EDCH-118/2022-23

Amount

Supply of Following Matarial as per relevent ISS

PCC 8.5 Mtr Long

STP Pole 13 M Long

STP Pole 11M Long

Stone pad

ACSR Dog Conductor

11 KV XLPE Cable 3x185 sqmm

3x120+1x95+1x16 sq mm AB Cable

3x50+1x35+1x16 sq mm AB Cable

LT PVC Cable AL 3.5*400 sqmm

LT PVC Cable AL 1*400 sqmm

T/F 250KVA 11/.4 Kv New

T/F 400KVA 11/.4 Kv New

11 KV V.C.B Outgoing

GI Pipe 6" Dia

HDPE Pipe Undergrouding Minimum 3 Mtr 160 mm OD PN-4PE-80 Grade U.V Stablized HDPE Pipe as IS:4984 in 6 Metre

11 Kv Cable jointing Kit

Earthing Set Complete

Stay Set Complete

11 KV V type cross Arm Complete

11 KV Pin Insulator with Pin

11 Kv Disc insulator Complete

LT Incoming Panel With Metering Equipment

F bracket

Tee Off Channal

Number Plate

Barbed Wire

Danger Board With Clamp

Guarding Angle Complete

G.I Wire 6 SWG

G.I Wire 8SWG

Suspension Clamp With I hook Complete

Dead End Clamp

3 Phase LT Distribution Box with Holding Clamp

LT Insulation Pearacing Clamp with Pearcing Conn.

Top Channal

Dropper Channal

11 Kv Fuse Set

11 KV TPMO Complete

Clamp for Top & Dropper Channal with N&B

Cross bracing M.S Angle

Clamps with Bolt & Nut

P.G Clamp

LT Piller Box

AL LUG 400 sqmm

Nut, bolt & Washer

Scope of work

Errection and grouting of following Poles including Cutting of kharanja/mettalic road/concrete portion while digging pit & complete H.T./L.T. fittings as per RESPO manual and as per direction of Engineer Incharge including the cost of labour, T&P and carrier etc. required for proper completion of work.

8.5 Mtr. long PCC Poles.

11/13 Mtr. S.T. Poles

Double pole complet fitting

Four Pole with Complete Fiting

Laying, sagging and stringing and Nozzling / binding etc. of new & old ACSR Weasal conductor / GI in 11 KV / LT lines as per RESPO manual and as per direction of supervising engineer.

ACSR Dog / Racoon Conductor

3*120+3*95 sqmm. AB Cable

3*50+1*35+1*16 sqmm AB Cable

XLPE Cable of size 3*185mmsq

LT PVC Cable AL 3.5*400 sqmm

LT PVC Cable AL 1*400 sqmm

Safe Installation of following New cousted T/F in proper alignment direction & making all HT/LT connection.

400 KVA T/F

250 KVAT/F

Fixing of HDPE Pipe Undergrounding Minimum 3 Mtr 160 mm OD PN-4PE-80 Grade U.V Stablized HDPE Pipe as IS:4984 in 6 Mtr

Fixing of GI Pipe 6" Dia

Fixing of Following Clamps for completion of work

Danger Board

Number Plate

3 Phase LT Distribution Box

11 KV Fuse Set

Fixing of 11 KV Cable Jointing Kit

Errection and grouting of stays as per RESPO Norms and as per direction of supervising engineer. Grouting material i.e. cement, sand, brick ballast/stone ballast etc. shall be arranged by the contractor at his own cost.

Fixing of earthing rod as per RESPO Norms and as per direction of supervising engineer.

Construction of plinth of size 5' * 5 * 4' above ground level one ft below the ground level of 9" After Exavation of 4 "earth brick ballast shall be provided and rammering will be done properly After ballast shall be provided and rammering will be done properly After that a retaining wall 9"width by fist class brick in ratio 1:4 of cement & sand shall be made . The earth shall be filled up to one ft.below the top of the plinth After this brick ballast shall be provided upto 6"from the earth level and proper rammering shall be done one No. jall of 12 mm MS tor shall be fixed in the hollow of plinth and one ft. thick RCC in ratio of cement sand & stone ballast shall be laid on the top of the plinth. The 12 mm thick plastering shall be done all round the plinth in 1:4 ratio of cement and sand.

Pipe earthing of 250/400 KVA medium Power Transformers

Net Fencing Shall be 1150*1200 mm made of 35*35 mm MS Angle covered by expended netal 14 SWG up to full Height 1200 mm duly steftened by MS flat by an 8 SWG dia bolt & nut

Guarding of 11 KV line by laying, stringing, sagging and binding of 2 Nos. parallel GI wire 6 SWG/ 8 SWG after providing, fabrication and fixing of guarding angle and fabrication and fixing of X-guards (Tillis) of GI wire at distance of 3 Mtr.

Fixing and grouting of LT incomming pannel with metering equipments

Safe Dismantling of following Old & Used T/F with opening of all connection with safe carriage up to JE Store/ESC Hathras (Distance Range 0 to 50 KM)

250KVA T/F

100/63KVAT/F from Double pole

Installation of extra ''T'' on the erected poles wherever required alongwith all fitting as per direction of supervising engineer including the cost of labour, T&P etc, required for proper completion of work. The "T" pole shall be grouted with cement, sand and brick ballast/stone ballast in ratio 1:4:8 including the cost of material.

Safe Dismenteling of old 5 MVA T/F from Foundation and carriage it from switch yard to out side boundary

Fixing and grouting with Earthing of 11 kv VCB Panel

Construction of Plinth Suitable for 10 MVA T/F above ground level one ft below the ground level of 9" After Exavation of 4 "earth brick ballast shall be provided and remaining will be done properly After ballast shall be provided a retaining wall 9"width by fist class brick in ratio 1:4 of cement & sand shall be made . The earth shall be filled up to one ft.below the top of the plinth After this brick ballast shall be provided upto 6"from the earth level and proper rammering shall be done one No. jall of 12 mm MS tor shall be fixed in the hollow of plinth and one ft. thick RCC in ratio of cement sand & stone ballast shall be laid on the top of the plinth. The 12 mm thick plastering shall be done all round the plinth in 1:4 ratio of cement and sand.

Making all H/T/ jumpers of installed New/Repaired 10 MVA T/f after Completion of Work

Earthing of 10 MVA power T/F (Body & Neutral)

Cutting, chopping, triming of tree branches to clear the line route to give 2 mtr. horizontal and vertical clearance to the line coming in the route of different feeders as per direction of supervising engineer

GANGA ELECTRICALS