Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Tender Value
Refer Docs
Closing Date
31 Aug 2022, 4:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Susen Murmu
Irugur TOP Installation, Bharat Petroleum Corporation Limited
SUBJECT: TENDER FOR SUPPLY OF COPPER CORROSION BATH APPARATUS AT IRUGUR TOP INSTALLATION UNDER CRFQ NO 1000391093 DATED ON 08.08.2022 Kindly quote you lowest rate per unit against each item in figures as well in words and your rates are valid for a period of 60days up to 30.10.2022.After successful completion of contract period ,Repeat order shall be placed on mutual agreement. The quoted amount shall inclusive of all rates, taxes and duties but excluding Goods & Service tax will be paid extra as per prevailing rates and policy /rules and regulations. Kindly note that this is an e- tender and bids have to be submitted only online. Your offer is liable to be rejected if there is any deviation from terms and conditions and special conditions of the said tender. Following five documents are uploaded as tender documents. You are requested to sign all documents digitally and upload all documents in the tender without any corrections. Please note that even if a single document is missed while digitally signing uploading; the bid is tantamount to reject. Conditional bids will also be liable for rejection .No changes shall be made in the tender documents and it should be digitally signed and uploaded as it is. Tender Documents 1. Tender Covering Letter. 2. General Conditions of Contract 3. General Purchase Contract 4. Bid Security Declaration During the technical evaluation above parameter of successful digital signing and uploading of tender documents will be checked. Your offer digitally signed on all pages of bid and attached tender documents files should be signed digitally and uploaded in the e- procurement portal of BPCL on or before 26.08.2022 @ 1600 Hrs. BPCL will not be held responsible for any delays due to connectivity issues etc. The rates should be quoted for the specifications mentioned in the tender only and no deviation will be entertained. Any deviation found in the bid; same will be liable for disqualification. You may kindly contact us if in case you need any clarifications before submitting your offer. <p class="MsoNormal" style="ma
5044
1000391093
Limited Tender
Works
Irugur TOP Installation
31 Aug 2022
9 Aug 2022
31 Aug 2022
9 Aug 2022
31 Aug 2022
9 Aug 2022
SCOPE AND TECHNICAL SPECIFICATIONS FOR TENDER FOR COPPER
A Stainless-Steel copper corrosion liquid bath of SS 304 fine finish conforming to IS 1448 P15 / ASTM
D130 having provisions of 6 test wells to accommodate Corrosion Pressure Vessels as well as test
tubes of diameter 25mm x 150 mm Test Tubes. The bath shall incorporate a center hole with a
protruding aperture on the top cover for mounting a thermometer or digital thermometer probe which
can be used to verify the oil bath temperature. The bath shall be capable of achieving a temperature
stability of better than ±0.1 °C at temperatures between 20 and 150 °C. Temperature controller shall
be with a digital display with 0.1°C resolution of Eurotherm make. A float switch interrupts power to
the bath in the event of low bath fluid level. The bath is mechanically agitated to insure test point to
test point temperature uniformity. All the bath wells shall be provided with a metallic / silicone lid and
holders for positioning the 25mm. x 150 mm Test Tubes as well as for vertically immersing the
corrosion pressure vessels as per ASTM D130 / IS 1448 P15.
The quoted price shall be inclusive of all accessories 24 months warranty, successful installation,
commissioning and listed accessories.
Detailed Technical Specifications
TEMPERATURE RANGE Ambient +5 °C to 150 °C
TEMPERATURE CONTROL ± 0.1 °C
BATH FLUID Silicone Oil (KV at 40deg C 20 cSt)
BATH CAPACITY 34 Liters
HEATER POWER ( 2NOS) 1500 W / 1000 W
WATER INLET NOZZLE 10 mm
OVERFLOW DRAIN 10 mm
VOLTAGE 220/240 V, 50 Hz with industrial metallic plug.
SIZE (HXWXD) INNER TANK Approximately 50 x 45 x 35 cm
1. The bath shall be of leak proof rugged construction with stable base. The bath shall be
made of non- transparent material (SS 304) and shall be deep enough to submerge a
minimum of 6 nos of pressure vessels and 25mm x 150 mm Test Tubes during the test.
2. Inner tank shall be made of SS 304 in 18-20 swg. Outer tank shall SS 304 with 20-24 swg.
3. Temperature controller shall be of Eurotherm make having resolution of 0.1 deg C or
lesser. PID type controller shall have both set readings as well as actual reading.
4. Minimum joints shall be ensured and all joints must be TIG welded or silver soldered and
5. The bath wells shall have suitable provisions for properly holding each pressure vessel/
the test tube (25mm x 150 mm) in a vertical position. Hook lids to hold the pressure vessel
6. The bath shall have suitable support to hold each test tube to a depth of about 100mm as
measured from the bottom of the test tube to the bath surface.
1. Stainless Steel Test Pressure Vessel For D130 Including O Ring And Leak Proof Screw
Cap shall be of the dimension mentioned in the specifications (2 nos to be provided as
SCOPE AND TECHNICAL SPECIFICATIONS FOR TENDER FOR COPPER
accessories). The pressure vessels shall be Capable of withstanding a test pressure of
700 kPa gauge as per figure-1 of IS 1448 P:15 or ISO 2160:1998
7. The bath shall have sufficient heater capacity to raise the bath temperature with ±1.0 deg
C in 15 minutes from switching on with full bath liquid.
8. Suitable type of heaters of sufficient capacities shall be provided and connected to the
Eurotherm electronic digital PID controller with Pt100 sensor to control the temperature of
the bath with in ±0.1 deg C throughout the testing duration.
9. Suitable multi blade stirrer with sufficient stem length and blade size powered by high
quality stirrer motors shall be provided to the bath to maintain uniform temperature
throughout all the bath wells. The r.p.m of the motor shall be so selected that the
circulation of the bath fluid is uniform and the motor operates at a controlled speed and
very low sound.
10. The bath shall incorporate a center hole with a protruding aperture on the top cover for
mounting a thermometer or digital thermometer probe which can be used to verify the oil
bath temperature. In addition to this another probe provision to be given at a distance of
10 cm from the centre position to keep a glass thermometer for intermittent comparison of
the temperature reading of the central probe.
11. Calibration certificate for the Eurotherm Temperature controller for the set values at
deg C and at 100 deg C shall be provided.
12. To prevent over heating in the event of primary controller failure, a high limit elelctronic
lock shall be provided to interrupt power to the bath beyond a temperature of 120 deg C.
13. All gaskets , lids, supports, insulations etc., shall with stand high test temperature as high
14. The copper strips shall be cut from smooth surfaced hard temper, cold-finished electrolytic
grade copper of more than 99.99% purity. Electrical busba stock is generally suitable.
The strips shall be 75±5 mm in length, 12.5±2 mm in width and 15 ro 3.2 mm thick in
dimensions Shall be certified from ISO 17025 laboratories for purity.
Accessories to be Provided along with the copper corrosion bath
Detailed list of Accessories
(Shall be provided along with the bath. The cost of accessories shall be included in the cost of
NAME OF ACCESSORIES QUANTITY
1 SS TEST PRESSURE VESSEL FOR D130 INCLUDING O RING AND
LEAK PROOF SCREW CAP.
2 THERMOMETER IP 64C WITH CALIBRATION CERTIFICATE
3 TEST STRIP POLISHING VISE FOR HOLDING THE COPPERSTRIP
WITHOUT MARRING THE EDGES WHILE POLISHING.
4 TEST TUBE HOLDERS /SUPPORTS 6 nos
6 PRESSURE VESSEL HOLDERS ( LIDS WITH HOOKS) 6 nos
SCOPE AND TECHNICAL SPECIFICATIONS FOR TENDER FOR COPPER
7 COPPER STIRPS WITH NABL CERTIFICATE OF PURITY THE PURITY
CERTIFICATE SHALL BE FOR THE STRIPS SUPPLIED.
8 SILCON CARBIDE POWDER, 105 MICRON (150 MESH) 500G.
9 SILICON CARBIDE PAPER 240 GRIT, A4 SIZE SHEETS
Safety Features
1. All electrical fittings shall be with fire proof wiring.
2. To prevent over heating in the event of primary controller failure, a high limit elelctronic
lock shall be provided to interrupt power to the bath beyond a temperature of 120 deg C.
3. Sufficient insulation to be provided to avoid electrical shocks and hazards.
General terms & Condition
1. The supply and installation of copper corrosion bath to done at
BPCL IRUGUR TOP INSTALLATION,
RAVATHUR P.O., IRUGUR VIA,
2. The payment will be made after successful supply & installation of subject item. The bill
should be addressed to Business Process Excellence Centre (BPEC) 4th Floor, BPCL
Office Complex Plot No. 6, Sector – 2, Behind CIDCO Garden, Kharghar, Navi Mumbai -
410 210 with a copy to us.
3. Payment will be released through NEFT directly to the Vendor's account.
4. BPCL reserves the right to modify /cancel in full or part/extend due date without assigning
any reasons at their discretion and contractors have no right seeking reasons for such
actions by BPCL.
5. BPCL reserves the right to terminate the contract (in part or full) before its expiry without
giving any reasons at their discretion and the contractor will not have any right for any
claims/damages with BPCL on account of this. Contractor is fully responsible for any
consequences/loss/liabilities/risks solely in case the contract is terminated before expiry
of the contract period. The equipment should be complete in all respect and instrument
should be ready to use. In case of the instrument being non-operational for want of spares
or accessories not mentioned in the offer, the vendor shall have to supply the same and
bring back the instrument in working condition without any charge whatsoever.
6. Party shall provide any pre-installation requirement before delivery for smooth
commissioning of the instrument.
7. Party shall install and commission the instrument within 90 days from the date of issue of
SCOPE AND TECHNICAL SPECIFICATIONS FOR TENDER FOR COPPER
8. Party shall supply, operation and maintenance manual including that of the controller.
9. Party shall provide 24 months warranty to the supplied instrument and spares from the
date of successful commissioning at BPCL site (QA laboratory, BPCL Irugur TOP Inst.,
Coimbatore ,TN)
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
RAW_HTML
5044.pdf
pdf • 2.28 MB
BUDGETDOC_5044.pdf
pdf • 0.87 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .