Repair and Maintenance work arrangements at Corporation Officer Quarters 50-3 and Commissioner Camp Office East Side compound wall in Ward No.31.

Amount

Clean removal of cement plaster from walls and racking out joints 20mm deep etc Complete

Plastering with cement mortar (1:5) 20mm thick in all floors including cost and conveyance of all materials to site and labour charges etc, complete complying with standard specifications (S.I.309)

Dismantling, clearing away and carefully stacking materials useful for reuse for any thickness of walls Brick / stone masonry in Cement mortar walls under 3 m high etc Complete

Dismantling RCC by manual/ by using deploying machineries Etc Complete

Brick work in CM 1:5 (one cement & Five sand) using II class ground moulded bricks of size 9"X43/8"X 23/4" standard specification including finishing, curing, etc., complete complying with standard specification - Ground floor

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. - For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

Reinforced Cement concrete 1:1.5 :3 (one cement, one and half sand & three course aggregate) using 20mm gauge hand broken/ and broken granite stone for all RCC items of works excluding centering shuttering and cost of reinforcement but including curing etc.,complete and also including fixing fan clamps and fixtures in rcc works wherever necessary as directed by departmental officer etc., complete.

Suppling and fabricating and placing in position MS (or) R.T.S. bar for reinforcement to all RCC works as per the design given including cost of steel and binding wire also in all floors as per standard specification.

Plastering with cement mortar 1:5, 12 mm ,thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications (S.I.306)

Weathering Course with Concrete Broken Brick (S.I.No.278) & ( P & D) Data 54.Jelly 20mm gauge in pure slaked lime (no sand to be added) over roof slab,the proportion of brick jelly to lime being '32:12.5 well beated with wooden beaters for giving required slope and thickness as directed by the departmental officers etc., complete as per standard specification.

Finishing the top of roof with one course of machine pressed tiles of size 200 mm x 200 mm x 20 mm of approved quality in Cement Mortar 1:3 (One Cement add three sand) 12 mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete as per standard specification.

Dismantling, clearing away and carefully stacking materials useful for reuse for any thickness of walls Floor finish and dadooing walls in Cement Mortar with mosaic tiles/ glazed tiles/ cuddapah slabs etc Complete

Plain Cement concrete 1:4:8 (one cement, four sand, eight aggregate) using 40mm gauge hand broken granite stone jelly for foundation including dewatering if found necessary and laid in layers of not more than 15cm thick and compacted, etc., complete complying with standard specfication.

Paving the floor with Double charged Vitrified tiles of approved quality and colour of size 600x600x8mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officer. The colour & quality of tiles should be got approved by Municipal Engineer before use on work

Dadooing walls with Glazed tiles of sizes 305mm X 200mm X 6mm size of approved make and quality and colour Set in cement mortar 1:2 (One part of Cement and two part of Plastering Sand (P Sand)) over 10 mm base layer plastering and pointing with white cement neatly as directed

Construction of inspection chambers of following sizes with earth work excavation for foundation , 23cm thick concrete bed using 40mm brick jelly concrete in cm 1:4:8 for foundation , brick work in cm 1:6 for chamber , plastering with cm 1:3 , 12mm thick , benching , channelling , supplying and fixing 45X45cm medium weight L.S cover and frame etc.complete.., (Size 60 x 60 x 60)

Painting old wall surface with One coat of Plastic Emulsion paint of approved quality including cleaning of plaster surface with soap soda and water by manual labour.

Painting old wood work with one coat of Synthetic Enamal paint of approved quality including cleaning the old surface by mannual labour.

Painting One coats with Ready Mixed Enamel Paint over the Old iron works of approved quality and colour without priming coat including the cost all materials etc.,complete, in all floors.

Providing for all floors mixed with red oxide including cost and conveyance of all materil as to site and labour charges etc, complete as per standard specifications (S.I.306)

Supply & Fixing of PVC Pipes & Specials 20 mm PVC Pipe

20mm PVC Elbow

20mm PVC Tee

110mm PVC Pipe

110mm PVC Tee

110mm PVC Elbow

75mm PVC Pipe

75mm PVC Elbow

SS Heavy Duty long body tap 15mm

CP Shower Arm with Overhead shower rose

25 mm PVC Pipe

25mm PVC Elbow

25mm PVC Tee

25mm PVC Coupler

25mm x 20mm Reducer

25mm GM Gate Valve

65mm diaGM Gate Valve

Wiring with 2 x 1.5sq.mm. PVC insulated single core unsheathed FRLS copper conductor cable of 1100V grade insuitable heavy gauge MS conduit pipe on wall and ceiling with MS accessories in flush with wall with 150mm x100mm x75mm MS switchbox with 3mm thick hylum sheet cover for 5A3 pin non interlocking CS plug with continuous earthwire connection of 1.5sq.mm copper wire and making good of the concealed portion with suitable colour for concealed plugpoint

Supply and fixing of 1200mm (48") sweep AC ceiling fan complete with stepped electronic 300W regulator with 1metre down rod with fan clamp with side plates and cross arm of size 450mm (18") Etc Complete SD 107

Supply and Fixing for LED OUTDOOR FITTINGS (LIGHT EMITTING DIODE) HIGHER END etc Complete 30W LED Street Light Fitting with LED

Supply and Fixing for 20W LED Tube Light for T8 Fitting (Single Side) M-1278 etc Complete

Supplying and fixing in position White / Colour Glazed Model Floor Mounted European Water Closet of best quality and approved make with 100mm P or S trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using indian adopter joint including all internal fittings, such as, 15mm bras connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and redoing the dismantled masonry to original condition, etc., complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Executive Engineer before use on works) Floor Fitting

Supply and fixing of PVC Solid Doors using 19gauge 19mm MS Sq,tubes for styles and frames, 15mm MS Sq.tubes for to, Lock and bottom rails. The Steel Tubes shall be covered with 5mm thick Solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including furniture and fittings. The over all size of styles shall be 50mm X 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm X 30mm. The over all size of frames shall be 50mm X 45mm with suitable tabate for housing the shutter etc, complete as per standard specification

Supplying, fabricating and fixing in position of Alumi.Anod.natural colour matt finish door half glazed and half PLB board using 12mm thick PLB board and 5.5mm thick glazed door using rectangular Alu.Box section of following sizes for frame and shutter with necessary accessories such as rubber beading, Al. Clips, Best double action floor springs, Aluminium Handles on bothsides, floorstopper, Tower bolt, Locks and glass including all materials ,Labour ,power consemption charges required for fabrication if necessary chipping, dismantling making necessary holes in RCC Coloums, Beams or Masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing etc., complete. The Alumi. surface must be anodised with matt finish under electrically controlled condition inaccordance with IS specification 1868/1962 of Anodicfil thickness of not less than 15 Microns (Fifteen) for all sections.

Supplying & fixing door shutters for Solid Core Flush Shutters with Teak ply on both side with teak wood lipping alround 35mm thick, single leaf confirming to IS:12406/1989 with 35x12mm T.W. Lipping on all edges with necessary adhesives and CP screws complying with standard specifications. The rate is inclusive of threee coats of best quality varnish but excluding cost of furniture fittings, such as 300 mm tower bolt 2nos, 200mm towerbolt 1 No. 300mm Aldrop 1 No. Alu handle ornamental type 2 Nos and 1No. Door stopper etc complete.

Supplying and fixing of S.S Sink of size 600mm x 450mm x 200mm etc Complete

Supply and Fixing fot Automatic Electrical Water Heater with copper container, with Glass Wool / Puf Insulation with MS powder coated shell suitable for 25 Litres capacity 230V / 1000W (Higher End)

Supply and Fixing for AC Exhaust Fan 300mm (12”) Sweep (Heavy Duty) etc Complete.,

Fabricating, Supplying and fixing M.S.Pipe Posts for Chain Link-2" x2" using 10 Gauge Galvanized Iron Wire (of all sizes) Chain Link fencing of size 80mm MS Pipe Below ground level of 60cm and above ground level of 2.40m including cost of steel and binding wire and laying cement concrete 1:2:4 20mm size etc Complete.0

Supply and delivery of Electric Monoset centrifugal pump conforming to IS 9079:2002 as amended from time to time, with CI FG 200 Casing, hydraulically and dynamically balanced Bronze grade LTB-2 impeller, impeller ring and casing ring, stainless steel shaft capable of discharging required quantity of water against a total head noted below due to all causes. Pump shall of BEE 3 Star Rated and capable of discharging the specified quantity at the head noted at the minimum NPSHA at site conditions. The shut off head shall be atleast 25% over and above the head at duty point. The pump shall be suitable for operation in AC three phase , 415 V+/- 10% , 50 Hz +/- 5%. Squirrel cage induction motor for continuous operation. The speed of the Pump and Motor shall be not less than 2700 to 2900 RPM respectively.WD-M1555

Add GST 18%

A.M.CONSTRUCTION (BID ID -1552434)