Construction of 2nd Floor of Ujala Girls Hostel for PG students alongwith internal electrification and sanitary fittings at Main Campus Chatha

Amount

Earthwork in excavation by mechanical means (Hydraulic excavator)/manual means in foundation trenches or drains ( not exceeding 1.5 m in width or 10 Sq. m on plan), including dressing of sides & remaining of bottoms , lift upto 1.5 m , including getting out the excavated soil and disposal of surplus excavated soil as directed , within a lead of 50 m

All kinds of soil.

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering. All work upto plinth level.

1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size)

1:3:6 (1 Cement : 3 coarse sand(zone-III) : 6 graded stone aggregate 20 mm nominal size).

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level

1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness). Including attached pillasters, buttresses, plinth and string courses fillets columns, pillers, piers, abutments, posts and struts etc. upto floor 5 level exclusing cost of centring shuttering, finishing and reinforcement.

1:1.5:3 (I cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size)

Centring and shuttering including strutting, propping etc. and removal of form for

Foundations, footings, bases of columns etc. for mass concrete.

Suspended floors, roofs, landings, balconies and access platform.

Lintels, beams, plinth beams, girders, bresumers and cantilevers.

Columns, pillars, piers, Abutments, posts and struts

Edges of slabs and breaks in floors and walls.

Under 20 cm wide

Reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete

Cold twisted bars/ mild steel and MT steel

Add for plaster drip course/grooves in plastered surface or moulding to R.C.C. projections

Brick work with common burnt clay F.P.S. (non-modular) bricks of class designation 7.5 in superstructure above plinth level upto floor V level in all shapes and sizex:

Cement mortar 1:6 ( 1 cement : 6 coarse sand)

Half brick masonry with common burnt clay FPS (non-modular) bricks of class designation 7.5 in superstructure above plinth level upto floor V level

Cement mortar 1: 4 (1 cement: 4 coarse sand)

Extra for providing and placing 2 Nos. 6 mm dia M.S. bars at every third course of half brick masonry (with FPS bricks)

Marble work gang saw cut (polished and machine cut) of thickness 18mm for wall lining (veneer work), backing filled with a grout of average 12 mm thick in cement mortar 1:3 (1 cement : 3 coarse sand) including pointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with an admixture of pigment to match the marble shade: (To be secured to the backing by means of cramps, which shall be paid for separately).

Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble.

Area of slab upto 0.50 sqm

Providing and fixing 18 mm thick gang saw cut, mirror polished, pre moulded and prepolished machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size of approved shade, colour and texture laid over 20 mm thick base cement mortar 1: 4 (1cement: 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edge to give high gloss finish etc. Complete at all levels.

Granite of any color and shade (Area of slab over 0.5 sqm)

Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete:

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete :

Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :

Steel work welded in built up sections / framed work including cutting hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc as required.

In grating, frames, guard bar, ladders, railings,brackets, gates and similar works

Providing and fixing hand rail by welding etc. to steel lader railing , balcony railing and staircase railing including applying a priming coat of approved steel primer

MS tube (Medium) 40 mm nominal bore

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.

40 mm thick with 20 mm nominal size stone aggregate

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :

25 mm thick.

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing and fixing 1st quality ceramic glazed tiles conforming to IS: 13753 of minimum thickness 5 mm of approved make like NITCO, ORIENT, SOMANY KAJARIA, or equivalent make in all colours, shades except begundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1: 3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3 KG per sqm including pointing in white cement mixed with pigment of matching pigment etc., complete. (wall tile)

Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc.,., complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08%and conforming to IS : 15622 , of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete.

Size of Tile 600x600 mm

12 mm cement plaster of mix :

1:6 (1 cement: 6 coarse sand)

15mm cement plaster on rough side of single or half brick wall of mix

1:6 (1 cement :6 coarse sand)

6 mm cement plaster to ceiling of mix

1: 3 (1 cement: 3 fine sand)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade.

New work (two or more coats) over and including water thinnable priming coat with cement primer.

Finishing walls with acrylic smooth exterior paint of required shade on New work (Two or more coats applied @ 1.67 liter/10sqm over and including priming coat of exterior primer applied @ 2.20kg/10sqm)

Applying priming coat:

With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :

Two or more coats on new work.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Finishing walls with Acrylic smooth exterior paint of required shade:

Old work (two or more coats applied @ 1.67 liters/10sqm on existing cement paint surface)

Demolishing cement concrete manually/by mechanical means including disposal of material within 50 meters lead as per direction of Engineer-in charge:

Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Demolishing brick work manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge:

In cement mortar

Providing and fixing water closet squatting pan (Indian type W.C pan) with 100mm sand cast iron P or S trap, 10 litre low level white P.V.c flusing cistern with manually controlled device (handle level) conforming to IS : 7231, Parryware/ Hindware / Seabird/ Orient (coral) with all fittings and fixtures complete including cutting and making good the walls and floors wherever required

White vitreous china Orissa pattern W.C pan of size 580x440mm with integral type foot rests.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :

W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing Stainless Steel A Isis 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :

510x1040 mm bowl depth 200 mm.

Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings :

Flat back wash basin of size 550x400 mm.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Semi rigid pipe

32 mm dia

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminum angle frame with CP brass brackets and guard rail complete fixed with 40mm long screws, rawl pluggs etc. complete

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with a minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe including painting with anticorrosive bitumastic paint, cutting chases and making good the wall:

15 mm dia. nominal bore

20 mm dia. nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. : External work

25 mm dia. nominal bore

32 mm dia. nominal bore

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For fixed portion

Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately).

Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer?in-charge. (Cost of aluminum snap beading shall be paid in basic item.)

With float glass panes of 4.0 mm thickness

Providing and fixing 100 mm Brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

Providing and fixing Stainless Steel (SS 304 grade) adjustable friction windows stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per the directions of the Engineer in charge.

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying:

(a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm.

(b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm.

(c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around.

(d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately) For the purpose of measurement the entire treated surface will be measured.

Providing and fixing aluminium partitioning with ACP sheet of nominal thickness.

Providing and fixing 35 mm thick wire guage shutters using galvanised MS wire guage of average width of aperture 1.4mm with wire of dia 0.63 mm for doors including ISI marked bring finished or / and black enamelled M.S.butt hinges with necessary screws and polishing the shutter complete.

second class Deodar wood

Providing and fixing wire gauge in aluminium shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire gauge of dia 0.63 mm in doors/windows.

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering (1:5:10) mix conc. Using brick aggregate of size 40 mm complete (for flooring)

Providing and fixing 12 mm thick board (Decorative type) to the aluminium partitioning.

Providing and fixing interlocking arrangements/system in sliding aluminium windows complete.

Providing and fixing of the following sanitary items with necessary fittings complete item

Soap dish of nominal size (CP)

PVC connection

CP gratings (100 mm)

CP long body bib cok of approved make (15 mm nominal bore)

CP short body bib cok of approved quality (15 mm nominal bore)

C.I. waste coupling 30 mm of 79 mm length x 77 mm breadth

Providing & fixing of shower of nominal dia and approved make.

Providing and fixing of the following G.I. accessories/fittings and making G.I. connection with manholes.

Ball valve of nominal dia (20 mm)

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement: 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size),inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete.

900 mm x 750 mm

Small size=300 mm x 300 mm

Providing and fixing:-

PVC Pipe (150 mm dia)

PVC pipe (110 mm nominal dia)

PVC pipe (75 mm nominal dia)

PVC plain bend (110 mm)

PVC plain bend (75 mm)

Door bend (110 mm)

Door bend (75 mm)

Providing and fixing in position PVC water tank of Sintex or Equivalent brand with lockable cover including connection of inlet-outlet over flow and cleaning pipes including cost of GI pipe , G.I fittings complete item of nominal capacity

Providing and fixing of the following accessories including necessary nails and screws complete

Aluminum alloy Handles

Aluminum Tower bolts

Aluminum Arle

Door stopper

Door closer

Providing and fixing the following fire fighting items:-

Butterfly valve 1"

Non return valve 1"

Branch pipe with nozzle 1"

Fire brigade connection

Fire rated door complete accessories and fire rated 120 m

Hase real drum and accessories

Landing valve

Coupling M/F

Union 3"

Reel hose pipe

Cabinet

Socket 3"

M.S. pipe :-

Supplying and laying of 35 x 3.5 core aluminium armoured PVC cable

M.S. flange

ABC type fire extinguishers 6 Kg

CO2 Type fire extinguisher 2 Kg

5 HP motor Kirloskar/Crompton Greaves

SUB-DISTRIBUTION BOARDS

Providing and fixing 6 amps to 32 amps rating 240 volts, 'L' series, miniature circuit breaker of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as reqired (category B)

Single Pole - 6 to 32 A

Supply and fixing of following rating, 2P 230 volts, SPN in the existing MCB DB complete with connections, testing and commissiong etc. as required

40 amps SPN

63 amps SPN

40 amps TPN

63 amps TPN

EARTHING AND LIGHTNING PROTECTION

Earthing with GI earth plate 600mm x 600 mm x 6mm thick including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (with charcoal or coke and salt) complete as required for earthing and lightning protection.

Providing and fixing 25 mm x 5mm GI strip from earth electrode as required

LT CABLES

Supply and laying of PVC Power cable 1.1 KV Grade armoured aluminium XLPE cables including earth work, cost of end termination, thimbles and saddles etc. as required.

3.5C x 185 sq.mm

3.5C x 120 sq.mm

SUB-DISTRIBUTION BOARDS

Supply and fixing of the following way, single pole and neutral / three pole and neutral, sheet steel, double door, phase segregation type, MCB distribution board, 230V / 415V on surface/recess, complete with tinned copper bus bar, neutral bus bar and link, earth bar, din bar, detachable gland plate, interconnections, including painting, earthing, etc. as required.

8 way TPN

4 way TPN

12 way SPN

Supply and fixing 1x20 watt box type fitting complete with extruded alulminium tube rod including connection testing etc. as reqd. (CAT No. DMLNLT8-16 and LTT8-20)

Supply and fixing 2x20 watt box type fitting complete with extruded alulminium tube rod including connection testing etc. as reqd. (CAT No. IGP-132-LT-8-16)

Supply and fixing of 9 Watt LED mirror light 2' long including connection testing etc as reqd. (CAT No. LCTL-09-CDL)

Supply and fixing of 72 Watt LED street light with GI pipe bracket with all accessories including connection testing. (CAT No. LSTP-72-CDL)

Supplying and fixing of batton holder with 7 W LED bulb including connection testing etc as reqd

Wiring for telephone point with 0.61 mm dia copper conductor unarmoured shielded twisted telephone wire in 25mm dia existing PVC conduit, connections etc. complete as required as per specification and drawings.

Supply and fixing telephone socket outlet housed in zinc passivated box with suitable connector strip in recessed wall / partitions as required (piano type)

Supply and fixing of following switch/socket on the modular plate and switch box including connection testing etc as reqd.

TV antenna socket outlet.

R-J-45 moudlar socket.

WIRING

Wiring for light / fan / exhaust fan / call bell point with 1.5 Sq mm FR PVC insulated copper conductor cable in surface / recessed ISI marked PVC conduit(2mm thick) and providing 5 Amp switch (Piano type) and earthing the point with 1.5 sqmm FRLSPVC insultated copper conductor single core cable etc as reqd.

Light point on board with copper wiring in ISI marked PVC conduit wiring for 3 Pin 6 amp plug point with 1.5sqmm PVC insulated multistrand copper conductor cable including P/F of 3 Pin 6 amp socket outlet on switch board in surfaced recessed PVC conduit wiring system and 6 amp switch, earth the 3 pin as required with 01 No. PVIC insulated green colour wire.

Wiring for light plug with 2 x 2.5sq.mm. ISI marked PVC insulated copper conductor single core cable in surface / recessed ISI marked PVC conduit along with 1x 2.5 mm copper wire for loop earthing required

Wiring for power plug with 2 x 4 sq.mm. ISI marked PVC insulated copper conductor single core cable in surface / recessed ISI marked PVC conduit along with 1x2.5 Sq mm copper wire for loop earthing as required

Wiring for power plug with 2 x 1.5sq.mm. ISI marked PVC insulated copper conductor single core cable in surface / recessed ISI marked PVC conduit along with 1x1.5 Sq mm copper wire for loop earthing as required

Wiring for 1x 1.5 sq.mm. ISI marked PVC insulated copper conductor single core cable in surface / recessed ISI marked in the existing PVC conduit etc. as required ( Invertor wiring )

Wiring for sub main wiring with following sizes of PVC/ insulated copper conductor wires in the surface/ recessed PVC / MS conduit along with PVC insulated copper conductor earth wire as required complete with connections, testing and commissioning etc. as per specifications and drawings.

2x6 sq mm with 1x6.0 sqmm earth wire

4x4 sq mm with 2x4.0 sqmm earth wire

2x10 sq. mm with 1 x 6.0 sq. mm earth wire

4x10 sq mm with 2x6.0 sqmm earth wire

Wiring for sub main wiring with 4x6 sqmm alongwith 2x6sqmm earth wire sizes of PVC/ insulated copper conductor side core in surface/recessed PVC conduit etc. as reqd.

Wiring for twin control light point with 2x1.5 sq. mm PVC insulated copper conductor cable in surface / recessed ISI marked PVC conduit with 2 way 6 Amp switch modular type

Supplying and fixing metal box of 180 x 100 x60mm deep in recessed with suitable size phoenolic laminated sheet cover in the front including providing and fixing 3 pin 15Amp modular socket outlet and 15Amp modular switch connections, painting etc. as required. (Power plug)

Supply and fixing of 250 mm x 300 mm x 100 mm deep size metal box with suitable size phenolic laminated sheet cover in the front including connection testing etc as reqd.

Supply and fixing of 200 mm x 300 mm x 100 mm deep size metal box with suitable size phenolic laminated sheet cover in the front including connection testing etc as reqd.

Supply and fixing step up electronic fan regulator on the existing switch box including connecting testing etc. as required.

Supply and fixing of Ceiling fan 1200 mm sweep 5 star rating including connection testing etc as reqd.

Supply & fixing of 10 sqmm x 2 core aluminium armoured PVC cable suitable for 1.1 KV grade including cost of end termination, connection testing etc. as reqd.

Supply and fixing of wall bracket suitable for 230 volts complete with 15 watt LED including connection testing etc as reqd.

Supplying and fixing of exhaust fan heavy duty trans air with double ball bearing of following sizes including connection, texting etc. as required.

12" exhaust fan

Supply and fixing Call bell / buzzer DC / AC single phase 230 V complete

Supply and fixing of 20 Amp industrial socket for Air-conditioner with 32 Amp SPN including connection, testing, etc. as required

Supply and fixing 2 Hp single phase monoblock pump set covered with shed of suitable size made of 16 SWG MS sheet including its painting and with small outdoor panel with bus bar 32 TPN with single phase starter including testing commissioning etc. required

Supply and fixing of 25 mm dia PVC conduit alongwith accessories in surface/recess.

Supply and fixing of 32 mm dia PVC conduit alongwith accessories in surface/recess.

Supply and drawing of co-axial TV cable RG-6 grade, 0.7mm solid copper conductor PE insulated , shielded with fine tin copper braid and protected with PVC sheath in the existing / recessed PVC conduit

Supply and fixing of CAT-6 wire in the existing PVC conduit including connection testing etc. as reqd.

Erection of SST poles in cement concrete pedestal 1:3:6 including excavation foundation (1:4:8) centering and shuttering of poles by engaging skilled labour with long rope complete job including cost of cement and carriage of pole from store to site.

Supplying and fixing of Mukki Clamp complete with nut, bolt etc. as reqd.

Supplying and fixing of U-Clamp alongwith 4" in size Shekel insulator with 6" long G.I. nut bolt complete job.

Supplying, laying, stringing and binding of LT conductor (Rabbit)

Supplying, laying, stringing and binding of LT conductor (weasel)

Supplying and fixing of stray rod complete with all accessories including digging of pit and refilling it with cement concrete (1:3:6) complete job including cost of cement.

Stringing and binding of existing LT conductor including dismantling of existing conductor and binding it after compelte item.

MOHD IDRIS SHAN (BID ID -2397324)

Banarsi lal and co (BID ID -2398205)

I MB CC PRIVATE LIMITED (BID ID -2397750)