REPAIR TO SEWAGE DRAINAGE AND ALLIED WORKS BOUNDARY WALL FENCING, RETANINING WALL PATH HARDSTANDING ETC AT ASC RPA ANIMAL COY RANGPUR VIHAR BOGRA VIHAR UMRAO SINGH ENCLAVE AND OTHER NEARBY LOCATIONS AT SHIVMANDIR AREA AND STREET SECURI

Amount

Cleaning of blocked sewage line of 100 mm bore pipe by rodding from one manhole to next manhole and washing through in fresh water including removing all sludge from the sewage lines and disposing off properly outside the defence land complete all as specified and as directed.

All as per Sl item No 1 above but 150 mm bore.

All as per Sl item No 1 above but 200 mm bore.

Cleaning of gully trap / Nahani trap / water closet / wash hand basin at any floor level by rodding / rubber cap 125 mm dia and clearing blockage including removing the debris complete all as specified and as directed.

Cleaning of manhole of size not less than 0.6 m x 0.6 m & depth not exc. 1 m including lifting up & removing sludge, accumulated solid / semi solid sludge and any other foreign material with proper equipments and washing down completely with water for smooth functioning of sewage line, removing sludge obtained from cleaning to a distance not exceeding 150 m, fillling the sludge in newly excavated pit, treating with bleaching powder and refilling top of pit with earth & removing balance earth to a distance n exc 50 m complete all as specified and as directed. Note:- Rate quoted shall deemed to be included cost of all excavation & earth work.

All as per Sl item No. 5 above but depth exc 1 m & not exc. 1.5 m

All as per Sl item No. 5 above but depth exc 1.5 m & not exc. 2 m

Cleaning of septic tanks of 500 users capacity complete by bailing out water, removing sludge / dust mud and other accumulated solids, semi solids, other materials & dispossed off the same out side the defence land and including cleaning of tank with water, bleaching powder etc. complete all as specified and directed.

All as per Sl item No 8 above but 350 users capacity

All as per Sl item No 8 above but 250 users capacity

All as per Sl item No 8 above but 150 users capacity

M&L precast RCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) in landing, cover slabs (for manholes etc), chullah hoods, chajja, water troughs, mangers, shelves and similar articles with plain faces and set in cement mortar 1:4 including necessary forms, moulds etc. & demoliton complete all as specified and as directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and directed.

M&L brick work with sub class 'B' brick in old size bricks, straight or curved on plan exc. 6 m mean radius built in CM 1:6 complete all as specified and directed.

All as per SI item No.14 above but except bricks. Note :- Serviceable quantity of bricks obtained from demolition shall be reused under this item

M&L for Brick work with sub-class `B' bricks, straight or curved on plan to any radius in half brick thick wall / drain built in cement mortar 1:4 complete all as specified and directed.

M&L brick work with sub class 'B' brick, in half brick thick honey comb walling, built in CM 1:4 complete all as specified and directed.

Taking down cement plaster on brick or concrete surfaces / ceiling, racking out joints hacking for key scrubbing down with water etc complete all as specified and directed.

M&L 15 mm thick rendering in CM 1:4 on fair faces of brick work or concrete surface using water proofing compound as per manufacturers instructions finished even and smooth without using extra cement complete all as specified and directed. Note:- WPC shall be measured and paid separately.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc. 15 cm thick (Below or above ground level) complete all as specified and directed.

M&L PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in copings, bed plates, bed block for holdfasts, filling in pressed steel door frames, benching, kerbs, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating and including necessary formwork complete all as specified and directed.

M&L PCC 1:2:4 type B1, (using 20 mm graded crushed stone aggregate) as in lintels upto 1.5 m clear span, cills, steps ; seismic and other similar bands, plinth courses, coping bed plates and the like including weathering slightly rounded or chamfered angles and throating including necessary formwork complete all as specified and directed.

M&L PCC 1:3:6 type C1, (using 20 mm graded crushed stone aggregate) as in lintels upto 1.5 m clear span, cills, steps ; seismic and other similar bands, plinth courses, coping bed plates and the like including weathering slightly rounded or chamfered angles and throating including necessary formwork complete all as specified and directed.

M&L for Plain Cement Concrete Type B2 1:2:4 (using 40 mm graded stone aggregate) in surface channels and drains complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and directed.

M&L for Plain Cement Concrete Type D2 1:4:8 (using 40 mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and directed.

M&L PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) as in foundation, filling and mass concrete for pole foundation and finished the surface even and smooth without using extra cement including necessary formwork complete all as specified and directed.

M&L 75 mm thick, PCC 1:3:6, type C-2 (using 40 mm graded crushed stone aggregate) as in sub base, floors, paths, plinth protection, hardstanding etc and laid fair in alternate bays and in including filler joints with sealing compound grade 'A' if required finished even and smooth without using extra cement including demolition of old complete all as specified and directed.

M&L cement concrete chequered tiles 300 x 300 x 25 mm thick with grey cement with pigment, set and jointed in neat cement slurry and pointed in coloured cement to match the surfaces as in floors laid over and including 15 mm thick screed bed in CM 1:4 including dismantling of old tiles complete all as specified and directed.

M&L 60 mm thick factory made chamfered edge cement concrete paver block of M-35 Grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU Mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

M&L for rough finished flat formwork to soffits of suspended slabs such as roof slabs, floor slabs and similar work not exc. 200 mm thick (horizontal or sloping) work as rough finished surfaces of concrete complete all as specified and directed.

Use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n exc 20 cm wide for rough finished surfaces of concrete complete all as specified and directed.

M&L RCC 1:2:4 Type B1 (20 mm graded crushed stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and like and including demolition of old RCC concrete complete all as specified and as directed.

M&L for Mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

M&L for Mild TMT bars 6 mm to 8 mm dia., cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

Demolition and breaking up drain pipes AC 100 mm internal dia set in cement mortar complete all as specified nad directed.

All as per Sl item No 36.00 above but 150 mm bore.

All as per Sl item No 36.00 above but 200 mm bore.

M & L 100 mm dia Salt Glazed stone ware drain pipes laid in trenches and jointed in CM 1:1 complete all as specified and directed.

All as per Item No. 39 above but 150 mm dia Salt Glazed stone.

All as per Item No. 39 above but 200 mm dia Salt Glazed stone.

M & L for PCC 1:4:8 type D2 (using 40 mm graded stone aggregate) in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of 100 mm bore pipe complete all as specified and directed.

All as per Sl item No 42.00 above but 150 mm bore.

All as per Sl item No 42.00 above but 200 mm bore.

M&L for cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required, bore of pipe 100 mm complete all as specified and as directed.

All as per Sl item No. 45 above but for bore of pipe 150 mm

All as per Sl item No. 45 above but for bore of pipe 200 mm

M&L Desilting of drains and culverts in any condition (including foul conditions) with necessary dewatering and temporary diversion of drain water as required complete and depositing silt at low level area complete all as specified and as directed.

Excavation in trenches not exc. 1.50 m wide and not exc. 1.50 m in depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exc. 10 Sqm on plan and getting out all excavated material in soft / loose soil complete all as specified and directed.

Excavation in trenches not exc. 1.50 m wide and exc. 1.50 m in depth but not exc. 3.00 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exc. 10 Sqm on plan and not exceeding 1.5 m in depth getting out in soft / loose soil complete all as specified and directed.

Excavating post holes or similar holes, each not exceeding 0.5 Cum, getting out in Soft/ Loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance n exc 50 m and making good surface complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick with soils complete all as specified and directed.

Removing Excavated soils not exc. 50 m and depositing where directed at a level not exc. 1.5 m above the starting point complete all as specified and directed.

S&F in repairs vitreous china squatting pan, "Orissa pattern" white, size 580 x 440 mm with integral foot rest, 'P' or 'S' trap and excluding connection to trap and to flushing pipe, CI anti -syphonage pipe complete all as specified and directed.

S&F in repairs vitreous china european water closet pan (pedestal pattern) white in colour with fixing bolts and flush pipe, connection to trap and to flushing cistern and all joints, including plastic water closet seat cover white, closed pattern with flat bottom and cover and mild steel CP hinges complete all as specified and directed.

S&F in repairs PVC low level flushing cistern of 10 litres capacity, valve less, syphonic action type, white body, with inlet ball valve, float and handle including brackets complete all as specified and directed.

S&F in repairs vitreous china urinal half stall type, of size not less than 375 x 390 x 590 mm, white including chromium plated urinal spreader & waste coupling complete all as specified and directed.

S&F in repairs waste fitting 32 mm bore, brass, chromium plated for basins etc with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

S&F in repairs PVC connections 15 mm size with PTMT nuts, of length 450 mm & suitable for cold/hot water supply complete all as specified and directed.

S&F in repairs 32 mm bore brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing union and cap and fixed complete all as specified directed.

All as per Sl item No. 60 above but 40 mm bore.

S & F in repairs 125 / 110 mm size PVC (SWR) gully trap, setting and jointing with solvent cement including top cover grating complete all as specified and directed.

S & F in repairs 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F in repairs 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F in repairs 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S & F in repairs 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S & F 75 mm bore PVC (SWR) bends of any radius, fixed with cement solvent, with oval access door complete all as specified and directed.

S & F 110 mm bore PVC (SWR) bends of any radius, fixed with cement solvent, with oval access door complete all as specified and directed.

S & F 75 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S & F 110 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S&F 110 mm bore PVC (SWR) vent cowl complete all as specified and directed.

S & F 75 mm bore PVC (SWR) junction single, (single T) equal or unequal, complete all as specified and directed.

S & F 110 mm bore PVC (SWR) junction single, (single T) equal or unequal, complete all as specified and directed.

S&F in repairs 75 mm bore PVC (SWR) floor trap, plain with grating and including jointing with solvent cement complete all as specified and directed.

Dismantling post or struts (wood, steel or RCC) any section, embedded in concrete, brick work, masonry etc, including taking out embedded portion in concrete, masonary etc and making good the disturbed ground complete all as specified and directed.

S & F Mild steel work in Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc.wind ties, including securing bolts and posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

M&L for Plain cement concrete 1:3:6 type D-2 (using 40 mm graded aggregate) as in foundation filling for post holes and mass concrete complete all as specified and directed.

S&F in repairs galvanised. 2 strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc, (each line wire to be measured) and including dismantling the barbed wire complete all as as specified and directed

M&L mild steel round bars 10 mm dia and over, cut to length, bent to shape required, including hooking ends for securing chain link fencing, conforming to IS Fe 410-W (Gde.E-250), quality-A, complete all as specified and directed.

Supply only chain link MS galvanized fencing, of any size or type complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type of standards, rails, straining bolts, etc, and including provision of binding wire including taking down complete all as specified and directed.

M&L preparation of new steel surfaces of any description, not otherwise described over 10 cm width or girth and including applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L preparation of new steel surfaces of any description not exceeding 10 cm width or girth when unconnected with other painting or when painted in a different tint and including applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F Mild steel screw bolts diameter of neck 11 to 15 mm (machine made) with hexoganal or square heads at one end and screwed the other or screwed both ends each screwed end to be fitted with washers and one hexagonal or square nut, exc. 0.5 cm but not exc. 10 cm long complete all as specified and directed.

M&L for sand cushioning to under ground cable using locally available fine clean dry river sand over,under ground UG cable laid in treches and gently punning to cushioning to cable complete all as directed by Engineer-in-Charge. Note : For the purpose of payment only punned thickness will be measured.

M&L for common burnt clay building bricks (locally available best quality), sub-class ‘B’ designation 75 of size 230x115x75 mm to cover LT underground cables , laid dry and flat abutting each other with gaps not exceeding 10mm complete all as specified and directed.

Boring / Drilling (horizontally) manually under min 0.5 to 2 m deep in soil below existing road suitable for passing GI tubing of 40 to 80 mm bore complete all as specified and directed.

Supply and fixing of GI tubing light grade 40mm dia for protection of cable on pole , under road crossing or across drain , along electric pole or floor / wall including taking down old unsv complete all as specified and directed.

Supply, laying testing and commissoning in replacement of cable XLPE insulated screened PVC bedded galvanised steel strip or wire armoured electric power cables (heavy duty) LT Cable with stranded aluminium conductor 1100 volts grade of size 10 sqmm 4 core including taking down old unsv complete all as specified and directed.

Supply, laying testing and commissoning in replacement of cable XLPE insulated screened PVC bedded galvanised steel strip or wire armoured electric power cables (heavy duty) LT Cable with stranded aluminium conductor 1100 volts grade of size 16 sqmm 4 core including taking down old unsv complete all as specified and directed.

Supply and fixing in repairs of LED street light luminiarie 45 Watt (System Lumen output should not be less than 5400 Lumen) Energy and environmental friendly long life made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having IP-66 protection and impact resistant of IK07 with 10 KV Built-in surge protection device with high performance LEDs, System Lumen efficacy - >120Lm/Watt, power factor>=0.95, polyester powder coated with toughened glass having IP-66 protection, tempered protective polycarbonate diffuser, integrated high efficiency electronic driver with lower THD, Colour Temp (CCT)-6500K operating range. 140 to 270V, 50 Hz fixed with suitable fixing arrangement complete including LEDs with certification LM 79 for luiminare, LM 80 for LED source including all necesasary internally pre-wired and connecting up incl taking down old unsv fittings from bracket of pole with repair/replacement warranty of 5 years of OEM complete all as per locking arrangement in both front and rear door with 4 side compelet all as specified and directed by Engr-in-charge.

All as per item No. 91.00 above but of capacity 60W (System lumen output not be less than 7200 Lumen)

All as per item No. 91.00 above but of capacity 90W (System lumen output not be less than 10800 Lumen)

All as per item No. 91.00 above but of capacity 120W (System lumen output not be less than 14400 Lumen)

M&L for Weather proof flat three core PVC insulated and PVC sheathed industrial round 3 core flexible copper cable of size 2.5 Sqmm 1100 volts grade for connection of lights to Pole Box, after dismantling old one complete as specified and directed.

M&L for PVC conduit 20mm dia fixing to pole from JB to security light complete incl fixing arrangement to pole with the help of 03 pairs of clamps and nut bolts including taking down old unsv complete all as specified and directed.

S & F of Pole mounted Junction box with terminals of size 155x210x92 mm, made of high quality thermoplastic polycarbonate, dust & jet water proof, chemical, acid corrision, impact IK-09, insulated & shock proof IP 66, black color with internaly embedded gasket (PUR) , along with cover and metric knockout all sides including back of the base must including terminals 4Nos including fixing arrangement with MS flat of size 40X4mm , nuts , bolt and washers and MCB SP 6-32 Amps 01 No including taking down old unsv complete all as specified and as directed.

S&F in replacement for 32 mm dia GI tubing light grade bracket over all 1.2 mtr length bent to shape 120 degree with cutting as required and bend to shape with flat iron clamp of size 32x6 mm, 2 Nos, suitable size of nut bolts and washers complete for fixing street light fittings on electric poles/bldgs for security complete all as specified and directed.

S&F of 6 KW three phase automatic street light control panel with and including astronomical switch for automatic operation on/ off street light as per set time through programmable 24 hrs switch , 32 A TP Power contactor, 40 A TPN MCB wall /floor moutable, IP 54 enclosure made out of CRCA sheet duly powder coated conforming to IS/IEC 61439 & 60529 in built short circuit protection ,Class H insulation,FRLS internal wiring,extended wide band coil and locking arrangement with padlock and panel lock including taking down old unsv complete all as specified and directed.

Supply and fixing of energy saving LED flood light 150 watt 230 V AC outdoor type, thermal management in multiple optics and equipped with IP66 protection, energy saving, environment frriendly, long life with impact and corrosion resistant,die cast aluminium housing ,lumen efficacy of minimum 120 Lm/W,min surge protection of 10 kV incl taking down old unsv complete all as specified and as directed. Make :- Havells JETA LEGANZA/SURYA/BENLO/CG/PHILIPS or equivalent

Supply and fixing of energy saving LED flood light 200 watt 230 V AC outdoor type, thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant,die cast aluminium housing ,lumen efficacy of minimum 120 Lm/W,min surge protection of 10 kV including taking down old unsv complete all as specified and as directed.Make:- Havells JETA LEGANZA/SURYA/BENLO/CG/PHILIPS or equivalent

Supply and fixing LED post top lantern 40W ,230 volts white in color, AC outdoor type,pressure die cast aluminium body and opal PC cover with IP 66 protection and IK07 rating with minimum efficacy of 120lm/W energy saving, environmental friendly, long life asethetically designed with symmetrical light distribution, spun aluminium landscape luminaries with high power LEDs as light source. Clear cover offers bright illumination including taking down old unsv complete all as specified and as directed. Make :- Crompton Cat Part No CHAPLET or its equivalent in Bajaj /Havells /Surya

Dismantling of steel pole/struts any size embedded in concrete including demolition of concrete, etc and removing unserviceable materials from site of work complete all as directed by Engr-in-charge.

Supply and fixing 9 Mtr Long Hot Dip Galvanised Street Light Octagonal Pole with Foundation type Base Plate and Foundation Bolts and additional structural steel as reqd, dimentions of Pole as Top Diameter not less than 70 mm, Bottom Diameter not less than 130 mm, Section Length not less than 9000 mm, Thickness not less than - 3 mm, Foundation type Base Plate size not less than 200x200x16 mm , Foundation Bolts - 4 Nos not less than 20 mm dia, pitch circle dia not less than 200 mm, bolt length appox 600 mm, projects bolt length appox 100 mm , with Double type arm bracket not less than 1500 mm long each arm , top dia not less than 70 mm , suitable for LED Street Light fitting. The Pole shaft shall have octagonal cross section and continuously tapered with single longitudinal welding all including dismantling and takign down of old unsv complete all as specified and as directed. (Excavation and PCC will be measured and paid seprately)

Supply and fixing 9 Mtr Long Hot Dip Galvanised Street Light Octagonal Pole with Foundation type Base Plate and Foundation Bolts and additional structural steel as reqd, dimentions of Pole as Top Diameter not less than 70 mm, Bottom Diameter not less than 155 mm, Section Length not less than 9000 mm, Thickness not less than - 3 mm, Foundation type Base Plate size not less than 250 x 250 x 16 mm , Foundation Bolts - 4 Nos not less than 24 mm dia, pitch circle dia not less than 250 mm, bolt length appox 750 mm, projects bolt length appox 125 mm , with Single type arm bracket not less than 1500 mm long each arm , top dia not less than 70 mm , suitable for LED Street Light fitting. The Pole shaft shall have octagonal cross section and continuously tapered with single longitudinal welding all all including dismantling and takign down of old unsv complete all as specified and as directed. (Excavation and PCC will be measured and paid seprately)

S&F in repair all in one solar street light made with high efficiency IP 65 LED Solar Lightning with built-in high efficiency Solar Panel, LED Light and long life Lithium Ferro Phosphate battery with in buit BMS technology,high eficiency LED,MPPT solar charge controller and aluminium extrusion frame body & specially programmed to automatically control the dimming and brightness of light,which increases the backup time with system wattage 36W,12.8 volt,18AH battery DC system,lumen output greater than 125 lm/W,system panel module capacity 12V,MPPT charge controller & PR sensor with CCT 6000-6500K incl polycrystaline cell,IP-65 with efficiency greater than 90% with adjustable tilt angle 0-15 degree including galvanized steel pole inbuilt including takign down of old unsv one complete all as specified and as directed.Note:- Excavation and earth work will be measured and paid seprately.Make:- Surya/Orient/Havells/Crompton or equivalent

Materials and labour for Earthing complete with MS galvanized earth Plate electrode 600 mm x 600 mm x 6 mm thick, burried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 m below ground level connetced with 32x6 mm galvanized iron strip by means of nuts, bolts, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe 40 mm bore (medium grade) and other end connected to earthing test point including providing funnel and watering pipe 20mm bore galvanised iron pipe (medium grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C bothways and suitable handle made of 10mm dia) including necessary earth work, excavation, returning filling and removal of surplus earth upto a distance not exceeding 50 m etc all as shown on electrical plate No. 3 of MES Schedule Part-I(2009) complete including test point and testing including taking down of old unsv one complete all as specified and directed.

Disconnecting and taking down existing LED street light fittings of any make or any capacity for repair/replacement of burnt/worn out driver through ladder/motorized/mannual system from GI bracket on pole of any size and refix the same after cleaning,general overhauling, repairing and making serviceable to its original position and testing complete all as specified and as directed > Note :- The new consume item will be measured and paid seperately.

Supply only LED Driver of capacity 45W, BIS approved silicon gel filled potted driver for vibration proof, 10 KV surge protection device complete all as specified and directed.

All as per Sl. item No. 109.00 above but for 60W complete all as specified and directed.

All as per Sl. item No. 109.00 above but for 90W complete all as specified and directed.

M&L for painting steel tubular poles 9 mtr height with one coat of aluminium paint from bottom to top including cross arms, GI brackets etc after cleaning and preparing the surface and marking alternate white and black strips 30 cm height total 5 Nos with two coats of synthetic enamel point over a coat of primer complete including marking of pole number on pole in clear words complete all as specified and as directed.

M&L for painting of PCC poles 9 mtr height with one coat of aluminium paint from bottom to top including cross arms,GI brackets etc after cleaning and preparing the surface and marking alternate white and black strips 30 cm height total 5 Nos with two coats of synthetic enamel point over a coat of primer complete including marking of pole number on pole in clear words complete all as specified and as directed.

DEBABROTA ROY CHOWDHURY (BID ID -3485744)

MS ORIENT ENGINEERING WORKS (BID ID -3485480)

M/S A C PAUL (BID ID -3485580)

M/s TRIMURTI ASSOCIATE (BID ID -3485330)

Janata Enterprises (BID ID -3485640)

DAS AND GHOSH CONSTRUCTION (BID ID -3485573)

M/S RANEN PAL (BID ID -3485664)

ELECTRO WIR WAY (BID ID -3484928)