85913 SPECIAL REPAIR TO STORE ROOM, JCOS/OR COVID WARD, JCOS/OR FAM WARD AND RESP-I WARD, F-I WARD OF BLDG NO. NP-94 (MAIN HOSPITAL BLDG) AT AICTS PUNE UNDER GE (S) PUNE

Amount

B/R PORTION Demolition of reinforced cement concrete in roof, floors (other than ground floor), beams, stair case, landing, chhajas and similar suspended work including reinforced cut on required to facilitate complete all as specified and as directed.

Demolition of cement concrete in roof, floors (other than ground floor), beams, stair case, landing, chhajas and similar suspended work including old APP membrane layer complete all as specified and as directed.

Demolition of cement concrete in ground floors and paving ( below and above other ground level ) including old floor tiles complete all as specified and as directed.

M&L for 40 mm thick PCC 1:2:4 type B0 (Using 12.5 mm graded stone aggregate) as in levelling course complete all as specified and as directed.

M&L for 20-22 mm thick Machine cut Kota stone slab flooring over and including 20 mm thick cement screed base in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L for 20-22 mm thick Machine cut Kota stone slab in riser of steps, skirting , dado and pillar laid over and including 15 mm rendering in CM 1:4 and filleting on top, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L for light shade/ double charged/shade ultracharged vitrified ceramic tiles 8 to 10mm thick (square/rectangular) polished, area of each tiles exceeding 0.36 sqm but not exc 0.42 sqm in floor etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match with and including 20 mm thick screed in cement sand mortar 1:4 for laying in floor finished complete all as specified and directed.

M&L for light shade/ double charged/shade ultracharged vitrified ceramic tiles 8 to 10mm thick (square/rectangular) polished, area of each tiles exceeding 0.36 sqm but not exc 0.42 sqm, set and jointed in neat cement slurry and pointed in white or coloured cement to match with and including 15 mm thick rendering in cement sand mortar 1:4 for laying in vertical surfaces such as skirting , dados and riser to step etc. and filleting at top etc complete all as specified and directed.

M&L for light shade/ double charged/shade ultracharged vitrified ceramic tiles 8 to 10mm thick (square/rectangular) polished, area of each tiles exceeding 0.42sqm but not exc 1 sqm in floor etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match with and including 20 mm thick screed in cement sand mortar 1:4 for laying in floor finished complete all as specified and directed.

Dismantling of wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises complete all as specified and as directed.

M&L for glazed coloured digital printed ceramic tiles of size 600 mm x 300mm x 7mm thick in vertical surfaces etc set and jointed in neat cement slurry and pointed in coloured cement to match with colour tiles with and including 15 mm thick backing coat in CM (1:4) and filleting at top etc complete all as specified and as directed.

M & L for non skid ceramic coloured joint free tiles 7 to 8 mm thick (square / rectangle ) area of each tiles exc 0.18 sqm but not exc 0.38 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement laying with and over 15 mm thick screed bed in CM 1:4 complete all as specified and as directed.

S & F WHB round bowl type counter top of size 520 x450 mm including CP waste coupling with waste pipe complete fittings coloured fixed in 18 mm thick polished granite 900 x 600 mm size including taking down old unserviceable WHB of any size / type complete all as specified and as directed. (Note : Granite top shall be mesured and paid seperately).

S&F in repairs Pillar taps long neck with aerator CAT No CON -021KN screwed for iron pipe and fixed complete all as specified and as directed.

S & F in repairs Vitreous china Wash down water closet (Pedestal pattern) white including connecting to drain and flushing pipe, anti-syphonage pipe and fixing plastic WC seat cover closed pattern with recessed bottom and mild steel chromium plated or aluminised hinging device etc complete all as specified and as directed.

S & F in repairs PVC valveless, syphonic action type 10 Ltr cap flushing cistern, low level, white, with inlet, ball valve, float and handle including bracket and connect to pipes etc. complete all as specified and as directed.

S&F in repairs 15 mm bore dia Stop valves Fancy type, cast copper alloy, chromium plated and cup (concealed type), screwed down, high pressure, with cruch or butterfly handle , screwed down, screwed for iron pipe or for union and fixed complete all as specified and as directed.

S&F in repairs bib taps long body suitable for 15mm bore dia of pipe, chromium plated, cast copper alloy with crutch or butterfly handle, fancy type, screwed down, screwed for iron pipe or for brass ferrule etc complete all as specified and as directed.

S&F in repair health faucet 15mm bore and flexible tube 1.00 mtr long fixed to plugs with chromium plated brass screw with and including two in one chromium plated bib tap complete all as specified and as directed.

S&F in repairs stainless steel double soap dish complete all as specified and as directed.

S&F in repairs stainless steel Robe Hook (khuti) with 5 Hook complete all as specified and as directed.

S&F in repair 20 mm dia Tubular towel rail brass chromium plated D type , 60 cm long between flange complete all as specified and as directed.

S&F in repairs glass corner round (9" x 9" )with satinless steel railing complete all as specified and as directed.

S&F 100 mm dia round Stainless steel Grating with waste hole complete all as specified and as directed.

S&F 100mm dia round Stainless steel Grating suitable for nahani trap complete all as specified and as directed.

S&F in repairs 32/40 mm bore PVC flexible waste pipe connecting to waste fitting for WHB /Sink complete all as specified and as directed.

S & F in repair PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and as directed.

Material and labour for Water proofing treatment to sunken slab, walls, etc, and shall be carried out as specified below and as directed by Engineer-in-Charge. (a) Clean the sunken portion of toilet/Baths/WCs/Kitchen thoroughly remove laitance, dirt, dust etc. (b) Form angle fillet of size 40 mm x 40 mm along the junction of wall and floor using polymer modified mortar (“ Dr fixit” Pidicrete URP” or eqvt). (c) Sanitary pipes entering through walls and floor shall be sealed with “Dr Fixit Bath seal Tape” and the gaps to be grouted with non-shrink cementitous grout “Dr Fixit Bath seal Grout” or eqvt. Nahani traps etc to be fitted securely and the gaps around it to be grounted in the same manner. (d) Apply one coat of a Bitumen-modified polymer coating “Dr Fixit Bath seal Plus” or eqvt on all angle fillets by brush and cover it with 100 mm open woven mesh when it is still wet. Apply second coat of the same coating on the angle fillets and allow it to dry completely.

(e) In the remaining area, in dry substrate condition brush apply first coat of the same coating and further apply second coat when first is dry. Extend the coating upto 150mm above the FFL. Above FFL, another cementitious waterproofing waterproof coating “Dr Fixit Pidifin 2 K” or eqvt can be further applied right upto 2.1 m to waterproof the shower area also, if it is a bathroom or bath cubicles of a sanitary annex and apply second coat after 6-8 hours and allow to dry completely. (f) After 2 to 3 days, sunken portion must be over laid with a 50 mm thick concrete screed M15 (Nominal Mix) mixed with integral WPC (Liquid) laid to slope 1:60 towards outer face of wall. Provide 40 mm OD UPVC pipe at the lowest point with 300 mm projection beyond the outer face of the wall. Then fill up the sunken portion with lean concrete 1:4:8 type D2. (g) After completing plumbing work in the toilet/WC/Bath/Kitchen floor, tiling work (floor and dado) can be carried out using suitable Tile Adhesives and ready to make tile grouts of approved makes such as Dr Fixit, FOSROC SIKA, MC BUCHEMIE, ROFF, etc.

Dismantling ceiling /wall lining/ boarding of any description, fixed in any position like ceiling, lining, partition etc with nails including frame work complete all as specified and as directed.

S&F false ceiling with 9 to 9.5 mm thick glass fibre reinforced Gypsum ceiling tiles of size 595 X 595 mm ,prima fine fissured micro look white coloured laid over including grid work 600x600mm using GI powder coated “T:” section grid as Main 'T' 38 X25 mm , cross 'T" 25x25mm and wall angle 25x25mm grid and 6 mm dia GI suspension wire etc complete all as specified and directed.

M&L for 40 mm thick PCC 1:2:4 type B0 (Using 12.5 mm graded stone aggregate) mixed with water proofing compound as per manufacturer's instruction and finishing cement concrete surface even and smooth using with extra cement on roof complete all as specified and as directed. (Note : Water proofing compound shall measured and paid separately )

M&L for water proofing treatment by applying primer @ 0.70 kg per sqm, providing and laying 3 mm thick APP modified bitumen based prefabricated five layer water proofing memebarane weighing not less than 3.60 kg per sqm reinforced with non woven polyester matt black finished weighing not less than 100 gm per sqm having softening point not less than 140º centigrade, longitudinal tensile strength not less than 300 N per sqm tearning strength of 100n by torch on application including minimum over lapping 10 cm on either side and 15cm on ends and applying two coats of bitumastic Aluminium paint over the membrane complete all as specified and as directed. (Note : (a) APP membrane shall also be laid in sunken floor and on sides upto finished floor level as per site requirement. (b) The water proofing treatment shall be carried out by the authorized applicators (c) Apply two coats of bitmastic Aluminium paint over the membrane. (d) Quoted rate shall deemed to be inclusive of all these aspects and no claim of what-so-ever nature shall be entertained.)

S&F three track sliding aluminium window with two or more shutters With 4 mm thick tinted glass and one shutters of stainless steel wire cloth 0.36mm nominal dia and 1.18mm width aperture for mosquito proofing with good quality bearing handles, locks, etc using rubber beading and glazing clip etc using following aluminium powder coated sections conforming to catalogue of 'JINDAL' or equivalent make complete all as directed by Engr-in-charge. (a) Bottom frame - 20620 (b) Shutter top & bottom - 20844 (c ) Shutter side - 20606 (d) Top frame and slide - 20621 (e) Shutter interlock - 20845 (f) Glazing clip - 19352 (Note : Work under this item shall be executed as per drg No. CEPZ/2013/TD/01 (sheet No.1/2 dt 14 Jan 2013 available in Office of GE (S) Pune. The contractor shall refer the same prior quoting tender. Quoted rate shall deemed to be inclusive of this provision irrespective of the fact whether contractor referred the same or not. Contractor's claim of what-so-ever nature on this account shall not be entertained.)

S&F aluminium powder coated ventilators/louvers 5 mm thick x 10 cm wide frosted glass strips and including one shutter of stainless steel wire cloth 0.36 mm nominal dia and 1.18 mm width aperture for mosquito proofing etc following aluminium powder coated section conforming to catalogue of Jindal or equivalent make and rubber beading etc complete all as spd and directed by EIC. (a) SP- 20048 (b) Glazing clips-19352

Demolition of stone slabs and tiles of any description or thickness in floors, laid bedded and pointed in any mortar , including cement mortar bedding and removing rubbish off the premises complete all as specified and directed

M&L for 20 mm thick Granite slab (of any type/colour) work (table rubbed and polished) in steps, pillars;window cills/jamb, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite as counters of any radius etc laid with and over 15mm thick screed bed in CM (1:4) complete all as specified and directed.

M&L for rounding to edges of granite stone slabs one edge polishing such as in steps, cooking platform and similar work complete all as spd and directed.

Taking down chowkats or frames wooden/steel with shutters (w/o taking off guard bar from frames) not exc 1.5 Sqm each complete all as specified and as directed.

Taking down chowkats or frames steel window with shutters (w/o taking off guard bar from frames) exc 1.5 Sqm but not exc 4 sqm each complete all as specified and as directed.

Taking down chowkats or frames wooden / pressed steel door frame with wooden shutters exc 1.5 Sqm but not exc 4 sqm each complete all as specified and as directed.

Taking down shutters of any description exceeding 1 Sqm but not exc 2 sqm each complete all as specified and directed

Taking down shutters of any description not exceeding 1 Sqm each complete all as specified and directed

S & F solid PVC door frame of size 50mmx95mm made out of 5mm thick wooden grain printed PVC sheet rainforced with MS tube supplying and fixing in opening complete all as specified and as directed.

S & F factory made solid PVC moulded door shutters 28 to 30 mm thick (stiles) with 2,4 or 6 raised panels design with 2mm thick moulded PVC sheet on front face & 2 mm plain colour PVC sheet on back face, supplying & fixingued solid in frame at site as per specification & drgs with particle board core etc.including 3mm thick, 1st Class HW (TW) beading all around on edging and welding 3 Nos MS but hinges size100mm with existing MS frame all as specified and directed by Engr-in-Charge.

S&F Pressed steel farmes 125 mm x 60 mm for doors with one or more rebates including necessary fixing lungs, hinges, lockstrick plate etc. and filling of hollow of frame with cement concrete or cement mortar complete all as spd and directed. (Note : Cement concrete shall be measured and paid seprately )

S&F for 35 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both faces is coverde with decorative face 1.5 mm thick veneer with lapping all around of the shutter / frame to match complete all as specified and as directed.

S&F 35 mm thick second Class hard wood factory made Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., divided in to squares with plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in SSR Pt-I Section 8, clause 8.24 (a) complete all as specified and directed

S&F 35 mm thick second Class hard wood factory made Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., divided in to squares with plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters and cover with both side decorative face 1.5 mm thick veener as specified in SSR Pt-I Section 8, clause 8.24 (a) complete all as specified and directed. (Note : Decorative veener shall be measured and paid separately )

S & F Stainless steel wire cloth, 0.36 mm dia of wire and average width of aperture 1.18 mm and fixed with stainless steel wire staples complete all as specified and directed

Taking down shutters and refixing in same opening / frame after supplying and fixing both side decorative laminate on old wooden painted surfaces of any description exceeding 1 Sq. M but n.exc 2 sqm each complete all as specified and directed. (Note :- Decorative face veener shall be measured and paid seprately )

S&F in repair 125mm long hinges heavy weight stainless steel mild steel hinges pin, bright polished and fixed complete all as specified and as directed.

S&F 1.5 mm thick decorative laminates type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer instructions complete all as specified and directed.

S&F 375mm Mild Steel spring for doors, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

M&L for Extra over flush shutters, any thickness, for vision panels or peep holes, square or rectangular including lipping complete all as specified and directed. (Note : Supplying and fixing of glass shall be measured and paid separately)

S&F for 25 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both faces is covered with and incl 0.90 mm thick decorative face veneer with lapping all around of the shutter / frame to match complete all as specified and as directed.

M&L for 12 mm thick plywood, grade BWP, type BB (7 Nos of ply ) fixed with screws to timber frame work with 0.9 mm thick decorative laminate complete all as spd and as directeed. (Note : Decorative laminate shall be measured and paid separately).

S&F 0.9 mm thick decorative laminates type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer instructions complete all as specified and as directed.

M&L for frame work such as grills guard bars, barred iron doors, ladders railing, gratings, etc end bars shouldered and /or riveted and similar work con-forming to Fe 290 Gde-E-165 complete all as specified and as directed.

S&F Second Class hard wood (Sal) plain, solid, straight as in chowkat and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed .

S&F 150 mm Hasp and Staple, stainless steel safety , including bolt to hinge plate and fixed complete all as specified and as directed.

S&F 100 mm Hasp and Staple, stainless steel safety type, including bolt to hinge plate and fixed complete all as specified and as directed.

S&F 100 mm long stainless steel handles, ISI marked complete all as specified and directed .

S&F continuous Piano hinges, mild steel bright finished or electro galvanised width of flap 30 mm complete all as specified and as directed.

S&F of Magnet catches and striking plate complete all as specified and as directed.

S&F 375 mm length brass sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts not less than 12 mm dia with and including a minimum 6 bolts and nuts, four on bolt plates and two on staples plate complete all as specified and as directed.

S & F 300 mm long Brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed complete all as specified and as directed.

S & F 150 mm size extruded brass handles, fabricated type polished complete all as specified and as directed.

S&F floor door stopper of brass body and tongue with hard drawn steel spring, fixed in floor, 150mm overall length of cover plate complete all as specified and as directed.

S&F 125 mm long butt hinges cast brass heavy weight but mild steel hinges pin, bright polished and fixed type B-12 complete all as specified and as directed.

S&F 125 mm long hinges heavy weight , cold rolled mild steel and fixed complete all as specified and as directed.

S&F 300 mm long stainless steel, sliding door bolt, with bright bolt not less than 12 mm dia with and including minimum 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and as directed.

S&F in repair 300 mm long stainless steel, sliding door bolt, with bright bolt not less than 12 mm dia with and including minimum 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and as directed.

S&F floor door stopper of stainless steel double stopper, high grip and tongue with hard drawn steel spring, fixed in floor, 150mm overall length of cover plate complete all as specified and as directed.

S&F 150 mm long stainless steel, tower bolt ISI marked complete all as specified and directed.

S&F 200 mm long stainless steel, barrel tower bolts ISI marked complete all as specified and directed

S&F in repairs 200 mm long stainless steel barrel tower bolts ISI marked complete all as specified and directed

S&F 150mm long stainless steel handles, ISI marked complete all as specified and directed.

S&F in repairs 150mm long stainless steel handles, ISI marked complete all as specified and directed.

S&F 100mm long extruded aluminium alloy with galvanised mild steel hinges pin, anodised and fixed, type C-21 complete all as specified and as directed.

S & F anodised aluminium powder coated frame for doors, with one or more rebates including joining cleat for fixing etc. complete all as specified (JINDAL section 20078 ,A- 101.60 , B- 44.45 C- 2.01, D- 8 weight 1.605 Kg /Rm ) complete all as specified and as directed.

S&F of aluminium powder coated single leaf door on pivots alongwith , door lock, handles, including 5mm thick glass panel etc fixed with rubber beading and glazing clips and using following powder coated sections conforming to catalogue of 'JINDAL' or equivalent make complete all as directed by Engr-in-charge. (a) Rectangular tube-14005 (b) Shutter vertical-19518 (c ) Shutter top rail-19582 (d) Shutter middle rail-19564 (e) Shutter bottom rail-19511 (f) Glazing clip - 19352

S & F double action floor spring hydraulically regulated made up of minimum 1.25mm thick alloy sheet foundation box, with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty of approved make complete all as specified and directed by Engr-in-Charge.

S&F in repair Aluminium (Extruded section body door closer hydroulically regulated designation No.3 universal type, suitable for door shutter of 851 to 1000 mm in width and weight between 61 to 80 Kg complete all as spciefied and directed.

S & F Sticky vinyl self adhesive decorative glass film for glass complete all as specified and directed. (Note : Design of glass film shall be as approved by EIC)

S&F in repairs 20 mm dia Stainless steel 304 pipe for fancy type curtain rod (weight not less than 1.68 kg/ Rm) including fancy type bracket, stops roller etc complete all as specified and directed.

S&F Stainless steel 304 fancy type curtain rod caps/side bulbs etc to be fitted in 20mm SS curtain rod pipe complete all as specified and directed.

Taking up or down 15 mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

Taking up or down 20 mm bore steel tubing and connections, including cleaning for Refixing or removal to store complete all as specified and as directed.

Taking up or down 25/32 mm bore steel tubing and connections, including cleaning for Refixing or removal to store complete all as specified and as directed.

S & F 15 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc. with & including necessary fittings, fixed to walls and ceilings or laid in floors complete all as specified and as directed.

S & F 20 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc. with & including necessary fittings, fixed to walls and ceilings or laid in floors complete all as specified and as directed.

S & F 25 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc. with & including necessary fittings, fixed to walls and ceilings or laid in floors complete all as specified and as directed.

S & F 32 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc. with & including necessary fittings, fixed to walls and ceilings or laid in floors complete all as specified and as directed.

Refixing old 20 mm bore GI tubing and connections on new or old position (walls, ceilling, floor etc) complete all as specified and as directed.

Refixing old 25/32mm bore GI tubing and connections on new or old position (walls, ceilling, floor etc) complete all as specified and as directed.

M & L for cutting existing 15 or 20mm bore GI tubing for alteration or addition of sizes including screwing existing GI tubing for tapping & making new connections etc complete all as specified & directed by Engr-in-Charge.

S&F in repairs 20 mm bore Gun-metal, globe or gate valves cast copper, with iron whees head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

S&F in repairs 25 mm bore Gun-metal, globe or gate valves cast copper, with iron whees head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

S&F in repairs 32 mm bore Gun-metal, globe or gate valves cast copper, with iron whees head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc, and cutting chases for concealed water tubing or concealed conduit wiring, etc, and making good, cutting n.exc. 10cm girth complete all as specified and as directed.

Cutting in brick wall exc half brick but n. exc one brick in built in cement mortar or cement lime mortar and stone walls for inserting holdfast and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and as directed.

S&F rotational moulded high density poly-ethylene, three layered water storage tanks (cylindrical vertical with closed top) of capacity 1000 litre conforming to IS, hoisted and fixed in position incl dismantling existing water tank or removing to store complete all as specified and directed.

S&F rotational moulded high density poly-ethylene, three layered water storage tanks ( cylindrical vertical with closed top) of capacity 2000 liter and conforming to IS, hoisted and fixed in position incl dismantling existing water tank or removing to store complete all as specified and directed.

Disconnecting existing tanks exc 1000 & not exc 2000 lit capacity, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and refixing in position complete all as specified and directed.

Cleaning and removing all scale and dirt, etc, from tanks exc 1000 ltr but not exc 2000 ltr and from mouths of circulating pipes, etc complete all as specified and as directed.

S&F in repairs ball valves suitable for 20 mm bore iron pipe high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball, screwed for iron pipe and fixed (minimum weight 455 gms) complete all as specified and directed.

S&F ball valves suitable for 25 mm bore iron pipe high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball, screwed for iron pipe and fixed (minimum weight 455 gms) complete all as specified and directed.

Demolition and breaking up RCC, SWG drain pipes of sizes 75/100 mm bore set in cement mortar and removing debris from the site complete all as directed by Engr-in-Charge.

S&F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S&F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring including fixed in wall complete all as specified and as directed.

S&F 110mm bore PVC (SWR) pipe radius bends provided with access door complete all as specified and as directed.

S&F 110mm bore PVC (SWR) radius bends complete all as specified and as directed.

S&F 110mm bore PVC (SWR) branch piece,single (single Y) equal or unequal complete all as specified and as directed.

S&F 110mm bore PVC (SWR) branch piece, double (single Y) equal or unequal complete all as specified and as directed.

S&F 110mm bore PVC (SWR) junction double, (double T), equal or unequal with access door complete all as specified and as directed.

S&F 110mm bore PVC (SWR) vent cowl complete all as specified and as directed.

S & F 110mm bore PVC (SWR) WC connector bent type complete all as specified and as directed.

S & F PVC (SWR) gully trap 125/110 mm bore, setting and jointing with solvent cement complete all as specified and as directed.

S&F 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints and fixed in wall complete all as specified and as directed.

S&F 75mm bore PVC (SWR) branch piece,single (single Y) equal or unequal provided with access door complete all as specified and as directed,

S&F 75mm bore PVC (SWR) branch piece, double (single Y) equal or unequal with access door complete all as specified and as directed.

S & F 75mm bore PVC (SWR) junction double, (double T), equal or unequal with access door complete all as specified and as directed.

S&F 75mm bore PVC (SWR) bends provided with access door complete all as specified and as directed.

S&F PVC (SWR) bends 75 mm bore complete all as specified and as directed.

M & L for 75 mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed.

M & L for 75 mm bore PVC (SWR) mullti floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed.

M&L for RCC type B1, 1:2:4 (Using 20 mm crushed stone graded aggregate) as in slab supports on wall beams and column baloconies and shelves and like work complete all as specified and as directed.

Use and waste for Form to rough finish surface of concrete to sides and soffits of floor or roof beams, beam haunchings , girders , brressummers, lintels, cantilevers, shalves including sup-ports, over hanges,etc. also splays between floors and beams complete all as specified and as directed.

M&L for TMT bar 10 mm dia and over cut to length, bent to shape required including bending or hooking ends and binding with and including mild steel wire (annealed)not less than0.9 mm dia complete as in reinforcement complete all as specified and as directed.

M&L for TMT bar 8 mm dia and cut to length, bent to shape required including bending or hooking ends and binding with and including mild steel wire (annealed)not less than0.9 mm dia complete as in reinforcement all as specified.

Demolition of brick or stone/ boulder masonary, built in cement mortar complete all as specified and as directed.

M&L for old size fly ash bricks, straight or curved on plan exc 6 m mean radius built in CM 1:6 complete all as specified and as directed.

M&L for ACC Block (size 600 mm x 200 mm x 150 mm ) masonry work with straight or curved on plan to any radius, built in ready mix jointing mortar of joint thickness 3 to 4 mm and laying two Nos. 8mm dia TMT steel bars with 50mm thick cement concrete Type B0, 1:2:4 (using 12.5mm graded stone aggregate) after every four layers of blocks all as specified and as directed. (Note :- (i) MS TMT bar shall be measured and paid separetly (ii) Quoted rate shall be deemed to be included for scaffolding for masonry work upto 12 mtr height)

M&L for 50 mm thick precast cement concrete louvres and jallies, type B0 1:2:4 (12.5 mm graded stone aggregate) (measured solid) set in cement mortar 1:4 including dismantling of existing unserviceable jallies of any type complete all as specified and as directed.

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and as directed.

M&L for rendering 15 mm thick on fair faces of brick work in cement mortar 1:4 mixed with water proofing compound finished even and smooth without using extra cement complete all as specified and as directed. (Note : WPC shall be measured and paid seperately)

Supply only Integral waterproofing compound of approved make complete all as specified and as directed.

M&L for rendering 15 mm thick on fair faces of brick work in cement mortar 1:6, finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 5 mm thick in CM (1:3) on fair faces of concrete surfaces as in ceilling Chajjas finished fair and even without using extra cement complete all as specified and as directed

M&L for preparation of new plastered surface of wall and distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats over plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and as directed.

M&L for Complete removal of existing treatment of plastered surface of wall and distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats over plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and as directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed.

Material & Labour for compete removal of existing teratment and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over wall surfaces complete all as specified and as directed.

M&L for complete removal of existing surface of ceiling and applying 2 coats of oil bound distemper over 2 mm thick wall care putty complete all as specified and as directed.

M&L for preparation of new surface of ceiling and applying 2 coats of oil bound distemper over 2 mm thick wall care putty complete all as specified and as directed.

Material and labour for French polishing on old surface od wood of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on old works with two or more coats complete all as specified and as directed.

S&F in repair 100/110mm bore pipe Stack clamps out of 50mm by 5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stay to wall or roof complete all as specified and as directed.

S&F in repair 75mm bore pipe Stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stay to wall or roof complete all as specified and as directed.

Excavation in trenches not exc 1.5mtr wide and not exc. 1.5m in depth for foundation and getting out in soft/loose soil complete all as specified and as directed.

Removing excavated material not exceeding 50mtr and depositing where directed at a level n.exc 1.5 metre above the starting point all as specified and directed by Engr-in-Charge.

Returning filling in soil including spreading, levelling, watering and well ramming in layers not exc. 25cm complete all as specified and as directed.

M&L for PCC 1:4:8 type D2 (using 40mm crushed stone graded aggregate) as in bed to drain pipes complete all as specified and directed.

M&L for 75 mm thick Cement concrete 1:3:6 type C1, (using 20mm graded stone aggregate) as in flooring/ Plinth protection finish even & smooth with using extra cement complete all as specified and as directed.

M&L for cement concrete 1:2:4 type B0 (using 12.5 mm stone graded aggregate), as in roof kerbs, rounded chamfered on edges, in lintel upto 1.5m clear span, cill, steps, seismic and other similar bands, plinth courses string courses, lacing courses, copings kneelers, apex including weathering, slightly rounded or chemfered angles and throating etc. including necessary form work complete all as specified and as directed.

M&L for dubbing out average 15mm thick in CM 1: 4 on irregular face of concrete surface (pillar, beam, facia etc) over incl 10 mm thick in CM 1:4 mixed with water proofing compound plaster (when specifically ordered in writing) complete all as specified and as directed. ( Note : (i) WPC shall be measured and paid seperately (ii) Area of each paches plastring not 1 exc Sqm (iii) Quoted Rates shall deemed to be included for scaffolding for work upto 12 Mtr height)

Removing the demolished bldg materials etc. to a distance of exc 5 Km out of defence area including loading, unloading and stacking at the destination complete all as specified and as directed.

S&F 18/19 mm thick Block Board, grade I quality exterior grade type with and including 0.90 mm thick decorative face veneer on both faces including lapping of edges fixed with screws to timber frame work as in CB partition and shelf and other works including dismantling of boarding of any description, fixed in any position with nails complete all as specified and as directed.

E/M PORTION Taking down carefully exising unserviceable aluminium point wiring (light, fan, socket or power), complete (fitting such as switches,ceiling rose, pendent, regulators etc) removing material to store for keeping in safe custody or for taking credit (credit for the items should be made as per conditions separately) and making good disturbed surfaces of wall, floor etc. complete all as specified and as directed.

M & L for Point wiring using approved colour coding as per IS, with multistranded copper conductor 1.5 Sqmm (nominal area), two single core, PVC insulated and unsheathed FRLSH cable 1100 volts grade ISI-694 marked drawn through in and including heavy duty, PVC concealed conduit of white/ ivory colour including all accessories ISI marked after cutting chasing in wall/ceiling etc, with GI Flush boxes 1.2 mm thick, 60 mm deep with earth dolly duly, covered with modular white cover plate with frame suitable for modular switches, including PVC insulated multistranded copper conductor 1.5 Sqmm (nominal area) single core FRLSH cable as earth continuity conductor to common earth and connecting to earth dolly all as specified and directed for the following :-

One light point controlled by one way switch 5 Amps complete all as specified and as directed.

One fan/ exhaust/ fan point controlled by one way switch 5 Amps complete all as specified and as directed.

One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent board complete all as specified and as directed.

One 3 Pin point 5 Amps switch socket outlet point controlled by one switch on the same board complete all as specified and as directed.

One Bell/Buzzer points controlled by one bell push complete all as specified and as directed.

All as per item No. 162.00 above but for modular socket power point with stranded copper conductor 2.5 Sqmm (nominal area), single core, PVC insulated and unsheathed multistranded FRLSH cable 1100 Volt grade ISI-694 marked for 3 pin, 15 Amp socket outlet on independent board including PVC insulated multistranded copper conductor 2.5 Sqmm (nominal area) single core FRLSH cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and as directed.

S & F Modular switch one way 6 Amps, 1 module complete all as specified and as directed.

S & F Modular switch one way 16 Amps, 1 module, with neon indicator complete all as specified and as directed.

S & F celling rose 2/3 terminals, PVC/ polycarbonate, isolated body ISI marked complete all as specified and as directed.

S & F modular step type fan regulator 120 watt single module suitable for operation on 230 volt 50 HZ AC supply complete all as specified and as directed

S & F Modular socket, 6 Amps, 2/3 pin combination 2 module complete all as specified and as directed.

S & F Modular socket, 6/16Amps, 2/3 pin combination 2 module complete all as specified and as directed.

S&F Bell Electric Ding dong type suitable for operation on 230 volt 50 HZ A C supply complete all as specified and as directed

S & F modular Bell push 6 Amps single module complete all as specified and as directed.

Supply and fixing LED lights fitting 1 x 18W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose including taking down old unserviceable light fitting of any type complete all as specified and as directed.

Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size including taking down old unserviceable light fittings of any type complete all as specified and as directed.

Supply and fix LED mirror light fitting LINNET 2' long wall mounted type high efficiendcy 1 x 14 watt with high output diffuser and all fixing arrangements including taking down old unserviceable light fittings of any type complete all as specified and as directed.

S&F fixing lamp holder insulated body with back plate PVC/Polycarbonate type with cord grip cap, angular type fixed on wall including taking down old unserviceable lamp holder of any type complete all as specified and as directed.

M&L for Sub main wiring with approved colour coding as per IS with two single core PVC insulated FRLSH cable with stranded copper conductor of size 4 Sqmm nominal cross sectional area, 1100 Volts grade, stranded, PVC insulated, unsheathed, copper conductor FRLSH cable, conforming to IS with and including continuous earth wire of size 4 Sqmm nominal cross sectional area, single core, PVC insulated, copper conductor cable drawing into and including non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessories ISI marked of suitable size concealed in wall etc and connected to common earth dolly including all cutting / chases etc in any type of wall, making good to the disturbed surfaces to match with the existing finishes complete including taking down of old sub main wiring, complete all as specified and directed. (Note:- Two runs of 4 sqmm cable and one run of 4 sqmm cable of earth continuity conductor and one run of PVC pipe shall be measured as one unit length.)

M&L for Sub main wiring with approved colour coding as per IS with two single core PVC insulated FRLSH cable with stranded copper conductor of size 6 Sqmm nominal cross sectional area, 1100 Volts grade, stranded, PVC insulated, unsheathed, copper conductor FRLSH cable, conforming to IS with and including continuous earth wire of size 6 Sqmm nominal cross sectional area, single core, PVC insulated, copper conductor cable drawing into and including non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessories ISI marked of suitable size concealed in wall etc and connected to common earth dolly including all cutting / chases etc in any type of wall, making good to the disturbed surfaces to match with the existing finishes complete including taking down of old sub main wiring, complete all as specified and directed. (Note:- Two runs of 6 sqmm cable and one run of 6 sqmm cable of earth continuity conductor and one run of PVC pipe shall be measured as one unit length.)

M&L for Sub main wiring with approved colour coding as per IS with Four single core PVC insulated FRLSH cable with stranded copper conductor of size 10 Sqmm nominal cross sectional area, 1100 Volts grade, stranded, PVC insulated, unsheathed, copper conductor FRLSH cable, conforming to IS with and including continuous earth wire of size 10 Sqmm nominal cross sectional area, single core, PVC insulated, copper conductor cable drawing into and including non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessories ISI marked of suitable size concealed in wall etc and connected to common earth dolly including all cutting / chases etc in any type of wall, making good to the disturbed surfaces to match with the existing finishes complete including taking down of old sub main wiring, complete all as specified and directed. (Note:- Four runs of 10 sqmm cable and Two runs of 10 sqmm cable of earth continuity conductor and one run of PVC pipe shall be measured as one unit length.)

S&F IP-43, IK 09, protection metal double door Vertical TPN-DB with 200Amps rated busbar of each phase and neutral busbar, 415 volts, 50 HZ complete with interconnection links, blanking plates, cable ties, identification labels TPN 8 way, 24 modules suitable for accommodating upto100 Amps MCCB 4 pole as incomer and SP/TP MCB as out going and concealed in wall including all cutting holes in or through walls, making good to walls, ceiling etc including two coats of white / colour washing / distempering etc to the disturbed surfaces to match the existing finishes complete all as specified and as directed.

S&F MCB SPN DB 8 way, double door, with 200 amp rated busbar 240V, SPN concealed in wall incl. all cutting holes in or through walls and making good to walls including taking down old unserviceable MCB DB of any size & capacity complete all as specified and as directed.

S&F MCB SPN DB 12 way, double door, with 200 amp rated busbar 240V, SPN concealed in wall incl. all cutting holes in or through walls and making good to walls including taking down old unserviceable MCB DB of any size & capacity complete all as specified and as directed

S&F MCB SPN DB 04 way, double door, with 200 amp rated busbar 240 V, SPN concealed in wall incl. all cutting holes in or through walls and making good to walls including taking down old unserviceable MCB DB of any size & capacity complete all as specified and as directed.

S & F Sheet metal, 20 Amp Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 amps,10 KA breaking capacity,'C' series, 240 V concealed in wall incl. all cutting holes in or through walls and making good to walls including taking down old unserviceable sheet metal enclosure of any type complete all as specified and as directed.

S&F MCCB 100 Amps, 16 KA, 4 Pole, 415V, electronic protection unit including taking down old unserviceable unit complete all as specified and as directed.

S&F MCCB 3 Pole, 415 V, Adjustable type, 160 Amps with breaking capacity 36 KA with SS MCCB enclosure concealed in wall incl. all cutting holes in or through walls and making good to walls and taking down old unserviceable MCCB of any capacity complete all as specified and as directed.

S&F MCB TPN 63 amps,10KA, 240V,'C' series complete all as specified and as directed.

S&F MCB SPN 40-63 amps,10KA, 240V,'C' series complete all as specified and as directed.

S&F MCB SP 6-32 Amps,10KA,'C' series complete all as specified and as directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep, 1400 RPM with, blades, and frame and louvers, including taking down old unserviceable exhaust for keeping in safe custody and deposit to MES Yard complete all as specified and directed.

Supply and fixing ceiling fans complete with blades, down rods(2/3 ft long), electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with silent brushless direct current copper motor and complete connection with 0.5 Sqmm X 3 core PVC sheated copper coductor including taking down old unserviceable fan for keeping in safe custody and deposit to MES Yard complete all as specified and directed.

Supply, installation, testing and commissioning of outdoor LT Panel size minimum (1 .0 X1.0 X 0.6)m suitable for AC 440 V , 50 HZ supply, fabricated with 3.14 mm, MS Steel sheet duly pre-treated and pure polyester thick powder coated 80 micron thickness using Siemens grey colour. The LT Panel shall be double door in cubical formation, compartmentalized in form with front open able doors. The door shall be provided with concealed hinges and with brazing wherever required to avoid deformation and shall be earthed. All the door shall have heavy duty door locks, and shall be sealed with neoprene gaskets. The LT Panel shall be IP-65, outdoor type weather , dust and vermin proof as per approved diagram. Panels shall have lifting hooks and base channel of size 40 X40 X5 mm. The LT Panel shall be complete with bus bars, wiring, cabling of proper ratings (not less than 1.5 times the rating of respective switchgears, control gear etc.) for inter connection between switch gear, control gear, metering , safety relays, indicators etc. as per the approved single line diagram. The LT Panel shall have proper arrangement for termination of all incoming and out goings cables.

Supply, lay, connecting and testing cable of size 70 Sqmm, 3.5 core, XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty), 1100 Volts grade with earthed system, stranded aluminium conductor including making input and output connections with using suitable size of thimbles, lugs, and glands including taking down old unserviceable cable of any size & capacity complete all as specified and directed,

Supply, lay, connecting and testing cable of size 10 Sqmm, 4 core, XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty), 1100 Volts grade with earthed system, stranded aluminium conductor including making input and output connections with using suitable size of thimbles, lugs, and glands including taking down old unserviceable cable of any size & capacity complete all as specified and directed.

M&L for Earthing connected with Bldg main Lightening arrestor etc. with galvanised iron earth plate of size 600 x 600 x 6 mm thick burried directly in ground not less than 2.5 mtr below grond level, earth plate paced on all side with charcoal mixed with salt to a thickness of 150 mm connected by GI earth strip of size 32 x 6 mm thick soldered and revetted to earth plate attesters. GI earth strip will be protected by using 50mm bore GI pipe (light grade) including flat iron clamp 32 x 3 mm including bolts, nuts & washers complete. The earthing includes necessary excavation, PCC pit, CI cover with frame duly grouted with PCC, watering pipe 20 mm bore, funnel with wire mess etc all as specified and shown in electrical plate No. 3 of MES schedule Part-I including testing on completion all as specified and directed by Engr-in-Charge. (Note :- (i) The unit rate shall also including earth work in any type of soil, PCC 1:3:6, type C1 for chamber, CI cover with frame duly grouted with PCC funnel with GI watering pipe 20mm dia light grade, GI protection pipe light grade 50mm dia and wire mesh. (ii) Cost of earth lead and protection pipe upto 7.5 shall be deemed to be included in quoted rates)

M&L for earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point including testing on completion complete all as specified and as directed. (Note :- (i) The unit rate shall also including earth work in any type of soil, PCC 1:3:6, type C1 for chamber, CI cover with frame duly grouted with PCC funnel with GI watering pipe 20mm dia light grade, GI protection pipe light grade 15mm dia and wire mesh (ii) Cost of earth lead and protection pipe upto 7.5 shall be deemed to be included in quoted rates)

M & L for fixing earth continuity conductor or main earth lead fixed to wall or buried in ground or drawn in GI pipe with 4mm GI Wire complete all as specified and as directed.

Material and labour for GI tubing light grade, 15mm dia with all necessary fittings fixed on walls for Earthing lead protection fixed with the clamps made out of FI 25 x 3mm duly painted with two coats of aluminium paint over a coat of approved primer etc complete all as specified and directed.

Supplying and laying GI pipe, 50 mm dia,medium grade as in cable protection at road crossing/wall/under floor etc including necessary cutting and making good with PCC 1:2:4, Type B-1, by using 20mm graded stone aggregate, 100mm thick or fixing on wall / poles of any type, secured with clamps, nut & bolts etc complete all as specified and as directed by the Engineer - in - Charge.

Supplying and laying GI pipe, 40 mm dia,medium grade as in cable protection at road crossing/wall/under floor etc including necessary cutting and making good with PCC 1:2:4, Type B-1, by using 20mm graded stone aggregate, 100mm thick or fixing on wall / poles of any type, secured with clamps, nut & bolts etc complete all as specified and as directed by the Engineer - in - Charge.

REKHA ELECTRICALS (BID ID -3134010)

M/s.BAJRANG CONSTRUCTION (BID ID -3130499)

UNIQUE ENGINEERS (BID ID -3137253)

Suma Construction (BID ID -3136631)

L.K.R.TIWARI CONSTRUCTION (BID ID -3136420)

M/S CHANDAN BUILDERS (BID ID -3137091)