PROVN OF CERTAIN BR EM WORKS SERVICES AT CAC CF AND

Amount

Excavating in post holes (or similar holes) in soft / loose soil each not exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance not exc 50m and making good surface, work in hard/dense soil complete all as specified

M & L for PCC 1:3:6 Type C2 using 40mm graded aggregate as in foundations, filling and mass concrete complete all as specified and as directed by the Engineer-in-Charge.

M & L cutting holes into or through or brick walls built in cement morotr area exc 150Sqcm and N exc 400 sqcm depth upto 10 cm complete all as specified and as directed by the Engineer-in-Charge.

M & L for PCC 1:2:4 Type B 1 using 40mm graded aggregate as in foundations, filling and mass concrete complete all as specified and as directed by the Engineer-in-Charge.

Dismantling of plain or corrugated plain or corrugated steel sheeting , any gauge , thickness, including nainital pattern roof covering all as specified and as directed

fixing oly Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with with screws and washers, in roofs, walls etc.

S & F for Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with with screws and washers, in roofs, walls etc.

Distmantling of wrought iron or mild steel work of any description not otherwise specially provided for all as specified and as irected

M&L steel work in tubular trusses including special shaped washers etc complete using ERW or induction butt welded tubes confroming to IS 1161 1979 grade st 240 etc complete all as specified and directed.

Erection and fixing only steel work in tubular trusses including special shaped washers etc complete using ERW or induction butt welded tubes confroming to IS 1161 1979 grade st 240 etc complete all as specified and directed.

M&L for preparation of old painted Steel surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as directed by the Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

M&L for light shade vitrified ceramic tiles (Premium quality)10 mm thick (square/ rectagular) polished,area of each tiles not exceeding 0.36 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade tiles including 15mm thick screed bed layer in CM (1:6) complete all as specified and directed.

M&L for Glazed ceramic digital coloured first class tiles(Premium quality) in vertical surface 300x600x7 to 10mm / 300x450x 7 to 10mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade tile including 10mm thick rendering in CM (1:4) complete all as specified and directed.

M&L for Non Skid ceramic coloured first class tiles tiles 7 to 8 mm thick square / rectangular ) area of each tiles not exceeding 0.11 Sqm as in floors laid over and including 15 mm thick screed bed in CM(1:6)and pointed in white or coloured cement to match the shade tile complete all as specified and directed.

Dismantling of stone slab of any description on thickness in floor aprons etc in laid bedded and pointed in any mortar.

M&L for 18- 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, around door frame and like, jointed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.

Dismantling of boarding , any description , fixed in any position with nails all as directed by Engr _ in Charge

M&L for Providing and fixing in repair false ceiling of 16 mm thick fine fissurred RH-99 prime Make-Armstrong Tegular and accoustic purpose of size 600x600x16mm thick fixed in GI grid powder coated snap grid ceilling of l section 25 mm x25mmx1.5mm thick and Tsection 25mm x25mm x1.mm with suspender of 10 gauge GI wire of required length, fixed with dash through fastener bolt of approved quality 04 Nos for per sqm including necessary cuting, securing and making good to disturbed surface complete all as specified and directed

Taking down chowkhats with shutters (without taking off shutters from the frame) area n exc 1.5 sqm each complete all as directed by Engineer-in-Charge.

Taking down chowkhats with shutters (without taking off shutters from the frame) area exc 1.5 sqm but n. exc 4 sqm each complete all as directed by Engineer-in-Charge.

S&F double action floor spring hydraulivcally regulated made up of minimum 1.25 mm thick alluminium alloy sheet foundation box , main body with stainless steel cover, governing pivot made of brass , other parts made of mild steel hyeavy duty and fixed in position all as specified and as directed.

S&F Rebated mortice aluminium lock verticle type size 100mm with 4 levers.

S&F for powder coated anodised aluminium frame/shutters for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified.

M&L for Anodised aluminium powder coated door shutters, aluminium section weighing 1.5 kg/m ( minimum) including all necessary fittings, joining cleats, glazing clips, rubber packing, anodised alumnium snap beading, screws and lock etc complete all as specified.

S&F for powder coating Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m ( minmum) including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.), hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified. (minimum thickness of powder coating 50 micron).

S&F 5.50 mm thick tinted glass and glazing with rubber beading for alluminium doors/ and as in windows area as required complete all as specified and directed.

S&F aluminium door closer hyudraulically regulated disignation No 3 universal type suitable for door shutter of 851 to 1000 mm in width and of weight tetween 61 to 80 Kg and fixed.

S&F aluminium handle in circular shape for pull of door shutter.

S & F 200 mm long Aluminium, anodised, barrel tower bolts of extruded section

Supply & fix in repair stainless steel decorative type drapery rod finnial, end socket etc complete all as Make of drapery rod shall be of VISTA model No. Victorian series finial SW-13 or CLASSIC . Note:- (i) Brackets shall be measured and paid seperately under respective item of this schedule. (ii) Drapery rod, finnial shall be of same makes.

S&F stainless steel/ brass chromium plated Decorative bracket fancy type double slotted suitable to receive drapery rods as catered above

Taking down existing PVC cup board all as specified and directed

S&F PVC cabinet box and shutter made out of 18 mm thick one side PVC prelaminated wood grain board and shutter will be fixed on the PVC frame with auto hinges and steel screw including fancy type stainless steel handles complete all as specified and directed. Size of cabinet not more than 90 cm wide.

S&F PVC cabinet frame of size 18mm x75mm made out of 18mm thick PVC board wood grain colour and frame shall be fixed with 50mm long steel screw inside using drilling machine and plastic fasteners Make : Rajshree or equivalent complete all as specified and directed.

Taking down cement plaster of any description on brick or stone walls etc including raking out joints, hacking out for key, scrubbing down with water etc complete all as directed.

M&L fo Rendering 15 mm thick on fair faces or brick work or concrete surfaces in cement mortar (1:4) and finished fair and even without using extra cement.

Demolition of brick work stone boulder masnary built in cement mortar including all quoins arches pillars, etc complete all as directed by Engineer –in-charge

M&L for brick work with sub class ‘B’ bricks straight or curved on plan exc 6 M mean radius built in CM (1:6) complete all as specified and directed

M&L for preparation of newly plasteredd surfaces of walls and applying two coats of OBD over a coat of primer over and including 2mm thick wall care putty all as specified and as directed

M&L for complete removal of existing treatment of old plastered surfaces of walls and applying two coats of plastic emulsion paint over a coat of primer with a thin layer of 1.5 mm thick wall care putty complete all as specified.

S&F in repair vitreous china wash down water closet pan (one piece type) ivory with PVC sheet cover & flushing cistern, flushing pipe), including making good the floor with adjacent floor finishing and making connection to flush pipe etc complete including making functional and removal rubbish/waste materials to a distance n. exc 50m, complete all as specified and directed. Make of WC : ( Jaguar , Hindware Cat No 92043 (INOX) and CERA-COMFY Cat Part No 2075 / Parry ware)

S&F in repair oval shape vitreous china wash basin under counter (Cat No CNS-705) etc complete all as specified and directed. (Make: Jaguar, Hindware/Parryware/ Cera).

S&F in repair Urinal pot long patternetc complete all as specified and directed. (Make Hindware/Parryware/ Cera).

S&F Brass CP pillar tap Basin Mixer (Cat No QQT-7011), screwed for iron pipe etc complete all as specified and directed. (Make Hindware/Jaquar).

S&F 15 mm bore Angular Stop cock fancy type CAT NO F190003) cast copper alloy of , screwed down, high pressure both ends for iron pipe or for unions and fixed complete all as specified and directed. (Make Hindware/Jaquar).

S&F CP 15 mm dia bib tap cast copper alloy with fancy (CAT NO F190002) screwed for iron pipe complete all as specified and directed. (Make Hindware/Jaquar).

S&F CP push cock for urinal 15 mm dia cast copper alloy with fancy screwed for iron pipe complete all as specified and directed. (Make Hindware/Jaquar).

S&F in repair stainless steel swial towel holder twin type Cat No ACN 111SS all as specified and directed.

S&F in repair toilet paper holder with stainless steel flap Cat No ACN 1153S all as specified and directed.

S&F in repair corner glass shelf with bracket Cat No ACN1173 etc complete all as specified and directed.

S&F in repair Health faucet ABS SS Braided Hose 1 m with CP hook Cat No F160068/F160068IV etc complete all as specified. (Make Hindware/Jaquar).

S&F in repair CP connection 600 mm long braded hose with MIOXI nipple, 15 mm nut , O ring and rubber washer for 15 mm bore of pipe all as specified and directed.

S&F in repair looking mirror of 5mm thick glass including hanging arrangements and provision to receive LED back lights to give glow and decent look from out side complete.( LED lights measured and paid seperately in E/M schedule)

Taking up or down 15 mm bore steel water tubing and connections and all as specified.

Taking up or down 20 mm bore steel water tubing and connections and all as specified.

S&F 15mm bore galvanised steel water tubing medium grade, with all fitting fixed to walls, laid in floors/ceiling including concealed etc all as specified and directed.

S&F 20mm bore galvanised steel water tubing medium grade, with all fitting fixed to walls, laid in floors/ceiling including concealed etc all as specified and directed.

S&F in repair CI floor trap 75 mm dia of outlet with stainless steel grating including jointing to waste pipe in run led joint complete all as specified and directed.

S&F in repair 100 mm dia cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B1(1:2:4)

S&F MoC Stainless Steel Gde-304 and Grease trap of size 900 x 900 x x 900 mm thickness 1.8 mm basket size 345 x 325 mm & trap 75 mm including all necessary connections upto first manhole, & accessories for disposing waste water to nearby drain / chamber through drain pipe etc including cutting hole in brick wall, excavation and PCC (1:3:6) work if reqd and making good to the surface complete all as specified and directed.

S&F MoC Stainless Steel Gde-304 Oil and Grease trap of size 750 x 450 x x 450 mm thickness 1.6 mm basket size 200 x 200 mm & trap 50 mm including all necessary connections upto first manhole, & accessories for disposing waste water to nearby drain / chamber through drain pipe etc including cutting hole in brick wall, excavation and PCC (1:3:6) work if reqd and making good to the surface complete all as specified and directed.

Taking down carefully aluminium batten point, wiring for light/fan/socket/bell or power point including. All fittings i.e. switch, sockets, ceiling rose, regulators, batten holders, etc. Complete and making good disturbed surfaces of wall/floor to match with the surroundings of wall/ceiling/floor etc including taking down old light fittings. Note :- (i) Contractors quoted rate of this item deemed inclusive of unscrewing of the serviceable fittings and fixture as directed and deposit in MES store yard. (ii) Quoted rate also deem to be included cost of cutting chases for taking out concealed conduit and nitch for terminal box. (iii) Decision of GE shall be final and binding in respect of serviceability of fittings/fixture. (iv) Exhaust fan and ceiling fan shall be taken down in under separate item of this schedule.

For one light/fan/bell point controlled by one switch single pole one way

All as per item No 64 here-in-before but one 3 pin 5 amp switch socket out let independent .

All as per item No 64 here inbefore but one 3 pin 5 amps socket outlet on the same board with other switch complete .

All as per item No 64 here-in-before but using 02 Nos. 4.0 sq mm size for main cable and 01 No.4.0 sq mm size as earth conductor for one 16 amp switch socket outlet on independent board.

Supply and fix switch modular flush 6A single pole one way ISI marked (One module)

Supply and fix switch modular flush type 15/16 Amp single pole one way 240 volt one module ISI marked

Supply and fix modular sockets 6 Amp 2 in 1 2/3 pin combined (Two module)

Supply and fix modular sockets 16 Amp 2 in 1 3/5 pin combined (Two module)

Supply and fix ceiling rose surface bakelite 60x25mm three terminal 240 V grade complete all as specified and directed by Engr- in Charge.

Supply and fix electronic step type fan regulator 240 volt 50 Htz 120 watt (switch/sockets type in shape) modular type

Supply and fix white cover plate with frame one module for modular switches & sockets

All as item No 74 here and before but two module

All as item No 74 here and before but three module

All as item No 74 here and before but four module

All as item No 74 here and before but six module

All as item No 74 here and before but eight module

Supply and fix metal flush box 1/2 module 1.6 mm for mounting switches & sockets

All as item No 80 here in before but three module

All as item No 80 here in before but four module

All as item 80 here in before but six module

All as item No 80 here in before but eight module

S&F LED batten luminaire surface mounted, 4 feet system wattage of 20 Watts, system lumen efficiency >90 lumen/watt, 6500k and including connecting from ceiling rose to fitting complete all as specified and directed.

S&F LED batten luminaire surface mounted 2 feet system wattage of 10/12 watts system lumen efficiency >90 lumen/watt, 6500k and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire fixed complete all as specified and directed.

Supply and fix LED 2 X 2 ft backlite surface mounted fitting 36 Watts not less than 3200lm with Metallic CRCA powder coated body complete all as specified and directed by Engr-in-charge.

M& L for sub main wiring with 2 run of single core PVC insulated and PVC Unsheathed, multistranded copper condutor of nominal area 6 sqmm FRLS, 1100 Volts grade cable drawn into and including rigid non metalic PVC Conduit of including all fittings and one run of PVC insulated and PVC unsheathed, multistranded copper conductor of nominal area 6 sqmm FRLS 1100 volts grade cable continuous earth wire of green colour code complete. Note:- (a) Two runs of 6.0 sqmm cable and one run of 6 Sqmm cable as earth lead with conduit shall be measured as one unit length for payment. (b) Quoted rate shall deem to be included cost of cutting chasses in wall for concealconduit and making good to match with existing finish.

S & F sheet metal enclosure with socket and plug top and MCB single pole and neutral enclosure with two Pin and earth plug and socket complete with one single pole MCB, 240 V, 20 Amp.

Supply & fix in repair factory made epoxy powder coated Load line Distribution Board TPN-4 ways with metal door (IP-43 protection) fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including insulated 200 Amp copper bus bar, Isolated neutral bar, standard DIN rail, Earth bar and cable ties for cable management, top and bottom removeable gland plates with knockouts and suitable for one TPN- MCCB 100 Amp as incomer and 6 to 63 Amp SP MCBs outgoing complete all as specified and conforming to IS : 8623.

Supply and fix in repair MCCB 125 Amps, FP 415 volts 16 KA 50 HZ with thermal magnetic setting complete all as specified and directed by Engineer in charge.

Supply and fix MCB DB SPN 8 way Horizontal, IP - 43 Protection double door 240 V AC 50Hz with for MCB SPN as incomer and SP MCBs as out going with tinned copper bus bar ,neutral link earth link complete complete all as specified and directed by Engineer-in-Charge.

Supply and fix in replacement MCB, SP, 6 to 32 Amp rating, 230 volt, 10 KA, 'C' series fixed in DBs catered herein before.. Make Legrand/Hager/siemense

Supply and fix MCB, single pole and neutral, 230 volts, 40 to 63 Amp rating, 'C' series fixed in DBs catered here-in-before. Make Legrand/Hager/siemense

Supply and fixing in repair Exhaust fan 300 mm sweep(steel Body) , 1250 RPM, non metallic resin body, single phase 240 volts AC 50 Hz including louvers and for fixing of Exhaust fan and copper cable 3 core of size 0.5 sqmm for connection from ceiling rose to fan complete all aspecified and directed by Engineer-in-Charge

S &F Ventilating Fan 250 mm sweep, 1250 RPM, non metallic resin body, single phase 240 volts AC 50 Hz and connecting up complete including louvers and provision of copper cable 3 core of size 0.5 sqmm size and making of hole grountig nut & bolt complete all as specified and directed by engr-in-charge

Supply and fix in replacement LED flood light fitting high way 150 watt with surge protection 4KV inbuilt in driver and minium 10 KV seperate, IP 66 having pressure die cast aluminium housing with heat resistent toughened glass individual LED lenses complete making connection with suitable in size 3 core of wire complete as as specified and directed.

Supply and fix in replacement LED flood light fitting high way 200 watt with surge protection 4KV inbuilt in driver and minium 10 KV seperate, IP 66 having pressure die cast aluminium housing with heat resistent toughened glass individual LED lenses complete making connection with suitable in size 3 core of wire complete as as specified and directed.

Supply and fix in repair wall mounted fan 400mm size, 230 volts , 50 Hz 1420 RPM with 90 degree oscillation and having speed control by pull cord system complete all as specified and directed.

M&L for Earthing complete with galvanised steel earth plate electrode 60 x 60 cm x 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised iron wire 4mm dia as earth lead wire by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in Electrical plate No. 3, MES SSR Part I- 2009 with 15 mm dia medium grade GI pipe as a protection to earthing lead and 20 mm dia medium grade GI pipe for watering purpose including excavation & earth work in any type of soil, funnel, wire mesh, RCC pit with cover, cast iron frame complete and connected to earthing test point all as specified or indicated including testing on completion. Notes (i) The concrete pit shall be PCC (1:3:6) type C-1, 40mm thick precast cover slab of RCC with suitable Mild steel handle in lieu of cast iron cover shown in electrical plate No 3 of MES SSR Part-I (ii) PCC pit shall be provide at least 500 mm away from the earth pit and not on just on the eath pit and extra cost of additional length of water pipes and fittings junction etc shall be deemed to be included in the rate. (iii) Item includes the cost of 7.5 metre earth lead wire and GI pipe for protection of earth wire. Any varriation in quantity shall be adjusted.

Supply installation commissioning and testing hi wall split units indoor and outdoor complete with cordless remote control unit with in built air ioniser and plasma filter for better indoor air quality with minimum 5 star rated, invertor type and capacity 2 ton including breaking necessary hole in wall any type for fixing indoor and outdoor unit and making good disturbed surfaces with cement mortar and paint to match existing surface, all as required including necessary connections complete all as specified and directed. Make : O Geveral / Dikin / Misibusi

Supply and fix Voltage stabilizer for automatic operation, Single phase naturally air cooled outdoor type,Built-In Thermal Overload Protection,Low & High Voltage cut-off Protection & designed for input variation between 150 V to 285 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 5 KVA ,all as required including necessary connections complete all as specified and directed

Supply and fix exhaust fan, steel body AC single Phase 230V of size 450mm sweep with, blades, and frame and louvers all as specified and directed. Make : Bajaj/CG/Havells

Cutting the existing wall/removing existing steel bar to make a hole for fixing of exhaust fan through packing of wooden ply to support the ventilating/ air circulating fan including necessary nut and bolts of suitable size incl making good of disturbed surface complete all as directed by Engr-in charge.

Supply & fix in repair factory made epoxy powder coated Load line Distribution Board TPN-4 ways with metal door (IP-43 protection) fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including insulated 200 Amp copper bus bar, Isolated neutral bar, standard DIN rail, Earth bar and cable ties for cable management, top and bottom removeable gland plates with knockouts and suitable for one TPN- MCCB 100 Amp as incomer and 6 to 63 Amp SP MCBs outgoing complete all as specified and conforming to IS : 8623.

M& L for sub main wiring with 2 run of single core PVC insulated and PVC Unsheathed, multistranded copper condutor of nominal area 4 sqmm FRLS, 1100 Volts grade cable drawn into and including rigid non metalic PVC Conduit of including all fittings and one run of PVC insulated and PVC unsheathed, multistranded copper conductor of nominal area 2.5 sqmm FRLS 1100 volts grade cable continuous earth wire of green colour code complete. Note:- (a) Two runs of 4 sqmm cable and one run of 2.5 Sqmm cable as earth lead with conduit shall be measured as one unit length for payment. (b) Quoted rate shall deem to be included cost of cutting chasses in wall for concealling conduit and making good to match with existing finish.

M& L for sub main wiring with 2 run of single core PVC insulated and PVC Unsheathed, multistranded copper condutor of nominal area 10 sqmm FRLS, 1100 Volts grade cable drawn into and including rigid non metalic PVC Conduit of including all fittings and one run of PVC insulated and PVC unsheathed, multistranded copper conductor of nominal area 6 sqmm FRLS 1100 volts grade cable continuous earth wire of green colour code complete. Note:- (a) Two runs of 10 sqmm cable and one run of 6 Sqmm cable as earth lead with conduit shall be measured as one unit length for payment. (b) Quoted rate shall deem to be included cost of cutting chasses in wall for concealling conduit and making good to match with existing finish.

Note :- Credit shown in credit schedule of tender document shall be considered by the tenderer while quoting the rates of various items of this schedule. The same shall be recovered from various payment to contractor before handing over old material.

Pleiad Complex On

M/S R S Traders

chauhan construction