas / facia / walls /ceilings etc, area n. exc 3 sqm each patch (in repairs) , includings finishing to match with existing surfaces without using extra cement complete all as specified and directed by Engr-in- Charge.

M&L for applying two coats of oil bound distemper over a coat of primer,over 1mm thick wall care putty on walls including preparation of new or previously untreated surfaces alongwith all necessary steel scaffolding for erection complete all specified and directed by Engr-in- Charge.

M&L for applying two coats of oil bound distemper over a coat of primer,over 1mm thick wall care putty on ceilings including preparation of new or previously untreated surfaces complete all specified and directed by Engr-in- Charge.

M&L for applying two coats of whitewash over a coat of primer, on old plastered surfaces including preparation of new or previously untreated surfaces complete all specified and directed by Engr-in- Charge.

M&L for applying two coats of weather coat exterior emulsion paint over a coat of alkali resistant primer including preparation of old surface of walls and complete removal of existing treatment including all necessary steel scaffolding for erection complete all as specified and directed by Engr-in- Charge.complete all as specified and directed by Engr-in-charge.

M & L for Preparation of old plastered surfaces/ unplastered surfaces including brooming down with steel wire brushing scrapping down smoke spout moulds, moss and efflorescence, salt treating oil and greasy spots etc and applying one coat of weather coat exterior emulsion paint over a coat of alkali resistant primer on old plastered surfaces of on walls,soffits of slabs, chajjas including all necessary steel scaffolding for erection complete all as specified and directed by Engr-in- Charge.complete all as specified and directed by Engr-in-charge.

M&L for applying two coats of white wash including preparation of new or previously untreated on ceilings surfaces complete all specified and directed by Engr-in- Charge.

M&L for complete removal of exiting treatment on wooden surfaces of any description and applying one coats of synthetic enamel paint over a coat of primer including cleaning and preparing the surface complete all as specified and as directed by Engr-in-Charge.

Taking down Chowkhats or frames without taking of shutters exc 1.5 sq. m but not exc 4 sq. m each complete all as specified and as directed by Engr-in- Charge.

Taking down Shutters of any description exc 1 sq. m and not exc 2 sq. m each complete all as specified and as directed by Engr-in- Charge.

Repairs to aluminium window shutters of any description easing & adjusting without taking shutters exc 1 Sqm and not exc 2 Sqm each complete all as specified and directed by Engr-in- Charge.

S & F second class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered put together with glue pinned at joints complete all as specified and directed by Engineer in charge.

S & F 30 mm thick flush shutter water proof BWR grade solid core construction with block board core and ply wood face panel commercial type both sides complete all as specified and as directed by Engr -in - Charge.

S&F for 35mm thick IInd class hard wood glazed and skelton shutters divided into squares with plain chamfered or reounded miltred and related sash bars number to received glass gauze etc edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR Part-I section 8 clause 8.20(a) supplied and fitted to chowkats complete complete all as specified and as directed by Engr-in-charge.

S&F for 30mm thick IInd class hard wood glazed and skelton shutters divided into squares with plain chamfered or reounded miltred and related sash bars number to received glass gauze etc edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR Part-I section 8 clause 8.20(a) supplied and fitted to chowkats complete complete all as specified and directed by Engr-in-charge.

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube in opening as per specification & drawing complete all as specified and directed by Engr-in- Charge.

S&F Factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of ms tubes for top &bottem rails, ms frame shall be covered with heat moulded plain colour PVC 'C' channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour pvc sheetfor top rail ,lock rail, &bottem rail, on either side & as gap insert for top rail , panneling of plain colour pvc sheet to be fitted in the ms frame welded /sealed to the stiles & rails with suitable pvc sheet beading, & jointed together with solvent cement suppling & fixing in the frame at site complete all as specified and directed by Engr-in-Charge.

S&F in repairs 250 mm long aluminium anodised sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed by Engineer in charge.

S&F in repairs300 mm long amild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by Engineer in charge.

S&F in repairs300 mm long amild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by Engineer in charge.

M&L for 25 x 3mm FI holdfast complete all as specified and directed by Engineer in charge.

Cutting holes in brick walls built in cement mortar depth of embedded portion of hold fast or lugs measured from the face of the jamb into the wall exc half brick wall not exc one brick wall and rendering, cutting out branch channel and making good to pipe and rendering complete all as specified and as directed by Engr-in- Charge.

M&L for preparing surfaces of wood and treating with tar or coal tar black paint to ends of post back side of chowkats etc 0.10 sqm but not exc 0.50 sqm complete all as specified and as directed by engineer in charge

S&F mild steel 100 mm long butt hinges, medium weight cold rolled complete all as specified and directed by Engineer in charge.

S&F 150 mm extruded aluminum alloy handles, cast type, anodized complete all as specified and directed by Engineer in charge.

M&L for preparation of new untreated wooden surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified and as directed.

S&F for floor door stopper of brass body and tongue, anodised with hard drawn steel spring, fixed in floor complete all as specified and as directed by Engr-in- Charge.

S&F vitreous china squatting pan of water closet (Orrisa pattern) size 580mm x 440 mm white with integral foot rests complete connection to drain ( outgoing pipe) and to flushing pipe of 32 mm dia and syphonage pipe etc and making good the floor with provn of concrete bedding in repair complete all as specified and as directed by Engr-in- Charge..

S&F, as in repair, vitreous china wash basin, white flat back size 630x 450 mm, excluding taps, waste chain, plug and porcelain stopper but including brackets, cutting for and pinning in ends of bracket or erecting stand alongwith 32mm PVC waste pipe and brass chromium plated waste coupling complete all as specified and directed by Engr-in- Charge..

S&F PVC valve less syphonic action type, flushing cistern 10 ltrs capacity,low level white with inlet, ball valve float and handle including brackets including 32mm dia PVC flush pipe for low level cistern including all joints fixed in repair complete all as specified and directed by Engr-in- Charge.

S&F in repairs 15 mm bore pillar taps fancy type (long neck) cast copper alloy with capstan heads chromium plated screwed down high pressure with or without letter hot or cold with long screwed and shanks and fly nuts screwed for iron pipes complete all as specified and directed by Engineer in charge.

S&F PVC connection 15mm dia sizes with PTMT nuts of length 600 mm complete all as specified and directed by Engineer in charge.

S&F for bib tap 15 mm bore of fancy chromioum plated with long shank & cup , screwed down high pressure with crutch or butterfly, screwed both ends for iron pipe or for brass ferrule fixed in repair complete all as specified and as directed by Engr-in- Charge.

S&F for 15 mm bore stop valves chromium plated fancy type screwed down high pressure with crutch or batterfly handle screwed both ends for iron pipes or for union fixed in repair complete all as specified and as directed by Engr-in- Charge..

Demolition or breaking up drain pipe ( salt glazed ware, AC, CI, PVC or reinforcement concrete) of any dia etc complete all as specified and directed by Engineer in charge.

S & F PVC (SWR) pipes 110mm dia in any length with rubber ring joints fixed to walls/trenches/floors etc complete all as specified and directed by Engineer in charge.

S & F PVC (SWR) pipes 75mm dia in any length with rubber ring joints fixed to walls complete all as specified and directed by Engineer in charge.

S & F PVC (SWR) bend 110mm dia with access door bends complete all as specified and directed by Engineer in charge.

S & F PVC (SWR) bend 75mm dia with access door bends complete all as specified and directed by Engineer in charge.

S&F PVC (SWR) branch piece double, (Single Y) equal or unequal 110mm Dia with access door bends complete all as specified and directed by Engineer in charge.

S&F PVC (SWR) branch piece double, (Single Y) equal or unequal 75mm Dia with access door bends complete all as specified and directed by Engineer in charge.

M&L for 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed by Engineer in charge.

S&F PVC (SWR) vent cowl of 110mm bore complete all as specified and directed by Engineer in charge.

S&F PVC (SWR) vent cowl of 75mm bore complete all as specified and directed by Engineer in charge.

Removing demolished material to a distance exc.1.50 KM but not exceeding 5KM and depositing where directed at level not exceeding 1.5 mtr above the starting point etc complete all as specified and directed by Engineer in charge.

M&L for roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust & brushing neat cement slurry with 3 kgs of cement per sqm etc complete all as specified and directed by Engr-in- Charge.

Repairs to aluminium window shutters of any description, including easing & adjusting without taking down area exc 1 Sqm but not exc 2 Sqm complete all as specified and as directed by Engr-in- Charge.

M&L for 40mm thick PCC 1:2:4 type BO using 12.5mm graded crushed stone aggregate as in levelling course to finished even and smooth with using extra cement complete all as specified and directed by Engr-in- Charge.

M&L for 10mm thick rendering in CM 1:3 on concrete surfaces of roof top and chajjas finishing the surface even and smooth without using extra cement complete all as specified and directed by Engr-in- Charge.

M&L for water proofing treatment with APP based polymeric membrane over 15mm thick plaster on roof with the following courses of treatment :- (a) Complete removal of existing treatment, cleaning & washing the concrete /tiles surface by using wire brush including junction of parapet etc. (b) M&L 15mm thick cement plaster in CM 1:4 using water proofing liquid as per manufacturer instructions over neat cement slurry @ 3kg/Sqm on roof surface. Note: Water proofing liquid /compound will be measured & paid separately. (c) Applying bituminous primer (IS 3384) @ 0.160 Kg per sqm of the surface area including cleaning the surfaces complete all as specified. (d) M&L for APP based polymeric membrane minimum weighing 3 kg/Sqm and minimum 3mm thick reinforcement with polyster non woven fabric (wt reinforcement not less than 150gms/sqm) laid in primed surfaced application including preparation and applying two coats of Heat resisting Aluminium paint over APP membrane complete all as specified and directed.

Disconnecting existing tanks size exc 1000ltr and not exc 2000ltr setting aside ( or lowering if required) for repairs, cleaning and removing all scale and dirt, etc from tanks and from mouth of circulating pipes etc and hoisting reconnecting up pipes and refixing in position, including securing access covers for tank etc complete all as specified and directed by Engr-in- Charge.

Supply and fixing 20mm dia brass / gun metal gate valve with iron wheel head screwed both ends for iron pipe including dismantling and takingout unserviceable Gun metal gate valve from existing pipe line complete all as specified and directed by Engineer in charge.

S&F in repair 20mm ball brass valves high pressure with polythene flot and flynut complete screwd for iron pipes or brass ferrule and fix complete all as specified and directed by Engineer in charge.

Taking up or down 15mm dia GI steel water tubing and connections, including cleaning and refixing the in new or old positions complete all as specified and directed by Engr -in- Charge.

S&F 15mm dia GI steel water tubing medium grade ISI marked laid in trenches or fixed to walls and ceilings or laid in floors with and including all fittings such as bends, elbows,tees, short pieces etc complete all as specified and directed by Engr -in- Charge.

-Ditto- all as per item No. 66above, but fixing only old GI tubing complete all as specified and as directed by Engineer in charge..

M&L Cutting chases, pinning in, making good to facings where required in brick walls and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelve, lintels etc and cutting chases for concealed water tubing or concealed conduct wiring etc and making good cutting n exc 10 cm girth complete all as specified and directed

Cleaning & removing all scale & dirt etc of overhead PVC tanks of 500 Ltrs capacity by taking out water at bottom by buckets by manually or vaccum cleaners as required and complete clearing of walls and bottom surface inside the reservior with wire brush, mechanically scappers and high pressure water jets. tking out soil, sand and mud settled at the bottom and finally cleaning with bleaching powder / pottassium permagnate solution. The final disinfect solution in tank need to be run through all tapping points in house, so as to disinfect the water pipe line & from mouth of circulating pipes etc complete all as specified and directed by Engr-in- Charge.

S&F rotational moulded polyethylene water storage tank tripple layer cylindrical vertical with closed top 1000 ltrs capacity hoisted and fixed in position connecting to inlet and outlet pipe connections with and including 20mm dia GI wash out with plug fixed in repairs complete all as specified and directed by Engineer in charge.

M&L for RCC M- 30 ( Design Mix) using 20mm graded aggregate as in columns,pillars, piers, posts and sturts etc complete all as specified and directed by Engr-in-Charge.

M & L for MS TMT bars 10mm dia and over as in reinforcement, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc complete all as specified and directed by Engineer in charge.

M & L for MS TMT bars 8mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders or securing with clips etc complete all as specified and directed by Engineer in charge.

M&L for form work to sides of pillars, posts, sturts, piers, columns and sanchions etc on rough finished surface complete all as specified and directed by Engr-in-Charge.

S & F rolled mild steel as in tubular trusses (framed) purlins, angle, beam, tee, channel including distance piece, cleats etc , grade Fe - 410W (gde E 250 quality B) with and including necessary cutting, bending, drilling holes, welding rebates etc complete all as specified and directed by Engineer in charge.

S & F for MS Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted,bolted or welded attachment, Fe 410-W (Gde-E-250) quality-A,etc with ornamental and intricate design complete all as specified and directed by Engineer in charge.

S&F Pre-painted galvalume aluminium zinc coated GI based corrugated steel sheeting (PPGL) 0.50mm thick of any colour having tensile strength 550 Mpa as in roof covering/cladding to wall , fixed with self tapping screws etc complete all as specified and directed by Engineer in charge.

M&L for Preparation of new steel surface of any description over 10 Cm in width or girth, not otherwise described applying two coats of synthetic enamel paints over a coat of red oxide zinc primer complete all as specified and directed by Engineer in charge.

S & F for Mild steel screw bolt machine made with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut length at bolt exceeding 5 cm but not exceeding 10 cm long, diameter of neck in exc 12 mm but n exc 20 mm,etc complete all as specified and directed by Engineer in charge.

M&L for post construction anti termite treatment of soil under existing floors using emulsion chloropyrphos treatment of soil under hole, 300 mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 ( 1 cement: 2 coarse sand) to match existing floors complete all as specified and directed by Engr-in- Charge.

M&L for providing and injecting chemical chloropyrphos emulsion ( with 20% EC) for post construction antitermite along external wall below concrete or masnory apron @ 2.25 ltr per running meter including drilling and plugging complete all as specified and directed by engr-in- Charge.

M&L for post constructio anti termite treatment at point of contact of wood work by chemical emulsion Chloropyrphos (20 EC) ( in oil or kerosene based solution) @ 0.5 Ltr / hole by drilling 6 mm dia hole at a downward angle of 45 degree at 150mm centre and sealing the same complete all as specified and directed by Engr- in- Charge.

Removal of existing concrete including loose/weak concrete from the concrete structure ie. beams/columns/deckslab etc upto beyond corroded steel reinforcements to a depth of minimum 10mm behind the reinforcement by chipping/hacking with chisel and hammer or by mechanical means like chisel hammer, pneumatic chippers including high pressure water jetting and removal of debris. Concrete around corroded reinforcement shall be removed properly. The edges of the repair locations of concrete should be saw cut to depth of at least 10mm to avoid featheredging and to provide a square edge including steel frame height of single scaffolding Complete all as specified and directed by Engr-in- Charge

Removal of existing concrete including loose/weak concrete from the concrete structure ie. beams/columns/deckslab etc upto beyond corroded steel reinforcements to a depth of minimum 10mm behind the reinforcement by chipping/hacking with chisel and hammer or by mechanical means like chisel hammer, pneumatic chippers including high pressure water jetting and removal of debris. Concrete around corroded reinforcement shall be removed properly. The edges of the repair locations of concrete should be saw cut to depth of at least 10mm to avoid featheredging and to provide a square edge including steel frame double scaffolding Complete all as specified and directed by Engr-in- Charge

Preparation of surface and removal of rust in the loosely bonded concrete of the RCC deckslab, beam / girder shall be chipped out using the mechanical cutter exposing the bars and applying Rust Remover using small brush and allow to react it for 16-24 hrs. Before applying protective coating, the surface should be wire brushed and thoroughly cleaned for dust with dry cloth including necessary scaffolding complete all as per manufacturer instructions and directed by Engr- in- Charge.

M&L for applying two coats of Anti-Corrosive Primer two component (epoxy anticorrosive zinc rich coating) on reinforcement steel surfaces uniformely. Coating shall be applied by the brush to the exposed and cleaned rebars with an interval of 45 minutes to 1 hour @40 microns DFT/ coat and allowed to completely dry for 24 hours including necessary scaffolding complete all as per manufacturer instructions and directed by Engr- in-Charge.

M&L preparation of concrete surfaces by removing loose concrete dust, dirt etc. Cleaning the surface properly and applying one liberal coat of epoxy bonding agent ( two component agent) by brush application to parent concrete including necessary scaffolding complete all as per manufacturer instruction and directed by Engr-in- Charge.

M&L 50mm thick ( average thickness) polymer modified single component alkaline resistant fibre reinforced, thixotropic, cementitious patch repair mortar on conrete structure. Applying the mortar arround the reinforcement and finishing to bring it in line with existing concrete surface including necessary scaffolding complete all as per manufacturer instructions and directed by the Engr-in- Charge. Cured mortar should exhibit compressive strength of 20 MPa after 1 day and atleast 45 MPa after 28 days, tensile strength atleast 2.5 MPa after 28 days and flexural strength atleast 7 MPa after 28 days.

M&L for micro concrete to existing concrete structure including proper tight leak proof shuttering SPL polimer modified cementitious ,low pemeable 'free flow ' non shrink ' self compacting micro concrete shall be grade M70 as per recommended w/c ratio and pouring as per the required thickness complete all as per manufacturer instructions and directed by Engr-in- Charge. Quoted rates to include scffolding costs.

Dismatling of 75 mm internal cast iron drain pipe bend single Y socket pipes jointed in cement mortar complete all as specified and directed by Engr-in- Charge.

S&F PVC (SWR) WC connector with lip ring complete all as specified and directed by Engr-in- Charge.

S&F Grating down125mm dia with waste hole of PTMT ( minimum weight 40 gms) complete all as specified and directed by Engr - in- Charge.

S&F Grating down 100mm dia with waste hole of PTMT ( minimum weight 25 gms) complete all as specified and directed by Engr - in- Charge.

Taking down unservicable/partly unservicable light fittings of any type, tube light fitting and fixtures, etc, and making good to the disturbed surfaces of walls/floor etc to macth with existing surfaces including white washing/colour washing/distempering to match with existing wall/floor/ceiling finishes complete all as specified and directed by Engr- in- Charge.

Taking down cearfully by unscrewing the unserviceable DB Boxes, MC distribution boards SP & TPN with porcelain cutouts etc and making good disturbed surfaces for wall, floors etc complete all as specified and as directed by Engr-in- Charge.

Taking down the sub main wiring of any dia / sq mm on teak wood batten / PVC conduit GI earth wire and making good disturbed surfaces for wall, floors etc complete all as specified and as directed by Engr-in- Charge.

Material and labour for providing point wiring with two runs of 1.5 Sqmm multi stranded copper conductor FRLS PVC insulated single core 1100 volts grade & with one run of 1.5 Sqmm single core multi stranded copper conductor FRLS PVC insulated 1100 Volts grade wire for continuous earthing complete in and including PVC casing and caping with all fittings/fixture etc and open recessed type Plastic Enclosure( Plastic Switch Board ) ISI Marked (IS:14772) for housing switches / sockets of the following complete all as specified and as directed by Engr-in- Charge.

One light point controlled by one switch.

One Exhaust/Wall mounted /Ceiling point controlled by one regulator/switch

One 3 pin socket 5 A on independent board.

One 3 pin socket 5 A on same board.

One bell /buzzer point controlled by one , one way switch

Material and labour for providing point wiring with two runs of 2.5 Sqmm multi stranded copper conductor FRLS PVC insulated single core 1100 volts grade & with one run of 1.5 Sqmm single core copper stranded FRLS PVC insulated 1100 volts grade wire for continuous earthing complete in and including PVC casing and caping 25mm size with all fittings/fixture etc fixed wall and open recessed type Plastic switch board) made of robust Synthetic material Fire Proof, Anti corrosive & shock proof ISI Marked complete for housing one 15 A Switch / sockets complete all as specified and as directed by Engr-in- Charge.

M&L for sub main wiring with two runs of single core 4.0 Sq mm FRLS PVC insulated unsheathed multi stranded copper conductor 1100 V grade with colour code and one run of 2.5 Sq mm ( 22 / 0.3 mm ) single core FRLS PVC insulated unsheathed multi stranded copper conductor green colour cable as earth continuity conductor including PVC casing & caping all as directed. Note :Two runs of 4.0 Sqmm copper cable, including PVC casing & capping one run of earth wire of 2.5 Sqmm copper cable shall be measured & paid as one length.) complete all as specified and directed by Engr-in- Charge.

S &F Modular Switch piano flush type single pole one way 5 amps complete all as specified and directed by Engr-in- Charge.

S &F Modular Socket out let 2 in one, 5/3 pin 5Amp complete all as specified and directed by Engr-in- Charge.

S &F Modular Switch socket combination 5 Amps 5 pin flush type complete all as specified and directed by Engr-in- Charge.

S &F Modular Switch socket combination 5 in 1, 5 pin 5/15 Amps flush type universal complete all as specified and directed by Engr-in- Charge.

S &F Ceiling rose, surface bakelite 65x50 mm three terminal complete all as specified and directed by Engr-in- Charge.

S &F Modular Call bell AC-230 Volt single pole ding dong complete all as specified and directed by Engr-in- Charge.

S &F Modular Bell push, flush type 5 Amps. complete all as specified and directed by Engr-in- Charge.

S &F Modular Electronic fan regulator 120 Watt step type complete all as specified and directed by Engr-in- Charge.

S &F Lamp holder insulated body with back plate including LED lamp 7 watt for angle holdercomplete all as specified and directed by Engr-in- Charge.

S &F earth enclosure with 2 pin earth plug sokcet complete with MCB SP 25 amp,flush mounting type complete all as specified and directed by Engr-in- Charge.

S &F LED tube light fittings decorative ultra slim linear fixture with extruded alluminium heat srink envioromentel friendly Energy efficient ready to use pack , 20 Watt , 4 feet, surface mounting type extruded pvc, snap on installers and domestic electronic Driver ,connector block ect.with all assoceries intenallt prewired & includingconeecting up with 2 core flexible cppper conductor cable with sutable size & suitable for and mounting clamps PVC squre box 75x75mm - 2 nosetc. complete all as specified and directed by Engr-in- Charge.

Taking down and S&F LED Energy Saving & Environment friendly Street/Security light fitting 25 watt , housing made out of pressure die-cast alluminum alloy with toughned glass IP 66 protection having clamp for mounting on pole/wall working input voltage range 140- 280 volt AC 50 Hz, consisting of reflective lens, wired with appropriate driver, PF> 0.95, having over voltage protection upto 400 volts, surge protection level 7-10 kV, thermal circuit protection THD<10%, made up of long life LED chip (SMD) in modular with Ra>70 & LED efficiency >120 lumen/watt & lumanries eficacy >95 lm/watt, spread beam angle along the drive way -135 degree throw, beam angle across the drive way - 75 degree including GI brackets made out of GI pipe/FI & connecting wire 02 single core PVC copper conductor cable 1100 volt of size 1.5 sqmm complete all as specified and directed by Engr-in- Charge.

Hanging only ceiling fan 1200mm Sweep by providing fan hooks in proper manner and making connection withT 3 core copper cable including painting complete all as specified and directed by Engr-in- Charge.

Taking down ceiling fan /EXHAUST FAN of any size or make and refixing the same after repair work complete all as specified and directed by Engr-in- Charge.

Sub main wiring power/circuit using PVC insulated unsheathed, stranded copper conductor cable 2 Single core of size 4 Sq mm, earth continuity conductor of size 2.5 Sq mm to be drawn through and including PVC conduit 25 mm dia medium grade conceled in walls/roof/floors complete all as directed by Engineer in Charge. Notes:-Two wires of 4 Sq mm and one wire of 2.5 Sq mm and one run of PVC conduit shall be measured as one unit.

Sub main wiring power/circuit using PVC insulated unsheathed, stranded copper conductor cable 2 Single core of size 6 Sq mm, earth continuity conductor of size 4 Sq mm to be drawn through and including PVC conduit 25 mm dia medium grade conceled in walls/roof/floors complete all as directed by Engineer in Charge. Notes:- Two wires of 10 Sq mm and one wire of 6 Sq mm and one run of PVC conduit shall be measured as one unit.

S&F MCCB DB VERTCLE TYPE made of sheet steel, powder painted with NUTRAL bus bar 200 A, neutral link, IP-43-IK09 protection grade , 415Volts TPN with 4 way Double door complete all as specified and directed by Engr-in- Charge.

S&F MCB DB made of sheet steel , powder painted with NUTRAL bus bar 200 A, neutral link, earth bar and Din rail, 240 Volts SPN with 8 way Double door, IP-43-IK09 protection gradecomplete all as specified and directed by Engr-in- Charge.

S&F MCB SPN 240 Volts, 'C' series, breaking capacity 10 KA of rating 6-32 Amps complete all as specified and directed by Engr-in- Charge.

S&F MCB SP 6-32 Amps 'C' series, breaking capacity 10 KA of rating complete all as specified and directed by Engr-in- Charge.

S&F MCCB 63 Amps, 415Volts, 25KA, 4 pole with sheet metal enclosure of size 30cmx45cm complete all as specified and directed by Engr-in- Charge.

Earthing complete with galvanised iron earth plate electrode 600 mm x 600 mm x 6mm as earthing lead buried directly in ground vertically to a depth not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 Mtr below normal ground level connected to and including galvanised earth lead 25X4 mm dia by means of bolts, nuts, check nuts & washers complete up to and including test point made out of 40x6 mm alum flat connected to DBs all as shown in electrical plate No.5 of SSR Part I of 2009 & as specified or indicated and testing on completion including excavation / earth work in any type of strata, PCC ( 1:3:6 ) type C1 earthing chamber, pre cast slab cover 50 mm thick in cement concrete ( 1: 2 : 4 ) type B 1 ( reinforced with welded steel wire fabric (XPM) weight not less than 4 Kg / Sqm), funnel with wire mesh, watering pipe of 20 mm bore medium grade,including GI strip 25x4 mm dia with GI protection pipe of 15 mm medium grade up to 7.5 meter length etccomplete all as specified and directed by Engr-in-Charge. Note:- (i) Venders are bound to get earthing result upto 5 Ohm for single earthings and 3 Ohm with the grid of two earthing.Any additional work and material required to achive the required result is included in the cost deemed to be quoted rate by Contractor. (ii) Excavated material to be removed from the site and deposit at the distance not exceeding 50m distance and levelled. (iii) On testing after completion if the desired earth resistance is not obtained the earthing will be redone at no extra cost.

Supply and fix water storage heater (Geyser) of 25 ltr capacity including complete fixing arrangement complete all as specified and directed by Engr-in- Charge.

Supply and fix exhaust fan 300 mm sweep including making hole and fixing arrangement complete all as specified and directed by Engr-in- Charge.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 4 core complete all as specified and directed by Engr-in- Charge.

MUKESH CONSTRUCTION CO

Unity Enterprises

Nilesh Construction

Safe Construction Co.

JAI CONSTRUCTION CO.