Construction-cum-Remodeling of existing Guest House at Railhead Complex of SKUAST-Jammu

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth: consolidating each deposited layer by ramming and watering lead up to 50 m and lift upto 1.5 m

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering. All work upto plinth level.

1:3:6 (1 Cement : 3 coarse sand(zone-III) : 6 graded stone aggregate 20 mm nominal size).

1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size)

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, etc., up to floor five level, excluding the cost of centering, shuttering and finishing :

1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

1:5:10 (1 cement : 5 coarse sand : 10 graded brick aggregate 40 mm nominal size

Making plinth protection 50 mm thick of cement concrete 1: 3: 6 (1 cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) over 75 mm bed of dry brick ballast 40 mm nominal size well ramed and consolidated and grouted with fine sand including finishing the top smooth

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Providing and laying damp-proof Course 50 mm thick with cement concrete 1:2:4 (1cement:2 coarse sand: 4 graded stone aggregate 20 mm nominal size) and curing complete

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement- All work upto plinth level.

1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size).

Reinforced cement concrete work in walls (any thickness). Including attached pillasters, buttresses, plinth and string courses fillets columns, pillers, piers, abutments, posts and struts etc. upto floor 5 level exclusing cost of centring shuttering, finishing and reinforcement.

1:1.5:3 (I cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size)

Centring and shuttering including strutting, propping etc. and removal of form for

Foundations, footings, bases of columns etc. for mass concrete.

Shelves (Cast in situ).

Edges of slabs and breaks in floors and walls.

Under 20 cm wide

Columns, pillars, piers, Abutments, posts and struts

Suspended floors, roofs, landings, balconies and access platform.

Stairs, (excluding landings) except spiral-staircases.

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete up to plinth level.

Cold twisted/TMT bars

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (at all levels) in all shapes and sizes in :

Cement mortar 1: 6 (1 cement: 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (at all levels).

Cement mortar 1: 4 (1 cement: 4 coarse sand)

Steel work in built up tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Hot finished welded type tubes.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately):

Sal wood

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge.

Second class deodar wood

35 mm thick shutters

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick :

Particle Board 12 mm thick

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws.

Second Class Deodar Wood (35 mm thick)

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete :

Providing and fixing aluminium handles ISI marked (powder coated) with necessary screws etc. complete :

Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :

Providing and fixing aluminum extruded section body tubular type universal hydraulic door closer,(having brand logo with IS: 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete :

Providing and fixing aluminum hanging floor door stopper, ISI marked, anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :

Providing and fixing eye hook

Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Granite of any colour and shade

Area of slab over 0.50 sqm.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete

Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @3.3kg/sqm including pointing the joints with white cement and matching pigments etc., complete.

Providing and laying Vitrified floor tiles with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours and shades laid over 20 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement and matching pigments etc. complete.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours and shades, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement and matching pigments etc. complete

Size 600 x 600 mm

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:

(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment.

(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.

(c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge.

(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.

(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge :

With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement: 3 fine sand) as per standard design. In 75x75 mm deep chase.

Making Khurras 45x 45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20mm nominal size) over P.V.C sheet 1m x 1m x 400 micron, finished with 12mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement rounding the edges and making and finishing the outlet complete.

12 mm cement plaster of mix : Inside plaster

1:6 (1 cement: 6 fine sand)

18mm Cement plaster in two coats under layer 12mm thick cement plaster 1 : 5 (1 cement : 5 coarse sand) finished with a top layer 6mm thick cement plaster 1 : 6 (1 cement : 6 fine sand) (Outside plaster)

6 mm cement plaster of mix in ceiling:

1:3 (1 cement: 3 fine sand)

Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer

Finishing walls with Acrylic exterior paint of required shade :

New work (Two or more coat over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm).

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :

Two or more coats on new work.

Providing & laying River Bed Material (RBM) including loading, transporting, unloading, spreading, watering & ramming complete.

Providing and injecting chemical emulsion for pre/post constructional Anti-termite treatment, creating continuous chemical barrier under and around the column pits, walls, trenches, basement excavation,top surface of the plinth filling, junction of wall and floor,along the external perimeter of building,expansion joints, over the top surface of consolidated earth on which apron is to be laid, surrounding of pipe and conduits with chloropyriphos emulsifiable concentrates of 20% concentration, including cost of chemical, diluting in water to 1% concentration, labour, HOM of equipments, complete as per specifications.(plinth area of building at ground floor only shall be measured).

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank (Heavy duty)

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size),foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete

Inside size

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size),foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :

Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing following PVC pipes alongwith necessary assesories and fitting (such as tee, elbow, bends etc )complete items

PVC pipe (150 mm nominal dia)

PVC pipe (100 mm nominal dia)

Providing and fixing white vitreous china pedestal type water closet European type) with seat and lid , 10 liter low level white vitreous china flushing cistern and CP flush bend with fittings and C.I. brackets, 40mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete,including painting of fittings and brackets, cutting and making good the walls and floors wherever required

W.C. pan with ISI marked white solid plastic seat and lid included make - (jaguar , cera , hindware ) or equalent (Heavy duty one piece).

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265mm sizes respectively. included make - (jaguar , cera , hindware ) or equalent

Providing and fixing wash basin , counter top , table top with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: included make - (jaguar , cera , hindware ) or equalent

White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm C.P. brass pillar tap. included make - (jaguar , cera , hindware ) or equalent

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. included make - (jaguar , cera , hindware ) or equalent

Providing and fixing Stainless Steel A Isis 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :

Kitchen sink without drain board

610x460 mm bowl depth 200 mm.

Providing and fixing C.P. brass sink /wash basin mixer of approved quality included make - (Jaguar , cera , hindware ) or equal

15 mm nominal bore.

Providing and fixing 15 mm nominal bore C.P. brass shower rose/square approved quality conforming to IS : 8931 with 600mm shower pipe , diverter all included make - (Jaguar , cera , hindware ) or equalent

Providing and fixing 15 mm nominal bore C.P. brass long nose bib cock of approved quality conforming to IS standards included make - (Jaguar , cera , hindware ) or equalent

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing C.P. soap dish included make - (jaguar , cera , hindware ) or equal

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to European type W.C. of quality and make as approved by Engineer - in - charge included make - (jaguar , cera , hindware ) or equalent

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Flexible pipe

32 mm dia

Providing and fixing 100 mm CP grating. included make - (Jaguar , Cera , Hindware ) or equalent

Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour.

15 mm nominal bore with 45 cm length.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 included make - (jaguar , cera , hindware ) or equalent

15 mm nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. : Internal work – Exposed on wall.

15 mm dia. nominal bore

20 mm dia. nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c trenching and refilling.

25 mm dia. nominal bore

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge.

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured) for UPVC shuters.

Float glass panes ( 4 mm thick glass pane (weighing not less than 10 kg/sqm)

Providing and fixing factory made UPVC white colour sliding glazed door comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension uPVC extruded glazing beads, uPVC extruded interlock and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) cresent lock (if required), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and Drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately).

Three track three panels sliding door with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 82 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door above 2.00 sqm upto 5.00 sqm)

Providing and fixing stainless steel (SS-304 grade) friction hinges to the side/ top hung UPVC windows, of approved quality, with necessary stainless steel screws etc. as per direction of Engineer-in-charge

Providing and fixing casement handle made of zinc alloyed (white powder coated) for UPVC casement window with necessary screws etc. complete

Providing and fixing steel roller for UPVC sliding window with necessary screws etc. complete.

Providing, fixing and applying Plaster of Paris (POP) false ceiling consisting of frame work made with 50mm sq M.S. tubes of 18 G thickness as main runner at 600 mm c/c both ways, suspended/ supported with M.S. flats 25x4 mm from existing R.C.C. slab, finished smooth to line and level including necessary supports, scaffolding etc. as required and also including applying a coat of red oxide zinc chromate primer over the M.S. frame work and suspenders complete.

Including providing and fixing expanded metal of size 5.25 mm x 1.25 mm thickness welded to main runners and applying POP (calcium sulphate semi hydrate variety) to the expanded metal of thickness not less than 10 mm

Demolishing R.C.C. work manually/by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge.

Demolishing brick work manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge:

In cement mortar

Providing and fixing the following fire fighting items:-

Fire hydrant valve (63 mm) (Make: Savemax)

Short branch nozzle (63 mm)

Hose cabinet

Coupling (63 mm)

Hose reel with pipe and nozzle (25 mm)

Fire brigade connection (63 mm)

Butterfly valve (100 mm)

Non return valve (100 mm)

Foot valve (100 mm)

Ball valve (25 mm)

M.S. pipe (Make: Prakash Surya)

3 phase 10 HP motor Kirloskar/Crompton Greaves

Automatic electrical panel

Providing and fixing sheet covering over expansion joints with iron screws including cost of filling of foam in between expansion joints as per design

Aluminum fluted strip 3.15 mm thick

200 mm wide

Providing & fixing of sensor of approved and manufacture including all accessories all complete for door shutter locks

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthened clear float glass 6mm thick, spacer tube12mm wide, desiccants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in?Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.30.2) For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm.(i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.

Providing and laying 60mm thick factory made cement concrete interlocking tile made by block making machine with strong vibratory compaction and of approved size and design/shape laid in required colour and pattern over and including 50mm thick compacted bed of fine sand, filling the joints with coarse sand etc. all complete as per direction of Engineer-in-charge

Providing & fixing of 6mm HPL/ACP sheet of approved brand & make as per the architectural drawings including the cost of scaffolding and material includes all accessories.

Providing and fixing of Duct G.I.made as per the directions of the Engineer in charge

Providing and fixing 6 amps to 32 amps rating 240 volts, 'L' series, miniature circuit breaker of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as reqired (category B)

Single Pole

Triple Pole and neutral

Triple Pole

Supply and fixing of following rating, 2P 230 volts, SPN in the existing MCB DB complete with connections, testing and commissiong etc. as required

40 amps SPN

63 amps SPN

40 amps TPN

63 amps TPN

Earthing with GI earth plate 600mm x 600 mm x 6mm thick including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (with charcoal or coke and salt) complete as required for earthing and lightning protection.

Providing and fixing 25 mm x 5mm GI strip from earth electrode as required

Supply, installation, testing at works, installation and commissioning of following distribution boards totally enclosed compartmentalized, cubicle indoor type fabricated with 16 SWG sheet steel, with Aluminium bus bars (both for main and neutral bus bars), complete with following switchgear/ mountings cable terminations, inter-connections as required, for 415 volts, 3 phase, 4 wire 50 HZ AC supply as per specifications and drawings.

Moulded case circuit Breakers shall be thermal magnetic trip type. Fault level for all MCCB and bus bar shall be 35 KA. ICU shall be equal to ICS=100%

All metering current transformers shall be Class 1, 15 VA.

MDB-1 (Outdoor Type)

Incomer (Power panel)

400 A 4P MCCB – 1No.

R,Y,B phase indicating lights with control fuses - 1 set

Bus Bar

400 A 415V, 50Hz, 3ph, 4 wire Aluminium Bus bar

Outgoing

40 Amp TPN - 10 No.

63 Amp TPN - 10 No.

40 Amp SPN - 10 No.

63 Amp SPN - 10 No.

Supply, installation, testing at works, installation and commissioning of following distribution boards totally enclosed compartmentalized, cubicle indoor type fabricated with 16 SWG sheet steel, with Aluminium bus bars (both for main and neutral bus bars), complete with following switchgear/ mountings cable terminations, inter-connections as required, for 415 volts, 3 phase, 4 wire 50 HZ AC supply as per specifications and drawings.

Moulded case circuit Breakers shall be thermal magnetic trip type. Fault level for all MCCB and bus bar shall be 35 KA. ICU shall be equal to ICS=100%

All metering current transformers shall be Class 1, 15 VA.

MDB-1 (outdoor Type)

Incomer (Light panel)

250 A 4P MCCB – 1No.

R,Y,B phase indicating lights with control fuses - 1 set

Bus Bar

250A 415V, 50Hz, 3ph, 4 wire Aluminium Bus bar

Outgoing

125 Ampere MCCB 4 pole - 02 No.

40 Amp TPN - 6 No.

63 Amp TPN - 6 No.

40 Amp SPN - 6 No.

63 Amp SPN - 6 No.

Supply and laying of PVC Power cable 1.1 KV Grade armoured aluminium XLPE cables including earth work, cost of end termination, thimbles and saddles etc. as required.

3.5C x 240 sq.mm

3.5C x 150 sq.mm

3.5C x 120 sq.mm

Supply and fixing of the following way, single pole and neutral / three pole and neutral, sheet steel, double door, phase segregation type, MCB distribution board, 230V / 415V on surface/recess, complete with tinned copper bus bar, neutral bus bar and link, earth bar, din bar, detachable gland plate, interconnections, including painting, earthing, etc., as required.

8 way TPN

4 way TPN

12 way SPN

Supply and fixing 1x20 watt box type fitting complete with extruded alulminium tube rod including connection testing etc. as reqd. (CAT No. DMLNLT8-16 and LTT8-20)

Supply and fixing of 18 Watt LED Panel surface mounted including connection testing etc as reqd. (CAT No. LCDSPLN-R-18-CDL)

Supply and fixing of 18 Watt LED panel concealed including connection testing etc as reqd (CAT No. LSCRM-18-CDL)

Supply and fixing of 9 Watt LED mirror light 2' long including connection testing etc as reqd. (CAT No. LCTL-09-CDL)

Supply and fixing of 2x2 36 watt LED panel recess type including connection testing etc as reqd. (CAT No. LCTLRNE-36-FO-CDL)

Supply and fixing of 9 watt LED concealed light including connection testing etc as reqd.

Supply and fixing of LED strip complete with driver light including connection testing etc as reqd.

Supply and fixing of 70 watt LED street light with G.I. pipe bracket with all accessories including connection testing etc as reqd.

Wiring for light / fan / exhaust fan / call bell point with 1.5 Sq mm FR PVC insulated copper conductor cable in surface / recessed ISI marked PVC conduit with modular switch, modulr plate, suitable GI box and earthing the point with 1.5 sqmm FRLS PVC insulated copper conductor single core cable etc. as required.

Light point on board with copper wiring in ISI marked PVC conduit wiring for 3 Pin 6 amp plug point with 1.5sqmm PVC insulated multistrand copper conductor cable including P/F of 3 Pin 6 amp modular switch socket outlet on switch board in surfaced recessed PVC conduit wiring system and 6 amp switch, earth the 3 pin as required with 01 No. PVIC insulated green colour wire.

Wiring for light plug with 2 x 2.5sq.mm. ISI marked PVC insulated copper conductor single core cable in surface / recessed ISI marked PVC conduit along with 1x 2.5 mm copper wire for loop earthing required

Wiring for power plug with 2 x 4 sq.mm. ISI marked PVC insulated copper conductor single core cable in surface / recessed ISI marked PVC conduit along with 1x4.0 Sq mm copper wire for loop earthing as required

Wiring for power plug with 2 x 1.5sq.mm. ISI marked PVC insulated copper conductor single core cable in surface / recessed ISI marked PVC conduit along with 1x1.5 Sq mm copper wire for loop earthing as required

Wiring for 1x 1.5sq.mm. ISI marked PVC insulated copper conductor single core cable in surface / recessed ISI marked in the existing PVC conduit etc. as required ( Invertor wiring )

Wiring for sub main wiring with following sizes of PVC/ insulated copper conductor wires in the surface/ recessed PVC / MS conduit along with PVC insulated copper conductor earth wire as required complete with connections, testing and commissioning etc. as per specifications and drawings.

2x6 sq mm with 1x6.0 sqmm earth wire

4x6 sq mm with 2x6.0 sqmm earth wire

4x4 sq mm with 2x4.0 sqmm earth wire

Wiring for sub main wiring with4x10 sqmm alongwith 2x6sqmm earth wire sizes of PVC/ insulated copper conductor side core conductor in surface/recessed PVC conduit etc. as reqd.

Supplying and fixing of suitable G.I. box with modular plate and cover in the front on surface or in recessed, including providing & fixing 6 pin 15 Amp modular switch socket including connection testing etc as reqd.

Supply and fixing of 250 mm x 300 mm x 100 mm deep size metal box with suitable size phenolic laminated sheet cover in the front including connection testing etc as reqd.

Supply and fixing of two module stepped type up electronic fan regulator on the existing modular plate switch box including connecting testing etc. as required.

Supplying and fixing of exhaust fan 300mm sweep heavy duty trans air with double ball bearing including connection, testing etc. as required.

Supply and fixing Call bell / buzzer DC / AC single phase 230 V complete

Supply and fixing 20 Amp Industrial socket with 32 Amp SPN including connection, testing, etc. as required

Supply and fixing of 25 mm dia PVC conduit alongwith accessories in surface/recess.

Supply and fixing of 32 mm dia PVC conduit alongwith accessories in surface/recess.

Supply and fixing 2 Hp single phase monoblock pump set covered with shed of suitable size made of 16 SWG MS sheet including its painting and with small outdoor panel with bus bar 32 TPN with single phase starter including testing commissioning etc. required

Supply and fixing of 1200 mm sweep ceiling fan BLDC star rating inlcuding connection testing etc as reqd.

Supply and fixing of 900 mm sweep ceiling fan 1 star rating inlcuding connection testing etc as reqd.

Supply and fixing of wall fan 16" sweep including connection testing etc as reqd.

Supply and fixing of 250 KVA transformer along with GO/DO set, Fuse set, G.I. earthing (4 Nos.) including connection testing etc (LEVEL 2 Copper wounded)

Supply, installation, testing and commissioning of 01 No. Passenger Elevator (Make:- Johnson, ThyssenKrupp, Kone, Otis, Schindler, Hitachi or equivalent (The contractors are advised to quote the cost of Elevator as per the specifications in the Terms and conditions of the Contract )

M/S MAGOTRA ENGINEERS and CONTRACTOR (BID ID -2228716)

Banarsi lal and co (BID ID -2227903)

RL SHARMA (BID ID -2228595)

M/S VED PAUL DEWAN (BID ID -2227053)