SPL REPAIRS OF P-398 (1,2,3,4) TYPE-I (CIV ACCN) AT NIRMAN VIHAR AREA UNDER GE (S) JAIPUR AT JAIPUR MIL STN

Amount

Taking down cement plaster from brick walls of any description, racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:6) on any face of brick walls or concrete surfaces, surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:4) on any face of brick walls or concrete surfaces, surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10 mm thick in cement mortar (1:3) on any face of ceilling of concrete surfaces, surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of newly palstered surface of wall and applying 2mm thick putty to make the entire surface free from undulations and finally applying two coats of oil bound distemper complete all as specified and directed

M&L for preparing newly plaster surface of ceiling and applying two coats of white wash complete all as speciifed and as directed.

M&L for applying 2mm thick wall care putty over ceiling on newly plastered surface complete all as speciifed and as directed

M&L for preparation of newly plastered surfaces of wall and applying two coats of exterior emulsion paint over a coat of primer including scaffolding upto three storey building complete all as specified and as directed.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and as directed.

S&F factory made PVC cup boards/ Shelf / Partition of required size consisting of panel of 18mm thick board with machine pressed laminate of desired colour complete as direction of Engineer-in-Charge.

S & F 5mm thick PVC panelling in back of cup board, one side prelam fixed with screws including all fitting arrangement fixed in repair complete all as specified and as directed.

S & F Continuous (piano) hinges,width of flaps 30mm (when open) mild steel, bright finish or electrogalvanised complete all as specified and as directed.

Supply and Fix magnetic catcher of good quality made up of plastic and sheet metal plate of suitable size for fixing in cupboard or PVC shutter complete all as specified and as directed.

S&F SS handles of 150mm in size fabricated type with bright finish in oval shape with SS Screws complete all as specified and as directed.

Taking down door chowkhat or frames with shutters (without taking out shutters ,from the frame) n exc 1.5 Sqm complete all as specified and as directed.

Taking down door chowkhat or frame exe 1.5 sqm but n exc 4 sqm with shutter (without taking off shutter from the frames) complete all as specified and as directed.

S&F 40mm thick Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type and both face is covered with decorative face veneer with lipping/frame to match complete all as specified and as directed.

S& F Factory made, 35mm thick, 2nd class hard wood, glazed and skelton shutters, open rebated and prepared to receive glass/ gauge etc but divided into squares, with plain, chamfered or rounded,mitred and rebated sash bars,(door consist 4 to 6 panels) edges of framing plain , chamfered or rounded fitted with cut and mitered beads for securing glass etc size member of shutters as specified in SSR Pt I ,section 8, clause 8.24 (a) complete all as specified and directed.

M&L Solid PVC Door Frame of size 50mm x 47mm made out of 5mm prelam PVC sheet & edges will be painted to match with prelam sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and as directed.

M&L Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded prelam PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelam PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of prelam PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and as directed.

M&L powder Coated (minimum thickness of powder coating 50 micron) Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. stainless steel screws, including making good disturbed portion with the cement mortar 1:4 or providing PCC 1:2:4 type B0 in fill of opening complete all as specified and as directed.

M&L powder coated (minimum thickness of powder coating 50 micron) aluminium window and ventilator shutters, fixed/side hung or sliding type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws complete all as specified & as directed.

S& F aluminium alloy ,anodized sliding door bolt with hasp and staple and fixing clips of sheet , cast or extruded section , and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed length of bolt 300 mm , fixed iin repairs complete all as specified and as directed.

S & F extruded aluminium anodised alloy handles, fabricated type, size of handle 150 mm, complete all as specified and as directed.

S&F aluminium ,anodized 200mm long barrel tower bolts of extruded section, complete all as specified and as directed.

S&F aluminium ,anodized 150mm long barrel tower bolts of extruded section, complete all as specified and as directed.

S&F 100mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin,anodised and fixed, type B-21 with SS screw of good quality complete all as specified and directed

S&F 300mm, ordinary rat tail rod pattern springs including roller and roller plate inclunding fixing to existing steel with welding or wooden frame complete all as specified and directed

M&L for PVC connection, 450mm long, with two sets of brass nuts & washers (one at each end) etc suitable for 15mm bore of pipe as in repairs complete all as specified and directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

Demolition of brickwork or stone/boulder masonry, including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles built in cement mortar or cement lime mortar complete all as specified and directed.

M&L for brick work in cement mortar 1:6 using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6 metre mean radius complete all as specified and directed.

M&L Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and as directed

Demolition of reinforced cement concrete as in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas, shelves, and similar suspended work and removing debris outside MD land complete all as specified and directed.

M&L for Precast cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in landings, cover slab (for manholes etc),chullah hoods, chajjas, water troughs,mangers, shelves and similar work including necessary form work and set in CM 1:4 complete all as specified and directed.

M & L TMT bars 10mm dia and over cut to length, bent to shape required incl. cranking, bending and incl. mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Demolition of cement Concrete of any description and in any position not otherwise specifically provided complete all as specified and as directed

M&L for PCC 1:3:6 type C2 using 40 mm graded stone aggregate, 75 mm thick in plinth protection laid in panels and finished even and smooth including necessary form work complete all as specified and directed. Note : Joints 12mm wide to the full depth of PCC shall be provided at every 3 meters and at every change of direction and shall be filled with mixture of bitumen and sand 1:3 by weight. Cost of this provision shall be deemed to be included in quoted rate complete all as specified and directed.

M&L for 75mm thick cement concrete (1:3:6) type C-1 using 20 mm graded stone aggregate as in sub base of floor etc complete all as specified and as directed.

Demolition of stone slab and tiles of any description or thickness laid dry or laid dry and pointed in floor, aprons or as in slabs complete all as specified and as directed.

M&L for Granite 25 mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 15mm thick screed bed/back coat in cement mortar 1:4 complete all as specified and as directed.

Rounding/moulding and polishing to edges of stone slab ( granite) two edges such as in cooking platform complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. and brushing with neat cement slurry with 3.0kg of cement per sq. metre complete all as specified and directed.

M& L for Machine cut kota stone slab flooring 20-25mm thick over 15 mm thick screed bed in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

- Ditto- all as per ser item No 44.00 above but in skirting including 10mm thick back coat in CM 1:4 complete all as specified and directed.

S&F 4.80mm thick, plain sheet glass ordinary quality and glazing, with oil putty or with wooden beads, in squares exc 0.50 Sqm in each pane complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in lintels upto 1.5 m clear span, coping, benching, bed block, lintel band, plinth courses etc and similar work including weathering,slightly rounded or chamfered angles and throating including necessary form work complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing),removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L Glazed ceramic tiles in vertical surface 350x 250x 7mm/ 450X 350X 7mm thick set and jointed with fixing adhesive complete all as specified and as directed.

M&L Non skid ceramic joint free coloured tiles 7-8 mm thick (square or rectangular)area of each tile exc 0.06 SQM but not exc 0.11 SQM in floors etc.. Set and jointed in neat cement slurry and pointed in white or coloured cement to match as in floors including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for joint free Non - skid Ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including provision of border and 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L 25 mm thick for PCC Flooring using cement concrete 1:2:4 type B-0 using 12.50 mm graded stone aggregate below floor tile as in levelling course complete all as specified and directed.

S&F Rotational moulded polye?thylene 500 litres three layered water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including dismantling old unserviceable water tanks complete all as specified and as directed.

S&F 20mm dia 3-layer PP-R Polypropylene random copolymer)concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. including taking down 15 mm dia steel tubing and connections complete all as specified and as directed.

S&F 25mm dia 3-layer PP-R Polypropylene random copolymer)concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. including taking down 20 mm dia steel tubing and connections complete all as specified and as directed.

S&F in repair 20mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

S & F in repairs 20 mm dia ball valves high pressure PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe or brass ferrule complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed

S&F for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

S&F rolled mild steel in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to Fe 410-W (Gde?E- 250) quality A?complete all as specified and as directed.

Dismantling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and as directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth in brick wall complete all as specified and directed

S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, of 110mm bore..including taking down of existing pipe complete all as specified and directed.

S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, of 75 mm bore..including taking down of existing pipe complete all as specified and directed.

S&F PVC (SWR) bend of any radius of 110mm bore including taking down of existing bend complete all as specified and directed.

S&F PVC (SWR) bend of any radius of 75mm bore with access door including taking down of existing bend complete all as specified and directed.

S&F PVC (SWR) bend provided with access door of any radius of 110mm bore complete all as specified and directed

M & L PVC (SWR) floor trap, plain with grating including jointing with solvent cement diameter of outlet 75mm bore complete all as specified and directed.

M&L for High density polyethylene pipes(HDPE) of 50mm bore of pressure rating 6 kgf/cm2 laid in trenches and connecting with floor trap including reducer if any required complete all as specified and as directed.

Excavation in trenches, n exc 1.5m wide & n exc 1.5m in depth; for foundation etc. n exc 10sq m on plan & n exc 1.5m in depth & getting out in soft/loose soil complete all as specified and as directed.

Demolition and breaking up drain pipes salt glazed ware set in CM of 150 mm dia bore pipe complete all as specified and as directed.

M&L for concrete bed to 150mm dia bore drain pipes including packing under & haunching against the sides of pipes after they are laid & tested; in PCC (1:4:8) type D2 complete all as specified and as directed.

M&L for 150mm dia bore salt-glazed stoneware drain pipes grade 'A" laid in trenches and jointed complete all as specified and as directed.

S & F in repairs PVC valve less symphonic action type flushing cistern 10 litres low level with all internal fittings including flush pipe with bend , 450mm long PVC connection and connected to WC complete all as specified and directed.

S&F in repair wash hand basin, flat back 550x400mm vitreous china (white) including PTMT waste coupling of 32mm bore size, waste pipe PVC of 32mm bore, PVC connection 450mm long with angle iron/cast iron brackets of required size as directed & making good disturbed surfaces to match with the existing complete all as specified and directed.

S & F in repairs sink with drainage board made of stainless steel 1mm thick kitchen with plug washers and waste coupling and pipe including bedding in cement mortar on to dwarf walls or cantilever brackets and connecting union to pipe overall size 915x460mm, bowl size 410x330x160 mm complete all as specified and directed.

M&L Squatting pan orrissa pattern vitreous china white of size 580mm x 440 mm with integral foot rests including necessary lime concrete and 100 mm bore sand cast cast iron ‘P’ trap with 550 to 600 mm long neck for connecting WC to branch piece with cement joints, fixed in repairs, complete all as specified and directed.

M&L in repair for 100mm dia Cast iron Nahani trap with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed.

S& F PVC (SWR) gully traps of size 125/110 mm setting and jointing with solvent cement complete all as specified and directed.

Supply & fix in repair stainless steel curtain rail fancy type 20mm dia complete all as specified and directed.

Supply & fix in repair fancy type stainless steel brackets for curtain rod with SS screws complete all as specified and directed

Supply & fix in repair fancy type SS side holder/ bulb for 20mm dia curtain rod complete all as specified and directed

S & F in repairs stop valve fancy type of 15 mm bore cast copper alloy chromium plated screwed down, high pressure, with crutch or butter fly handle long shank and cup (concealed type) screwed both ends for iron pipes or for unions complete all as specified and as directed.

S & F in repairs 15 mm dia Bib tap cast copper alloy chromium plated fancy type and screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed.

S & F in repairs cast copper alloy CP 15 mm dia pillar taps, fancy type screwed down high pressure, with or with out lettered ‘Hot’ or ‘cold’ with long screwed shanks and fly nuts complete all as specified and directed.

S&F in repairs brass 15mm bore CP Wall Mixer for mixing hot & cold water secewed down for iron pipe complete all as specified and directed.

Demolition of PCC in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L Cement concrete type D2 1:4:8 using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm tickness , M-35 grade, set, jointed over and including 25 mm thick sand cushoning complete all as specified and directed.

Dismantling posts or struts embedded in Concrete, brick work, masonry, etc.(wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground complete all as specified and directed.

S & F mild steel work as in fencing posts/ flat iron as in straps to hold chain link fencing incl. cutting tops to shape as directed , drilling holes, notching for wire etc.,flat iron fillets (for securing wire mesh etc.)incl. all necessary drilling, bolting or riveting etc. and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

Supply only chain link MS galvanised fencing any size or type or as approved complete all as specified and directed.

Fixing only Chain link fencing including line wire any mesh size and type to any type of standards, rails, straining bolts etc including provision of binding wire complete all as specified and directed.

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of nut exc 5cm but not exc10 cm long and 16 to 20 mm dia of shank complete all as specified and directed.

M&L MS round bars 10 mm dia as in chain link fence cut to length bent to shape and making hooks Fe-410-W (Gde.E-250) quality-A or Fe 290 (Gde -E-165) complete all as specified and directed

Demolition of PCC in roof covering, kerbs, roof kerbs, benching, coved fillets etc including removal of old existing roof treatement if any and removal of rubbish outside from MD land complete all as specified and as directed.

M&L for surface preparation by removal of all loose particle to ensure clean, smooth and dry surface including washing and rubbing down with water and laying 25 mm thick PCC type B-0, (1:2:4) using 12.5mm graded stone aggregate finished even & smooth without using extra cement over the existing surface of roof with WPC as per manufacturer instruction complete all as specified and as directed.

Water Proof treatment to RCC Roof comprises the following complete all as specified and as directed:- (a) Applying High build elastomeric waterproofing coating based on aliphatic polyurethane, cold applied with spray/brush applicatiion, membrane with an elongation of 350% and crack bridging abillity of 2mm as per ASTM D 412. The system including final base preparation, single coat of single component PU based primer and applying Berger HS Elastoseal or equivalent brand of make: SIKA/ ASIAN Paint/ IWL in two coats to achieve a min thickness 1.2mm etc complete all as per manufacturer specification. (b) Necessary gurantee for 5 years shall be submitted by the contractor Make : SIKA/ASIAN Paints/IWL/Berger Paints.

M & L for applying bond coat of epoxy bonding agent & cement in 1:1 ratio for bonding old and new concrete on damaged surfaces applying polymer modified mortar in CM 1:3 including mixing of polymer latex additives upto 60mm thickness (Chajjas fins, border etc) Note: (i) Qty of ploymer to be used 15% by weight of the cement or as per manufacturer instruction (ii) Use of electrical mixer to get the homogeneous dough on bond coat surfaces. (iii) To achieve required thickness repeat this step after 24 hrs as required.(iv) Keep the surfaces moist using water fog for 5 to 7 days etc complete all as specified and as directed. (v) Rate shall be inclusive of all necessary scaffolding for building height one storey complete all as specified and directed Make : - Epoxy bonding agent shall be Krishna, Dr Fixit, MC Bauchemie and M/s Cemistik, Sika or Equivalent complete all as specified and directed.

Taking down carefully surface aluminium or copper point wiring with PVC casing or conduit (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling roses, regulators, sockets, light fittings etc and making good disturbed surfaces of walls, floors, etc complete all as specified and directed

Taking down and dismantaling Ceiling fan including accessories of any type or make,safely and refixing after oiling, greasing and servicing in serviceable condition duly painted by synthetic enamel paint of in white/off white colour complete all as specified and directed including writing MES Nos. complete all as specified and directed

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 1.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green), concealed in wall, drawn into and including rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and terminated in modular metal flush boxes for mounting switches, sockets, fan regulator as required for one light point controlled by one switch complete all as specified and directed.

All as per item No. 104.00 here-in-before but one fan point controlled by one switch complete all as specified and directed

All as per item No. 104.00 here-in-before but one Exhaust fan point controlled by one switch complete all as specified and directed

All as per item No. 104.00 here-in-before but one light point controlled by two, two way switch complete all as specified and directed

All as per item No. 104.00 here-in-before but One socket outlet 6 amp controlled by one switch on indepdendent board complete all as specified and directed

All as per item No. 104.00 here-in-before but One bell point controlled by on bell push button complete all as specified and directed

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 4.0 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 4.0 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and terminated in modular metal flush boxes with modular white cover plate with frame for one socket point 16 Amps controlled by one switch on indepdendent board complete all as specified and directed

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 1.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and terminated in modular sunken boxes for mounting switches, sockets, as required One socket outlet 6 amp controlled by one switch on the same board with other switches complete all as specified and directed. Note for Item No 104.00 to 111.00 :- (a) The cost of Modular Metal flush box & modular cover plate colour and size as required at site and cutting chases in stone masonary and making good disturbed surfaces using CM 1:3 shall deemed to be included in quoted rate and the make of modular plate shall be of the same brand as per Switch/Socket accessories (b) Modular switch/socket accessories shall be measured & paid separately in respective item

S&F angle holder 6A, 240V insulated polycarbonate body with back plate complete all as specified and directed.

S&F switch modular 1 way 6/10 Amps, 230 volts, 1 module complete all as specified and directed.

S&F modular socket 6/10 Amps, 2/3pin combined 2 module AC 230 volts complete all as specified and directed.

S&F modular switch 1 way 16/20 Amps, 230 volts, 1 module complete all as specified and directed

S&F modular socket 6/16 Amps, 2/3pin combined 2 module AC 230 volts complete all as specified and directed

S&F modular fan regulator 120 watts, 2-module AC 230 Volts complete all as specified and directed

S&F switch modular 2 way 6/10 Amps, 230 volts, 1 module complete all as specified and directed

S&F Modular bell push 6A 1 module complete all as specified and directed

S&F musical bell, AC, 230 volts, single pole complete all as specified and directed

S&F ceiling rose 3 pin(phase,neutral and earth polycarbonate body complete all as specified and directed

M&L for submain wiring alongwith earth continuity conductor with PVC insulated FRLS multistranded copper cable of size 2 x 6 sqmm drawing into and including rigid non metallic PVC conduit concealed in wall, medium grade not less than 20mm dia ISI marked ivory colour with all conduit fitting and fixing accessories and 6 sqmm FRLS multistranded copper conductor cable as continuous earth wire complete all as specified and directed (Note1 :- 2 runs of 6 sqmm copper wire and 1 run of 6 sqmm copper earth wire alongwith PVC conduit shall be measured as 1 unit. Note2- Rate of Cutting chasing of existing wall and making good of disturbed surface for concealed conduit shall be included in this item.

S&F 20 amp, 240 volt single pole and neutral enclosure with two pin and earth plug socket metal enclosed plug top in power coated CRCA steel sheet enclosure recess mounted with chained metal cover for socket outlet with and including one number single pole 'C' series MCB 20 amp as required complete all as specified and directed

M&L for earthing with galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised iron strip 32 x 6 mm earth lead by means of steel bolts, nuts, check nuts and washers all as shown in electrical plate no 3 of MES Schedule Part-I connected to earthing point and testing on completion with and including 40 mm bore light grade G.I. protection pipe (upto 7.5 metre beyond outer edge of earth pit) PCC pit in mix 1:3:6 type C1 with RCC 1:2:4 type B-1 40 mm thick cover reinforced with 6 mm dia M.S bars 3 nos both ways with lifting hook made out of 6 mm dia bar, watering arrangement with funnel and wire mesh and 20 mm bore medium grade G.I. watering pipe, common salt and charcoal filling, necessary excavation and earth work complete. Note:- Excavation for earthing to be done manually and Earth resistance below 3 Ohm should be obtained after measurement for every pit complete all as specified and directed

S&F in replacement MCB distribution board, powder coated, TPN , 415 volts, 4 ways,CRCA steel sheet, degree of protection IP 43 - IK 09 with reversible double door, recess mounted, having insulated 200 amp tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required complete all as specified and directed

S&F MCB distribution board, powder coated, SPN , 240 volts, 8 ways,CRCA steel sheet, degree of protection IP 43 - IK 09 with reversible double door, recess mounted, having insulated 200 amp tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required complete all as specified and directed

S&F MCBs of 'B' series having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs of Single pole 6 to 32 amp complete all as specified and directed.

S&F MCBs of 'C' series having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs of Double pole 10 to 32 amp complete all as specified and directed.

S & F in repair MCB Triple pole neutral(TPN) 63 Amps,10 KA, ISI marked, for inductive load connected through cable lugs of suitable size complete all as specified and directed .

S&F in repair 20 watt LED (1.2M) smartbrite extra batten made of CRCA sheet housing with a PC glossy diffuser duly prewired connection having lumen not less than 2200 complete all as specified and directed.

S&F in repair LED fixture 10 watt having lumen output 100 lumens per watt including connection complete all as specified and directed.

S&F LED 35 watt street light smartbrite aluminium PDC housing with IK 07 protection PC glossy diffuser duly prewired connection having a nominal system lumen output of efficiency 100 lumens/ watt light watt and total power consumption not more than 35 watt including driver. It has a rated IP 66 with 5 KV inbuilt surge protection complete all as specified and directed.. (Note:- Bracket along with screw to fix on wall/surface duly painted by silver colour paint will be included in above quoted rate.)

S&F 10 watt LED T -lamp B-22 base (warm white/golden yellow) 1000 lumens complete all as specified and directed.

S&F PVC fresh air fan 250 mm sweep,230 V with louvers, fan motor and accessories complete including making connections complete all as specified and directed

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete as specified and directed.

S&F ceiling fan 1200 mm sweep 50 Hz AC 230 volts, BEE 5 star rated in white colour with fan motor, blade set , 0.45 meter galvanised iron down rod, with canopy complete all as specified and directed.

S&F in repairs Bulk Head light environfriendly ultra modern energy saving surface mounted decorative oval bulk head edge lit LED luminaire comprising of High brightness LED Lamp complete all as specified and directed.

M/S ROHIT CONSTRUCTION (BID ID -3156293)

MSR INFRATECH (BID ID -3155514)