ADDN/ ALTN TO TOILET BLDG T-80 AT JAL VIHAR, WIDENING OF STEEL GATE AND CONNECTED WORKS AT NSRY, PROVN OF COVERED SHED AT FMSD, PROVN OF COVERED REFUSE BIN AT BLDG NO P-32 AND CERTAIN MINOR WORKS UNDER GE HADDO, PORT BLAIR

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L for vitrified ceramic coloured tiles ( of approved shade) of size 600 x 600mm, 9 to 10 mm thick in floor set and jointed in neat cement slurry including a layer of screed bed 15mm thick 1:4 and pointed in coloured cement to match the shade of tiles over cement screed bed all as specified and as directed.

All as per item No. 02 but on vertical surfaces such as skirting, dados and riser etc including a layer of screed bed 10mm thick 1:3 all as specified

M & L for 50mm thick plain Cement concrete Type C2 1:3:6 (40 mm graded aggregate) in sub base. complete all as specified and directed.

M&L for 25mm plain cement concrete 1:2:4, type B1 (20mm graded aggregate) as in floors finished even & fair complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and as directed.

S&F in repairs collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets complete all as specified and directed.

S&F in repairs Framed work such as ornamental and intricate design Gate, grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

S & F Rolled sections as in main and cross beams, hip and jack rafters, purlins, pole where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates using structural steel of Fe-410W (Gde E-250 quality A) complete all as specified and directed.

M&L for preparation of new steel surfaces over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed

Cutting holes in brick walls in built in cement mortar or cement lime mortar and stone walls built in lime mortar for inserting holdfasts and and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required exc half brick but not exc one brick complete all as specified and as directed

M & L for roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. and brushing neat cement slurry with 3.0 kg of cement per sq metre complete all as specified and as directed

M&L for preparation of old decorated surfaces of walls and cornices by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salt and trading oil and greasy spots etc and applying one coat of distemper oil emulsion complete all as specified and as directed.

M&L for preparation of old/brick concrete surfaces of walls and cornices by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salt and trading oil and greasy spots etc and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and as directed

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in hard/ dense soil complete all as specified and as directed.

M&L for hardcore of gauge not exceeding 63mm deposited spread and levelled in layers not exceeding 15cm thick watered and rammed to a true surface of broken stone or boulders complete all as specified and directed.

M&L for 100mm thick PCC 1:4:8 type D2 (Using 40mm graded stone aggregate) as in sub base complete all as specified and directed

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design and pattern as in footpath, parks, lawns, drive ways or light traffic parking etc of required strength, thickness and size/shape, made by table vibratory method using PU mould, laid in required colour and pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified

Returning, filling in hard/dense soil including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick complete all as specified and as directed.

Removing excavated material (Soils) to a distance n. exc 50m and depositing where directed at a level n. exc 1.5m above the starting point complete all as specified and directed

M&L precast cement concrete block masonry exc 10 cm width with solid block PCC 1:3:6 type C1 (using 20 mm graded stone aggregate) and setting in cement mortar 1:6 all as specified.

M&L for rendering 15mm thick in CM (1:4) on fair faces of brick work or concrete, surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L for preparation of newly plastered wall surfaces and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and as directed

M&L Reinforced cement concrete (nominal mix) Type B1 1:1.5:3 20mm graded aggregate in slabs supported on walls, beams and coloumns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like beams, cantilevers, bressummers, lintels over 1.5 m span complete all as specified and as directed

M&L Reinforced cement concrete (nominal mix) Type B1 1:1.5:3 20mm graded aggregate in foundations, including rafts, footings, foundation beam, plinth beam, bases for columns etc, basement slabs, under reamed piles and mass concrete complete all as specified and as directed

M&L Reinforced cement concrete (nominal mix) Type B1 1:1.5:3 20mm graded aggregate in Columns, pillars, piers, posts and struts complete all as specified and as directed

M&L Reinforced cement concrete (nominal mix) Type B1 1:1.5:3 20mm graded aggregate in Beams, cantilivers, bressummers, lintels over 1.5m span complete all as specified and as directed

M & L for mild steel TMT bars 10mm dia and over, of grade Fe 500,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L for mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders cut to length, bent to shape required including cranking, bending spirally for hooping ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantlilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc in rough finished surface complete all as specified and directed.

Excavating in post holes (or similar holes) in hard/dense soil each not exceeding 0.5 Cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm watering and removing surplus soil to a distance not exceeding 50 metres and making good disturbed surfaces complete all as specified and as directed.

Excavation in trenches n. exc 1.5m wide and n. exc 1.5m in depth in hard/dense soil for foundation, etc or for shafts, wells, cesspits, manholes, pierholes, etc n. exc 10 Sqm on plan and getting out complete all as specified and directed

M&L for Cement concrete PCC (1:2:4) Type B1 (using 20 mm graded aggregate) as in filling, foundation of posts, railing and similar work and mass concrete complete all as specified and directed.

M&L for mild steel roof trusses (framed), trussed purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., conforming to Fe-410-W (Gde E-250) Quality 'A' complete all as specified and as directed.

S&F Mild Steel work in tubular trusses and tubular posts/ purlins including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS : 1161-1979 grade st-240 including notching, drilling, fitting, riveting and/or welding or connecting with bed plate, bolt and nuts, complete all as specified and as directed.

S&F for mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-410-W (Gde E-250) Quality -A complete all as specified and as directed

S&F for pre painted Galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed.

S&F for pre painted Galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, ridge etc fixed with self tapping screws complete all as specified and directed.

M&L for aluminium wind tie of any size fixed with self tapping screws of size 50/75mm with integral EPDM washer in roof covering complete all as specified and directed.

M&L for Cement concrete 1:4:8 type D2 (using 40mm graded aggregate) as in filling, foundations or mass concrete complete all as specified and as directed by the Engr-in-Charge

Demolition of cement concrete as in block masonry built in cement mortar complete all as specified and as directed.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, exceeding 200mm thick for rough finished surfaces of concrete flat complete all as specified and as directed.

M & L formwork flat or curved to sides of concrete foundations, footings, bases of columns, and plinth beams and similar work vertical or to batter in rough finished surface complete all as specified and as directed.

M & L formwork flat or curved to sides of pillars, posts, struts, piers, columns and stanchions in rough finished surface complete all as specified and as directed.

Dismantling of structural steel of any description not otherwise provided for all as specified.

S&F framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc., to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conforming to Fe-290 Gde E-165 complete all as specified and as directed.

Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design and pattern as in footpath, parks, lawns, drive ways or light traffic parking etc of required strength, thickness and size/shape, made by table vibratory method using PU mould, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand complete all as specified

M & L for cement concrete 1:2:4 Type B1 using 20mm graded stone aggregate in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60cm in height, copings, kneelers, apex stones, bed plates, kerbs as directed.

M & L for 20mm thick Granite (of any type) tiles machine cut, in skirting/dado laid over cement 15mm thick screed CM 1:3 and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete complete all as specified and as directed.

S&F compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc built up from two or more beam or channel sections or angles with plates including all lattice bars, stiffeners, gusset plates confirming to Fe-410-W (Gde-E-250) quality-A complete all as specified and directed.

S&F framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar works conforming to Fe-290, Gde-E-165 all as specified and as directed

S&F welded steel wire fabric n.exc 4 Kg/Sqm to wood or steel members complete all as specified and as directed

M&L for chequered cement concrete tiles of size 30cm x 30cm x 25mm thick with grey cement and pigments set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile as in floor over and including 20mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L precast cement concrete block masonry exc 10 cm width with solid block PCC 1:3:6 type C1 (using 20 mm graded stone aggregate) and setting in cement mortar 1:4 all as specified.

M&L for 10mm thick plaster in CM (1:6) on fair faces of brick work or concrete, surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M & L for preparation of newly plastered surface of wall and applying two coats of white wash complete all as specified and as directed.

M&L for preparation of newly plastered wall surfaces and applying two coat of oil bound distemper over one coat of primer complete all as specified and directed.

M&L for 75mm thick PCC (1:4:8) type D2 (using 40mm graded stone aggregate) as in sub bse of floors complete all as specified and as directed.

M&L for seamless gypsum board false ceiling 12 mm thick including for any sunk or raised moulding with 25mm long self drilling/tapping screws having Philips head with joining compound and 48 mm wide fibre tape to provide seam less finish and including GI frame work of seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flange of 20mm and 30 mm, web of 27 mm, fixed to surrounding wall using nylon sleeves and screws at 450 mm c/c / intermediate channel 0.9 mm thick having two equal flanges of 15 mm suspended from soffit at approx 900 mm c/c with GI cleats and steel expansion fasteners with and including ceiling section (not exceeding 1.2 m length) of 0.55 mm thick having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting across the intermediate channel at 457 mm c/c including hangers 6 mm dia GI adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3 mm size, 60 mm long & expansion hold fasteners 12.5 mm dia, 40 mm long and finally applying two coats of oil bound distemper with roller finish over a coat of primer complete all as specified and as directed.

M&L for coloured glazed ceramic tiles in vertical surfaces such as skirtings, wall, dados and risers to steps etc., using size of tiles 350x250x7mm / 450x350x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with colour of tile with and including 10mm thick backing coat in CM (1:3), complete all as specified and as directed.

M&L for non-skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, as in floors etc, laid over and including 15mm thick screed bed in CM (1:4), set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

Demolition of cement concrete of any description and in any position, sunken floor / roof pading etc not otherwise specifically provided for complete all as specified and as directed.

S&F 20mm outer dia CPVC pipes SDR 13.5 and plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including suitable reducers for 15mm dia complete all as specified

S&F of 25mm outer dia CPVC pipes SDR 13.5 and plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified

S&F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls using synthetic rubber adhesive cement solvent complete all as specified and as directed.

S&F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches using synthetic rubber adhesive cement solvent complete all as specified and as directed.

S&F in repairs PVC (SWR) 110mm dia bend of any radius and jointed with approved adhesive complete all as specified and directed

S&F 75mm bore PVC (SWR) pipes single socketed, in any length pipes single socketed, in any length with rubber ring joints, fixed to walls using synthetic rubber adhesive cement solvent complete all as specified and as directed.

S&F 75mm bore PVC (SWR) pipes single socketed, in any length pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors using synthetic rubber adhesive cement solvent complete all as specified and as directed.

S&F in repairs PVC (SWR) 75mm dia bend with acess door any radius and jointed with adhesive complete all as specified and directed

S&F in repairs PVC (SWR) multi floor trap with grating including jointing with solvent cement, diameter of outlet 75 mm complete all as specified and as directed.

S&F for Second class hard wood (SAL), plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints including preservative treatment complete all as specified and as directed.

S&F for Second class hard wood 30mm thick plain, framed, panelled door shutters (any number of pannels) with of veenerred particle board medium density wood particle boards with commercial face supplied and fitted to chowkats complete all as specified and as directed.

M&L for preparation of new / old wooden surfaces and applying melamine polish through the process of sanding with wood sanding paper of size 60 & 80 and applying wood filler mixed with NCD thinner including applying wood putty on shabby/ nailing area and sanding with sand paper of size 120 and applying sealer and walnut colour stainer ad sanding with sand paper of size 320 and melamine polishing with spray application and again sanding with 400 sand paper and finally applying waxpol (Silicon Make) with soft fine cloth for better shining and finishing complete all as specified and as directed.

S&F 100mm stainless steel butt hinges complete all as specified and as directed.

S&F 150mm stainless steel tower bolts complete all as specified and as directed.

S&F 150mm stainless handles complete all as specified and as directed.

M&L for PVC connections 15mm dia 450m long with 2 Nos PTMT nuts with washer, complete all as specified and as directed.

S&F PVC mirror cabinet of size 330 x 430mm fixed with screw on wall complete all as specified and directed. Make : Prayag Model No.551

S&F in repairs CP cast copper alloy WHB pillar cock long neck with aerator fancy type 15mm bore complete all as specified and directed. Make : Jaquar Cat Part No. CON-021KN or equivalent make of Prayag/Cera.

S&F in repair CP brass hot and cold 15 mm dia wall mixer 3-in-1 system with provision of both hand shower and over head shower composite with 115mm long bend pipe connecting legs & wall flanges complete all as specified and as directed. Make : Jaquar Cat. Part No. CON-281KN or equivalent make of Prayag/Cera.

S&F CP over head shower rose 105mm dia round with revolving joints (with body rotation) and 115mm long shower arm with rabit cleaning system and all fittings complete all as specified and as directed. MAKE: JAQUAR Cat part No. OHS-1709 & SHA-49483 or equivalent Make of Prayag/Cera.

S&F hand shower 100mm round shape single flow (ABS body chrome plated with grey face plate) with rubit cleanig system with easy flex tube in chrome finish 1.5m long with nuts, premium wall bracket for hand shower, 35mm dia and 100mm long round shape complete all as specified and as directed. MAKE: JAQUAR Cat part No. HSH-1937, SHA-571 & SHA-555 or equivalent make as approved.

S&F CP brass 15mm hand shower (health faucet) (ABS body) with 1.5m long easy flexible tube in chrome finish and wall hook complete all as specified and as directed. MAKE: JAQUAR Cat part No. ALD-587 or equivalent make as approved.

S&F toilet paper holder, brass, chromium plated, complete all as specified and as directed. MAKE: JAQUAR Cat part No. ACN-1151N or equivalent in PARRYWARE/ ZOLOTO/ JOHNSON

S&F single towel rail, brass, chromium plated, 600mm long between flanges, fixed in repairs complete all as specified and as directed. MAKE: JAQUAR Cat part No. AQN-7711 or equivalent in PARRYWARE/ PRAYAG/ JOHNSON

S&F soap dish complete all as specified and as directed. MAKE: JAQUAR Cat part No. AQN-7731 or equivalent in PARRYWARE/ PRAYAG/ JOHNSON

S&F two way bib cock, 15mm dia, cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed both ends for iron pipe or for unions, fixed in repairs complete all as specified and as directed. MAKE: JAQUAR Cat part No. CON-041KN, or its equivalent

S&F angular stop cock, 15mm dia, cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed both ends for iron pipe or for unions, fixed in repairs complete all as specified and as directed. MAKE: JAQUAR Cat part No. CON-053KN, or its equivalent

S&F corner glass shelf with brackets complete all as specified and as directed. MAKE: Jaquar Cat part No. ACN-1173 or equivalent in PARRYWARE

M&L for 18mm thick HDF boarding (fire & water proof) as in cup boards exterior grade with one side white lamination and other side coloured prelaminated, size of cabinet as per requirement of the site complete all as specified and as directed. Make: Axis/ Greenply/ Archidply/Bajaj or equivalent Note: Cutting Edges of cupboard shutter/ shelves to be finished with adhesive edge binding tape all as directed

S&F for Powder coated (minimum thickness of powder coating 50 micron) aluminium frame for doors, windows, ventilators and partitions with one or more rebates including jointing cleat for fixing etc complete all as specified and directed.

S&F 4.0mm thick Sheet glass ordinary quality and glazing with aluminum glazing clip in aluminum window/ ventilator shutter not exc 0.5 Sqm in each pane complete all as specified and as directed.

M&L for 75mm thick PCC (1:3:6) type C1 (using 20mm graded stone aggregate) as in plinth protection/ path laid in panels, finish the top surfaces even and smooth complete including filling joints with mastic compound complete all as specified and as directed.

M&L for 20mm thick granite of approved quality machine cut polished bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone as in cooking platform, counter of WHB and like over and includig 15mm thick screed bed in CM 1:4 including grinding and polishing complete all as specified and directed.

S&F vitreous china wash down water closet pan (pedestal pattern cascade type) standard size with 'S' or 'P' trap and other connecting items approved brand including fixing with white cement complete all as specified. Make : Jaquar (Cat part No : LYS WHT 0314) or equivalent make as approved.

S & F vitreous China wash hand basin, white, oval shape of size 550mm x 400mm including cutting for, 32mm CP waste coupling chain and plug, waste fitting and all necessary inlet, outlet connection complete all as specified and as directed.

Taking down copper/aluminium point wiring(light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

Taking down old aluminium sub main wiring of any size complete all as specified and directed.

Taking down fuse Unit/DBs with MCB/MCCB 415 Volt/230 Volt complete all as specified and directed.

Taking down existing light fittings of any type complete all as directed

M&L for Point wiring complete as specified with 1100 volt grade 1.5 sqmm. (nominal area) single core PVC insulated unsheathed cable multi stranded copper conductor drawn through and including rigid non-metallic PVC conduit concealed of suitable size but not less than 20mm dia, with all fittings, fixed in wall/ ceiling/ floor including decorative modular cover plates (inner and outer) suitable for housing modular pattern switches/ sockets/ regulators etc. along with necessary metal boxes flush mounting in the wall duly earthed with same cable as for wiring above but green in colour as continuous earthing wire complete all as specified for the following :- Make of wire :- Polycab/ Gloster/ Anchor/ Havells/ Finolex/ and Make of PVC Casing & Caping /Conduit : Modi/ Precision/ Supreme/ Finolex/ Polycab.

ONE LIGHT/FAN point controlled by one, one way 6 Amps switch.

Point wiring for 3 pin switch socket outlet, 6Amps on independent board

Point wiring for 3 pin switch socket outlet, 6Amps on same board

M&L for Point wiring complete with 4 Sqmm (nominal area) single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor (with colour coding of Red/Blue/Yellow for phase and Black for neutral), drawn through and including rigid non metallic PVC conduit concealed of suitable size (not less than 25mm) and accessories fixed in walls/ceilings etc., including provision of PVC insulated 4 Sqmm FRLS cable with copper conductor green in colour for earth continuity and connected to common earth dolly and sunk in CI boxes/pressed steel terminal boxes 60mm deep made out of 1.6mm thick MS sheet duly painted with two coats of anti-corrosive paint outside and with two coats of aluminium paint inside and including decorative modular cover plates (inner & outer) suitable for housing the modular pattern switches, socket outlet etc, all as specified and as directed for ONE 15A SOCKET OUTLET point controlled by one, one way 15 Amps switch on independent board.

S&F modular switch, one way, one module, single pole, 6 Amps, 230 Volts AC complete all as specified and as directed. Make: Roma (Anchor) / Havells/Simens / Legrand

S&F Switch modular type, flush type, single pole one way 16 amps all as directed. Make : Anchor/Cona/Legrand

S&F socket outlet, modular type, 1 way 6 Amps, 3 pin flush type 230 Volts AC circuit complete all as specified and as directed. Make: Roma (Anchor) / Havells/Simens / Legrand

S&F socket outlet 2 in 1, 3 pin 6/16Amp, flush type, universal all as directed. Make: Roma (Anchor) / Havells/Simens / Legrand

S&F and testing surface tube light fittings LED 10 watts 2 feet including all accessories and fixing arrangements for fixing the light fitting complete all as specified and as directed. Make : Luker Cat Part No : LT510P or equivalent to CG/Philips/Havells

S&F and testing surface tube light fittings LED 20 watts 4 feet including all accessories and fixing arrangements for fixing the light fitting complete all as specified and as directed. Make : Luker Cat Part No : LT5M20 or equivalent to CG/Philips/Havells

S & F air ventilating fan 250mm sweep single ph, 230 volt PVC body with louvers incl all fixing arrangement complete all as specified and directed Make:- Havells, model No. FHVVEDXOWH10 Venti Air DX or CG, Model No. BRISK AIR NEO or equivalent to Orient / Usha/ Khaitan

S&F energy efficient 25 Litre capacity instant with 2KW water heater, BEE 5 Star rating, vertical, installed complete including flexible pipe for hot and cold water, pressure release valve, anchor fastener 4 Nos of suitable size complete all as specified and as directed. Make : Havells Model No : MONZA DIGI or equivalent of Racold / Bajaj / CG/ USHA

M&L for Sub main wiring complete with two runs (1P+1N) of 4.0 Sqmm single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor (with colour coding of Red/Blue/Yellow for phase and Black for neutral) and one run of 4.0 Sqmm single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor as earth wire green in colour including lugs, drawn through and including rigid 25mm dia PVC conduit and conduit accessories concealed in wall/ceiling/roof/ floor complete all as specified and as directed. NOTE: Two runs of 4.0 Sqm copper conductor, One run of 4.0 Sqmm copper conductor as earth wire and one run of PVC conduit shall be measured as one unit length.

S & F single pole and neutral sheet steel powder coated distribution board IP-43 protection with door eathing for MCBs fitted with 200 Amps rated bus bar, neutral link, earth Bar and din rail suitable for use on 240 Volts , 50 Hz supply double door SP&N DB system 4 ways, including taking down old u/s DB of any type /rating and making good to the disturbed surface/walls. Make : C&S/Indo Asian/Havells/L&T/Legrand

S&F MCB, SPN, "C" series, 40 Amps, having current rating 10 KA complete all as specified and as directed. MAKE: C&S/ Indo Asian/Havells/L&T

S&F MCB, single pole 6 to 32 Amps, "C" series, having current rating 10 KA complete all as specified and as directed. MAKE: C&S/ Indo Asian/Havells/L&T

Earthing complete with galvanised earth plate electrode 60 cm x 60 cmx 6.15 mm thick, buried directly in ground vertically (earth pit not less than 2.25 m deep below ground level) with top edge of the earth plate not less than 1.5m below ground level , connected to GI earth wire 4 mm Dia as earthing lead by means of bolts and nuts check nuts and washers of galvanized iron and connected to main switch board including watering arrangements with PCC chamber (1:2:4 Type B1), MS funnel with wire mesh,. CI cover with frame etc including necessary excavation in any type of strata , returning, filling in, removal of surplus soil outside MD land ,filling of charcoal and salt complete all as shown in Ectrical Plate No. 3 of MES Sch Part I , connected to Earthing test point all as specified and directed on testing on completion.

Sree Tirumala Enterprises

CARTWHEEL CONSTRUCTION

LOOK UP ENTERPRISES

V KARTHICK

CHANDER SEKER ENTERPRISE

SHUBHAM SHANKAR GAIKWAD

Bismi Builders & Enterprises

M/s Ramesh Lal