COMPREHENSIVE MAINT OF LEAKAGE, SEEPAGE, EXTERNAL, PLASTER, RAIN WATER PIPES ETC IN ZONE A AND B AREA UNDER AGE (I) AYODHYA CANTT

Amount

Dismantling plain or corrugated steel sheeting of any gauge & thickness in roof covering complete all as speciifed and directed.

S&F Pre-painted galvalume aluminum zinc coating PPGL based corrugated / Trapezoidal steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws, complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating PPGL based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, eaves board, fixed with self tapping screws, complete all as specified and directed.

S&F 6 mm thick Asbestos cement, corrugated or semi-corrugated sheets in roofs, walls etc, fixed with L-type or J-type or cranked hook bolts complete all as specified and directed.

S&F 6 mm thick Asbestos cement two piece adjustable plain wing ridge, fixed with L-type or J-type or cranked hook bolts complete all as specified and directed.

M&L for cutting chases in brick walls, pinning in, making good to facings where required and pointing in CM (1:3) to ends or edges of landings steps, cills and cutting chases for concealed water tubing or conduit wiring etc and making good cutting exceeding 20 cm girth complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description and in any position complete all as directed by Engr-in-Charge.

M&L for mild steel work as in wind ties of roof, ridge, etc using flat iron of size 40x6mm or as directed by Engr-in-Charge including supply of new nuts, bolts, washers etc as required / ordered for securing complete all as specified and directed.

Dismantling of timber scantling 40 Sqcm and over in section, fixed in any position in framed work and the like complete all as specified.

M&L for steel work in tubular trusses, railings, grills etc including special shaped washer etc complete using ERW or induction butt welded tube complete all as specified and directed.

M&L for taking down existing roof treatment from roof and terrace surfaces, roughening old concrete surfaces by picking, sweeping clean and washing down with water to remove dust etc and providing water proofing treatment in the following steps and specifications:- (a) Applying crack seal compound of same manufacture of water proof to fill all cracks observed on the roof surfaces. (b) Applying cement slurry over concrete surfaces @ 3 Kg/sqm. (c) Rendering 15mm thick in cement mortar (1:4) mixed with & including water proofing compound as per manufactures’ instructions (not less than 3% by weight of cement) on cleaned concrete surfaces of roof and finishing the surfaces fair and even including curing the plastered surfaces for 7 days by ponding of water over the roof, (leveling course). (d) Applying evenly one coat of primer coating (diluted with water in the ratio as specified by Manufacturer) (min @100-110 Sqft per liter (diluted quantity)) on the cleaned plastered surfaces. The surface shall be left for air dry for minimum period of 2-3 Hrs. (e) Applying evenly one coat of elastomeric water proof coat in one direction (as specified by Manufacturers)(min@ 0.9-1.0 Sqm per ltr) and allow to air dry for 4-6 hrs before applying second coat in other direction perpendicular to the first one (as specified by Manufacturer) (min @0.9-1.0 Sqm per ltr. The total thickness of two coats shall be 0.5 to 0.6 mm. (f) The whole system shall be left for air cure for min Seven days (without any movement). Make : - Dr Fixit Newcoat Ezee or Berger Home Shield PU RoofKoat or Asian Paints Smartcare Damp Proof or as equivalent approved by AGE(I). Note : - (i) The waterproofing shall be carried out in the last stage of execution to avoid any damages during the execution. (ii) Payment against this item shall not be allowed till completion of all the stages of work for any slab. (iii) The work shall be executed through well-trained applicators as per manufacturer’s instructions after obtaining written approval from the AGE(I).

Disconnecting existing water storage tank of capacity exc 500 but n.exc 1000 litres , setting aside (or lowering if required) for repairs, etc and hoisting if required reconnecting and refixing in position complete all as specified and as directed.

Dismantling existing water storage tank of any description of capacity exc 500 ltrs but n.exc 1000 ltrs and removing from side complete all as specified and directed.

S&F rotational moulded polythine water storage tanks (ISI marked) of 500 ltrs capacity (cylinderical, vertical with closed top), hoisted and fixed in position complete all as specified in SSR Part-I and directed by Engr-in-Charge.

S&F 20 mm bore PTMT nipple suitable for HDPE water tank (minimum weight 45 gms) and fixed complete all as specified and directed.

S&F 20mm bore ball valves high pressure of PTMT (min weight -210 gms) with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe complete all as specified and directed.

S&F in repairs, 20mm bore ball valves high pressure of PTMT (min weight -210 gms) with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe complete all as specified and directed.

Taking up or down 20 mm dia bore steel tubing and conncection including cleaning for re-fixing or removal to store, complete all as specified and as directed.

S&F 20 mm dia bore galvanized iron tubing, medium grade with all fittings and fixed to walls and ceiling or laid in floor complete all as specified and directed by Engr-in-Charge.

Refixing old 20 mm dia bore steel tubing and connections in new or old position complete all as specified and directed by Engr in charge.

Taking up or down 15 mm dia bore steel tubing and conncection including cleaning for re-fixing or removal to store, complete all as specified and as directed.

S&F 15 mm dia bore galvanized iron tubing, medium grade with all fittings and fixed to walls and ceiling or laid in floor complete all as specified and directed by Engr-in-Charge.

Refixing old 15 mm dia bore steel tubing and connections in new or old position complete all as specified and directed by Engr in charge.

Taking down eaves, gutters and rain water pipes (any size or pattern) including all fittings, heads, shoes, bends, swan necks, etc and cleaning for refixing or removal to store complete all as directed by Engr-in-Charge.

S&F 110mm dia bore PVC (SWR) pipes, single socketed, fixed to walls in any length with rubber ring joints including all fittings and clamps etc complete all as specified and directed.

S&F 110mm dia bore PVC (SWR) bends of any radius complete all as specified and directed.

S&F 110mm dia bore PVC (SWR) branch pieces, single 'Y' / 'T', equal or unequal complete all as specified and directed.

M&L for complete removal of existing decorative treatment of any description on walls and applying 1.00 mm thick wall care putty and two coats of weather proof exterior emulision (APEX of Asain paint or equivalent) over a coat of exterior primer complete all as specified and directed.

S&F in repairs, 15mm dia bore CP brass centre hole basin mixer for wash hand basin for mixing hot and cold water, screwed down for iron pipe complete all as specified and directed. Make - Jaquar cat Part No: FUS-29023B or equivalent as approved by AGE (I).

S&F in repairs, 15mm dia bore bib taps with wall flange, fancy type, cast copper alloy with capstan head, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. Make- Jaquar cat Part No-FUS 29037 or equivalent as approved by AGE (I)

S&F in repairs, 15mm dia bore angle / stop valve, cast copper alloy, screwed down, high pressure with crutch of butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

Hackingout old broken / serviceable glass of any description from old wooden or metal frames complete all as specified and directed.

S&F 3mm thick sheet glass of ordinary quality in panes n.exc 0.5 Sqm in each pane, fixed to metal frame with oil putty including renewal of glazing pins or to wooden frame with beadings etc complete all as specified and directed

S&F in repairs, galvanished mild steel wire cloth 0.56mm nominal dia and 1.18 mm average width of apperature, fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

Taking down cement of cement lime plaster from brick walls including raking out joints, hacking for key, scrubbing down with water to receive plaster and rubbish off the premises complete all as specified and directed.

M&L for 15 mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar (1:4) mixed with & including water proofing compound as per manufacturer's instructions (not less than 3% by weight of cement), finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparing newly plastered surfaces of walls and applying two coats of Acrylic smooth exterior paint of required shade (two or more coats applied @ 1.67 Ltr/10 Sqm) over a priming coat of exterior primer applied @ 2.20 Kg/10 Sqm complete all as specified and directed.

M&L for preparing newly plastered surfaces of walls and applying two coats of cement based paint over a coat of alkali resistant primer complete all as specified and directed.

M&L for 10 mm thick rendering on fair faces of brick work or concrete surface in cement mortar (1:6) as on internal surfaces of walls, finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparing newly plastered or previously untreated surfaces of walls and applying two coats of oil bound distemper over a coat of 1.00mm thick wall care putty, complete all as specified and directed. Note : Approval of Engr-in-Charge to be obtained by the contractor for preparation of surfaces before applying finishing work.

M&L for 5 mm thick rendering on fair faces of concrete surfaces of ceiling in cement mortar (1:3), finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparing newly plastered surfaces of ceiling and applying two coats of white wash complete all as specified and directed.

Demolition of brick work or stone / boulder masonry built in cement mortar or cement lime mortar complete all as specified and as directed.

M&L for brick work with old size sub class 'B' bricks in cement mortar (1:6), straight or curved on plan exc 6 m mean radius complete all as specified and directed.

Taking down old chowkhats or frames with shutters (without taking off shutters from the frame) exc 1.5 Sqm but n.exc.4 Sqm each complete all as specified and directed.

Taking down old chowkhats or frames with shutters (without taking off shutters from the frame) n.exc 1.5 Sqm each complete all as specified and directed.

S&F Powder coated (minimum thickness of powder coating 50 micron) anodised aluminium frames for door, windows, ventilators, partitions etc. with one or more rebates including joining cleats for fixing etc complete all as specified and directed.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws complete as per architectural drawings and the directions of Engineer-in-Charge.

S&F 18/19mm thick prelaminated particle board, exterior grade prelaminated one side with decorative choice lamination and on other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples, complete all as specified and directed.

M&L for aluminium anodised grill of design DG 104 pattern, made out of 10mm dia rod fixed with and including standard aluminium frame of 'F' Section of size 23.40mm x 15.30mm x 1.40mm thick all as per manufacturer's instructions, complete all as per specified and directed. Make: M/s DECO Grill or equivalent as approved by AGE (I) Note: Min thickness of anodising shall be 15 micron.

S&F 150 mm long floor door stopper of alluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, complete all as specified and as directed.

S&F 100mm size brass Mortice lock, 4 levers, vertical type and fixed complete all as specified and directed.

S&F double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed all specified and directed.

S&F 150 mm size aluminium handles, cast type, anodised and fixed complete all specified and directed.

S&F 125 mm size butt hinges, heavy weight, cold rolled mild steel and fixed complete all specified and directed.

S&F aluminium extruded section door closer hydraulicaly regulated designation No. 3 Universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg complete all as specified and as directed.

Jairajyadav security services

SAI RAM ASSOCIOATES

Saket Traders

K R KAUSHAL AND SONS

ABC CONSTRUCTION CO