REPAIR TO LEAKAGE/SEEPAGE ROOF TREATMENT ROOF SHEET, WATER PROOFING FLASE CEILING WALL PANELLING, FLOORING, PERIODICAL PLUMBING AND CERTAIN REPAIRS TO MD/OTM ACCN AT SAHAPORE, OD ALIPORE AND TARATALA UNDER GE (CENTRAL) KOLKATA

Amount

Demolition existing Roof Padding including Roof Treatment complete carefully by cutting, chiseling, etc. and cleaning the surfaces by scrapping, booming, bruhing, etc. and removing the rubbish from Site to a distance n exc 50.00 Metre complete all as specified and as directed.

Demolition of cement concrete (Un-reinforced) in ground floor and paving nexc 15cm thick above or below GL complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of Brick Work built in Cement Mortar including all Quoins, Arches, Pillars, etc. of any descriptions, complete all as specified and as directed.

Taking down chowkhats or frames with shutters (without taking off shutter from frames) of any sizes n exc 1.5 Sqm each complete all as specified and directed.

Taking down Chowkat or Frame with shutters (without taking off Shutter from the Frame) exc. 1.50 Sqm but not exc. 4.00 Sqm Each, complete all as specified and as directed.

Taking down Shutters of any description, exc. 1.00 Sqm but not exc 2.00 Sqm Each and keep in Safe Custody for removing to store, complete all as specified and as directed.

Dismantling Plain or Corrugated Steel Sheeting any gauge, thickness, including nainital or similar roof coverings/sunshade, complete all as specified and as directed.

Dismantling AC Corrugated Sheets as in Roofing including Ridge or Similar Pattern Roof Coverings, complete all as specified and as directed.

Dismantling of Wall and Ceiling Board (Fibre, Pulp, Insulation etc.) or Insulation Board/Slab /Blankets, any thickness including Cover Fillets, complete all as specified and as directed.

Dismantling Wrought Iron or Mild Steel Work, viz. MS Flat Iron (Wind Tie) and Similar Work including MS Bolts, Nuts, etc., complete all as specified and as directed.

Dismantling of stone slabs and tiles laid,bedded and pointed in any mortar of any description or thickness in floors, aprons etc all as directed by Engineer-in-charge.

Dismantling floors hearth or wall tilling including cement mortor bedding (but not backing) removing serviceble tiles to store and rubbish off the premises complete all as specified and directed.

Taking down cement plaster of any description on brick work or stone msonary wall including racking ot joints hacking for key scrubbing down with water etc. complete all as specified and directed.

Taking up or down Steel Water Tubing 15mm dia (bore) including Connections and Fittings, Segregating Serviceable Pipes & Fittings, Stacking properly at Site(s) and keep in Safe Custody for re-use, or removing to store, complete all as specified and as directed.

Taking up or down Steel Water Tubing 20mm dia (bore) including Connections and Fittings, Segregating Serviceable Pipes & Fittings, Stacking properly at Site(s) and keep in Safe Custody for re-use or removing to store, complete all as specified and as directed.

M&L RCC (Nominal Mix) 1:2:4 type B-1 (Using 20mm graded stone aggreagate) as in slab, shelves supported on walls beam & coloumns in floor roof including balconies, conopies, deck slabs & shelves complete all as specified and directed.

M&L Cement Concrete Type B0 (1:2:4) (12.5mm graded crushed stone aggregate) as in padding and benching and filleting complete all as specified and directed.

M&L Plain Cement Concrete type C-1, (1:3:6) (40mm graded crushed stone aggregate) as in Coping bed plate,hold fast etc,block benching,channeling slightly rounded or chamfered angle and throating including form work and finishing all exposed faces of cement concrete complete all as specified and as directed.

Cutting chases, pinning in making good to facing where required and pointing in CM 1:3 to end or edges of landing steps, cills, sunshades, shelves, lintels etc. and cutting chase for concealed water pipe etc. and making good cutting not exc 10Cm girth complete all as specified and directed.

M&L pulverized Brickwork with fly ash bricks wall have minimum compressive strength of 75 Kg/Sqcm, straight or curved on plan exc 6 m mean radius built in Cement Mortar 1:4, complete all as specified and as directed.

M&L Brick Work pulverizes fly ash bricks, Half-Brick thick have minimum compressive strength of 75 Kg/Sqcm, built in Cement Mortar 1:4, Straight or Curved on Plan to any Radius, complete all as specified and as directed.

Use and waste to Soffits of suspended slab such as Roof slab, Floor slab, landings and similar works horizontal or sloping etc., not exceding 200mm thick ,flat rough finished surfaces of concrete, complete all as specified and as directed.

S&F for 35mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides fitted to cowkhats complete all as specified and directed.

S&F 2nd class hardwood 35mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats as specified in SSR Part-I 2009 complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening with and including 3 Nos. stainless steel butt hinges 75mm long complete all as specified and directed.

S&F Factory Made Solid PVC Moulded Door Shutter With Wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm prelam PVC Sheet on back face, supplying & fixing in frame at site complete all as specified and directed.

M&L Pressed steel frames for doors with one or more rebates size of frame 125 x 60 mm including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified and directed. Note :- Pressed Steel Frame should be filled with PCC 1:3:6 Type C-0 (Using 12.50mm graded stone aggregate) and cost of PCC shall be deemed included in quoted rate

M&L Pressed steel frames for doors with one or more rebates size of frame 105 x 60 mm including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified and directed. Note :- Pressed Steel Frame should be filled with PCC 1:3:6 Type C-0 (Using 12.50mm graded stone aggregate) and cost of PCC shall be deemed included in quoted rate.

M&L 1.50mm thick power coated aluminium , three track sliding window with three nos shutters made of aluminium section as per drawing no CWE/KOL/TD-33 of section no 1F-1F including necessary jointing cleats, glazing clips, rubber neoprene packing, roller, locking arrangement, handles 2 Nos , anodised aluminium snap beading screws etc. and glazing with 4.8 mm thick tinted glass to aluminium frame work using rubber gasket where the section of frame and shutter and Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. glazing clip, fastener etc Complete all as specified and as directed. Note Nos :- (i) All window member including fitting & fixture i.e frame, track, shutter frame, etc shall be deem to included quoted rate. Only measure opening size of window.

S&F Powder coated aluminium ventilators with louvers and glazing including frame of section over all size of window 600X450mm and glazing with 4.8 mm thick tinted glass to aluminium frame work using rubber gasket where the section of frame and shutter complete with following specification . (a) Alu frames of size 45x45x1.2mm (b) Rail & Stile 45x45x1.2mm thick (c) 4.80mm thick frosted sheet glass Note :- All ventilators/louvers member including fitting & fixture shall be deem to included quoted rate. Only measure opening size of ventilators/louvers

M&L TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns,hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clip complete all as specified and directed.

S&F Roof trusses (framed) , trussed , purlines, crane gantries, rails and fastening and heavy bracket framing (Beam, tee, angle, channel or Flat section) including distance pieces , cleats etc Fe-410W (Gde E-250 Quality `A' complete all as specifed and directed.

M&L Framed Work such as Grills, Gratings, etc. with ends of Bars shouldered and/or riveted, or forged into Spikes; Framed Guard Bars; Barred Iron Doors; Ladders; Framed Balusters; Walk Ways; Railings; Framework of Water Tanks and Similar Work, conforming to Fe-290, Gde-E-165, complete all as specified and as directed.

S&F Asbestos Cement Corrugated Semi-Corrugated Sheets 6.0mm thick as in Roof Covering fixed with L–type or J–type Cranked Hook Bolts with Washers, etc. and fixed, complete all as specified and as directed.

Fixing only old serviceable Except Asbestos Cement Corrugated,Semi-Corrugated Sheets 6.0mm thickheets obtained from dismantling item as in Roof Covering fixed with L–type or J–type Cranked Hook Bolts with Washers, etc. and fixed, complete all as specified and as directed.

S&F Asbestos cement two piece adjustable plain wing ridge 6mm thick for corrugated sheet fixed with "J" &"L" type hooks complete all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated/semi corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screw complete all as specified and directed.

S&F Plain, galvanised, mild steel sheeting, class-3 thickness 0.63mm in ridges,hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 fixed with "J" &"L" type hooks complete all as specified and as directed.

S&F Solid PVC Wall Lining consisting of 5mm thick single side prelam PVC sheet inclusive of solvent cement and fixing at site on PVC frame including 5 mm thick PVC sheet fillet of width 35mm for wall Paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and as directed.

M&L False ceiling with 'E' board "Classic" , reinforced, designer series, board with HPSC of size 600 mm x 600 mm x 4 mm thick fixed on aluminium powder coated snap grid to support the boards/files with aluminium anodised main 'T' section 35mm x 23mm x 1.50mm cross tee 35mm x 23mm x 1.50mm thick and aluminium angle 25mm x 25mm x 1.40mm as on edges/sides duly suspended with 4mm dia GI hanger fixed with GI hooks 4mm dia and fastner as required at the site and applying two coats of oil bound distemper over a coat of alkali resistant primer on exposed surfaces complete all as specified and as directed.

S&F Butt Hinges extruded brass,bright polished size of Hinges 100 mm (medium weight) and fixed with brass hinge pin complete all as specified and as directed.

S&F Aluminium anodized, Barrel Tower Bolt 200mm long, Extruded Section and fixed, complete all as specified and as directed.

S&F 300mm long Aluminium alloy, anodised, Sliding Door Bolt with Hasp, Staple (Bolt type) and Fixing Clips of Sheet, Cast or Extruded Sections and Fixing Bolts and Sliding Bolts of Extruded Sections or Cast-Aluminium alloy and fixed, complete all as specified and as directed.

S&F Aluminium alloy Handle 150mm long, Extruded Section, Fabricated type, anodized and fixed, complete all as specified and as directed.

S&F Floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring (overall length of cover plate 150mm) complete all as specified and as directed.

S&F Mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete complete all as specified and as directed.

S&F Aluminium body(extruded section) door closer hydraulically regulated, designation No 2, universal type suitable for door shutters of 851 to 1000 mm in width and weight between 61 to 80 kg and fixed as in repair complete all as specified and as directed.

S&F Double action floor spring hydraulically regulated, made up of minimum 1.25mm thick aluminiun alloy sheet foundation box, main body with stainless steel cover ,governing piovet made of brass ,other parts made of mild steel heavy duty and fixed as in repair complete all as specified and as directed.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples in repair complete all as specified and directed.

M&L Water Proofing Treatment on existing cleaned RCC Roof with the following Specifications and Manufacturer's instructions, complete all as specified and as directed :- (a) Rendering 10mm thick in Cement Mortar 1:3, when concrete is steel green including WPC even and smooth and shall be cured properly for 07 Days by Ponding of water over Roof. (b) Preparing and cleaning of fully dry surface as per IS:3067-1966. (c) Applying Bitumen Primer conforming to IS-3384-1986 over the Cleaned Plastered Surface @ 0.40 Litre per Sqm. (d) Applying a layer of APP based Polymeric Membrance; modified prefabricated five layer ,3.0mm thick (minimum) weighing 3.60 Kilogram per Square Metre (reinforced) with Polyster Non Woven Fabric weighing not less than 160 Grams per Square Metre by Torch application. The overlaps shall be minimum 100mm on the Transverse direction and 75mm on Longitudinal direction. (f) Applying two coat of bitummen based UV paint with Aluminium finish @ 0.11 Litre per Sqm over APP based Polymeric Membrane.

M&L for 75mm thick PCC (1:3:6) type C-2 (Using 40mm graded stone aggregate) as in plinth protection laid in panels, finish the top surfaces even and smooth without using extra cement complete all as specified and directed Note:- Construction joints will be provided at interval of 2.5m length and filled with bitumen 80/20 mix with sand in ratio of 1:3 and cost of the same shall be deemed included in quoted rate

M&L 25mm thick PCC (1:2:4) type B-0 (using 12.5mm graded stone aggregate) as in sub base of floor complete all as specified.

M&L 100mm thick PCC (1:2:4) type B-2 (using 40mm graded stone aggregate) as in sub base of floor/path/ hard standing complete all as specified.

M&L joint free non skid ceramic coloured tiles 8-10mm thick (square/rectangular) area of each tile exc 0.06 Sqm but not exc 0.11 Sqm in floor set and jointed in in neat cement slurry and pointed in cloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed

M&L joint free non skid ceramic coloured tiles 7-8mm thick (square/rectangular) area of each tile exc 0.11 Sqm but not exc 0.18 Sqm in floor set and jointed in in neat cement slurry and pointed in cloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L joint free non skid ceramic coloured tiles 8-10mm thick (square/rectangular) area of each tile exc 0.11 Sqm but not exc 0.18 Sqm on Vertical Surfaces such as Skirting, Dados, Risers to Steps, etc., Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over and including 10mm thick backing layer in cement mortar (1:4) complete all as specified and as directed.

M&L joint free non skid ceramic coloured tiles 8-10mm thick (square/rectangular) area of each tile exc 0.18 Sqm but not exc 0.38 Sqm in floor set and jointed in in neat cement slurry and pointed in cloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed

M&L joint free non skid ceramic coloured tiles 8-10mm thick (square/rectangular) area of each tile exc 0.18 Sqm but not exc 0.38 Sqm on Vertical Surfaces such as Skirting, Dados, Risers to Steps, etc., Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over and including 10mm thick backing layer in cement mortar (1:4) complete all as specified and as directed.

M&L Heavy Duty exterior vitrified tile of Size 300x300x 7.0mm to 10.00 mm thick, as in floor, Set on Screed Bed with cement morter (1:4) jointed with Neat Cement Slurry, Pointing on Joints with Colour Pigment to match complete all as specified and as directed.

M&L Glazed Ceramic Coloured Tile 450x350x7mm thick on Vertical Surfaces such as Skirting, Dados, Risers to Steps, etc., Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over and including 10mm thick backing layer in cement mortar (1:4) complete all as specified and as directed.

M&L Granite (of any type) Work (Table rubbed and polished) 18 to 20 mm thick, in Steps, Cooking Platforms and like, Set in Screed bed of 20mm thick in Cement Mortar 1:6 including Pointing in White Cement 1:2 using Marble Dust with admixture of Pigment to match with Shade of Granite including Cutting and Polishing including half round edges, complete all as specified and as directed.

M&L Applying polymer modified cement mortar rendering 20mm thick in CM 1:3 on wall duly mixing polymer modifier "Nitobond SBR of M/s Forsoc Chemical India (Pvt) Ltd" or "Hind Styrene BR of Hindcon Chemical Ltd" or equivalent make of M/s Pidilite Industries @ 7 Litre per bag of cement complete finished even and smooth without using extra cement as per manufacturer's specification complete all as specified and directed.

Cutting out existing cracks in concrete surfaces forming grooves of 25mm x 40mm size, cleaning the groove thoroughly with blower, applying primer coat of the mix of IPH CC Resin & Hardner in equal proportion with suitable brush to form a film on the surface of groove, filling the groove with putty made by mixing IPH CC Resin, Hardner and admixture in the proportion of 1:1:4 and finally applying the sealing coat of the same mix and in the manner primer coat is applied with following min. coverage per running metre length of groove :- Material Priming Coat Putty Filling Seal Coat Resin 60 Gms 100 Gms 40 Gms Hardner 60 Gms 100 Gms 40 Gms Admixture - 400 Gms

M&L Rendering 15mm thick in Cement Mortar on other than fair faces of brick work or concrete surface of wall in two layer, first layer 10 mm thick in cement morter (1:4) and top layer 5mm thick in cement morter (1:4) using water proofing compound and finishing the surface even and smooth without using extra cement including necessary scafolding and saftey measures complete all as specified and as directed. . (NOTE:-WPC shall be measured and paid separately)

M&L rendering 15mm thick in CM (1:6) on other than fair faces of brick work or concrete surfaces even & smoth without using extra cement complete all as specified and directed.

M&L rendering 5mm thick in CM (1:3) as in ceiling surfaces even & smooth without using extra cement complete all as specified and directed.

"Supply only" liquid water proofing compound (ISI marked) complete all as specified and directed. Make:- STP NO 1/ PEDILITE(DR FIXIT)/ FOSROC/ CICO/ SIKA

M&L Preparing old decorated Plaster Surfaces of Wall and applying One Coat of White Wash (any colour/ tint) complete all as specified and as directed.

M&L Preparing new Surfaces of Walls and applying Two Coats of Distemper Oil Emulsion over a coat of primer and applied over 3mm thick water proof wall care putty including rubbing with emmery paper to make surface smooth and even complete all as specified and directed.

M&L Preparing new Surfaces of Ceiling and applying Two Coats of Distemper Oil Emulsion over a coat of primer and applied over 3mm thick water proof wall care putty including rubbing with emmery paper to make surface smooth and even complete all as specified and directed.

M&L Preparing old decorated Plaster Surfaces of Wall and applying One Coat of oil bound distemper (any colour /tint) complete all as specified and as directed.

M&L Preparing old decorated Plaster Surfaces of Ceiling and applying One Coat of oil bound distemper (any colour /tint) complete all as specified and as directed.

M&L Preparing old decorative Surfaces of walls and applying one Coat of cement base paint complete all as specified and as directed.

M&L Complete removal of old decorated surfaces and Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified & directed.

M&L Preparing newly plastered surfaces and Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified & directed.

M&L Preparing old decorated plastered surfaces of Walls and applying One Coats of Exterior Emulsion Paint Weather Coat (any colour /tint) (as per Manufacturer’s instructions), complete all as specified and as directed.

M&L Preparing old wooden Surfaces of any description not otherwise decribed over 10 Cm width or girth and applying One Coat of Synthetic Enamel Paint (First quality), complete all as specified and as directed.

M&L Preparing new wooden Surfaces of any description, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a coat of pink Primer, complete all as specified and as directed.

M&L Preparing old Steel Surfaces of any description not otherwise decribed over 10 Cm width or girth and applying One Coat of Synthetic Enamel Paint (First quality), complete all as specified and as directed.

M&L Preparing new Steel or Iron Surfaces of any description, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a coat of Red Oxide/ Zinc Chrome Primer, complete all as specified and as directed.

S&F 40mm bore MS tubing medium grade and fixed at wall for ceiling complete all as specified and directed.

S&F 20mm outer diameter CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

S&F 25mm outer diameter CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

S&F PVC (SWR) Soil, Waste and Ventilating Pipe 110mm bore (dia), single socketed, in any length with Rubber Ring Joints fixed to Walls, in repair, complete all as specified and as directed.

S&F PVC (SWR) Soil, Waste and Ventilating Pipe 110mm bore (dia), double socketed, in any length with Rubber Ring Joints fixed to Walls, in repair, complete all as specified and as directed.

S&F PVC (SWR) Bend 110mm bore (dia), any type, and Jointing with Solvent Cement, as in repair complete all as specified and as directed.

S&F PVC (SWR) Junction 110mm bore (dia), Single (Single T) equal or unequal and Jointing with Solvent Cement, as in repair complete all as specified and as directed.

S&F PVC (SWR) Nahani/Floor Trap 75mm bore (dia) Outlet, Plain with Grating and Jointing with Solvent Cement, as in repair complete all as specified and as directed.

S & F in repair for chromium plated Bib taps for 15 mm bore pipe complete all as specified and directed.

S & F in repair for brass chromium plated long body bib cock with Wall Flange for 15 mm bore pipe complete all as specified and directed.

S & F in repair for brass chromium plated two in one tap with Wall Flange screwed for 15 mm bore pipe complete all as specified and directed

S & F in repair for brass chromium plated Pillar Tap screwed for 15 mm bore pipe complete all as specified and directed

S & F work in repair for ABS body chrome plated shower rose 125mm size including fixing to steel pipe or union complete all as specified and directed

S & F in repair for shower arm 240mm long round shape with flage including fixing to steel pipe or union complete all as specified and directed

S & F in repair for 15mm bore brass chromium plated Angular Valve with Wall Flange complete all as specified and directed.

S & F in repair for 15mm bore brass chromium plated 2 way Angular Valve with Wall Flange complete all as specified and directed.

S & F in repair for ABS body chromium plated Health faucet with 8mm Dia, 1.2 Meter long flexible tube and wall hook with N.R.V (Back Flow Preventer) complete all as specified and directed.

S&F White Plastic Seat and Cover for Pedestal Pan, Closed Pattern with Recessed Bottom including Mild Steel Chromium Plated Aluminium hinging Device and fixed-in- repairs, complete all as specified and as directed.

S&F Vitreous China Wash Hand Basin 550x400mm in size, White (Flat Back or Angle Back Type) with 32mm dia Brass Chromium Plated Waste Fitting, a pair of Cast Iron Brackets duly painted including Cutting and pinning in Ends, making good disturbed Surfaces in Cement Mortar 1:3 including taking down/out unserviceable Wash Hand Basin and connected Items, complete all as specified and as directed.

S&F Vitreous China Colour Wash down Water Closet Pan (Pedestal Pattern) with "p" or "s" trap front or back inlet including fixing Bolts with and excluding 10 litre capacity low level Flushing Cistern matching with water closet colour with inlet ball valve float handle and providing 32mm dia PVC flush pipe including plastic water closet seat with flat botton cover (coloured) fixed with mild steel chromium plated or aluminium hinging device including taking down old unserviceable one complete all as specified and as directed.

S&F Vitreous China White Squatting Pan ‘ORISSA’ Pattern, size 580x440mm with ‘P’ or ‘S’ Trap, Integral Foot Rest, providing Joints between Flush Pipe and Socket of WC Pan including Flush Pipe, fixing with and including provision of cement Concrete Bedding as in repair complete all as specified and as directed.

S&F White PVC Flushing Cistern 10 Litre capacity, Low Level Valve Less, Syphonic Action type with Inlet, Ball Valve, Float and Handle including Cutting and pinning in Ends, making good disturbed Surfaces in Cement Mortar 1:3 and fixed as in repair complete all as specified and as directed.

S&F PVC Conncetions 15mm size with PTMT Nuts of length 450mm complete all as specified and as directed.

S&F Rotational Moulded Polyethylene (HDPE) Water Storage Tank 500Litre Capacity (Cylindrical Vertical with Closed Top), Black in Colour, Three Layered Construction, hoisted and fixed in Position all specified in MES Schedule Part-I including PTMT Ball Valve 15mm dia having mini -mum weight 142 Grams, high pressure with epoxy coated Aluminium Rod and high density Plastic Ball, screwed for Iron Pipe including provision of 25mm x 100mm GI nipples with check nuts for inlet, outlet wash and overflow pipe including Lowering of old/unserviceable Water Storage Tank of any description, complete all as specified and as directed.

S&F Rotational Moulded Polyethylene (HDPE) Water Storage Tank 1000Litre Capacity (Cylindrical Vertical with Closed Top), Black in Colour, Three Layered Construction, hoisted and fixed in Position all specified in MES Schedule Part-I including PTMT Ball Valve 15mm dia having mini -mum weight 142 Grams, high pressure with epoxy coated Aluminium Rod and high density Plastic Ball, screwed for Iron Pipe including provision of 25mm x 100mm GI nipples with check nuts for inlet, outlet wash and overflow pipe including Lowering of old/unserviceable Water Storage Tank of any description, complete all as specified and as directed.

S&F Rotational Moulded Polyethylene (HDPE) Water Storage Tank 2000Litre Capacity (Cylindrical Vertical with Closed Top), Black in Colour, Three Layered Construction, hoisted and fixed in Position all specified in MES Schedule Part-I including PTMT Ball Valve 15mm dia having mini -mum weight 142 Grams, high pressure with epoxy coated Aluminium Rod and high density Plastic Ball, screwed for Iron Pipe including provision of 25mm x 100mm GI nipples with check nuts for inlet, outlet wash and overflow pipe including Lowering of old/unserviceable Water Storage Tank of any description, complete all as specified and as directed.

UNIVERSAL TRADING CENTRE (BID ID -3234538)

K.P Construction Co (BID ID -3235591)