WBHD/EE/ED-1/eNIT-244/2025-26

PART-A:Charges for lifting of 5 H.P. (K.S.B.) make Submersible pump motor set with column pipes from the existing tubewell after dis-connecting the plumbing line and electrical connection with the help of spl. type tools & tackles & Chainpully block on tripoid stand.

Charges for opening out the 5 H.P.(K.S.B.) make submersible Pump motor set part by part and all its components and refitting the same after changing the necy. spares & parts.

Charges for complete dismentling the winding of 5 H.P. submersible motor inclu. S & F new-winding with P.V.C. coated copper wire inclu. internal connection and cable complete as per G.S.

Supply & fixing top and bottom bush.

Supply & fixing the roter sleeve bush.

Charges for grinding and polishing of the motor roter shaft.

Charges for new thrust bearing complete set [Upper thrust plate, lower thrust plate, inside bearing, non metallic fiber pad, thrust liner V-6]

Supply & fixing the discharges head bush.

Supply & fixing neck ring.

Supply & fixing Suction cover bush.

Supply & fixing coupling key with diffuser for pump.

Supply & fixing new PVC impeller in place of new one.

Charges for grinding & polishing the pump shaft.

Painting the pump motor set with 2 (two) coats of approved paints over one coat of R.O. primer.

Complete testing, checking and meggering the pump motor set before installing it in the bore well.

Supply & fixing 50 mm dia GM gate valve [Make Leader/Laxmi/Zoloto]

Carrying charges for pump motor set from work site to Co.'s workshop and Co.'s workshop to back after repairing (Up & down).

Part-B Lowering & Installation of new 5 HP Submersible Pump Motor set in a deep tube well [KSB - Make ] by company's won tools and tackles

Supply of 5 HP submersible pump motor set capable to discharge 600-200 LPM of sand free clean water of head 20- 47 Mtr. direct coupling with wet type winding Motor, running as 3 ph, 415 v, 50 HZ, 2900 RPM, with cast iron stage bowel, bronze impeller, stainless steel shaft with top outlet 65 mm, 5 H.P. ' KSB - make, Model No.BPD242 04+UMAI 150 - 3/22 - 1:5 SQMM DOL, 4 stage (Make - KSB/ Kirloskar /CG)

Supply and fixing of following Gl specials incl. all jointing materials for (Header Assembly)S&F 50 mm dia GI union (ISI)

S&F 50 mm dia GI short piece (ISI)

S&F 50 mm dia GI elbow (ISI)

S& 50 mm dia GI socket (ISI)

S& 50 mm dia Gl tee (ISI)

S& 50 mm dia reducing socket (ISI)

S& 50 mm dia Hex Nipple (ISI)

Re - Jointing header assembly by co's labours,tols and tackles etc. after installation the pump motor set.

supply and fixing new gasket for flange.

Supply and fixing of 50 mm dia column pipe conforming IS 1239 (I)[Make- Jindal/Tata]

S&F MS body safety clamp for hanging P/M set with rope.

S & Laying of 1.1 KV Gr. 2.5 sq,mm flat submersible cable. [Make - Finolex / KEI / Gloster]

Supply and fixing of DOL starter relay range 9-14 amp [Make - LaT, Mul type with MU relay, Cat No. : SS96647 DOAO / Havells/ABB.

Transportation charges for carry pump motor, pipe with all accessories tools, tackles, and tripoid stand etc. from Co's work shop to work site and back.

Painting the header line with 2 coats of RO Primer

Part - C Charges for lifting of 6 H.P. (K.S.B.) make Submersible pump motor set with column pipes from the existing tubewell after dis- connecting the plumbing line and electrical connection with the help of spl. type tools & tackles & Chainpully block on tripoid stand.

Charges for opening out the 6 H.P.(K.S.B.) make submersible motor part by part and all its components and refitting the same after changing the necy. spares & parts.

Charges for complete dismentling the winding of 6 H.P. submersible motor inclu. S & F new-winding with P.V.C. coated copper wire inclu. internal connection and cable complete as per G.S

Supply & changing top and bottom bush.

Supply & changing the rotor sleeve bush.

Charges for grinding and polishing of the motor rotor shaft.

Complete repairing thrust bearing assembly including supplying & fixing of clatch liner and clatch plate with bolts (V-6).

Charges for opening out the pump part by part and all its components and refitting the same after changing the necy. spares & parts.

Supply & changing the discharges head bush.

Supply & changing the runing casing bush.

Supply & changing the shaft protection sleev bush.

Supply & changing the Neck Ring.

Supply & changing the Suction Cover Bush.

Supply & changing the Key of Pump.

Matalizing the worn out portion of the impeller and machining the same.

Charges for turning & polishing the casing for pump.

Charges for grinding & polishing the pump shaft.

Supply and installation of 440 Volts 2900 R.P.M. 6 Н.Р. submersible pump motor set (Make - K.S.B.) Model No.- BPD 242/5A + UMAI 150 - 4/22 into the tubewell incl. errection of tripoid stand by co's own tools & tackles. (Approval make)

Charges for jointing 3 core, 2.5 sq.mm. flat submersible cable with S/F necy. Water insulating tape.

S/F the followings (i) 80 mm dia G.I. Reducing Socket (Make - Cyma).

(ii) 80 mm dia G.I. Socket (Make - Cyma).

(iii) 80 mm dia G.I. Hex Nipple (Heavy).

(iv) 80 mm dia Rubber insertion cloth.

(v) Nuts & bolts with washer.

Through checking & cleaning the pannel board including starter and main switch including S/changing nut & bolts etc. as direction of E.I.C

Painting the pump motor set with 2 (two) coats of approved paints over one coat of R.O. primer.

Carrying charges for pump motor set from work site to Co.'s workshop and Co.'s workshop to back after repairing (Up & down)

Part- D Charges for lifting of 7.5 H.P.(K.S.B) make submersible pump motor set with column pipe from the existing tubewell after disconnecting the plumbing line and electrical connection and re- installation of same 7.5 H.P. (K.S.B) make submersible pump motor set after repair into the tubewell and commission after connecting the plumbing line and electrical connection incl. removed and refixing by co's own tools and tackles and Chainpully block on tripoid stand.

Charges for Withdrawing of 5 H.P.(Kirloskar) make monoblock submersible pump motor set from 15'ft depth U.G. reservoir incl. dis-conneccting the plumbing lines and electrical connection with the help of spl. type tools & tackles.

Supply & installation of 5 H.P. (440V) 2900 R.P.M. monoblock submersible pump motor set (Make - Kirloskar.) by tools & tackles & manual labour. (Model No. - KOS-538+) KSB/CG). KSB/CG).

Charges for opening out the submersible motor part by part and all its components and refitting the same after changing the necy spares & parts.

Charges for complete dismentling the winding of submersible motor inclu. S & F new-winding with P.V.C. coated copper wire inclu. internal connection and cable complete as per G.S. (a) 7.5 HP.

Supply & changing the top and bottom bush.

Supply & changing the rotor sleeve Bush.

Charges for turning and polishing of the motor roter shaft.

Complete repairing thrust bearing assembly incl. supplying & fixing of clatch liner and clatch plate with bolts (V-6).

Charges for opening out the pump part by part and all its components and refitting the same after changing the necy. spares & parts.

Supply & changing the discharges head bush.

Supply & changing the shaft protection sleev bush.

Supply & changing runing casing bush.

Supply & changing neck ring.

Supply & changing key for pump.

Supply & changing the body paper gasket for pump.

Charges for turning and polishing the casing for pump.

Charges for turning and polishing the pump shaft.

Matalizing the worn out portion of the impeller and machining the same.

Supply, installation, fitting and fixing 80 mm dia 3 mtr length UPVC Column pipe standard class. (Make-Oriplast).

S&F of 80 mm dia. C.I. Adapter.

S&F of nylon rope.

S&F 2.5 sq.mm. 3 core flat copper P.V.C. coated copper submersible motor cable (Make-Finolex).

Charges for jointing 3 core, 2.5 sq.mm. flat submersible cable with S/F necy. Water insulating tape.

S&F of 80 mm dia. Rubber insertion cloth.

S&F of 5/8" x 2.5" nuts & bolts with washer.

Through checking & cleaning the pannel board including starter and main switch including S/changing nut & bolts etc. as direction of E.I.C

Painting the pump motor set after Scraping out the old paints over one coat of R.O. Primer and 2 (two) coats of approved paint

Carrying charges for pump motor set from work site to Co.'s workshop and Co.'s workshop to back after repairing including loading & unloading (Up & down).

Add. G.S.T.@ 18% (on Total from item no 1 to 91) to be calculated by bidder

Add. LWC.@ 1% to be calculated (on total from item no 1 to 91 + GST@18%) by bidder

Please Enable Macros to View BoQ information