Construction of additional building to Government Hospital at Ambasamudram in Tirunelveli District

Amount

Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Refilling with excavated earth other than Crushed Stone M-Sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officers in layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification

Supplying and filling the foundation and Basement with Conveyed Earth with in 5 kmmr in layers of not more than 15cm.thick well rammed, watered and consolidated with complete complying with Standard specification.

Supplying and filling in foundation, basement, etc with filling Crushed Stone M-Sand in layers of not more than 15 cm thick Without consolidation etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and filling the foundation and Basement with filling Stone dust in layers of not more than 15cm.thick well rammed, watered and consolidated with complete complying with Standard specification.

Cement Concrete 1:5:10 (One Cement, Five Crushed Stone M-Sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification

Brick work in following Cement Mortar 1:3 (One Cement, Three Crushed stone M-Sand) using best quality of country bricks of size 8-3/4" x 4-1/4" x 2-3/4" for foundation and basement including curing, etc., complete complying with standard specifiction.

In Foundation and Basement.

In Ground floor

Brick work in Cement Mortar 1:5(One Cement, Five Crushed Stone M-Sand) using best quality of country bricks of size 8-3/4" x 4-1/4" x 2-3/4" for foundation and basement including curing, etc., complete complying with standard specifiction.

For Foundation and Basement.

Brick work in Cement Mortar 1:6(One Cement, Six Crushed Stone M-Sand) using best quality of country bricks of size 8-3/4" x 4-1/4" x 2-3/4" for foundation and basement including curing, etc., complete complying with standard specifiction.

In Ground floor

In First floor

In Second floor

In Third Floor

Supplying and erecting steel Shuttering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete

For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.

For plane surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall, etc.

For Circular Column

For Curved surface

Providing and laying in position, standardised concrete Mix M-20 Grade in accordance using 20mm with IS:456-2000, and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 350 kglms and maximum water cement ratio of 0.50, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concreteimprove workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3'3 cu'm') 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu'm') 7670 kg' of Crushed Stone M-Sand,

but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

For Foundation and Basement.

In Ground floor.

In first floor.

In second floor.

In Third floor.

Providing and laying in position, standardised concrete Mix M-25 Grade in accordance using 20mm with IS:456-2000, and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 350 kglms and maximum water cement ratio of 0.50, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 k9. of 20mm machine crushed stone jelly and with about (3'3 cu'm') 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu'm') 7670 kg' of Crushed Stone M-Sand

but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials)

For Foundation and Basement.

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Cement Concrete 1:5:10 (One cement, Five Crushed Stone M-Sand and Ten hard broken stone) using 40 mm gauge hard broken jelly for flooring including laying, consolidating, finishing, rendering the top surface rough to receive the floor, curing, etc. complete complying with standard specification and as directed by the Departmental Officers.

Brick partition walls of 10.80cm thickness using best quality country bricks of size 8-3/4" x 4-1/4" x 2-3/4" in Cement Mortar 1:3 (One Cement and Three Crushed Stone M-Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

In Ground floor

In First Floor.

In Second floor

Paving the floor with best quality Double charged Vitrified Tiles(Marbonite) of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three Crushed Stone M-Sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with pre-polished concrete Anti-skid step tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three Crushed Stone M-Sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with Cement based Hydraulically pressed Anti skid tiles (pattern design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three Crushed Stone M-Sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Flooring with anti skid designed colour Ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three Crushed Stone M-Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with best approved quality fine polished Granite Stone Slabs of size 1200 x 600 of 18 / 20mm thick of Synthetic Grey, Paradise and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three Crushed Stone M-Sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Supplying and laying of factory made Tamin interlocking Paver Blocks of 63 mm thick, the cost includes base cushion of 10cm depth transporting charges etc., complete complying with standard specification.

Dadooing walls with colour designed digital printed ceramic tiles of size 300mm x 450mm x 8mm and above in best approved quality tiles set in Cement Mortar 1:2 (One Cement and Two Crushed Stone M-Sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification ( Non branded) and as directed by the departmental officers.etc., (The make and brand of the tiles should be Johnson/kajaria/somani/mitco/RAK (or) equalent which as to be got approved by Executive Engineer before use on works).

Plain Cement Concrete 1:2:4 (one cement, two Crushed Stone M-Sand and four hard broken stone jelly) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers.

In Ground Floor

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no Crushed Stone M-Sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Crushed stone Crushed Stone M-Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Supplying and fixing fine polished cuddapah slab of following thickness for cup-board arrangements including laying to correct alignment with necessary cement mortar and black powder etc, complete complying with standard specification and as directed by the Departmental Officers.

Cuddapah Slab 20/30mm thick

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc.

110mm dia PVC Pipe

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers (with bonding agent cebex-112, zydex-zycrete 2X or other equivalent compound)

Plastering with Cement Mortar 1:5 (One cement and Five Plastering Sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.(with bonding agent cebex-112, zydex-zycrete 2X or other equivalent compound)

Plastering with Cement Mortar 1:3 (One cement and Three Plastering Sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.(with bonding agent cebex-112, zydex-zycrete 2X or other equivalent compound)

Damp proof course with Cement Mortar 1:4 (One Cement and Four Plastering Sand) 12mm thick mixed with best approved quality water proofing compound conforming to Indian Standard specification as specified by the departmental officers at 2% by weight of cement used, finishing and curing etc. complete complying with standard specification.

Painting two coats of newly plastered wall surface with ready mixed plastic Interior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification and as directed by the departmental Officers.

Painting two coats of newly plastered wall surface with ready mixed plastic Exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification and as directed by the departmental Officers.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Painting new wood work with two finishing coats of synthetic enamel ready mixed paint of approved quality and colour over one coat priming coat in all floors including the cost of primer etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Fabricating Supplying and fixing in position of Aluminium anodised Powder Coated of single leaf door with half panelled with 12mm thick both side laminated particle board at bottom and half glazed using 5.50mm thick Plain glass at top.The outer frame shall be with aluminium box section 101.60x44.45x3.18m at 2.319kg/m and Shutter frame made of section Vertical & Top rail: [email protected] kg/m and Bottom rail: 100x44.45x2.50mm@ 1.974 kg/m, Lock rail : 50x44.45x2.5mm @ 1.292 kg/m,Alu. Clips: 17.15x17.27x1.50mm @ 0.176 kg/m,Alu. Handle: 100x30mm @ 0.988 kg/m and necessary accessories such as aluminium clips, rubber beading, PVC felt, handle for a length of shutter (both sides), locking arrangements, furniture fittings such as aluminium tower bolts-250x12mm - 1 Nos., aluminium tower bolt 200x12mm - 1No., aluminium Hydraulic door closer - 1No ., lock-1No., Door stopper with rubber bush

including cost of materials labour charges and power consumption charges required for fabrication including chipping, dismantling and making hole to the required extent in RCC column, beams, masonry with power drill wherever necessary and redoing the damaged portion to the original condition after fixing etc., complete. All the Alu. Section are to be anodised with matt finish under electricaly controlled conditions in accordance with IS 1868/1962 for an average anatic film thickness of 15 microns etc., complete.Aluminium sections,and furniture fittings shall be got approved by the Executive Engineer incharge. Door size 1.00m X 2.10m-With Automatic Door closure and Hinges

Supplying, fabricating and fixing in position of Aluminium anodised Powder Coated of double leaves door with half panelled with 12mm thick bothside prelaminated partile board at bottom and half glazed using 5.50mm thick Plain glass at top. The outer frame shall be with aluminium box section 101.60x44.45x3.18m at 2.319kg/m and Shutter frame made of section with Vertical & Top rail: [email protected] kg/m Bottom rail: 100x44.45x2.50mm@ 1.974 kg/mLocal rail : 50x44.45x2.5mm @ 1.292 kg/mAlu. Clips: 17.15x17.27x1.50mm @ 0.176 kg/mAlu. Handle: 100x30mm @ 0.988 kg/m the and necessary accessories such as aluminium clips, rubber beading, PVC felt, handle for a length of shutter (both sides), locking arrangements, furniture fittings such as aluminium tower bolts-250x12mm - 2 Nos., aluminium tower bolt 200x12mm - 1No., aluminium Hydraulic door closer - 2Nos ., lock-1No., Door stopper with rubber bush

including cost of materials, labour charges and power consumption charges required for fabrication including chipping, dismantling and making hole to the required extent in RCC column, beam masonry with power drill wherever necessary and redoing the damaged portion to the original condition after fixing etc. complete.All the Alu. Section are to be anodised with matt finish under electricaly controlled condition in accordance with IS 1868/1962 for an average anodic film thickness of 15 microns etc., complete.Aluminium sections,and furniture fittings shall be got approved by the Executive Engineer incharge. Door size 1.20 x 2.10mWith Automatic Door closure and Hinges

Supplying, fabricating and fixing in position of Aluminium Powder Coated of single leaf fully panelled sliding door with 12mm thick bothside prelaminated partile board at the Shutter bottom rail:[email protected] kg/m,Top & Verticle 50x44.45x2.50mm @ 1.292 kg/m,Lock rail 50x44.45x2.50mm @ 1.292 g/m, Running channel section:[email protected] kg/m, and necessary accessories such as Alu.clips 17.15x17.27x1.50mm @ 0.176 kg, Alu handle 100x30mm @ 0.988 kg/mfull length of handles on both sides, lock, roller, including cost of materials, labour charges and power consumption charges required for fabrication including chipping, dismantling and waking hole to the required extent in RCC column, beam masonry with power drill wherever necessary and redoing the damaged portion to the original condition afterfixing etc. complete. All the Alu. sections are to be anodised. with matt finish under electically contolled condition in accordance with IS 1868/1962 for an average anodic film thickness of 15 microns etc., complete. door size 1.00 x 2.10m

Solid PVC door shutters using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm, with suitable rabate for housing the shutter.(solid panel PVC door with frame)

Supplying and fixing in postion of Aluminium anodised natural colour matt finish Openable Cupboard of size 1.20x2.10 m in all floors fixed with 12 mm thick Prelaminated particle board (Exterior grade ). the outer frame of section 38x33x2.12 mm @ 0.706 kg/m, shutter frame of 38.5x33x3 mm @ 0.706 kg/m, Interlocking mullion vertical section of 59x33x2.5 mm @ 1.135 kg/m. The shutter is fixed with 6 nos. Aluminium hinges, 100x30 mmof 2 nos. D Type handle 100 mm long and 2 nos. of Cupboard lock etc. with necessary furniture fittings including cost of, labours, power consumption charges required for fabrication including necessary chipping, dismatling and making necessary holes in the RCC columns beams, masonry etc., with power drill to the required depth and redoing the same to the original condition after fixing etc., complete. complying with standard specification.

Fabricating Supplying and fixing inposition Aluminium anodised natural colour matt finish Two track sliding hatch window in all floors with Alu. Section of Outer Vertical frame : 62x31.50x1.50mm @0.875 kg/m,Outer top & bottom gutter frame: 61.98 x 39.30 x 1.50mm @ 0.778kg/m,shutter vertical: 36.60x18x1.50mm@ 0.439kg/m, Shutter horizontal: [email protected]/m with necessary accessories such as Lock, handle, wheel arrangements including supplying and fixing 8mm thick both side prelaminated partical board including cost of all materials, labours, power consumption required for fabrication, drilling holes in RCC column slab, masonry walls wherever necessary with power drills to the required extent and make good to the original condition after fixing and also as directed. All the Aluminium sections are to be anodised with matt finishunder electrically controlled condtions in accordancewith IS 1868/1962 for an average anodic film thickness of 15 microns etc. complete. Size 0.90 x 0.70m

Supplying and fixing UPVC (Un Plasticized polyvinyl chloride) Windows of casement type (open) from the profile the size of outer frame 60mmx58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of ESpage multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakages of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The Connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing. The window should be got approved from the executive engineer use on work

Supplying and fixing UPVC (Un plasticized Polyvinyl chloride) Louvered Ventilator of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 78 mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all around the frames. The Ventilators should be got approved from the executive engineer before use on work.

Supplying, fabricating and fixing in position Aluminium Natural Colour matt finish Fixed glazing . The glass used shall be of 5 mm thick The outer frames shall be with aluminium box section 101.60 x 44.45 x 3.18m at 2.319 kg/m The aluminium section are to be anodised under electrically controlled conditions as per IS 1868/1962 for an anodic film thickness of 15 microns. All the materials should be go approved by the executive Engineer before execution of works. All the materials should be got approved by got approved by the Executive Engineer before execution of works.size 1.50 x 2.10m

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat Crushed Stone M-Sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door

Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door.A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete. Single leaf 1.00 x 2.10m

Manufacturing, supplying and fixing of steel doors with the following specification M.S angles of a size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32x6mm M.S. flat is provided at required intervals in the shutter frames 18 gauge C.R. sheet is laid as panel in the shutter and welded intact for 1/3 bottom portion of the shutter. M.S. flat 18x5mm is welded over the 32x6mm M.S. flat Crushed Stone M-Sand witching the CR sheet in between. Additional stiffener with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter. The balance 2/3 portion at top is provided with grill at an average weight of 20kg/sq.m and 6 Nos hinges for double leaves shutter to be provided 6nos of holdfasts 120mm in length made of angle section spliced at the ends are welded to the outer frame of the door.

Tower bolts 2nos. one at top and the other at the bottom arte provided one aldrop is provided at on appropriate place in the door. A Tie bar is provided at the bottom of the outer frame to prevent twisting of frame during transportation or fixing. All members are given one coat of red oxide primer as directed by the departmental officers. The rate includes cost of all meterials, labour charges,taxes, transportation to site of work , loading, unloading and all other incidental charges etc.,complete. Double leaves 1.50 x 2.10m

Fabricating Supplying and fixing in position of Aluminium anodised natural colour matt finish 1/3rd fixed glazing 2/3rd prelaminated board of Aluminium partition. The outer frames Outer frame: 63.50x38x3mm@ 1.72 kg/m,Centre mullions: 63.50x38x3mm@ 1.55 kg/m,Alu. Clips: 17.27x17.15x1.50mm @ 0.175kg/mg/m for intermediate vertical mullion 90cm c/c. Horizontal mullion at 1.00m 2.10m covered with 5.5mm thick plain glass with neccessary aluminium clips of size 17.27x17.15 x1.50mm @ 0.176kg/m and with required rubber beading etc., including necessary dismantling holes in RCC column,masonry wherever in necessary with power drills to the extent required and made good the damaged portion in good condition after fixing as directed by the departmental officers. All the aluminium sections should be anodised not less than 15 microns as ISI specification1868/1962 / and should be gotapproved by Executive Engineer before use, (SIZE : 2.70 x 2.10m)

Manufacturing supplying and fixing in position of RCC jally of 5cm thickness in cement concrete 1:2:4 using 20mm crushed stone jelly(excluding cost of reinforcement steel) includes cost of mould,finishing,curing,lifting,fiximg in position etc, complete complying with standard specification and as directed by the departmental officers in all floors.

Suplying and fixing M.S Grill for Window & ventilators, grill gates etc including cost of materials and labour charges for cutting to required sizes,fabricating, welding and transporting at site of work and including the cost of one coat red oxide primer etc., complte complying as directed by the departmental officers.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900 mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase near wet riser using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick will be provided with tubular supports made of 304L Grade Stainless Steel pipe of 25mm dia of 1.60mm thick welded to the railing. The supports will be grouted into the wall and provided with 93.00mm thick Stainless Steel circular base plate of 304 Grade. The rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing, bonding, cutting, grinding, conveyance, welding charges, electrical charges, etc. complete

Supplying and fixing in position CI manhole covers with CI frames (Heavy duty) of size 60cm x 60cm of best approved quality as per standard specification etc., complete compying with standard specifications

Providing and fixing GYP BOARD FALSE CEILING and fixing with new Gyp Board false ceiling which includes ‘V’ shaped GI channels of size 25 mm x 25 mm x0.5 mm thick suspended from ceiling at 1.20 m both longitudinal and cross vertical support and fixing’ U’ shaped G I channels of size 50 mm x 30 x 0.50 mm and 150 mm x10 mmx 0.5 mm thick at 0.60 metres center to center and cross direction and at 1.20m center to center longitudinal and cross direction for vertical supports and fixing ‘U’ shaped G I channels of size 50 mm x 30 mm x 0.50 mm thick and 50 mm x 10 mm x 0.50 mm thick at 0.60 m center to center in cross direction and respectively for horizontal supports of zig-zag pattern and fixing of Gyp board in the panel provided in the design pattern given and spraying the ceiling surface same Gyp board same materials etc., -using perforated sheets

Using perforated Sheets(10mm thick)

Supplying and fixing in position Stainless steel door frame as per I.S.4351/1976 of size 100x60mm with 35x12mm rebate on all sides with 1.60 mm thick (18 gauge) sheet frames special profile extruded section including bottom tie hold faste at appropriate places and provision to fix aldrops tower bolts hinges and lock strike plate etc.The door frame inner shall be packed with CC 1:2:4 using 12mm guage HBG stone jelly including fixing the door frames inposition and dimantling the masonry and concrete wherever necessary and redoing the same original condition after fixing including scaffolding charges and labour charges and door frame will be given one coat of Red Oxide primer etc. Complete complying with standard specification The rate shall inclusive of all materials, labour, transportation, loading, unloading, handling, charges etc. The sample of materials should be got approved by the Exe. Engineer before use on works

Supplying and fixing door shutters for Medium Density Fibre board of exterior grade, Both side Pre laminated including external lipping with Kiln dried soft wood of 35mm thick conforming to IS 12406 / 1989 with necessary adhesive and C.P. screws, including fixing of aldrops, tower bolts, hinges and lock strike plates, putty, fevical, varnish for T.W. lipping with thinner colouring agent etc., The rate includes cost of materials and cost for aluminium furniture fittings such as 3 nos Alu. hinges 125mm, 1 no Alu. aldrop 250 x 16mm, 1no Alu. tower bolt of 200x12mm and 1 no Alu. tower bolt of 150x12mm, 2 Nos Alu. Handles, 1 no door stopper with rubber bush incase of Single leaf door inclusive of labour charges for fixing in position etc., complete. All Aluminium furniture fittings are to be anodised with matt finish under electrically controlled condition in accordance with ISI specification 1868/1968 for anodic film thickness of not less than 15 microns, The rate is inclusive cost of fevical and fixing charges, transportation, loading, unloading and all other incidential charges, handling charges etc., complete complying with standard specification. - Single leaf

Supplying and fixing door shutters for Medium Density Fibre board of exterior gradeBoth side Pre laminated including external lipping with Kiln dried soft wood of 35mm thick conforming to IS 12406 / 1989 with 35 x 12mm T.W. on all edges with necessary adhesive and C.P. screws, including fixing of aldrops, tower bolts, hinges and lock strike plates, putty, fevical, varnish for T.W. lipping with thinner colouring agent etc., The rate includes cost of materials and cost for aluminium furniture fittings such as 6 nos Alu. hinges 125mm, 1 no Alu. aldrop 250 x 16mm, 2nos Alu. tower bolt of 250x12mm and 1 no Alu. tower bolt of 200x12mm, 2 Nos Alu. Handles, 2 nos door stopper with rubber bush incase of Single leaf door inclusive of labour charges for fixing in position etc., complete. All Aluminium furniture fittings are to be anodised with matt finish under electrically controlled condition in accordance with ISI specification 1868/1968 for anodic film thickness of not less than 15 microns, The rate is inclusive cost of fevical and fixing charges, transportation, loading, unloading and all other incidential charges, handling charges etc., complete complying with standard specification. - Double leaf

Manufacturing, supplying and fixing Precast Reinforced Cement Concrete slabs of following thickness in RCC 1:2:4 (one cement, two Crushed Stone M-Sand and four aggregates), using following HBGS jelly excluding cost of reinforcement steel in position but including cost of moulding charges, casting of slab, finishing, curing and fixing in position in all floors etc., complete

50mm thick.

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm white glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with Crushed Stone M-Sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two Crushed stone Crushed Stone M-Sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to CI soil pipes (including the cost of 100mm dia CI pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works). White IWC with PVC pipe

Supplying and fixing in position white glazed European Water Closet of best quality and approved make with 100 mm "P" or "S" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings.....

such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank wiht all accessories should be got approved by the Executive Enginer before use on works) White glazed EWC with 10 litre capacity PVC flushing tank with CP brackets.

Supplying and fixing best approved best quality Stainles steel Health Facet with Stop coak of size 150 x 150mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications. (The soap tray should be got approved by Executive Engineer before use on works).

Supply and fixing in position of best Indian make white glazed earthernware lipped mouth flat back urinal of best quality and approved make of size 430mm x 260mm x 350mm with GI pipe, 32mm dia bell mouth PVC connection and waste pipe, 15mm dia GI pipe of required length, 15mm dia GM wheel valve, 15mm dia brass nipple 2 Nos., and fixing the urinals in position with necessary TW plugs, clamps, screws, etc., including dismantling masnory and re-doing the same to the original condition, etc., including painting the pipe with two coats of best quality approved synthetic enamel paint over one coat of red oxide primer and checked without any leakage etc. complete complying with standard specifications and as directed by the departmental officers. (The urinal should be got approved by the Executive Engineer before use on works.)

Supplying and fixing position PVC Nahani Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of Crushed stone Crushed Stone M-Sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three Crushed Stone M-Sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works) size 100 x 75mm

Supplying ,fabricating and fixing in position of stainless steel Scrub up sink of size 1200x550x180 mm with following specification the outter frame of the sink shall be made of 32mmx32mm size squre M S Tube section.A curved trough with 38cm depth made of stainless steel sheet of 1.60mm thick shall be fixed to the outer frame and the front side and the sides of the Sink shall be covered with Stainless Steel sheet of 1.60mm thick . A waste water coupling with drain arrangements shall be fixed to the through. The rate is inclusive of all materials ,labour charges ,transportation ,loading ,unloading and all other incidental charges etc complete.,

Supplying and fixing in position best quality and approved make Indian made white glazed earthernware wash hand basin of size 550 x 400mm without pedestal with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks)

Supplying and fixing approved best quality brass CP towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The towel rail should be got approved by Executive Engineer before use on works).

Supplying and fixing best approved best quality brass CP soap tray of size 150 x 100mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications. (The soap tray should be got approved by Executive Engineer before use on works).

Supplying and fixing in position 15mm dia brass CP screw down tap / Pillar tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)

screw down tap

Pillar tap

Supplying, laying and jointing CPVC pipes (chlorinated Poly vinyl chloride) pipe( Higher pressure rating with h ig her pipe thickness) Standard Dimension Ratio- 11)of approved qualityand best variety conforming to BIS of the following dia including cutting, threading and fixing CPVC specials using SOLVENT OF 118ML (but excluding cost of such specials) and fixing into wall with teak wood plugs,CPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The CPVC pipes shall be got approved by Executive Engineer before use on works.

External Water supply- Above Ground level

50mm dia CPVC pipe

40 mm Dia CPVC pipe

Internal Water supply- Above Ground level

32mm dia CPVC pipe

25 mm Dia CPVC pipe

20mm dia CPVC Pipe

Supplying, laying and jointing CPVC Union of approved quality and best variety etc., complete complying with standard specification. (The CPVC union should be got approved by the Executive Engineer concerned before use on works.)

CPVC UNION

50 mm dia Union

40 mm diaUnion

32 mm dia Union

25 mm dia Union

Supplying, laying and jointing CPVC Specials of approved quality and best variety etc., complete complying with standard specification. (The CPVC specials should be got approved by the Executive Engineer concerned before use on works.).

CPVC TEE

50 mm dia Tee

40mm dia Tee

32mm dia Tee

25mm dia Tee

CPVC Elbow

50 mm dia Elbow

40mm dia Elbow

32mm dia Elbow

25mm dia Elbow

20mm Elbow

CPVC Bend

25mm dia Bend

20mm dia Bend

15mm dia Bend

CPVC Reducer Tee

40x32mm dia Tee

32x25mm dia Tee

CPVC Reducer Elbow

32x25mm dia Elbow

CPVC Reducer

32X25mm dia Reducer

25X20mm dia Reducer

CPVC Hex nipple

25mm dia 'H' Nipple

Supplying, laying and jointing CPVC Ball valve of approved quality and best variety etc., complete complying with standard specification. (The CPVC Ball valve should be got approved by the Executive Engineer concerned before use on works.).

32 mm dia ball valve

25mm dia ball valve

20mm dia ball valve

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level

160mm dia PVC soil pipes

110mm dia PVC soil pipes

75mm dia PVC soil pipes

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

160mm dia PVC Elbow

160mm dia PVC Elbow with Door

160mm dia PVC Bend

160mm PVC TEE with Double Door

110mm dia PVC Elbow

110mm dia PVC Elbow with Door

110MM DIA PVC DOOR BEND

110mm dia PVC Bend

75mm dia PVC bend

110mm PVC Tee with Double Door

75 mm dia PVC Elbow

75 mm dia PVC Elbow with Door

75mm dia PVC TEE with double door

PVC cowl

110 mm dia

75 mm ida

Supplying and fixing New PVC WATER TANK of approved quality conforming to ISI.specification 1000 litre capacity having suitable cover, bolts including cost of tank, taxes, transportation to work spot, fixing in position at place as shown and as directed by the Departmental Officers including conducting required water test complete complying with standard specification.

Drilling of vertical borewell of 6" dia. (150mm) anywhere in Tamilnadu including transporation from one place to another place with in Tamilnadu sedimentary strata of clay and Crushed Stone M-Sand or Crushed Stone M-Sand, stone, shale pebbles, boulders etc., at the site shown by the TWAD officers including construction of mud pit using Rotary Rig are to be used. (TWAD)

Supplying and delivery of PVC Casing pipe 160mm dia as per IS 12818/1992 with ISI Marking of following diameter in 3m length with screwed and socket end and centering guides for every 15m length of pipe to suit deep bore wells for delivery including loading, unloading, freight, insurance etc., complete (Rate inclusive of Excise duty)

160mm dia Special Pipes for Bore Well

Supplying and fixing of suitable 160mm PVC endcap (6kg/cm2)for 6"dia borewell of best quality with ISI mark (the PVC endcap should be not approved by the departmental officers before execution)

Supplying of best and approved quality of HDPE pipe of the following size including laying in the borewell and tying with copper wire etc., complete complying with standard specification

For HDPE pipe 25mm dia

For HDPE pipe 20mm dia

Supplying and fixing of 3 HP Compressor block motor with all accessories including giving necessary electrical connection and as directed by the departmental officers.

Supplying and fixing of 1 HP Monoblock motor with all accessories including giving necessary electrical connection and as directed by the departmental officers.

Pre-Construction anti-termite treatment plinth area – surface treatment stage-1 :- Completion of earth work for column footings before laying plain cement concrete 25mm dia Hole spaced at 30cm center to center on both direction will be made at the bottom of earth workand the chemical will be poured in the holes and will be sprayed in the four sides of earth work at the rate of 3 litres of chemical solution (Chlorophyrifos emulsion diluted in ration 1:19 (One emulsion and 19 water ) per square metre payment shall be made after completion of 3 stages. stage-II :- After filling the basement before laying flooring concrete with filling Crushed Stone M-Sand 25mm dia holes to adepth of 450mm will be made inside the basement and the chemical will be poured in the holes at the rate of 3 litres of chemical solution (Chlorophyrifos emulsion diluted in ration 1:19 (One emulsion and 19 water ) per square metre payment shall be made after completion of 3 stages

Peripheral treatment stage-III.On completion of building and leveling the outer area adjacent to the walls column ground ponds of size (900X300 mm will be filled in the ponds at the rate of 3 litre of chemical solution per Rm payment shall be made after completion of 3 stages. Stage-IV.Spraying termite solution around the building (Out side of the building) by making crowbar holes around the building before laying the plinth protection. This holes has to be closed after the treatment

Medical Gas Copper Pipeline arrangement to hang on the wall of socket type connection installation of seamless cleaned and degreased non arsenical phosphorous gas copper pipe line with saddles complete with brazing work including all copper fitting (tee, elbow, reducer, coupling). The copper pipelines should be tested suitable for a steam of working pressure of 17.34 kg. / cm2 (17 bar) and confirm to BS 864 Standard with specially made for brazed socket type connection. The medical gas copper pipeline should be tested as per standard and commissioning after painting as per International Code No. IS 2379/1963 Table-V. The pipelines installed at the various wings and floors etc., complete as directed by the Departmental Officers as per IS Code 12827 / 1989 & ISO 7396 / 1987 Specification.

28mm OD 0.90 mm thick Copper pipe

22mm OD 0.90 mm thick Copper pipe

15mm OD 0.90 mm thick Copper pipe

10mm OD 0.90 mm thick Copper pipe

Oxygen manifold arrangements of 2 banks x 12 cylinder each wing with semi automatic control panel which includes contact gauge 2 Nos., outlet pressure gauge, brass heavy duty IO x regulator 2 Nos. with suitable adopter, flexible SS Hose. Mainfold shall be of a construction and of a designs and material suitable for the service pressure in accordance with IS 1282- 1989. Emergency alarms with illuminating display for low / high pipeline pressure and malfunctioning of system. 1) Mainfold top frame with provision for connecting 12 cylinders on right bank and 12 cylinders on left bank with high pressure interconnecting copper tubing, silver brazing, non return valve, fasteners and cylinder spport middle angle frame for claping 2 x 12 cylinders and related fasteners. The O2 manifold should with stand a pressure of 140 kg. / CM2. The installation is commissioned after testing as per standards and painted as per International Code and as directed by the Departmental Officers as per IS Code 12827 / 1989& ISO 7396 / 1987 Specification.

Supply, installation, testing and commissioning of Compressed Air System of Reciprocating Oil Free Air Compressor Belt Driven Type 10 HP Air Compressor with following provisions. As per IS 12827 / 1987 & ISO 7396 / 1987 Specification Compressor package consists of following: a) 10 HP Air Compressor - 1 No. b) Electric Motor 10 HP - 1 No. c) Dol Starter - L&T - 10 HP - 1 No. d) Base Frame Kit (for Motor and Compressor) - 1 set e) Pressure Swith - 1 No. f) Pressure Gauge - 1 No. g) NRV and Pilot Fittings - 1 No. h) Delivery Tube - 1 No i) Foundation Bolts & Anchor Fasteners - 1 Lot j) Belt Guard - 1 No. k) Refrigerator Type Air Dryer-40 cfm. capacity-1 No. l) Drain Ball Valve - 1 No. m) Air Outlet Ball Valve - 1 No. Vacuum Room & Air Compressor Room Inside Accessories: Non-Return Valves, Air Pressure Switch, Pressure Gauge, Isolation Valves, Air Filters etc., Inter connecting piping: Mild Steel Pipe of 2" with fittings,

Supply, installation, testing and commissioning of MS Fabricated Vertical Mounted Type 1000 liters capacity Compressed Air Receiver with inlet and outlet and drain holes provided suitable to operate with vaccum pump etc as directed by the Departmental Officers.

a)5 H.P Vacuum compressor Type: Reciprocating Air – Cooled Type of Motor : 5 HP with Non return valve, pressure gauge & Isolation valve b) 5 H.P Vacuum compressor Type : Reciprocating, Air cooled Motor Capacity: 5 H.P with Non return valve, pressure gauge & Isolation valve

Supply, installation, testing and commissioning of MS Fabricated Vertical Mounted Type 1000 liters capacity Vaccum Receiver with inlet and outlet and drain holes provided suitable to operate with vaccum pump, etc., as directed by the Departmental Officers.

Gas Outlet Points: (Self sealing type - Single / DIN outlet pipe) with 'S' type bracket made up of copper and the out let of non-Interchangeable for other gas. The outlet points are brazed with brass bracket with self sealing valve (Stainless Steel) with all accessories and complete set and are covered by plastic cover duly colour coated as per specific gas and button cover etc., complete as directed by the Departmental Officers and as per IS Code 12827 / 1989 & ISO 7396 / 1987 Specification.

Flow Meter made up of Brass with Humidifier Bottle Flow Meter should be back pressure compressed and should be accurate gas flow measurement with control range 0-13 litres per minute. It should meet strict permission and Bumbling standard. The meter body should be made of brass materials. The humidifier bottle should be made of unbreakable polycorbonate material and auto cleavable at 134 degree centigrate. The rate includes flow meter and its accessories (silicon tube with mask). The cost of materials including transport, etc., complete as per standard specification and as directed by the Departmental Officer and as per IS 12827 / 1989 and ISO 7396 / 1987 Specification.

Ward Vaccum Unit with Gauge both mounted on a collection jar of capacity 600 ml and with a wall bracket for mounting it on the wall. The collecion jar should be made of unbreakable polycarbonate materials which is fully auto cleavable at 134 degree centigrade as per standard specification and as directed by the Departmental Officers and as per IS 12827 / 1989 and ISO 7396 / 1987 Specification. The rate includes cost of silicon hose with SS nipple on either side.

Brass Isolation Valve suitable for the copper pipe and should be of non lubricated 90 degree turn lever ball I, valve of reputed make, conneced in line with medical gas pipe line system by using suitable size brass valve adopter union, ferrule, nipple, rubber "0' ring, tapion lap and etc. All pipe line regulators shall be capable of controlling pipe line pressure and must compatible with the requirements specified in IS 12827-1989. All valves should be pneumatically tested for twice the working pressure for the gas line as per IS Code 12827 / 1989 & ISO 7396 / 1987 Sepecification.

22 mm Isolation valve

15 mm Isolation valve

Supply and fixing of 25mm dia GI Pipe Above ground level

D' type cylinder for O2

Supply of Unskilled labours (Mazdoor category I) for assisting in uprooting the existing trees and replanting the tress including cutting tree branches leaves and staking the cut trees branches at the place shown by the departmental officers.

Hire charges for JCB Machinery with one operator & one helpers for the purpose of uprooting and replanting the eixsting trees to the transplanting positions and transporting the cut branches to the stacking place shown by the departmentals officers and digging the new pits for transplantation of tress and clearing the waste and garbages etc complete . The rates are inclusive hire charges for machinery, labour charges, fuel charges and incidential charges and as directed by the departmental officers.

Hire charges for wood cutting machine (Mechanised) with operator for cutting the wooden branches and stems while uprooting and transplanting the trees. The rates are inclusive of fuel charges, labour, hire charges for machine and all other incidential charges and as directed by the departmental officers.

Hire charges for 14 tonnes Crane for shifting the uprooted tress to the transplantation position as shown by the departmental officers. The rate inclusive of hire charges for machinery, cost of fuel, operator labour charges and all other incidential charges etc., complete as per the direction of the departmental officers.

Engaging tree transplantation experts for uprooting and transplantation of various girth size of trees after pruning the tree branches and applying fungicide in cutting edges,excavating alaround the tress providing root ball applying rooting enzyme in old roots making the new pits and treated as pest free. The trees are transplanted in new pits with the help of JCB and Cranes and refilled with Crushed Stone M-Sand , manure ,mother soil and maintanance of trees for a period of 90 days

Girth of 90 cm to 120 cm .

Girth of 30cm to 60cm

Supplying and fixing Galvalume colour sheet roofing with 0.47mm thick of approved quality by drilling holes (and not by punching) with necessary ‘J’ / ‘U’ bolts and nuts etc., complete complying with standard specification and as directed by the departmetal officers

Supplying and fixing 50mm dia GI pipe for Purlins including labour charges for cutting, welding and fixing with A.C. Sheet roofing etc., as directed by the departmental officers

Cement Concrete 1:3:6 (One Cement, Three Crushed Stone M-Sand and Six broken stone jelly) using 40mm size hard broken stone jelly for dummy columns, excluding cost of centering shuttering reinforcement grills and fabrication charges but including curing etc. complete. Dummy columns should be at least 1 metre height) in Ground Floor

Cement Concrete 1:4:8 (One Cement, Four Crushed Stone M-Sand and eight hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification

Manufacturing, supplying and fixing in position steel shetted Windows Two leaves of the following types; outer frames and shutter frames shall be made out of steel sections confirming to IS.7452 / 1990 t of ‘Z’ section (F.7D) of size 25mm x 20mm x 3mm and mullions are made of (F4B) ‘J’ sections of size 46mm x 25mm x 3mm and sash bars shall be made of ‘T’ section (T2) of size 25mm x 22mm x 3mm. including providing handle cum latch with suitable open shall be left for its easy operation and adjustable wind stay of sufficient length shall be provided for each shutter and with necessary MS angle hold fasts welded to the outer frame and 12mm MS square guard bars shall be welded to the inner flat of the window at equal intervals not exceeding 100 mm spacing and welding 18G MS sheet for panes and including one coat of red oxide primer and charges for fixing in position including dismantling the masonry, concrete and redoing the same duly packed with concrete etc., complete and as directed by the departmental officers.

Supplying and fixing in position of Rolling shutter complying with standard specifications and as directed by the departmental Officers. (Manually Operated)

Design Fabrication, Supply and erection of bar screen made of MS 10mm square bars to suit the channel. Inner size of channel 1000mm , wide 900mm liquid depth and 1200mm length. The MS 10mm square bars should be properly epoxy coated to avoid the rusting of bars. The spacing between the square bar is 5mm, so that the particles above 5mm will be retained in the entry channel and will be cleared by hand rac manually. The bar screen should be kept at an inclination of 60o. The bar screen is fixed at site, inside the channel with a groove like arrangements, so that bar screen could be removed for maintenance purpose. The cost includes cost of MS bars, fabrication charges, Epoxy painting charges and fixing at site transport charges to site., etc., complete.

Design Supply and erection of Tube Settler feed pump with motor with the capacity of 6m3 /hr as per the design. The type of the pump is submersible sewage disposer 1 H.P , Non clog. The pump make is kirloskar/CRI/equivalent, The capacity of the motor is 1.0 HP. The type of the motor is TEFC, IP55, CLSS-B insulation, suitable for 3 phase supply, 440V, 50HZ .Motor make is Kirloskar/CRI/ Equivalent. Necessary base frame, foundation bolts nuts are provided to fix the coupled pump set above the foundation bed. The cost includes the pump, motor, Stand by pump and motor, base frame, foundation bolts, labour charges, erection charges, transport charges etc., complete.

Design Supply and erection of Coagulant dosing pump with the capacity of 0-6 liters per hour @ 4 kg/cm2, with 0.16 HP. The material of construction of the dosing pump is polypropene. The pump is fitted Base frame necessary bolts and nut . The capacity of the tank 200 liters with HDFE. The pump is fitted with a suction and delivery line. Necessary foot valve, level indicator is provided with the pump. Including the suitable Agitator for dosing pump The cost includes the cost of the pump, tank, foot valves, delivery and suction tubes of standard length, Agitator, labour charges, transport charges, erection charges etc., complete.

Design Supply and erection of Flocculent dosing pump with the capacity of 0-50 liters per hour @ 4 kg/cm2, with 0.16 HP . The material of construction of the dosing pump is polypropene. The pump is fitted Base frame necessary bolts and nut . The capacity of the tank 200 liters in HDPE. The pump is fitted with a suction and delivery line. Necessary foot valve, level indicator is provided with the pump. Including the suitable Agitator for dosing pump The cost includes the cost of the pump, tank, foot valves, delivery and suction tubes of standard length, Agitator, labour charges, transport charges, erection charges etc., complete.

Design Supply and erection of air blowers Ring Blower with electrical Motor, 16 m3/hr, 1 HP motor . Air blower with motor are provided for one number for operational and one number for standby. The Air blower make is of Raico/Equivalent to suit the design requirements. The Air blower with motor is fixed in a base frame. Necessary foundation bolts, nuts are provided to fix the total coupled assembly of Air blower and motor in the concrete bed. The cost includes the cost of Air blower, base frame , diffusers, foundation bolts, erection charges, transport charges, labour charges., etc., complete.

Design, Fabrication, supply, erection of tube settler media with PVC 1000mm depth 1.1mm thickness in hexagonal chevron shaped fixed with 60 degree slope in tube settler tank including the cost of tube settler media, erection charges , transport charges, labour charges.etc., complete

Design Supply and erection of Crushed Stone M-Sand Filter feed pump with motor with the capacity of 5 m3 as per the design. The type of the pump is horizontal, Centrifugal, flexible coupling drive arrangement. The pump make is kirloskar/CRI/equivalent, The capacity of the motor is 2 HP. The motor type suitable for 3 phase supply,440v, 50hz . Motor make is Kirloskar/CRI/Equivalent. Necessary base frame, foundation bolts nuts are provided to fix the coupled pump set above the foundation bed. The cost includes the pump, motor, Stand by pump and motor, base frame, Motor Guards, foundation bolts, labour charges, erection charges, transport charges etc., complete.

Design Supply and erection of Oxidant dosing pump with the capacity of 0-6 liters per hour @ 4 kg/cm2, with 0.16 HP . The material of construction of the dosing pump is polypropene. The pump is fitted Base frame necessary bolts and nut . The capacity of the tank 60 liters in HDPE . The pump is fitted with a suction and delivery line. Necessary foot valve, level indicator is provided with the pump. Including the suitable Agitator for dosing pump The cost includes the cost of the pump, tank, foot valves, delivery and suction tubes of standard length, Agitator, labour charges, transport charges, erection charges etc., complete.

Design Supply, fabrication and erection of Multi graded Crushed Stone M-Sand filter unit with 750 mm dia and 1500 mm height. Multi graded Crushed Stone M-Sand filter is a vertical, cylindrical vessel made out of 6mm thick MS Plate with inlet, outlet and back wash provisions. Fully Automated System including backwash The inlet pipe inside the vessel is designed to have a bell mouth arrangements for liquid/water distribution, so that the filter media is in position & will not get disturbed. The bottom collection system is provided with header and lateral pipe arrangements with necessary holes. The filtered water is collected thro this header lateral pipes, will flow out to outlet pipes and vice versa. The filter media consists of Multi graded Crushed Stone M-Sand filled over & under bed media of pebbles and gravels. The size and height of the filter media is as per the design and standards. Both the top and bottom dish ends & side wall are made out of 6mm MS Plates. The inner side of vessel is painted with epoxy painting, where as the outside with enamel painting . necessary man hole is provided as per the design and drawing.

The joints are properly vessel (Multi graded Crushed Stone M-Sand Filter ) is supported by MS legs, thereby fixing the vessel with foundation bolts properly in the concrete foundation bed. The cost includes the cost of materials like MS Plates for vertical cylinder and dish ends, inner piping for inlet and header lateral outlet arrangements, man holes, bolts, nuts and washers, filter media, foundation bolts fabrication charges, welding charges, erection charges, transport charges etc., complete.

Design Fabrication, Supply and erection of Bag filter with 20 micron with 5 m3/hour with Polypropylene Gadridges with 5 1/2 " dia 20" length. The cost includes cost of bag filter, stand , fabrication charges, and fixing at site transport charges to site., etc., complete.

Design Supply, fabrication and erection of Eco Ozotex with Ozone Generator includes the ozone recirculation pump in 4 m3 /hour. The type of the pump is horizontal, Centrifugal, Non clog, self priming flexible coupling drive arrangement. The pump make is kirloskar/CRI/equivalent, The capacity of the motor is 1 HP. The type of the motor is TEFC, IP55, CLSS-F insulation, suitable for 3 phase supply, 440V, 50HZ . ozone generator with a capacity of 100 gms / hour with oxygen concentrator, including the cost of epoxy coating for ozone reactor tank, water ozone mixing equipments with level gauge, safty valve with 1 HP motor. The cost includes the ozone generator, oxygen generator, ozone recirculation pump, motor, Stand by pump and motor for ozone recirculation pump, base frame, Motor Guards, foundation bolts, labour charges, erection charges, transport charges etc., complete.

Design Supply, fabrication and erection of Activated Carbon filter unit with 750 mm dia and 1500 mm height. Activated carbon filter is a vertical, cylindrical vessel made out of 6mm thick MS Plate with inlet, outlet and back wash provisions. Fully Automated System including backwash The inlet pipe inside the vessel is designed to have a bell mouth arrangements for liquid/water distribution, so that the filter media is in position & will not get disturbed. The bottom collection system is provided with header and lateral pipe arrangements with necessary holes. The filtered water is collected thro this header lateral pipes, will flow out to outlet pipes and vice versa. The filter media consists of granular activated carbon filled over & under bed media of pebbles and gravels. The size and height of the filter media is as per the design and standards. Both the top and bottom dish ends & side wall are made out of 6mm MS Plates.

The inner side of vessel is painted with FRP painting, where as the outside with enamel painting . necessary man hole is provided as per the design and drawing. The joints are properly vessel (Activated carbon filter) is supported by MS legs, thereby fixing the vessel with foundation bolts properly in the concrete foundation bed. The cost includes the cost of materials like MS Plates for vertical cylinder and dish ends, inner piping for inlet and header lateral outlet arrangements, man holes, bolts, nuts and washers, filter media, foundation bolts fabrication charges, welding charges, erection charges, transport charges etc., complete.

Design Supply and erection of Back wash pump with motor with the capacity of 5 m3 /hr , head of 3m as per the design. The type of the pump is horizontal, Centrifugal, Non clog, self priming flexible coupling drive arrangement. The pump make is kirloskar/CRI/equivalent, The capacity of the motor is 3 HP. The type of the motor is TEFC, IP55, CLSS-F insulation, suitable for 3 phase supply, 440V, 50HZ . Motor make is Kirloskar/CRI/Equivalent. Necessary base frame, foundation bolts nuts are provided to fix the coupled pump set above the foundation bed. The cost includes the pump, motor, Stand by pump and motor, base frame, Motor Guards, foundation bolts, labour charges, erection charges, transport charges etc., complete.

Design Supply and erection of Treated tank recirculation pump of capacity 15 m3/hour @ as per the design. The Treated tank recirculation pump is of horizontal, centrifugal, non clog self priming type . The pump make is Kirloskar/CRI/equivalent to suit the above said flow rate and head. The pump is coupled with motor by flexible coupling drive arrangements. The purpose of the pump is to recirculation for treated tank . The type of the motor is TEFC, IP55, CLSS-F insulation, suitable for 3 phase supply, 440V, 50HZ,. The capacity of the motor is 1 HP. The motor make is Kirloskar/CRI/ Equivalent. The cost includes cost of pump, motor, base frame, Motor Guards, foundation bolts, labour charges for erection, transport charges etc., complete.

Design Supply, Fabrication and erection of piping for sewage treatment plant of capacity 100 m3 The piping work consists of 1) Suction lines from Equalization tank, delivery lines to Tube settler thro' raw sewage transfer pumps. 2)Pipe lines for Blowers to Equalization tank Both MS and PVC pipes with necessary valves, pressure gauges are used as per the design and suit the flow rate. 3)Pipelines from Clarifier tank Bag filter and Multigraded Crushed Stone M-Sand filter 4)Pipe line from multigraded Crushed Stone M-Sand filter to Eco Ozotex reactor and Eco Ozotex reactor to Activated Carbon Filter 5) Pipe line from Backwash pump to Mutigraded filter and Activated Carbon filter 6) Necessary pipe lines , valves, pressure Gauge for filters, flow meters for tube settler feed, Crushed Stone M-Sand filter , Activated Carbon filter, float level switch

The total piping network as given above, is within the sewage treatment units. The cost includes the cost of pipes (MS, UPVC and 1" dia to 3"dia), Specials, valves, pressure gauges, flow meters, pipe fittings, fabrication charges, labour charges, transportation charges etc, complete.

Design, Fabrication, supply, erection of electrical panel board with necessary starters, main switches, voltmeter, ammeter, and electrical cables of required sizes from pumps to panel board as per design. The size of panel board is approximately 3 feet x 3 1/2 feet, fabricated with MS sheets and powder coat. Necessary provisions are given in the panel board for bus bars, main switch , starters, switches, voltmeter ammeter as per the design to suit sewage Treatment plant motors. The cables are run from panel board to the all pumps and other electrical accessories such as level switches dosing pumps etc complete,. The cable sizes are as per the design and suitable for electrical motors fixed in the Sewage treatment Plant. No lighting points are considered. The cost includes the cost of panel board, starters, switches, voltmeter, Ammeter, main switch, cables for motors, labour charges etc., complete.

Design Supply and erection of centrifugal desludger pump with motor with the capacity of 100 m3 , as per the design. The pump make is kirloskar/CRI/equivalent, The capacity of the motor is 1 HP. The type of the motor is TEFC, IP55, CLSS-F insulation, suitable for 3 phase supply, 440V, 50HZ, 300mm Basket dia. Motor make is Kirloskar/CRI/Equivalent. Necessary base frame, foundation bolts nuts are provided to fix the coupled pump set above the foundation bed. The cost includes the pump, motor, , base frame,, foundation bolts, labour charges, erection charges, transport charges etc., complete.

Design, supply and erection of Neutralization or Precipitation tank for 2 m3 flow per hour with Dosing System for Oxidant dosing and suitable agitator , base frame, foundation bolts, labour charges, erection charges, transport charges precipitation tank etc., complete the rates

Design Supply, fabrication and erection of on line disinfection for effluent with Ozone in Ground Level Reactor including submersible Mixing arrangement @ the pump make is CNP / Toshio Equivalent, The capacity of the motor is 1 HP. The type of the motor is Self aspirating, non clogging with SS304 impeller , and SS 420 Shaft, suitable for 3 phase supply, 440V, 50HZ including the cost of water ozone mixing equipments with level gauge, safety valve includes the ground level reactor, motor Submersible mixing unit base frame, SS Casing,Motor Guards, foundation bolts, labour charges, erection charges, transport charges etc., complete.

Design, Supply of Ozone Generator with Capacity of 10 gm/ hour with oxygen Concentrator, including the cost of Ozone Generator, Oxygen Concentrator and Control Panel etc. Complete

Design, Fabrication, supply, erection of electrical panel board with necessary starters, main switches, voltmeter, ammeter, and electrical cables of required sizes from pumps to panel board as per design, The size of panel board is approximately 2 feet x 2 feet, fabricated with Ms sheets and powder coat. Necessary provisions are given in the panel board for main switch, starters, switches, voltmeter ammeter as per the design to suit Effluent Treatment plant. The cables are run from panel board to the all pumps and other electrical accessories such as level switches dosing pumps Pumps, mixing units etc complete., the cable sizes are as per the design and suitable for electrical motors fixed in the effluent treatment plant. No lighting points are considered. The cost includes the cost of panel board, starters, switches, voltmeter, ammeter, main switch, cables for motors, labour charges etc., complete.

Supplying and filling 40 mm guage HBGS stone jelly for dispersion trench including loading conveying and unloading and as directed by the departmental officers etc., complete complying with standard specification.

Supplying and filling 20 mm guage HBGS stone jelly for dispersion trench including loading conveying and unloading and as directed by the departmental officers etc., complete complying with standard specification.

Electrical Items Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (5 points / Coil) (Higher End)

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (6 points / Coil) (Higher End)

Supply and fixing of 9W LED lamp (Havells / Eq) in existing BH point.

Supply and fixing of WT bulk head fitting with guard suitable for 9W LED lamp (Havells /Eq) with lamp.

Supply and fixing of 24W TRIM CLIPON LED (Havells make / Eq) Recess Cum surface mounting square type fitting of cool white output with integral driver and necessary connections complete.

Supply and fixing of square type recessed 2' x 2' 36W LED luminaire (Philips / Havells / Eq) on false ceiling with steel chain and PVC unsheathead copper leads from terminals to the fitting.

Supply and fixing of single box type 4'-20 W LED fitting (Philips / Havells / Eq) with CRCA body complete with TW round blocks on wall or ceiling with 20 W LED tube with PVC unsheathed Copper leads from terminals to the fitting.

Supply and fixing of single box type 4'-20 W LED fitting (Philips / Havells / Eq) with CRCA body complete with conduit pipe suspension from the ceiling with PVC unsheathed Copper leads from terminals to the fitting with 20W LED tube.

Supply and fixing of Twin box type 4'-20 W LED fitting (Philips / Havells / Eq) with CRCA body complete with conduit pipe suspension from the ceiling with PVC unsheathed Copper leads from terminals to the fitting with 2 nos of 20W LED tubes.

Supply and fixing of 48W LED street light fitting with LED (Higher End) with 32mm dia. GI pipe (class B) with 1 no.32 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting .

Supply and fixing of 1200mm (48") sweep AC ceiling fan High speed complete with 2 module 100W fan step regulator (Higher End) with 300 mm down rod on the existing fan clamp

Supply and fixing of 300 mm (12") sweep (light duty) AC exhaust fan complete without provision of hole in the wall.

Supply and fixing of louvers shutters arrangements for 300mm (12”) sweep (light duty) AC Exhaust fan.

Supply and fixing of 16"(400 mm) wall mounting fan (Orient Electric Wall-49) with remote with suitable clamps and necessary conections complete.

Supply and fixing of 100W LED flood light fitting (Crompton make / Eq) made up of pressure die cast aluminium housing with toughened glass and high power LED's of 5700K CCT, system efficacy ≥110 LPW with 4kV internal surge protection and IP66 rating fitting mounted on suitable angle iron frame work with necessary connection complete.

Supply and fixing of 1 no.6A two module 5 pin socket , 1 no. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. (Higher End)

Supply and run of 2 of 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade inrigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making goodof the concealed portion with suitable colour. (For 6A plug)

Supply and fixing of 3nos.6A two module 5 pin socket, 3 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. (Higher End)

Supply and fixing of 1 no.6/16A two module socket, 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. (Higher End)

Supply and fixing of 20A DP plug and socket in sheet enclosure with 32A DP MCB in flush with wall with earth connection (For AC Plug) (Legrand / Hager make)

Supply and fixing of 32A DP MCB in sheet enclosure in flush with wall with earth connection. (The MCB and metal enclosure should be with Legrand / Hager make)

Supply and run of 2 of 4 sqmm (56/0.3) PVC insulated SC unsheathed Cu. Conductor of 1100V Grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14SWG TC wire and making good of the concealed portion with suitable colour. (For AC plugs and power plugs)

Supply and fixing of 32A FP MCB in sheet enclosure in flush with wall with earth connection. (The MCB and metal enclosure should be with Legrand / Hager make). (For Ductable AC units)

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with IP 42 protection with 1 no. 32A DP MCB switch as incoming and 6 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. (Higher End) (Lift Machine room)

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with IP 42 protection with 1 no. 32A DP MCB switch as incoming and 10 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. (Higher End) (For LDB)

Supply and run of 2 of 6 sq.mm. (84 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade insuitable PVC rigid pipe concealed in wall and ceiling with contiinuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour. (For LDBs)

Supply and fixing of 7 segment 4 way triple pole neutral MCB distribution board in sheet steel enclosure double door type with metal door with IP 43 - IK 09 protection with 40A 4 pole MCB as incoming and 3Nos 40A DP RCCB as sub incomer and 12 Nos. 6 A to 32 A SP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection. (The MCBDB and MCB's should be with Legrand / Hager make) (MLDB For Each Floor )

Supply and run of 4 of 6 sq.mm. (84 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 14 SWG TC wire and making good of the concealed portion with suitable colour. (7 Seg MLDB & 32A FP)

Supply and fixing of Vertical type 4 way triple pole neutral MCCB distribution board in sheet steel enclosure double door type with metal door with IP 43 - IK 09 protection with 125A 4 pole MCCB as incoming and 4Nos 63A TP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection. (The MCCBDB and MCB's should be with Legrand / Hager make) (Ground floor Main LDB)

Supply and clamping of 3-1/2 x 70 sq.mm aluminium PVC LTUG armoured cable on post or on wall with MS clamps.

Supply and fixing of brass cable gland for 3-1/2 x 70 sq.mm aluminium PVC LTUG armoured cable with earth connection

Supply and providing cable end termination of 3-1/2 x 70 sq.mm PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete.

Supply and fixing of 7 segment 6 way triple pole neutral MCB distribution board in sheet steel enclosure double door type with metal door with IP 43 - IK 09 protection with 63A 4 pole MCB as incoming and 3Nos 63A DP RCCB as sub incomer and 18 Nos. 6 A to 32 A SP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection. (The MCBDB and MCB's should be with Legrand / Hager make)(CP & 15A Plug )

Supply and fixing of 63A FP MCB in sheet enclosure in flush with wall with earth connection. (The MCB and metal enclosure should be with Legrand / Hager make). (For Ductable AC unit and UPS input and output)

Supply and run of 4 of 16 sq.mm (101/0.45) PVC insulated SC unsheathed Cu Conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 14 SWG TC wire and making good of the concealed portion with suitable colour.

Supply and fixing of 7 segment 4 way triple pole neutral MCB distribution board in sheet steel enclosure double door type with metal door with IP 43 - IK 09 protection with 100A 4 pole MCB as incoming and 3Nos 100A DP RCCB as sub incomer and 12 Nos. 6 A to 32 A SP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection. (The MCBDB and MCB's should be with Legrand / Hager make) (20A Plug )

Supply and fixing of Vertical type 4 way triple pole neutral MCB distribution board in sheet steel enclosure double door type with metal door with IP 43 - IK 09 protection with 100A 4 pole MCB as incoming and 4Nos 32A TP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection. (The MCBDB and MCB's should be with Legrand / Hager make).

Supply and fixing of Vertical type 8 way triple pole neutral MCB distribution board in sheet steel enclosure double door type with metal door with IP 43 - IK 09 protection with100A 4 pole MCB as incoming and 2Nos 63A TP MCB & 6Nos 32A TP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection. (The MCBDB and MCB's should be with Legrand / Hager make)

Supply and run of 4 of 25 sq.mm (168/0.45) PVC insulated SC unsheathed Cu Conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 14 SWG TC wire and making good of the concealed portion with suitable colour.(for VDB and 7 Seg DB each floor)

Supply and fixing of 63A TPN switch disconnector fuse units in sheet steel enclosure with HRC fuses double break on suitable angle iron frame work with MS cable entry boxes with earth connection only. (for lift and pump room)

Supply and laying of 3-1/2 x 35 sq.mm. PVC aluminium LTUG armoured cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering three sides of the cable completely with bricks and sand and refilling the earth to make good. (for 63A Switch)

Supply and clamping of 3-1/2 x 35 sq.mm. PVC aluminium LTUG armoured cable on post or on wall with MS clamps. (for 63A Switch)

Supply and fixing of brass cable gland for 3-1/2 x 35 sq.mm. PVC aluminium armoured LTUG cable with earth connection. (for 63A Switch)

Supply and providing cable end termination of 3-1/2 x 35 sq.mm. PVC aluminium LTUG armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete.(for 63A Switch)

Supply and fixing of 65 mm dia. (2 -1/2") GI pipe (class B) of 6 metre length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom with concreting with construction of masonary pedestal with suitable SMC box with door arrangement to house 6A SP MCB switch, 2/4 way connector on suitable hylem sheet and supply and fixing of 48W LED street light fitting with LED (Higher end) with 1 metre 32mm dia. GI pipe (class B) Complete with suitable MS clamps for LED steet light fitting and SMC box with PVC unsheathed copper leads from SMC box to fitting and with painting of suitable colour .

Supply, erection, testing and commissioning of dust & vermin proof Automatic ON / OFF three phase Street light Control panel made up of 16 SWG CRCA sheet enclosure of suitable size panel with powder coating, lock & key arrangements and accomodating the following with necessary internal wiring. a)24 hous programmable timer switch with shortest switching time 15 minutes - 1No b)63A FP MCB - 1 No c) 55A 3 pole AC-1 rating power contactor - 1No d) 6A single pole 2 way Auto/Manual Change over switch -1No e) 6A SP MCB - 1No f ) 4way terminal block - 1No (The Timer, Contactor, MCB & changeover switch should be Legrand / L&T / Siemens make).

Supply and fixing of brass cable gland for 2x16 sq.mm PVC aluminium LTUG armoured cable with earth connection. (for street light post)

Supply and laying of 4 x 16 sq.mm PVC aluminium armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering three sides of the cable completely with bricks and sand and refilling the earth to make good. (for street light post)

Supply and clamping of 4 x 16 sq.mm. PVC aluminium LTUG armoured cable on post or on wall with MS clamps. (for street light post)

Supply and clamping of 4 x 16 sq.mm PVC aluminium LTUG armoured cable in suitable dia Class B G.I pipe on post or on wall with MS Clamps. (for street light post)

Supply and fixing of 125A TPN switch disconnector fuse units in sheet steel enclosure with HRC fuses double break on suitable angle iron frame work with MS cable entry boxes with earth connection only.

Supply, erection, testing, Commissioning and Handing over of 125 kVA Diesel Generator set of 0.8 P.F, three phase 415V/ 420 Volts, 50Hz, 1500 RPM CPCB Approved capacity with 158 HP Engine Rated output of water cooled clock wise rotating feed pump with 100kW/ 125kVA operating capacity brushless alternator close coupled underneath fuel tank standard safeties LLOP with stop solenoid battery with lead Electric start and vibration fitting and accessories and AMF panel as detailed below including transporting & unloading charges. . (A) Engine: Water cooled diesel engine suitable for Generator application with a shaft out put of 158 HP at 1500 RPM under NTP conditions. The Engine shall comprise the following standard fitting flexible coupling fly wheel, air cleaner, fan blower, radiator, water pump, fuel filter, lubricating oil filter, etc.(Kirloskar Green / Cummins / Ashok Leyland make) (B) 12/24 Volt Electronic starting Equipment: Complete with starter motor, dynamo, standard batteries with cable, flexible exhaust piping of 50cms length

(C) Engine Instrument Panel / Mounted: Starting push botton / starting key, lubricating oil, temperature gauge, lubricating oil pressure gauge, water temperature gauge, safety control for low lubricating oil, pressure, safety control for high water temperature, safety control for over speed, hour meter (mechnical) and RPM indicator, battery charging ammeter. The engine should be capable of providing 10% over load for one hour for every 11 hours continuous at full load. D)ALTERNATOR: 125kVA/100kW Capacity of brushless alternator, AC 3 phase, 50Hz, 415/420V, 0.8 PF, 1500 RPM under NTP conditions, conforming to IS:13364 (Part-II)/ 1992 to be means of coupling. (Stamford make/ Eq) (E) AMF CONTROL PANEL: The AMF control panel (cubical) should be fabricated with vermin proof and dust proof best quality sheet steel and floor mounted with removable rear panels and hinged front doors with enamel painted and incorporating the following with suitable provision for connection incoming and outgoing leads having been made on the control panel.

27.Hooter/Audio alarm for indicating set fails to start and for DG O/L. 28.1set Timers 29.Audio and Visual indicator arrangements for: a) Low lubricating oil pressure b) High water temperature c) Over speed 30.1No Earth fault relay 31.Isolator to isolate the neutral 1. The control panel should be complete with necessary fuses, cables, label, other accessories with neutral isolation arrangements. 2. The engine should trip for the following: a) Low lubricating oil pressure b) High water temperature c) Over speed 3.Supply and fitment of Auto Mains Failure Panel, 1 EB Service wih 200 Amps switch and contactors SUF Control relays, timers etc suitable for auto change over of DG & EB Service. F.FUEL TANK 290 litres fuel tank shall be fabricated out of 14 SWG CRCA MS sheet and is part of base frame. It is duly painted and fitted with inlet and outlet connections and mechanical fuel gauge. Fuel tank can be easily removed for cleaning or any maintenance.

G.BASE FRAME: Base frame should be fabricated with MS channel frame of rigidly welded construction for mounting of generaor set. The engine and alternator should be coupled by suitably designed diaphragm type flexible coupling with guard and mounted on the base frame with proper alignment. H) ACOUSTIC ENCLOSURE: The Acoustic enclosure, Self standing weather proof KG- CPCB Typed Acoustic canopy KG 125WS floor mounting type with modular construction with the provision to assemble and dismantle easily and designed to suit all weather condtions. Erection of acoustic enclosure suitable for 125KVA Diesel generator complete with all accessories as above and suitable supports etc. Outer body 2 mm CRCA sheet steel door 2mm thick CRCA sheet. Inner surface 0.8m thick GI perforated sheet. Perforation area should be 2/3 of total area. Insulation : 100 mm thick rock wool / (Density 65 Kg / cub.m) or as approved by competent authority to suit CPCB norms. The maximum permissible sound pressure level for diesel generator (DG) set shall be 75 dB(A) at 1 metre from the enclosure surface.

Supply of manuals for operation & maintenance of DG set with warranty card etc. CEIG approval: Preparation of site plan physical layout, electrical line schematic Diagram 10 sets, getting drawing approval from CEIG preparation of complection report rectification report etc., arranging CEIG inspection and obtaining CEIG safety certificate, payment of CEIG inspection fees if necessary and preparation of one set of approval Drawing and copy of safety certificate in a neat frame work. (L)TESTING AND COMMISSIONING After the installation of DG set on its foundation, the DG set should be tested and commissioned with first charging of lubrication oil to its level, first charging of battery and run the set for eight hours on full load test complete. The Genset engine and alternator make should be approved by SE before used on work.

Supply and fixing of Exhaust Pipe with Silencer for 125kVA Genset.

Earthing as per the ISI specification with an earth electrode of 2.1mt class 'B' GI pipe of dia not less than 40mm, with copper earth plate of size 125mm x 50mm x 6mm, with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry

Earthing as per P.W.D standard with an earth electrode of 2 Mtr. Class 'B' GI pipe of dia not less than 32mm complete with necessary masonry work.

Supply and run of No-8 SWG Copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection.

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection.

Supply and run of 25mm x 6mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection.

Supply and run of 1 of No.8 SWG GI wire for earth connection.

Supply and laying of 3 ½ x 120sq.mm PVC aluminium armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 mt. Layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good.

Supply and clamping of 3 ½ x 120sq.mm PVC aluminium armoured LTUG cable on post or on wall with MS Clamps.

Supply and fixing of brass cable gland for 3 ½ x 120 sqmm PVC aluminium armoured LTUG cable with earth connection.

Supply and providing cable end termination of 3 ½ x 120 sqmm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete

Supply, Fabrication, erection of 315 A Capacity dust and vermin proof cubical LTCT metering panel board size of 900mm(L) X 1200mm (H)X 300mm (D) made up of 18SWG sheet steel for outer body, doors, switch and KWH meters, seperation , supports and with supply and fixing tinned copper flat for R,Y,B &N bus runs all round the panel to provide earth connection incoming Fuse, and meter chamber earth bus as section 315A fuse cutout for putty type & meter chambers provided with 5mm thick transparent glass at the front for reading purpose with sealing provision by TNEB and supply. The panel board should be painted with High quality powder Coated paint with superscriptions. The panel is equipped with 3nos 315/5A class 01 molded type CT coil.

Supply and fixing of 315A TPN switch disconnector fuse units in sheet steel enclosure with HRC fuses double break on suitable angle iron frame work with MS cable entry boxes with earth connection only

Supply and clamping of 3 1/2 x 240 sq.mm PVC aluminium armoured LTUG cable on post or on wall with MS Clamps. (For LTCT Service and main switch)

Supply and fixing of brass cable gland for 3 1/2 x 240 sqmm PVC aluminium armoured LTUG cable with earth connection.

Supply and providing cable end termination of 3 1/2 x 240 sqmm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete.

Supply and fixing of 600mm x 50mm 16SWG GI Hot dip galvanized powder coated preforated cable tray on ceiling or wall with necessary fastereners, bolt nuts and clamps. (Manibhadra make / Eq)

Supply and fixing of 65mm (2 ½ ") Class B GI pipe of 5 mtr length with 300mm x 300 mm x 6 mm MS base plate duly welded at the bottom of mansory pedastal with necessary connection complete.

Supply, fabrication, erection and comissioning of 315A capacity dust and vermin proof cubical panel board size of 6' X 1' X 5.5' made up of 16 SWG CRCA sheet steel for outer body, with doors, switch supports and seperations etc., and with supply and fixing of the following interior switch with bus bar chamber complete with 1 1/4" x 1/4" tinned cu. Flat for 3 phase, 1 " x 1/4" tinned cu flat for neutral, 1" x 1/8" tinned cu flat for earth connections with bus bar insulators. The following tinned Cu flat should be used for interconnection between busbar and switches: 1 1/4" x 1/4" tinned cu. Flat for interconnection of 1No 315A incoming switch to bus bar, 1" x 1/4" tinned cu. Flat for interconnection of 2 Nos 250A Outgoing switches to bus bar, 1" x 1/4" tinned cu. Flat for interconnection of 3 Nos 200A Outgoing switches to bus bar, 1"x1/8" copper flat for interconnection of 2 Nos 125A outgoing Switches to bus bar.

A separate chamber on top of one side should be provided with multi function meter to display Line & Phase Voltage, Phase Current, Power Factor and Frequency with one set of LED pilot lamp, fuse holder with suitable HRC fuse for each phase with suitable CT coil arrangements. The panel should be fabricated as per relevant IE rules & CEIG specification for accommodation of 8 Nos 3 phase switches and supply & fixing of the following switches. 1. 315 A TPN switch disconnector fuse units interior only with HRC fuses double break - 1No 2. 250A TPN switch disconnector fuse units interior only with HRC fuses double break - 2Nos 3. 200A TPN switch disconnector fuse units interior only with HRC fuses double break - 3Nos 4. 125A TPN switch disconnector fuse units interior only with HRC fuses double break - 2Nos.

In each cubical switch, live portion of bus bar should be shrouded by 6mm thick hylum sheet separators, and properly earthed by tinned solid copper flat as I.E rules CEIG sepecifications.The earth bus with two runs of 1" x 1/8"tinned copper flat must be run all round the panel to provide double earth connection. The panel should be painted with two high quality enamel paint over one coat of red oxide primer, the cable size, capacity of switch, location etc., should be marked with white paint and 2 Nos. metallic danger board affixed complete with mounting on base channel 3"x1½"x½" iron frame work support complete. (The TPN switches should be L&T / Siemens make only)

Supply, fabrication, erection and comissioning of 200A capacity dust and vermin proof cubical panel board size of 6.5' X 1' X 4.5' made up of 16 SWG CRCA sheet steel for outer body, with doors, switch supports and seperations etc., and with supply and fixing of the following interior switch with bus bar chamber complete with 1" x 1/4" tinned cu. Flat for 3 phase, 1" x 1/8" tinned cu flat for neutral, 1" x 1/8" tinned cu flat for earth connections with bus bar insulators. The following tinned Cu flat should be used for interconnection between busbar and switches: 1" x 1/4" tinned cu. Flat for interconnection of 1No 200A incoming switch to bus bar, 1" x 1/8" tinned cu. Flat for interconnection of 4 Nos 100A Outgoing switches to bus bar, no.8 SWG copper conductor for interconnection of 7 Nos 63A outgoing Switches to bus bar.

A separate chamber on top of one side should be provided with multi function meter to display Line & Phase Voltage, Phase Current, Power Factor and Frequency with one set of LED pilot lamp, fuse holder with suitable HRC fuse for each phase with suitable CT coil arrangements. The panel should be fabricated as per relevant IE rules & CEIG specification for accommodation of 12 Nos 3 phase switches and supply & fixing of the following switches. 1. 200A TPN switch disconnector fuse units interior only with HRC fuses double break - 1No 2. 100A TPN switch disconnector fuse units interior only with HRC fuses double break - 4Nos 3. 63A TPN switch disconnector fuse units interior only with HRC fuses double break - 7Nos

In each cubical switch, live portion of bus bar should be shrouded by 6mm thick hylum sheet separators, and properly earthed by tinned solid copper flat as I.E rules CEIG sepecifications.The earth bus with two runs of 1" x 1/8"tinned copper flat must be run all round the panel to provide double earth connection. The panel should be painted with two high quality enamel paint over one coat of red oxide primer, the cable size, capacity of switch, location etc., should be marked with white paint and 2 Nos. metallic danger board affixed complete with mounting on base channel 3"x1½"x½" iron frame work support complete. (The TPN switches should be L&T / Siemens make only) (Ground & First Power panel)

Supply, fabrication, erection and comissioning of 250A capacity dust and vermin proof cubical panel board size of 6.5' X 1' X 4.5' made up of 16 SWG CRCA sheet steel for outer body, with doors, switch supports and seperations etc., and with supply and fixing of the following interior switch with bus bar chamber complete with 1" x 1/4" tinned cu. Flat for 3 phase, 1" x 1/8" tinned cu flat for neutral, 1" x 1/8" tinned cu flat for earth connections with bus bar insulators. The following tinned Cu flat should be used for interconnection between busbar and switches: 1" x 1/4" tinned cu. Flat for interconnection of 1No 250A incoming switch to bus bar, 1" x 1/8" tinned cu. Flat for interconnection of 10 Nos 100A Outgoing switches to bus bar.A separate chamber on top of one side should be provided with multi function meter to display Line & Phase Voltage, Phase Current, Power Factor and Frequency with one set of LED pilot lamp, fuse holder with suitable HRC fuse for each phase with suitable CT coil arrangements. The panel should be fabricated as per relevant IE rules & CEIG specification for accommodation of 11 Nos 3 phase switches and supply & fixing of the following switches.

1. 250A TPN switch disconnector fuse units interior only with HRC fuses double break - 1No 2. 100A TPN switch disconnector fuse units interior only with HRC fuses double break - 10Nos In each cubical switch, live portion of bus bar should be shrouded by 6mm thick hylum sheet separators, and properly earthed by tinned solid copper flat as I.E rules CEIG sepecifications.The earth bus with two runs of 1" x 1/8"tinned copper flat must be run all round the panel to provide double earth connection. The panel should be painted with two high quality enamel paint over one coat of red oxide primer, the cable size, capacity of switch, location etc., should be marked with white paint and 2 Nos. metallic danger board affixed complete with mounting on base channel 3"x1½"x½" iron frame work support complete. (The TPN switches should be L&T / Siemens make only) (Second floor Power panel)

Supply, fabrication, erection and comissioning of 200A capacity dust and vermin proof cubical panel board size of 4.5' X 1' X 4.5' made up of 16 SWG CRCA sheet steel for outer body, with doors, switch supports and seperations etc., and with supply and fixing of the following interior switch with bus bar chamber complete with 1" x 1/4" tinned cu. Flat for 3 phase, 1" x 1/8" tinned cu flat for neutral, 1" x 1/8" tinned cu flat for earth connections with bus bar insulators. The following tinned Cu flat should be used for interconnection between busbar and switches: 1" x 1/4" tinned cu. Flat for interconnection of 1No 200A incoming switch to bus bar, 1" x 1/8" tinned cu. Flat for interconnection of 2 Nos 125A Outgoing switches to bus bar, no.8 SWG copper conductor for interconnection of 5 Nos 63A outgoing Switches to bus bar.

A separate chamber on top of one side should be provided with multi function meter to display Line & Phase Voltage, Phase Current, Power Factor and Frequency with one set of LED pilot lamp, fuse holder with suitable HRC fuse for each phase with suitable CT coil arrangements. The panel should be fabricated as per relevant IE rules & CEIG specification for accommodation of 8 Nos 3 phase switches and supply & fixing of the following switches. 1. 200A TPN switch disconnector fuse units interior only with HRC fuses double break - 1No 2. 125A TPN switch disconnector fuse units interior only with HRC fuses double break - 2Nos 3. 63A TPN switch disconnector fuse units interior only with HRC fuses double break - 5Nos

In each cubical switch, live portion of bus bar should be shrouded by 6mm thick hylum sheet separators, and properly earthed by tinned solid copper flat as I.E rules CEIG sepecifications.The earth bus with two runs of 1" x 1/8"tinned copper flat must be run all round the panel to provide double earth connection. The panel should be painted with two high quality enamel paint over one coat of red oxide primer, the cable size, capacity of switch, location etc., should be marked with white paint and 2 Nos. metallic danger board affixed complete with mounting on base channel 3"x1½"x½" iron frame work support complete. (The TPN switches should be L&T / Siemens make only) (Genset panel)

Supply and fixing of brass cable gland for 3 ½ x 150 sqmm PVC aluminium armoured LTUG cable with earth connection.

Supply and clamping of 3 ½ x 150 sq.mm PVC aluminium armoured LTUG cable on post or on wall with MS Clamps.

Supply and providing cable end termination of 3 ½ x 150 sqmm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete

Lightning Arrester arrangements Supply of 8 mm Aluminum Round Conductor. Tested as per IEC 62561.

Supply of Roof conductor holder for parapet- Polyamide Conductor holder: With M8 female thread or diameter 7mm, M8 Screw to connect the conductor holder. Weather and temperature resistant from -35 to +90 degree Celsius tested. Conductor holder @ 1 meter distance. Tested as per IEC 62561.

Polyamide roof cable holder for flat roof: DIN 48829 Form B1. Closed form with bottom. Filling weight 1Kg (frost-resistant concrete). Sleeve from polyethylene, black @ 1 meter distance. Tested as per IEC 62561.

Providing of cross universal connector: For T and cross connection, to route vertical down conductor /mesh formation made of hot dipped galvanised iron with necessary screws etc . Installed with 4 hexagonal bolts M8*25 with hexagonal nuts .

Providing of expansion piece with connector: For equalising temperature related length changes. Necessary on conductors length over 20 meters. For round conductor Rd 8/ALU. Tested for 100kA lightning current.

Connector: For T cross and parallel connectors. Quick installation using hexagonal bolt M10X30 high-grade hot dip galvanised. Conforms to the requirements according to DIN VDE 0185-305 (IS-IEC 62305)(2nos/expansion piece ).

Vertical air terminal with accessories:Providing of Air terminals as per IS-IEC -62305 part-3 Nominal size Ø10/16 mm aluminium rod: 2 Mtr Airterminal: semi-hard (E-AlMgSiO5 corresponds to DIN 48801) Suitable for high wind load. Tested as per IEC 62561

Vertical air terminal with accessories: Providing of Air terminals as per IS-IEC -62305 part-3 Nominal size Ø10/16 mm aluminium rod: 4 Mtr Airterminal: semi-hard (E-AlMgSiO5 corresponds to DIN48801) Suitable for high wind load. Tested as per IEC 62561

Providing of Stand for Fang Fix system 16 kg with base and clamp, made up of frost resistant concrete and clamp tested upto 100KA lightning current .

Providing of Stand for Fang Fix system 16 kg made up of frost resistant concrete.

Down conductor Supply of Test Joint (Folding Clamp) suitable to connect 8mm round conductor and max by 30x3 mm GI strip as specified in drawing and directed by Engineer. Tested for 100kA lightning current.

Ring & vertical earthing system Supply of Galvanised Steel Flat 30X3 mm thickness from earth electrode directly in ground as required. Flat conductor Hot Dipped Galvanized. Tested as per IEC 62561.

Providing of Cross connector for Flat: Suitable for 30mm Galvanised steel strip and max 40. Installed with 4 nos of hexagonal plate. Tested for 100kA lightning current.

Providing of flat conductor holder suitable for FL 30. Installed with 2 hexagonal bolts. Tested as per IEC 62561.

Providing of Plastic Corrosion Protection strip: Approx 1.1 mm thick. Width 50mm. Made of petrolatum- coated chemical fibre fabric.

Supply of UL Listed maintenance free ,Low carbon copper coated earth rod of 3 metre electrode having diameter of 14.2mm with copper coating thickness of 250micron tested as per IEC 62561-2

Supply of universal clamp made of SS to connect rod with flat conductor.

Earth conductivity enhancing mineral compound shall be of 25kg/pit tested as per IEC 62561-7,TCLP tested

Providing Heavy duty earth chamber of 5000kg load bearing capacity for earthing arrangements to ensure the safety of earthing system

SURGE PROTECTION: Supply and insallation Cabinet Type Class 1 and 2 Combined Model SPD to arrest surges and overvoltages in the power line due to lighning switching action etc. they must be installed in the incoming MCC panel / DB of the respective buling in parallel to the power circuit. Model: PSV4-12.5/400TT (3 phase power network)

Supply, Installation, testing and commissioning of 4TR cassette type airconditioning unit with indoor unit comprising of cooling coil, evaporator fan and motor controls, insulated drain pan enclosed in cabinet and 4TR outdoor unit complete with compressor, condenser fan and motor and enclosed in powder coated sheet metal cabinet Unit shall be suitable for operation on 415 +/- 10% Volts, 50 Hz, AC Supply, units shall be supplied with microprocessor control including following accessories; 1. filling of R-410A Refrigerant gas 2. Six core 1.5 sqmm control cable from indoor to outdoor unit. (Carrier/Bluestar make)

Supply and laying of 5/8" and 3/8" copper pipe (Extra beyond 3 metres supplied with AC unit)

HVAC arrangements: Supply, Installation, testing and commissioning and handing over of Air-Cooled self contained ceiling suspended 5.5 TR Ductable airconditioning units with indoor unit comprising scroll type compressor, cooling coil, evaporator fan and motor controls, insulated drain pan enclosed in sheet metal cabinet and 5.5 TR outdoor unit complete with condenser fan and motor and enclosed in powder coated sheet metal cabinet Unit shall be suitable for operation on 415 +/- 10% Volts,50 HZ, AC Supply, units shall be supplied with microprocessor control panel.

Supply, Installation, testing and commissioning and handing over of LAMINAR UNIT with Operation Theatre laminar air flow plenum at SS304 grade 1 mm thick casing with aluminium mini plate HEPA Filters & 0.3 Microns 99.97% Eefficiency and SS304 grade 1.2 mm thickness perforated grill with13 mm Thicness XLP insulation

Supply, fabrication and fixing of MS channel for mounting the Airconditioning Indoor Unit.

Supply, fabrication and fixing of MS channel for mounting the Airconditioning Outdoor Unit.

Supply and filling of R410A Refrigerant Gas

Supply, Fabrication and Erection of fabricated ducting made up of GI sheets of 22 Gauge thickness.

Supply, Fabrication and Erection of fabricated ducting made up of GI sheets of 24 Gauge thickness.

Supply and providing Acoustic for initial portion of Ducting with 12mm thick fiber glass rigid board covered with Tissue Paper and Aluminium Perforated Sheet.

Supply and fixing of extruded Aluminium powder Coated, supply and return Air Grilles / Diffusers with volume control dampers.

Supply and fixing of flexible Canvas connection

Supply and fixing of Duct Mouth Dampers

Supply and fixing of 50 mm thick Anti Vibrating Rubber Pads

Supply and providing thermal insulation of 9 mm thick vidoflex with Aluminium Foil.

Supply and fixing of Refrigirant piping out of hard drawn copper pipe set of 1-1/8" and 5/8" size

Supply and fixing of Drain piping out of 1.5" anti seal foaming pipe with performed GI fitting and Insulation of Nitrile rubber insulation etc.

Supply and providing of 1.5sqmm copper flexible cable

Supply and providing of 0.5sqmm 4 core flexible signal cable

Supply and fixing of 1" PVC water drain pipe line for split AC units

Lift arrangements: Supply, erection, testing, commissioning and handing over of 1 No 26 persons capacity bed cum passenger gearless Lift with machine room with the following Technical specifications Location :Government hospital, Ambasamudram 1. Type of lift : Hospital Lift 2. Capacity of lift : 26 persons capacity passenger lift (1768 Kgs) 3. Speed : 1 Metre / Sec 4. Type of Drive: Specific variable voltage variable frequency V3F drive with enhanced ride comfort and leveling functions. (Micro Processor Based) 5. No. of floors: Ground +2 floor 6. Total Travel: 7.2 metres 7. Levelling Accuracy: High level accuracy with smooth and jerk free stopping. 8. Construction of Car: SS 304 grade 18SWG High quality stainless steel car with Neat hair line finish vinyl flooring and false ceiling. 9. Position of machine: Directly above the lift shaft. 10. No. of landing entrance: one in front (3Nos.) 11. No. of car entrance: one in front only

24. Emergency Alarm Bell: Battery operated alarm bell to be provided with Automatic charging device 25. Emergency light: Battery operated light to be provided with Automatic charging device. 26. Fire Man’s switch: To be provided at ground floor 27. Minor builders work: included in the scope. 28. Scaffolding: Included in the scope 29. Sill angles and facia plates: included in the scope. 30. Steel for lift machinery: Included in the scope. 31. Servicing and maintenance: Free comprehensive servicing and maintenance should be provided by lift contractor during the guarantee period of one year. 32. Automatic Rescue device: To facilitate the landing of the lift to the nearest floor at the time of power failure. This shall consists of suitable type battery system with charger, invertor, under voltage protection system etc., complete with all accessories. 33. To be provided by the lift contractor with in-built intercom ( push type) in car panel and with provision of push type intercom in machine room and ground floor entrance.

34. Floor annunciator with music with announcement in both Tamil and English. 35. Special features: a. Infra-red door sensor with full height screen b. Voltage stabilizer for circuit control. c. Stainless Steel signal fixtures. d. Vandal proof S.S. Button with S.S. cover e. SS door frames for landing doors. f. VF door operator .g. Call Register signal h. Stainless steel facia plate for car operating panel and landing fixtures. i. On – Off switch for fan and light j. Over load warning indicator with audio announcement 36. Other standard features: Over speed governor, phase failure and phase reversal relay alarm bell, T. Guide brackets for car and counter weight, rubber padding under winding unit, motor of adequate capacity, electro magnetic brake with compression springs car safety gears buffer, electro mechanical door locks emergency key side supporting angles, motor over load protection devices final limit switch main suspension ropes counter weights lifting joint joist for mounting the machineries.

37. Guarantee: Guarantee for the materials and workmanship of equipments complete should be offered by lift firm for a period of not less than one year. 38.Site testing in accordance with IS 14665 should be carried out at the time of handing over. 39. Supply of operation and maintenance manual with necessary tools for operation. 40. Lift licence : Preparation of drawing, payment of charges to CEIG and insurance policies if any and obtaining CEIG safety certificate as per lift act should be done by lift contractor. (Johnson / Kone/ OTIS make)

SRI SURYA CONSTRUCTION

S S Natarajan & Co