IRSHUPSP/PAL/04

Amount

Earth work excavation for foundation with all intial leads and lifts in all soils and sub soils and to the required depth as may be directed except hard rock requiring blasting inclusive of shoring, strutting and bailing out water wherever necessary including refilling the sides of foundation with excavated earth , depositing the surplus earth in places shown and levelling the site with all leads and lifts etc., complete in all respects as directed by the departmental officers. Initial lead of 10m and initial lift of 2m

Earth work excavation for foundation with all intial leads and lifts in all soils and SDR to the required depth as may be directed except hard rock requiring blasting inclusive of shoring, strutting and bailing out water wherever necessary refilling the sides of foundation with excavated earth in layers of not exceeding 15cm thick well consolidated depositing the surplus earth in places shown and levelling the site with all leads and lifts etc., complete complying with standard specification.

Initial lead of 10m and initial lift of 2m

Initial lead of 10m and additional lift of 1m

Initial lead of 10m and additional lift of 1m

Earthwork excavation for foundation in all soils and subsoils and to the required depth as may be directed except hard rock requiring blasting inclusive of shoring, strutting and bailing out water wherever necessary depositing the surplus earth in places shown and levelling the site with all leads and lifts etc., complete in all respects as directed by the departmental officers bed width 1.25m and below

Open Earthwork excavation for foundation in all soils and subsoils and to the required depth as may be directed except hard rock requiring blasting inclusive of shoring, strutting and bailing out water wherever necessary depositing the surplus earth in places shown and levelling the site with all leads and lifts etc., complete in all respects as directed by the departmental officers.

Initial lead of 10m and initial lift of 2m

Initial lead of 10m and additional lift of 1m

Initial lead of 10m and additional lift of 1m

Initial lead of 10m and additional lift of 1m

Initial lead of 10m and additional lift of 1m

Filling in foundation and basement with filling M-sand in layers of not exceeding 15 cm thick well watered, rammed and consolidated complying with relevant standard specification including the cost of supplying filling m-sand etc., complete in all respects as directed by the departmental officers.

Filling with river sand in layers of not exceeding 15cm thick well consolidated including the cost of supplying river sand, etc complete in all respects as directed by the departmental officers.

Filling in foundation and basement with Quarry dust in layers not exceeding 15 cms thick well watered rammed and consolidated including the cost of supplying of quarry dust etc., complete complying with standard specification and as directed by the departmental officers.

Refilling with excavated earth other than sand in foundation and basement including spreading in layers not exceeding 15cm thick, well- watered, rammed and consolidated by hand ramming, etc., complete complying with standard specification.

Filling the low lying area with good quality gravel in layers not exceeding 15 cm thick including collection, conveyance and stocking for premeasurement including consolidation by the power roller, labour charges for power roller etc complete complying with standard specification.

Filling the foundation and basement with good quality earth conveyed from any source outside the scheme area with a lead of 12 KM including cutting the earth, loading, spreading and consolidation etc., complete complying with standard specification.

Cement concrete 1:4:8 (one of cement, four of M-Sand and eight of hard broken stone jelly) using 20mm size hard broken stone jelly for foundation inclusive of shoring, strutting, bailing out water, ramming, curing, etc complete complying with standard specification.

Cement concrete 1:2:4 (one of cement, two of sand and four of hard broken stone jelly) using 20mm size hard broken stone jelly for foundation inclusive of shoring, strutting, bailing out water, ramming, curing, etc complete complying with standard specification.

Providing and laying the READY MIX CONCRETE of M25 Grade using Ordinary Portland Cement with a minimum cement content of 370 kg/m3 with water cement ratio not exceeding 0.45 including the use of plastizer of approved make and dosage of required grade, laying in position at all locations and levels using 20mm size and down graded ISS HBG aggregates in all types of works, cost of sand of approved quality including hire charges for pump and pumping charges to the required location, machine vibrating, pumping, curing, providing fixtures like fan clamps etc., as required excluding cost of reinforcement and fabrication charges, centering and shuttering, mix details to get approved before commencement of the work adopting pour card system as per IS 456 / 2000 wherever necessary as directed by the departmental officers etc., complete in all respects (All floors)

Providing form work for centering, shuttering etc., for all reinforced concrete work such as plinth beam, raft beam, raft slab, grade beam etc., including strutting and shuttering wherever required using MS sheets of suitable size of BG 10, stiffened with MS angle of size 25mm x 25mm x 3mm laid over silver oak (Country wood) joists of size 10cm x 6.5 cm (Spaced about 91cm center to center) distance and supported by casurina props of size 10cm-13cm dia (spaced at 75 cm center to center) and removing the same after a specified period without damaging RCC works in all floors etc., complete in all respects as directed by the departmental officers. For Grade Beam, Plinth beams,Column Footings etc..,

Providing form work for centering, shuttering etc., for all reinforced concrete work like slab, beams, lintels, loft etc., including shuttering, upto 3.00m high using MS sheet of size 90cm x 60cm and BG 10, stiffened with MS angle of size 25mm x 25mm x 3mm laid over silver oak (Country wood) joists of size 10cm x 6.5 cm (Spaced about 91cm center to center) distance and supported by casurina props of size 10cm-13cm dia (spaced at 75 cm center to center) and removing the same after a specified period without damaging RCC works in all floors etc., complete in all respects as directed by the departmental officers. For slabs, lintels, beams etc.,

Providing form work for centering, shuttering etc., for all reinforced concrete work like lintels, window boxing etc., including shuttering, upto 3.00m high using MS sheet of size 90cm x 60cm and BG 10, stiffened with MS angle of size 25mm x 25mm x 3mm laid over silver oak (Country wood) joist of size 10 cm x 6.5 cm (spaced about 91cm centre to centre) distance and supported by casurina props of size 10cm to 13cm dia (spaced at 75cm centre to centre) and removing the same after a specified period without damaging RCC works in all floors etc complete in all respects as directed by the departmental officers. For Sunshades,columns, window, boxing etc.,

Supplying, fabricating and placing the following kinds of steel grills Fe 500 D grade steel reinforcement bars as per IS 1786 : 2008 for all reinforced cement concrete works such as plinth beam, lintels, beams, sunshade, roof in position and floor slabs etc., including cost of steel and fabricating the reinforcement grills in position etc., complete in all floors (The rate including the cost of binding wire steel also)

Brick work in cement mortar 1:5 (One of cement and five of sand) using flyash bricks of size 230 x 110 x 70mm including dewatering wherever necessary, proper setting and curing etc,. complete complying with standard specification and as directed by the departmental officers. In Foundation and basement

Brickwork in cement mortar 1:6 (One of cement and six of sand) using Fly ash bricks for super structure in the following floors including fixing the frames of doors and windows scaffolding, proper setting curing etc complete complying with standard specification and as directed by the department officers In Ground Floor

Brick partition walls 11 cm thick using Fly ash bricks in cement mortar 1:5(One of cement and five of sand) in the following floors including fixing the frames of doors and windows and scaffolding proper setting, curing, etc., complete complying with standard specification and as directed by the department officers.

Masonry work using Autoclaved Aerated cement blocks of size 600 x 200 x 200 mm in cement mortar 1:6 (one of cement six of M-sand) for super structure in all floors including fixing frames of door and windows, proper setting curing etc., complete complying with standard specification as directed by the departmental officers.

In Ground Floor

In First Floor

In Second Floor

In Third Floor

In Fourth Floor

Masonry work using Autoclaved Aerated cement blocks of size 600 x 200 x 100 mm in cement mortar 1:5 (one of cement five of M-sand) for super structure in all floors including fixing frames of door and windows, proper setting curing etc., complete complying with standard specification as directed by the departmental officers.

In Ground Floor

In First Floor

In Second Floor

In Third Floor

Brick Partition wall 7.5cm thick in cement mortar 1:5 (one of cement and five of M-Sand) using Fly Ash bricks of minimum size 23cmx11cmx7.5cm including fixing the frames of doors and windows, scaffolding and proper setting, curing, finishing etc., complete complying with standard specification and as directed by the departmental officers

In Ground Floor

In First Floor

In Second Floor

In Third Floor

Providing 7 cm thick stair case parapet wall using Fly ash Bricks of size 230×110×70mm in cement mortor 1:4 (one of cement and four of M-sand ) and plastering the hand rail portion only with red oxide plastering in cement mortar 1:4 (one of cement four of M-sand) 20mm thick using 9.80kg of red oxide powder per 10m2 and plastering either side of parapet with cement mortar 1:4 (one of cement and four of M-sand ) 20mm thick including providing skirting, finishing smooth in all floors etc., complete in all respects as directed by the departmental officers.

Plastering with Cement mortar 1:4 (one cement and four of plastering sand) 20mm thick with necessary water proofing compound at the rate of 1.06 kg per 10m2 including finishing smooth, setting, curing etc., complete complying with standard specification and as directed by the departmental officers.

Plastering the top of flooring with cement morter 1:4, (One of cement and four of P-Sand) 20mm thick including finishing smooth, setting, curing etc., complete complying with standard specification and as directed by the departmental officers.

Plastering the top of flooring with cement morter 1:3, (One of cement and three of sand) 20mm thick with water proofing compound including finishing smooth, setting, curing etc., complete complying with standard specification and as directed by the departmental officers.

Plastering the walls with cement mortar 1:5 (One of cement and five of P-sand) 12mm thick including scaffolding, finishing smooth, setting, curing etc., complete in all respects as directed by the departmental officers.

Special ceiling plastering and finishing the exposed surface of all RCC works in cement mortar 1:3 (One of cement and three of P-Sand) 10mm thick including hacking the RCC surface, providing necessary water band using the same mix of mortar wherever necessary proper finishing, curing, scaffolding etc., complete with relevant standard specification as directed by the departmental officers.

Stucco plastering of CM 1:3 12mm thick using blue granite chips of size 10mm and below over the existing base plastering with cement mortar 1:5, 12mm thick, etc., complete complying with standard specifications as directed by the departmental officer.

Cement concrete 1:5:12.5 (One of cement, five of M-Sand and twelve and half of hard broken brick jelly) using 20mm size broken brick jelly including laying, ramming, curing finishing, etc. complete complying with standard specification and as directed by the departmental officers

Providing Ellis Pattern flooring 20mm thick (Ellis pattern) with layer of cement concrete 1:3 (one of cement and three of hard broken stone) (No sand) using hard blue granite chips of size 3mm to 10mm and surface rendered smooth over RCC slab including supplying and fixing 20mm dia GI pipe outlet etc., complete in all respects as directed by the departmental officers.

Flooring with stainfree Nano Polish vitrified tiles of size 600mmx600mmx8mm of approved quality in cement mortar 1:3 (one of cement and three of M-sand), 20mm thick laid straight alignment and pointed neatly with colour cement @ 0.40kg/m2 laid with out any gap in the tiles neatly and fixing in position as per the std.specification and etc.complete in all respects as directed by the departmental officers.

Dadooing the walls with First quality colour glazed design tiles of size 15cm x 15cm x 6mm of approved quality and make and laid in cement mortar 1:2 (one of cement and two of M-sand), 10mm thick and pointing with white cement using 0.40kg/m2 including finishing the joint and pointing flush with tile surface etc., complete in all respects as directed by the departmental officers.

Flooring with ceramic tiles of approved quality and colour of size 305mm x 305mm x 6mm thick as per IS 13712 : 1998 laid over 20mm thick cement mortar 1:3 (one cement and three m-sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.30kg/m2 etc., complete complying with standard specification and as directed by the departmental officers.. (The make and brand of tiles should be got approved by Executive Engineer before use on works)

Supplying and fixing in position of cuddappah slab of 20 mm thick both sides polished for cup-board planks of required size including cost of slab, labour charges for cutting and fixing into walls etc., complete in all respects as directed by the departmental officers.

Supplying and fixing of Door of following sizes using CRCA pressed steel box section 18 gauge or 1.25mm thick for door frames of size ~100mmx75mm, with groove of size 30mmx20mm for resting the door shutter and chamfer finish at front and supplying and fixing solid core flush shutter with teak ply on one side and commercial ply on other side with teak wood lipping around of 35mm thick including providing holes and fixing wooden blocks for fixing fixtures and fittings including cost of 6 nos of hold fast using the iron angle of 15cm length with split ends, 4 nos of butt hinges, 2 nos of 150mm tower bolts with receiver, 1 nos of 300mm tower bolts with receiver, 1 no of 300mm Aldrop and 2 nos of handle with necessary screws including one coat of red oxide primer etc., complete as directed by the departmental officers.

1000mm x 2100mm

900mm x 2100mm

1830mm x 2100mm

Fabrication, supply and fixing of M.S Door of overall size 910mm × 1980mm with MS angle frame for three sides using angle of size 35mm × 35mm × 5mm (IS 808 - 1989) using the same angle for hold fasts (6 nos of 200mm long), MS flat for bottom side using flat of size 32mm × 6mm with suitable door shutter (single leaf) using 22 gauge GI sheet (IS 277 - 1992) and MS angle frame alround using the angle of size 25mm × 25mm × 3mm (IS 808 - 1989), shutters with single leaf with stiffeners 200mm width at top, middle and bottom at rear side of the shuter, vertical grooves (dumpling - machine pressed) of 25mm width and 15mm deep at a distance of 60mm to 75mm including supply of 3 nos of I.O. butt hinges (IS 1341 - 1992) of size 120mm long, 1 no of I.O aldrop of size 300mm × 12mm and 2 nos of I.O. tower bolt of size 200mm × 12mm including proper welding with MS angle frame and shutter alround in proper alignment, inclludiing welding the hinges to the door frames and door shutters and fitings such as aldrop, tower bolt etc., to be welded with door shutter with required base plates of width 110mm to 120mm and height 150mm to 160mm using same GI sheet, placing in shutter wherever required with propere welding etc., including one coat of primer with red oxide of good quality etc., complete in all respects as directed by the departmental officers.

Supplying and fixing of factory made PVC rigid panel door with frame made from MS tubes of 19 gauge size of 19mm x 19mm and covered with heat moulded PVC channel of 5mm thick and width of 50mm to form styles and rails. The inner panel should be inserted between the frame with 6mm thick PVC rigid foam sheet welded/sealed to the styles and rails along with 5mmx25mm PVC beading on all and either sides. The vertical tube may be filled with suitable materials to further enhance the screw holding capacity etc., complete in all respects as directed by the departmental officers.

Solid panel PVC door with frame

Supplying and fixing of PVC sliding door with roller

Supplying and Erecting Pull and Push Type Rolling Shutter with ISI make of approved size and section using 18 GI sheet. The shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers, transportation charges etc complete as directed by the departmental officers.

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames complete in all respect as directed by the departmental officer. The window should be got approved from the Executive Engineer before use on work

Supplying and fixing the UPVC (Un-Plasticized polyvinyl chloride) louvered ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free,the profile are multi chambered sections with wall sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the walll with 100% packing with screws and silicon packing alround the frames etc., complete in all respects as directed by the departmental officers (All floors). The ventilator should be got approved from the departmental officer before use on work, etc.,

Fabrication and supply of GI sheet window of overall size of 1220 mm x 1220 mm using 24 Gauge ( 0.63 mm thick ) G.I.sheet ( I S 277 -1992 ) with MS angle of size 35mmx 35mm x 5mm ( I S 808 - 1989 ) for outer frame alround and "T" section ( I S 1173 - 1978 ) of size 25mm x 25mm x 3mm for central vertical post 2 nos, 4 nos of hold fasts of size 35mm x 35mm x 5mm , 150 mm long, suitably welded with outer frame and split at the ends, including providing 10mm MS Square rods ( I S 1732 - 1989 ), totally 11 nos placing at 100 mm centers, GI sheet window with 3 shutters, every shutter covered with alround frame using MS angle ( I S 808 - 1989 ) of size 25mm x 25mm x 3mm, shutters with vertical grooves (dumpling - machine pressed ) of 25mm width and 15 mm deep at a distance of 60 mm to 75mm , suitably welded to the MS angle frame and GI sheet shutter including fixing 6 Nos of I.O.Butt Hinges ( I S 1341 -1992 )of size 100mm, 3 nos of C.P. hook and eye, 150mm long, 3 nos of handle resting on the MS plate 75 mm x 40 mm x 2 mm thick suitably welded to the shutter/frame wherever required, grinding for smooth finish including one coat of primer with red oxide of good quality etc., complete in all respects as directed by the departmental officers.

Supplying and fixing in position M.S grills of approved design for open to courtyard grill, window and ventilators openings and gate etc., using necessary mild steel flats for inner and outer members which should be fixed on edges including priming coat of best approved quality red oxide primeretc., complete complying with standared specification.

Supplying and fixing in position White / Colour Glazed Model Floor Mounted European Water Closet of best quality and approved make with 100mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using indian adopter joint including all internal fittings, such as, 15mm bras connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition, etc., complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Executive Engineer before use on works) All Floors

Supplying and fixing Oriya type Parryware / Hindware / Equivalant " Indian " Water Closet of size 58cm x 44 cm with 'P' or 'S' trap (white glazed earthern ware of best approved) including concrete packing filling the portion with m-sand, flooring the same area with 7.5cm thick brick jelly lime concrete 32:12-1/2 ( Thirty two of broken brick jelly and twelve and half of lime) using 20mm size brick jelly and finishing the surface with Ceramic tile flooring of size 305mmx305mmx6mm with anti-syphonage connection etc., complete in all respects ( IN GROUND FLOOR)

Supplying and fixing Oriya type Parryware / Hindware / Equivalant " Indian " Water Closet of size 58cm x 44 cm (white colour) with 'P' or 'S' trap (white glazed) earthern ware of best approved quality in all floors other than Ground Floor including concrete packing, filling the sunken portion with brick jelly lime concrete 32:12½ (Thirty two of broken brick jelly and twelve and half of lime) (no sand) using 20mm size broken brick jelly including plastering the sides of the sunken portion in cement mortar 1:3 (one of cement and three of sand) 12mm thick mixed with water proofing compound at 4lbs/cft of cement, applying one coat of britex solution including curing for the sides and bottom of the sunken portion, curing etc. complete in all repects as directed by the departmental officers. (In all floors other than Ground Floor)

Supply and fixing Stainless Steel sink of size 600mmx450mmx200mm confirming to IS 13983:1994 with 32mm dia B class GI waste water pipe and 32mm dia coupling including necessary water supply and drainage arrangements etc., complete in all respect as directed by the departmental officer.

Supplying and fixing in position best quality approved make white gazed earthenware Wash Hand Basin of size 550mm x 400mm with all accessories such as Cast Iron Brackets, 32mm dia CP Waste Coupling, Rubber Plug and Chain, 32mm dia 'B' Class GI Waste Pipe, 15mm dia GM Wheel Valve, 15mm dia Nylon Connection, 15mm dia Brass Nipples, 15mm CP Pillar Tap etc complete in all respect as directed by the departmental officer.

Supplying and fixing in position indian make white glazed earthen ware lipped mouth Porceline flat back urinal of best approved quality with GI pipe connection of suitable length 32mm bell mouthed PVC connestion, 15mm dia GM wheel valve, 15mm dia B Class GI waste water pipe, 15mm Nylon connection, 15mm dia brass nipple etc., fixing the urinal to the wall in position with necessary TW plugs, clamps, shellac etc., including dismantling masonry if necessary and redoing the same to original condition and checked without any leakage complete complying with standard specification. (The urinal should be got approved by the Executive Engineer before use on work) complete in all respect as directed by the departmental officer.

Supplying and fixing of 100 x 75 mm PVC Nahni Trap with grating 4 way/2way (superior quality) having minimum seal of 50 mm conforming to relevant IS specifications with its latest amendments including resting at the bed of brick jelly concrete 1:5:12½ using 40 mm size broken brick jelly etc.,complete in all respects as directed by the departmental officers

White washing two coats using clean shell lime, cost of lime including gum brushes and scaffolding etc., complete as directed by the departmental officers.

Supplying and painting the walls with two coats of wall putty over new plastered surface including preparation of surface, curing ,cost of wall putty and putty plates, brushes,scaffolding and labour charges etc., complete in all floors complying with standard specification.

Painting the walls with two coats of plastic emulsion paint of approved quality over one coat of primer including cost of all materials, putty wherever required, brushes and other alied T &P required for the work and using of existing scaffolding etc., complete as directed by the departmental officers.

Painting newly plastered wall surface with two coats of ready mixed exterior emulsion paint of approved quality have GLIMPSE of SPRING shade over a coat of priming of approved emulsion primer such as Asian (or) its equivalent brand including cost of paint, primer, brushes etc., complete complying with standard specification.

Painting the new wood works two coat with ready mixed synthetic enamel paint (I st class) of approved quality and colour over coat of priming with approved primer including cost of paint brushes ans scaffolding etc., complete in all respects as directed by the departmental officers.

Painting the new iron work with one coat of first class synthetic enamel paint of approved quality and colour in addition over the existing primer coat including the cost of paint patty brushes and scaffolding etc. complete in all respects as directed by the departmental officers

Painting the kerb stone with two coats of ready mixed synthetic enamel paint (I st class) of approved quality and colour including cost of paint brushes and scaffolding etc., complete complying with standard specification as directed by the departmental officer.

Painting the walls with two coats of approved cement paint over one coat of cement primer including cost of cement paint, primer, brushes,scaffolding and labour charges etc., complete complying with standard specification.

Supplying and fixing of following dia uPVC SWR pipe of 6 kg/cm2 of approved quality confirming to IS 13592/1992 (type B) of finolex (or) equivalent with ISI monogram packing the joints including fixing into walls with necessary connection to the sanitary fittings, testing etc. complete in all respects in all floors as directed by the departmental officers.

110mm dia pipes 6kg /cm² uPVC SWR

75mm dia pipes 6kg /cm² uPVC SWR

Supplying, laying the following uPVC SWR pipes with IS 13592/1992 (type B) monogram including jointing with solvent properly to gradient necessary connection to the sanitary fittings in water closet room and bath room including testing etc., complete in all respects as directed by the departmental officers.

110mm dia pipes 6kg /cm² uPVC SWR

75mm dia pipes 6kg /cm² uPVC SWR

Supplying and fixing of 110mm dia uPVC Rain water downfall pipe of 4 kg/cm² conforming to IS 13592-1992 (Type-A) with necessary bends, shoes, cost of special clamps, coupler if necessary including cost of solvent cement, proper aligning, teakwood plugs of approved quality etc., complete in all respects as directed by the departmental officers.

Supplying and fixing the following uPVC SWR fittings confirming to IS14735/1999 complete in all respects as directed by the departmental officers.

110mm dia cowl

75mm dia cowl

110mm dia single Y with door

75mm dia single Y with door

110mm dia PVC Shoe

75mm dia PVC Shoe

110mm dia Door Elbow

75mm dia door Elbow

110mm dia bend

75mm dia bend

Construction of inspection chamber of size 60cm × 60cm for 0.6m depth with Reinforced cement concrete wall of 15cm thick and base slab of 10cm thick of 1:2:4 proportion (One of cement, two of M-sand and four of hard broken granite stones) using 20mm gauge hard broken granite stones including the cost of steel and fabrication of reinforcement grills in position shutterring centering etc.,cement concrete 1:4:8 20mm HBSJ of 10cm thick for foundation including channeling benching etc., and top covered with extra heavy duty cover slab SFRC slab with frame 600mm(clear opening) including casting and fixing in position and necessary earth work excavation, refilling the sides of foundation in all soils except hard rock requiring blasting etc., complete in all respects in all floors as directed by the departmental officers. 60 CM depth

Supplying and fixing of SFRC Manhole cover with frame of size 0.60 x 0.60 m ( heavy type ) etc., complete in all respects as directed by the departmental officer

Supplying and fixing of CI steps of 14 " size etc., complete in all respects as directed by the departmental officer

Supplying, laying and jointing UPVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to IS 4985/2000 of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works. complete in all respects as directed by the departmental officers.

20 mm dia UPVC pipe for delivery

25 mm dia UPVC pipe for delivery

32 mm dia UPVC pipe for delivery

40 mm dia UPVC pipe for inlet

50mm UPVC Pipe ( 10Kg / cm²)

Supplying of uPVC pipe specials of approved quality suitable to uPVC pipe as per IS4985:1999 at site of work etc., complete in all respects as directed by the departmental officers.,

50mm dia Coupler

50mm dia UPVC bend

50mm dia UPVC union

50mm dia UPVC Tee

50mm dia UPVC Hex nipple

40mm dia Elbow

40mm dia Coupler

40mm dia MTA

40mm dia bend

40mm dia Tee

32mm dia elbow

32 mm dia TEE

32 mm dia Nipple

32mm x 25 mm reducer

25mm coupler

25mm Elbow

25mm dia Tee

25mm dia FTA

25mm dia UPVC Nipple with check nut and washer

25mmx 20mm reducer

20mm coupler

20mm elbow

20mm dia TEE

20mm dia FTA

20mx 15 mm Threaded (Female) reducer

20mm dia PVC screw down Tap (heavy type)

15mm dia PVC screw down Tap (heavy type)

Supply of GI pipes and ISS 1239 (medium) screwed at both ends and socketed both ends and etc., complete in all respects as directed by the departmental officers. 40 mm dia GI pipe @ inlet

Labour charges for cutting and jointing the G.I. rigid pipes using solvent cement required with necessary specials of the following dia above ground level including fixing to wall with necessary teak wood plugs, clamps and screws making holes in the wall etc., complete in all respects as directed by the departmental officers. 40 mm dia GI pipe @ inlet

Supply and fixing of 50mm dia GI pipe of approved brand having ISI mark etc., complete in all respects as directed by the departmental officers.

Supplying and fixing of GI and GM specials confirming to ISI etc., complete as directed by the departmental officers

50mm dia GM gate valve

50mm x 40mm dia GI Reducer

40mm GI Coupler

40mm dia GI Elbow

40mm GI Bend

40mm dia GI union

40 mm dia GM Gate valve

32mm GM wheel valve

25mm GM wheel valve

Finishing the top of roof with reflected ceramic cooling tiles of size 305mmx305mmx7mm of approved brand and quality in cement mortar 1:3(one of cement and three of M-sand) 12mm thick mixed with water proofing compound 2% by weight of cement used and pointing with same mortar etc., complete in all respects as directed by the departmental officers.

Supply and run off 2 of 2.50 sq.mm PVC insulated single core unsheathed copper conductor cable of 1100V grade with ISI mark confirming to IS:694/1990 with continuous earth connection by means of 1.50 sqmm PVC insulated single core unsheathed copper conductor cable confirming to IS:694/1990 in suitable PVC rigid pipe 1.8mm thick concealed on walls and ceiling for mains including the cost of cable, PVC pipes and specials, cement, brass screws, TW plugs, saddles and labour etc., complete in all respects as directed by the departmental officers.

Wiring with 2 of 1.5 sq.mm PVC insulated single core unsheathed copper conductor cable of 1100 V grade with ISI mark with continuous earth connection by means of 1.5 sq.mm PVC insulated single core unsheathed copper conductor cable of 1100 V grade with ISI mark in suitable PVC rigid pipe 2mm thick with ISI mark on surface run with suitable size concealed 16 gauge M.S. switch box covered by laminated hylem sheet 3 mm thick for LIGHT POINTS including the cost of cable, PVC pipes and specials, brass screws, ceiling rose, flush type 5 Amps SP Mark switch, PVC junction box, 16 gauge M.S.switch box covered by laminated hylem sheet 3mm thick T.W.plugs, cement and labour, circuit mains etc., complete. box, covered by laminated hylem sheet 3mm thick T.W.plugs, cement and labour, circuit mains etc., complete. in all respects as directed by the departmental officers

With Ceiling Rose

With Bakelite Battern Holder

Wiring with 2 of 1.5 sq.mm PVC insulated single core unsheathed copper conductor cable of 1100 V grade with ISI mark with continuous earth connection by means of 1.5 sq.mm PVC insulated single core unsheathed copper conductor cable of 1100 V grade with ISI mark in suitable PVC rigid pipe 2mm thick with ISI mark on surface run with suitable size concealed 16 gauge M.S. switch box covered by laminated hylem sheet 3 mm thick for FAN POINTS including the cost of cable, PVC pipes and specials, brass screws, ceiling rose, flush type 5 Amps SP Mark switch, PVC junction box, 16 gauge M.S.switch box covered by laminated hylem sheet 3mm thick T.W.plugs, cement and labour, circuit mains etc., complete. box, covered by laminated hylem sheet 3mm thick T.W.plugs, cement and labour, circuit mains etc., complete. in all respects as directed by the departmental officers

Supplying and fixing of 5 A 3 pin and 2 pin combined flush type wall socket with 5 A flush type switch concealed in suitable MS box in flush with wall and covered with 3mm thick hylem sheet including cost of wall socket, switch and labour charges for wall cutting, grouting, flushing and making good, painting with primary and finishing coat for MS box etc., complete as directed bu the departmental officers.

Wiring with 2x1.5sqmm PVC insulated SC unsheatedCU conductor of 1100 V grade with ISI mark confirmingto IS: 694/1990 in suitable PVC rigid pipe of 1.8mmthick with ISI mark concealed in wall and ceiling withPVC accessories in flush with wall for 5 AMPS 3 PINC.S. PLUG POINT AT CONVENIENT PLACES including the cost of cable, PVC pipes and specials,brass screws, flush type 5 amps 3 Pin C.S. plug, 16gauge Msjoint box, 16 gauge MS switch box coveredby laminated hylem sheet 3mm thick, cement, labourand making good of the concealed portion with suitablecolour for concealed PVC plug point. complete in all respects as directed by the departmental officers.

Supplying and fixing of 15A 3 pin flush type wall socket with15A flush type switch concealed in suitable MS box in flush with wall andcovered with 3mm thick hylem sheet including cost ofwall socket, switch and labour charges fo wall cutting,grouting, flushing and making good, painting withprimary and finishing coat for MS box etc., complete asdirected by the departmental officers.

Supplying and fixing of 4 way (6 Module) with 4 No's of MCB & 32 A DP Isolator includind labour charges etc., complete in all resspcets as directed by the departemental officers

Supply and run off 2 of 2.50sqmm PVC insulated single core unsheathed copper conductor cable of 1100 V grade with ISI mark confirming to IS:694/1990 with continious earth connection by means of 1.50 sqmm PVC insulated single core unsheathed copper conductor cable confirming to IS:694/1990 in suitable PVC rigid pipe 1.8mm thick concealed in wall for mains including the cost of PVC pipes and specials, cables, cement, brass screws, T.W plugs, saddles and labour etc.for concealed staircase light point., complete in all respects as directed by the departmental officers.

Supply and fixing water tight Bulk Head fitting (heavy type) with guard suitable for 100/60W bulb including the cost of bulb, necessary connection cost of materials etc.,complete. in all respects as directed by the departmental officers

Supply and installation maintenance free GI Earthing System comprising of 50mm dia and 2 mtr. long earth electrode of low carbon steel rod with 100 micron bonding and 25 kgs. of carbon based environment friendly backfill compound and suitable clamp complete. in all respects as directed by the departmental officers

Supplying and run of 8 SWG copper wire on walls/below ground level necessary'U' nails/ earth work excavation andrefilling etc. including the cost of allmaterials etc., all complete in all respects as directed by the departmental officers.

Supplying and laying of 3 -1/2 x 70 sq. mm pvc armoured Aluminium LT UG cable of approved brand having ISI mark in a trench to be excavated to a depth of 0.75 meter, putting 0.15 m layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good etc., complete in all respects

Supplying and laying of 3-1/2 x 70 sq. mm pvc armoured Aluminium LT UG cable of approved brand having ISI mark on post or wall with M.S clamps etc., complete in all respects

Supplying and fixing brass cable gland for 3 1/2 x 70 sq. mm PVC armoured LT UG cable with earth connection etc., complete in all respects.

Supplying and fixing cable end termination for 3 ½ x 70 sq.mm PVC armoured LT UG cable with earth connection etc., complete in all respects.

Supplying and fixing of 3 Nos., of 100 A porcelain fuse units 500 volt of approved brand having ISI mark in T.W. Board of suitable size etc., complete in all respects.

Supply & run of 2 x 4 Sq.mm of PVC insulated unsheethed single core FR copper cable of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continous earth connection by 1 run of 1.5 Sq.mm PVC insulated unsheathed copper cable of 1100 V grade making good of the concealed portion etc., complete in all respects.

Supply and erection of 125 Amps capacity floor mounting type metering panel board (Cubical type) with bus bar chamber made up of CRCA sheet for 3 phase 4 wire system with 40mm x 10mm tin coated copper flats for phases and neutral; cable chamber, switch chamber and with 2 Nos. 25mm x 3 mm tinned copper flat for the earth bus on the rear side of the panel board; necessary interconnections by copper flat of suitable sizes; suitable PVC colour sleeves for the interconnecting copper flats / rigid copper wire; earth connections to all switches / bus bar by copper flats of suitable sizes from the earth bus; hylum sheet separation between bus bar and switches; 3 nos of LED pilot lamps with switches, fuse units, suitable angle iron frame size of 37.5 mm x 37.5 mm x 6 mm with powder coated painting over one coat of red oxide and with numbering; superscription of cables sizes, capacity of switches etc and incorporating the following:Outgoings: 1. Singe phase services 33 Nos. 32A DP MCB / 40A 10 KA DP MCB and 33 Nos. 32A, 1 Nos. 63A 4P MCB and 3 Nos. 63A, fuse units 25mm x 3mm x 15mm copper flats for neutral and earth Space provision for TNEB energy meter with glass cover.Bus capacity: A3 phase 4 wire copper 2 Nos. Dummy provision Internal connections by 2 runs of 4 sq.mm PVC insulator unsheathed copper contactor of 1100 V grade from TNEB cutout to the meter and from the meter to the 32A DP MC switch / 32 A 10 KA DP MCB 3 Nos of LED pilot lamps with fuse units, switches / and interconnections; inter connection to the bus bar by 25mm x 3mm T C copper flats for phases and neutral from 125A TPN SDF to the bus; interconnection by No. 8 SWG copper for the phases and neutral from the 32A 10 KA DP MCB switch to the bus; 6mm thick hylum sheet separation between bus bar chamber and switches chamber; insulators for the support for the bus; superscripting on the panel board the size, capacity of cable, switches, location etc. 2 nos. metallic danger boards.

Supply and erection of 125 Amps capacity floor mounting type metering panel board (Cubical type) with bus bar chamber made up of CRCA sheet for 3 phase 4 wire system with 40mm x 10mm tin coated copper flats for phases and neutral; cable chamber, switch chamber and with 2 Nos. 25mm x 3 mm tinned copper flat for the earth bus on the rear side of the panel board; necessary interconnections by copper flat of suitable sizes; suitable PVC colour sleeves for the interconnecting copper flats / rigid copper wire; earth connections to all switches / bus bar by copper flats of suitable sizes from the earth bus; hylum sheet separation between bus bar and switches; 3 nos of LED pilot lamps with switches, fuse units, suitable angle iron frame size of 37.5 mm x 37.5 mm x 6 mm with powder coated painting over one coat of red oxide and with numbering; superscription of cables sizes, capacity of switches etc and incorporating the following:Outgoings: 1. Singe phase services 35 Nos. 32A DP MCB / 40A 10 KA DP MCB and 35 Nos. 32A, 1 Nos. 63A 4P MCB and 3 Nos. 63A, fuse units 25mm x 3mm x 15mm copper flats for neutral and earth Space provision for TNEB energy meter with glass cover.Bus capacity: A3 phase 4 wire copper 2 Nos. Dummy provision Internal connections by 2 runs of 4 sq.mm PVC insulator unsheathed copper contactor of 1100 V grade from TNEB cutout to the meter and from the meter to the 32A DP MC switch / 32 A 10 KA DP MCB 3 Nos of LED pilot lamps with fuse units, switches / and interconnections; inter connection to the bus bar by 25mm x 3mm T C copper flats for phases and neutral from 125A TPN SDF to the bus; interconnection by No. 8 SWG copper for the phases and neutral from the 32A 10 KA DP MCB switch to the bus; 6mm thick hylum sheet separation between bus bar chamber and switches chamber; insulators for the support for the bus; superscripting on the panel board the size, capacity of cable, switches, location etc. 2 nos. metallic danger boards.

Supply and erection of 125 Amps capacity floor mounting type metering panel board (Cubical type) with bus bar chamber made up of CRCA sheet for 3 phase 4 wire system with 40mm x 10mm tin coated copper flats for phases and neutral; cable chamber, switch chamber and with 2 Nos. 25mm x 3 mm tinned copper flat for the earth bus on the rear side of the panel board; necessary interconnections by copper flat of suitable sizes; suitable PVC colour sleeves for the interconnecting copper flats / rigid copper wire; earth connections to all switches / bus bar by copper flats of suitable sizes from the earth bus; hylum sheet separation between bus bar and switches; 3 nos of LED pilot lamps with switches, fuse units, suitable angle iron frame size of 37.5 mm x 37.5 mm x 6 mm with powder coated painting over one coat of red oxide and with numbering; superscription of cables sizes, capacity of switches etc and incorporating the following:Outgoings: 1. Singe phase services 49 Nos. 32A DP MCB / 40A 10 KA DP MCB and 48 Nos. 32A, 1 Nos. 63A 4P MCB and 3 Nos. 63A, fuse units 25mm x 3mm x 15mm copper flats for neutral and earth Space provision for TNEB energy meter with glass cover.Bus capacity: A3 phase 4 wire copper 2 Nos. Dummy provision Internal connections by 2 runs of 4 sq.mm PVC insulator unsheathed copper contactor of 1100 V grade from TNEB cutout to the meter and from the meter to the 32A DP MC switch / 32 A 10 KA DP MCB 3 Nos of LED pilot lamps with fuse units, switches / and interconnections; inter connection to the bus bar by 25mm x 3mm T C copper flats for phases and neutral from 125A TPN SDF to the bus; interconnection by No. 8 SWG copper for the phases and neutral from the 32A 10 KA DP MCB switch to the bus; 6mm thick hylum sheet separation between bus bar chamber and switches chamber; insulators for the support for the bus; superscripting on the panel board the size, capacity of cable, switches, location etc. 2 nos. metallic danger boards.

Supply and erection of 125 Amps capacity floor mounting type metering panel board (Cubical type) with bus bar chamber made up of CRCA sheet for 3 phase 4 wire system with 40mm x 10mm tin coated copper flats for phases and neutral; cable chamber, switch chamber and with 2 Nos. 25mm x 3 mm tinned copper flat for the earth bus on the rear side of the panel board; necessary interconnections by copper flat of suitable sizes; suitable PVC colour sleeves for the interconnecting copper flats / rigid copper wire; earth connections to all switches / bus bar by copper flats of suitable sizes from the earth bus; hylum sheet separation between bus bar and switches; 3 nos of LED pilot lamps with switches, fuse units, suitable angle iron frame size of 37.5 mm x 37.5 mm x 6 mm with powder coated painting over one coat of red oxide and with numbering; superscription of cables sizes, capacity of switches etc and incorporating the following:Outgoings: 1. Singe phase services 39 Nos. 32A DP MCB / 40A 10 KA DP MCB and 48 Nos. 32A, 1 Nos. 63A 4P MCB and 3 Nos. 63A, fuse units 25mm x 3mm x 15mm copper flats for neutral and earth Space provision for TNEB energy meter with glass cover.Bus capacity: A3 phase 4 wire copper 2 Nos. Dummy provision Internal connections by 2 runs of 4 sq.mm PVC insulator unsheathed copper contactor of 1100 V grade from TNEB cutout to the meter and from the meter to the 32A DP MC switch / 32 A 10 KA DP MCB 3 Nos of LED pilot lamps with fuse units, switches / and interconnections; inter connection to the bus bar by 25mm x 3mm T C copper flats for phases and neutral from 125A TPN SDF to the bus; interconnection by No. 8 SWG copper for the phases and neutral from the 32A 10 KA DP MCB switch to the bus; 6mm thick hylum sheet separation between bus bar chamber and switches chamber; insulators for the support for the bus; superscripting on the panel board the size, capacity of cable, switches, location etc. 2 nos. metallic danger boards.

Supply and erection of 125 Amps capacity floor mounting type metering panel board (Cubical type) with bus bar chamber made up of CRCA sheet for 3 phase 4 wire system with 40mm x 10mm tin coated copper flats for phases and neutral; cable chamber, switch chamber and with 2 Nos. 25mm x 3 mm tinned copper flat for the earth bus on the rear side of the panel board; necessary interconnections by copper flat of suitable sizes; suitable PVC colour sleeves for the interconnecting copper flats / rigid copper wire; earth connections to all switches / bus bar by copper flats of suitable sizes from the earth bus; hylum sheet separation between bus bar and switches; 3 nos of LED pilot lamps with switches, fuse units, suitable angle iron frame size of 37.5 mm x 37.5 mm x 6 mm with powder coated painting over one coat of red oxide and with numbering; superscription of cables sizes, capacity of switches etc and incorporating the following:Outgoings: 1. Singe phase services 29 Nos. 32A DP MCB / 40A 10 KA DP MCB and 33 Nos. 32A, 1 Nos. 63A 4P MCB and 3 Nos. 63A, fuse units 25mm x 3mm x 15mm copper flats for neutral and earth Space provision for TNEB energy meter with glass cover.Bus capacity: A3 phase 4 wire copper 2 Nos. Dummy provision Internal connections by 2 runs of 4 sq.mm PVC insulator unsheathed copper contactor of 1100 V grade from TNEB cutout to the meter and from the meter to the 32A DP MC switch / 32 A 10 KA DP MCB 3 Nos of LED pilot lamps with fuse units, switches / and interconnections; inter connection to the bus bar by 25mm x 3mm T C copper flats for phases and neutral from 125A TPN SDF to the bus; interconnection by No. 8 SWG copper for the phases and neutral from the 32A 10 KA DP MCB switch to the bus; 6mm thick hylum sheet separation between bus bar chamber and switches chamber; insulators for the support for the bus; superscripting on the panel board the size, capacity of cable, switches, location etc. 2 nos. metallic danger boards.

Supply and erection of 125 Amps capacity floor mounting type metering panel board (Cubical type) with bus bar chamber made up of CRCA sheet for 3 phase 4 wire system with 40mm x 10mm tin coated copper flats for phases and neutral; cable chamber, switch chamber and with 2 Nos. 25mm x 3 mm tinned copper flat for the earth bus on the rear side of the panel board; necessary interconnections by copper flat of suitable sizes; suitable PVC colour sleeves for the interconnecting copper flats / rigid copper wire; earth connections to all switches / bus bar by copper flats of suitable sizes from the earth bus; hylum sheet separation between bus bar and switches; 3 nos of LED pilot lamps with switches, fuse units, suitable angle iron frame size of 37.5 mm x 37.5 mm x 6 mm with powder coated painting over one coat of red oxide and with numbering; superscription of cables sizes, capacity of switches etc and incorporating the following:Outgoings: 1. Singe phase services 41 Nos. 32A DP MCB / 40A 10 KA DP MCB and 33 Nos. 32A, 1 Nos. 63A 4P MCB and 3 Nos. 63A, fuse units 25mm x 3mm x 15mm copper flats for neutral and earth Space provision for TNEB energy meter with glass cover.Bus capacity: A3 phase 4 wire copper 2 Nos. Dummy provision Internal connections by 2 runs of 4 sq.mm PVC insulator unsheathed copper contactor of 1100 V grade from TNEB cutout to the meter and from the meter to the 32A DP MC switch / 32 A 10 KA DP MCB 3 Nos of LED pilot lamps with fuse units, switches / and interconnections; inter connection to the bus bar by 25mm x 3mm T C copper flats for phases and neutral from 125A TPN SDF to the bus; interconnection by No. 8 SWG copper for the phases and neutral from the 32A 10 KA DP MCB switch to the bus; 6mm thick hylum sheet separation between bus bar chamber and switches chamber; insulators for the support for the bus; superscripting on the panel board the size, capacity of cable, switches, location etc. 2 nos. metallic danger boards.

Supply and delivery of direct online starter confirming to IS13947,IEC 60947-1 suitable KW rating for operation i AC/three Phase/50HZ(± 5%)and 415 V(±10%) including Ammeter, Voltmeter, Thermal Overload relay, 16amps 2 pole Magnetic Contactor with under Voltage rotection,Indicationlamp, starting capacitor, running capacitor and On/Off Push button switches,5 way connector, wiring with 1 sq. mm/1.5 sq. mm copper PVC insulatedcable, powder coated vermin proof box including the capacitor (the cost ofcapacitor is to be taken separately).testing the pumpset and trail run for 10 days. complete in all respects as directed by the departmental officers

Supplying, fixing, testing and commissioning the 6 Way Vertical TPN Distributions boards; IP43 with double door (Metal); with 12module incomers and 18 Single Phase/Three Phase/ MCB’s outgoing; as per IS 8623 III complete in all respects as directed by the departmental officers

Supplying, fixing, testing and commissioning the MINIATURE CIRCUIT BREAKERS (MCB) 240 V/415 V 50HZ AC Supply Suitable For Both Lighting And Motor Circuits. Single pole 6A to 32A,10 KA (For Lightings) complete in all respects as directed by the departmental officers

Jointing Of L.T Cable-3.0,3.5,4 core 1.1 kV Grade Armoured Marking.aluminium conductor cable confiring To IS 1554 And As amended Thereafter Part I With ISI specification complete in all respects as directed by the departmental officers

Supplying, fixing, testing and commissioning PVC Insulated Single Core Multi Strand Fire retardant Flexible Copper cable with I S Mark Conforming to I S 694/1990. Copper cable Single Core 6.00 SQMM complete in all respects as directed by the departmental officers

Supplying and fixing 600x450mm 19mm teak wood plank with supporting reapers 1" x 1.1/2" both sides with painting including cost on wall with necessary bolts and nuts with the following for availing three phase service connection from TNEB for common areas, lift, pump set etc. Including 1) 100 A fuse units, 2) 1 No. neutral link copper flat of size 25x3x150mm, 3) 1 No. of earth link of copper flat of size 25x3x150mm, and 4) Space provision for 3 phase energy meter complete in all respects as directed by the departmental officers

Supplying and fixing of 100 amps 500volts grade porcelain fuse unit on suitable teak wood plank varnished to be fixed on the top of EB pole with clamps including cost of all materials complete.

Labour charges for cutting threading and jointing the following dia of GI pipes with necessary specials and jointing with white lead and spunyarn, earthwork excavation for laying the pipes wrapping with tarred tape and reffing the trenches whre the pipes are laying underground complete complying with standard specification complete in all respects as directed by the departmental officers 40mm dia GI pipe

Supply and fixing 16amps DPIC switch with metal clad(side handle) of 500 V with F & N on suitable teak wood Board of size 30cmx20cmx6.3cm including necessary internal conection,earth connection etc., complete as directed by the departmental officers.

Supplying and fixing bakelite battern holder straight orangle type and 40 W bulp on suitable T.W.roundblockincluding necessary interal connections, cost of all materials, labour etc., complete as directed by the departmental officers.

Supplying and fixing of 1200 mm (48") AC ceiling fancomplete with stepped electronic 300 W regulator with1 m down rod with fan clamp, side plates and crossarm of size (18") etc., complete as directed by thedepartmental officers.

Supply and fixing of TNEB meter Board suitable for 63 A three phase service connection with 63A fuseunit(500V) 63A neutral link and earth link (1" x 1/8"Copper flat) on teak wood plank of size 600mm x450mm x 19mm with supportingT.W.reepers of 1" thick oneither sider withpainting withsuitable bolt and nuts for fixingthe TWplank on wall withearth connection and interconnection with 7/20 PVCinsulated copper wirefrom EBmeter to fuse unit. complete in all respects as directed by the departmental officers

Providing Vertical Expansion Joint Pad of 40mm thickness (1000 x 2000 mm = 2.0 m2 / No.) of 60cm width in between twinblocks R.C.C columns from top of Pedistal including filling inner space with suitable non - absorbent flexible and well compressible filter materials of approved qanlity and brand polysulphide seal ends with suitable filter materials after finishing the sides or RCC columns etc., complete in all respects as directed by the departmental officers

Providing Horizontal Expansion Joint pad of 40mm thickness (1200mm x 2400mm = 2.8m2/ Noo.) of 45cm width I between twin blocks RCC slab from end to end including filling inner space with suitable non - absorbent flexible and well co,mpressible filter materilas of approved quality and brand polysulphide seal ends with suitable filter materils after finishing the sites or RCC slab, walls etc., complete in all respects as directed by the departmental officers.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304LGradeStainlessSteel pipe of 1.60mmthick at required locations to aheight of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipeof 1.60mmthick in between. The vertical pipe has to be welded to the 100X100X6mm MSbase plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete as directed by the departmental officers.

Supplying and fixing of UPVC -non pressure pipes as per IS 15328/2003[SN8-SDR(S 16.5)] and laying and jointing of UPVC pipes to the proper grade and alignment as indicated in drawing / design and hydraulically testing of the pipe line. The rate shall include cost of all necessary jointing materials testing charges with water conveyed within a lead of 1km, labour etc. complete etc complete in all respect as directed by the departmental officers.

160mm dia pipe

200mm dia Pipe

Supplying and fixing of PVC pipe specials of approved quality suitable to PVC pipe as per IS 10124/1982- Part-II at site of work etc., complete in all respects as directed by the departmental officers.

160 mm dia PVC bend

160 mm dia PVC Tee

160mm dia PVC coupler

Supplying and Fixing of 300mm dia RCC Hume pipes NP 2 Class with necessary gradient including labour for fixing, jointing and cost of pipe etc all complete as directed by the departmental officers.

Construction of circular RCC manhole of 1.20m internal dia for following depth with Reinforced cement concrete wall of 15cm thick and base slab of 15cm thick of 1:2:4 proportion (One of cement Two of M-Sand and Four of hard broken granite stone) using 20mm gauge hard broken granite stones including the cost of steel and fabrication of reinforcement grills in position shutterring centering etc., over a bed of cement concrete 1:4:8 20mm HBSJ of 10cm thick for foundation including channeling benching etc., and top covered with heavy duty cover slab SFRC slab with frame 600mm(clear opening) including casting and fixing in position and necessary earth work excavation, refilling the sides of foundation in all soils except hard rock requiring blasting etc., complete in all respects in all floors as directed by the departmental officers.

1.20m depth

1.50m depth

2.00m depth

Providing rain water harvesting using 3 nos.of RCC well rings of 90cm inner dia (clear) with 5cm wall thickness made out of cement concrete 1:2:4 using 20mm hard broken jelly to a height of 30cm each supplying and fabricating 16 nos. of 6mm dia MS rod vertically and 3 nos. of 6mm dia MS rod circumferentially tied together with 18 guage binding wire for well rings including necessary earth work excavation 1m dia to a depth of 1m, supplying and filling 40mm HBG inside the erected well ring to a depth of 90cm, and top covered with RCC circular perforated cover slab of 1m dia and 5cm thick which inclusive of cost and fabrication of 6mm M.S reinforcement at 15 cm spacings on both directions and one 6mm M.S rod ties at the edge of the slab circumferentially including cost of moulding, curing, finishing and well placing in position and disposing off excavated earth with all initial leads and lifts in places as shown by the Departmental officers etc., complete in all respects.

Construction of Gully chamber of size 0.23m x 0.23m x 0.3m depth with brick jelly concrete 1:5:121/2 using 40mm size brick jelly 15cm thick for foundation 23cm brickwork masonry wall in CM 1:5(one of cement, five of sand) using stock bricks plastered with CM 1:3 12mm thick, including channelling benching top covered with precast RCC cover slab with 4cm thick excluding cost and fabrication of reinforcement of grills but including earthwork excavation and refilling the sides of foundations in all soils except hard rock refilling plastering complete in all respects.

Supplying and fixing in position of HDPE cylidrical vertical tank with closed tap one moulded like 1000 liters capacity with suitable locks drilled for inlet and outlet,the tank shall be fixed as per the direction of the the departmental officers. Make: SINTEX / EQUIVALENT

Supplying and laying the Rubber Moulded Hydraulic Pressed machine made inter locking concrete paver block madeout of M20 grade concrete of approved design in colour over the bed of M-Sand filling including cost of materials,labour for laying etc., complete as directed by the departmental officers. For 63mm thick Paver Block.

Supplying and fixing the RCC kerb wall of size 45cm x 15cm x 45cm tk. in CC 1:2:4 ( one of cement, two of sand and four of hard brocken stone jelly) including cost of moulding and curing etc. and fixing in position complete in all respects.

Supply and delivery of Open well Submersible pump set conforming to IS 14220 /2002 and as amended thereafter and BEE 3 Star Rated capable of discharging the following duties due to all causes. The pump shall be withbstainless steel shaft and dynamically balanced bronze mixed type impeller, CI FG 200 grade casing and brass screws and rotor shall be of copper rod as per IS 613/1984 with ISI mark. The pump suitable for installation in sump with 1.1KV grade 3 core suitable copper flat submersible cable to a length of 15m with necessary cable joints. The non-return valve located at the top of the pump in the discharge outlet connection is to be designed with minimum friction. The pump should be directly coupled to 2880 RPM, three phase, 50Hz (±5), 415V+6% & 415V-15% squirrel cage induction motor suitable for DOL upto 5 HP , Fully Automatic Air break Star Delta up to 20 HP and Auto Transformer starter for above 20 HP starting and for continuous operation. complete in all respects as directed by the departmental officers

Labour charges for the erection of submersible pumpsets in borewell/open well including fixing and jointing submersible cable with proper clamps upto the starter to required depth and also fixing the riser pipes to the required depth valves erection clamps, pressure gauges upto the exterior wall of pumproom and erection of panel board consisting of TPICN switches, starter,voltmeter,ammeter,three pilot indicating lamps,capacitor,single phasing preventor,water level guard and laying and jointing cables. 5HP submersible motor. complete in all respects as directed by the departmental officers

Supplying and fixing the following COARSE SCREEN including cost of materials, labour charges for fixing, transportation etc., complete in all respect, SS BUCKET SCREEN of suitable to inlet sewer line Size with spacing 12 mm.(Coarse) Type : Bar screen Size: 600mm X 1500mm MOC: SS 304 Make: Green Terra/Ion Exchange

Supplying and fixing the following FINE SCREEN including cost of materials, labour charges for fixing, transportation etc., complete in all respect, (MANUAL) SS FINE SCREEN of suitable to inlet sewer line Size with spacing 6 mm.(FINE) Type : Bucket screenSize: 600mm X 1500mm MOC: SS 304 Make: Green Terra/Ion Exchange

Supplying and fixing the following including cost of materials, labour charges for fixing, transportation etc., complete in all respect RAW SEWAGE TRANSFER PUMPS: Sewage feed pump to transfer sewage from sump to SBR tank of type Vertical, submersible pump set (1 working + 1 standby) capable of handling 50 mm solids with the following specifications, capacity of 67cum/hour at Head 10 m of Kirloskar / Equivalent make with cast Iron casing and SS impeller and as per IS Specification including necessary valves and fittings &suitable level sensor arrangements to transfer the sewage to pre-treatment. Type : vertical, submersible Material of Construction : CI Capacity : 67.0 m3/hour @ 10m head Accessories : Lifting Rope, Dry Run Protection Make : Kirloskar /Crompton/Equivalent

AIR BLOWER Supply , Installation , Testing and Commissioning of Air Blowers in 2 nos of SBR tank to supply air to SBR tank of type Twin lobe (1 working +1 Standby) with the following specifications , capacity of 500 Cu.m/hr, total pressure of 0.5 kg/sq.cm with suitable motor and all accessories. Air Blower Make : A1 / Airvac /KAY/ Equivalent Motor Make : Kirloskar / Crompton/Equivalent

AIRLINE ARRANGEMENTS FOR SBR TANK Supply , Installation , Testing and Commissioning Air grid arrangements to Collection tank & SBR Tank to deliver 500 Cum/hr air with following specifications , MOC UPVC and MS , total pressure 0.6 Kg/Sq.cm with standardspecification & accessories Make : Supreme /Finolex/Equivalent

DIFFUSERS FOR AERATION Supply , Installation , Testing and Commissioning Diffusers for aeration tank to distribute 500 cum/hr of air to the SBR tank with following specification Type : Tubular Fine pore, Fine Bubble Fixed Type, Diffusers Material: EPDM with accessories Make : Tecpro / SSI Aeration/equivalent

SLUDGE TRANSFER PUMP Supply, Installation, Testing and Commissioning of sludge pump to transfer sludge from SBR tank of type Horizontal, Centrifugal, Non Clog pump set (1 working +1 standby) capable of handling 50 mm solids with the following specifications inclusive of taxes, loading, conveyance to site unloading etc., capacity of 10 cum/hour at Head 12 m of Kirloskar / Equivalent make with cast Iron casing and SSimpeller and as per IS Specification including necessary valves and fittings. Type : Horizontal, Centrifugal, Non Clog Material of Construction : Cast Iron Capacity : 10 m3/hour @ 12 m head Accessories : Base Plates, Canopy Make : Kirloskar /Equivalent 1 Working + 1 Stand By

SLUDGE DISPOSAL PUMP Supply, Installation, Testing and Commissioning of sludge pump to transfer sludge from Aerobic Digestion tank of type Horizontal, Centrifugal, Non Clog pump set (1 working +1 standby) capable of handling 50 mm solids with the following specifications inclusive of taxes, loading, conveyance to site unloading etc., capacity of 10 cum/hour at Head 12 m of Kirloskar / Equivalent make with cast Iron casing and SS impeller and as per IS Specification including necessaryvalves and fittings. Type : Horizontal, Centrifugal, Non Clog Material of Construction : Cast Iron Capacity : 10 m3/hour @ 12 m head Accessories : Base Plates, Canopy Make : Kirloskar /Equivalent 1 Working + 1 Stand By

Decantation Valve for SBR tank Supply , Installation , Testing and Commissioning Motor operated Butterfly valve wit Automatic PLC Control to decant the clear water from SBR I & SBR II to Decant water Tank MOC : SS 304

FILTER FEED PUMP Supply , Installation , Testing and Commissioning Filter feed pumps to transfer clarified water from SBR tanks to filters with following specifications, Mono block Centrifugal pump of capacity 20.0 cum/hr with 30 m headPUMP -Kirloskar / Equivalent1Working + 1Stand By

PRESSURE SAND FILTER Supply , Installation , Testing and Commissioning Pressure Sand filter of capacity 20 cum/hr to filter the suspended solids in the sewage with following specifications, Vertical, Cylindrical with design pressure 5.0 kg/cm2 with working pressure 3.0 kg/cm2 with service flow rate 25 Cum /hr , with MOC MSEP with frontal pipe line arrangements and Butterfly Valve, Media - Graded Pebbles,Silex, Graded filtering Sand with accessories. Size: 1.5 m dia x 1.5 m ht – 1nos Shell Thickness: 6mm & Dish Thickness 8mm Make: Green Terra/Ion Exchange

ACTIVATED CARBON FILTER Supply , Installation , Testing and Commissioning Activated carbon filter of capacity 20 cum/hr to remove odour in the sewage with following specifications, Vertical, Cylindrical with design pressure 5.0 kg/cm2 with working pressure 3.0 kg/cm2 with service flow rate 20 Cum /hr , with MOC MSEP with frontal pipe line arrangements and Butterfly Valves, Media - Graded Pebbles, Silex, Graded filtering Sand and Activated carbon withaccessories. Size: 1.5 m dia x 1.5 m ht – 1nos Shell Thickness: 6mm & Dish Thickness 8mm Make: Green Terra/Ion Exchange

UV SYSTEM Supply , Installation , Testing and Commissioning UV disinfection system of capacity 20 cum/hr to disinfect the treated sewage with following specifications ,Size : 600 mm Dia X1500 mm, Inlet & outlet Connection : 3” Flanged End ,Max. Operating pressure: 3 Bar, MOC of housing : SS 304 withnecessary accessories & fittings. Lamp make : HITECH / LIGHT SOURCE / ALPHA / Equal

Supply , Installation , Testing and Commissioning ELECTROMAGNETIC FLOW METER & ULTRASONIC FLOWMETER – FOR INLET & OUTLET Size : 65 NBType : Electro MagneticMake : Aster /GTE/ EQUAL

SUPPLY OF INTER CONNECTING PIPING WORKS Supply of Piping works including Suction and Delivery of Transfer Pumps and Dosing pumps, with necessary supports, excavation, backfilling, alignment, with followingspecificationsPipes & FittingsMaterial : UPVC / MSPressure rating : UPVC - 6 kg/cm2, MS - 15kg/cm2Make : UPVC - SUPREME/ FINOLEX /EQUALMS/GI - Tata, Jindal/ Equivalent ValvesDiaphragm Valves, Gate Valves, Ball Valves, Non Return Valves Butterfly Valves, Needle Valves Material : Polypropylene, CI, Carbon Steel Stainless Steel Standard : BS 5351Working pressure : 10 kg/cm2 Make : Intervolve, Hawa / EquivalentInterconnecting pipe line for STP

SUPPLY OF INTER CONNECTING ELECTRICAL WORKS WITH PANELWITH AUTOMATION. Supply of Electrical works with following specifications Motor Control CentreType: Fixed cubical type with DOL Starters Consists of Incoming feeder with outgoing feeders, Voltmeter Ammeter, Push buttons with Indicator lamp, Overload relays, Contactors, Bus bar of required size, Control cabling Cables, Type : Copper: Make : Omega /Polycab Equivalent Terminations : Consists of compression cable glands,ferrules, ties, Panel for STP - Non compartment type. PLC for SBR Automation Included

ULTRA FILTRATION SYSTEM 200 KLD Supply , Installation , Testing and Commissioning UF feed pumps to transfer treated water from treated water tank to filters with following specifications, Mono block Centrifugal pump of capacity 10 cum/hr with 30 m head PUMP -Kirloskar / Equivalent 1Working + 1Stand By

BAG FILTER Supply , Installation , Testing and Commissioning Bag filter 1 Nos.(one working) Inline strainer / BaG filter of 50 micron before the UF system to protect the membranes from the coarse solids entering the UF process. Flow: 10 Cum/Hr MOC of housing : PP Make : Green Terra/Ion Exchange

ULTRA FILTRATION SYSTEM Supply , Installation , Testing and Commissioning Ultra filtration system to separate the treated sewage from TSS and turbidity to make it suitable for reuse in "Flushing" system the U.F. system shall consists of thefollowing: U/F: 10 Cum / day No of Membrane – 1 Lot Type: In to Out MOC: Modified polyether sulphone Sulphide / PVDF Polymeric Make: Hiflux / Team Type: Hallow Fiber

DOSING SYSTEM Supply , Installation , Testing and Commissioning Dosing system unit with pump etc., The unit shallcomprise of the following:One no. single moulded LDPE cylindrical tank of 100 litrescapacity having detachable lids with moulded inserts for mounting of pumpsOne no. Electronic diaphragm type positive displacement pumps . The electronic pump shall be operated on 220V single phase supply and shall be mounted directly on the tank top Make of Pump : E-dose/UKL/ Equal

UF Back wash Pump Supply , Installation , Testing and Commissioning UF backwash pumps to transfer treated water from UF treated water tanks to UF for backwashing purpose, withfollowing specifications, Mono block Centrifugal pump of capacity 25 cum/hr with 30 m headPUMP -Kirloskar / Equivalent1Working + 1Stand ByUF Back wash PumpUF backwash pumps to transfer treated water from UF treated water tanks to UF for backwashing purpose, withfollowing specifications, Mono block Centrifugal pump of capacity 25 cum/hr with 30 m head PUMP - Kirloskar / Equivalent 1Working + 1Stand By

ULTRA FILTRATION SKID: Supply , Installation , Testing and Commissioning MS fabricated UF skid with required supports and accessories for housing of complete Ultra filtration Unitincluding the control panel in SS 304 Make: Green Terra/Ion Exchange

PLC PANEL Supply , Installation , Testing and Commissioning The panel shall be PLC based and will have Voltmeter, Ammeter and indicating lamps on the incoming side only indicating lamps for the pumps on outgoing side toindicate the operation mode.

INTER CONNECTING PIPE Supply , Installation , Testing and Commissioning UPVC Pipes with schedule 40 for interconnecting from ss strainer to U/F membranes and include all ancillary items such as sockets, bends, elbows, tees, reducers, union, flanges, clamps/structural steel supports, hangers etc.,and making good finishes etc.

INSTRUMENTATION: Supply , Installation , Testing and Commissioning "Instrumentation “required for U/F system as mentionbelow.Flow meter : Rotometer, Maxflow makePressure gauge : As necessarysafety switch : 1 nos Valves : Pneumatic valves with actuator & necessary UPVC/GI valve

Sectioning the site including cutting and filling the undulations upto 15cm thick and levelling etc., complete in all respects as directed by the departmental officers.

Construction of granular sub-base 150mm thick by providing close gradad material,mixing in a mechanical mix at OMC carrage of mixed material to work site,spreading in uniform layers with motor grader on prepared surface and compacting with vibratary power roller ti achive the desired density complete as per clause 401 etc., complete in all directed by the departmental officers.

Providing and laying, spreading and compacting graded stone aggregate to Wet Mix Macadam 250mm thick specification including premixing the material (0.396 Cu.m of 45-22.4mm metal, 0.528 Cu.m of 22.4 - 2.36mm metal, 0.396 Cu.m of 2.36 mm size & below) with water at OMC in Mechanical Mix Plant Carriage and transporting the mixed mater by tipper to site, laying in uniform layers with pavers in sub base/base course on well prepared surface and compating with vibratory roller 8 to 10 tonne to achieve the desired density including cost of materials, labour charges, rental for machineries, fuel and other incidential charges etc., complete as per clause 406 of MoRT & H specifications. Rev-5 (Compaction by Vibro Max roller is a must)

Providing and laying Prime coat over WBM/WMM surface using 7 Kg of Emulsion Bitumen (SS1) per 10 Sqm for preparatory to another bituminous construction over it, including cost of material, labour charges, rentals for machinery, fuel and all other incidential charges etc., complete as per Clause 502 of MORTH Rev-5.

Providing and laying Tack Coat over WBM/WMM surface (treated with primer) using 2.50 Kg of Bitumen Emulsion (RS1) per 10 sqm for preparatoy to another bituminous construction over it including cost of material, labour charges, rentals for machinery fuel and all other incidental charges etc., complete as per Clause 503 of MORTH Rev-5 (Page 56)

Providing and laying 50mm consolidated thick Bitiminous Macadam using 0.20m³ of 26.50mm to 13.20mm graded metal and 0.43m³ of 13.20mm to 2.36mm graded metal, 0.08m³ of 2.36mm and below with 37kg of VG30/VG40 bitumen for premixing for 10m2 including cost and conveyance of all materials to CMP site, heating the bitumen and aggregates to required temperature and mixing them in required temperature in CMP 20 to 30 T capacity conveying the mix by tipper trucks to paver site, spreading the mix to uniform thickness of 50mm with mechanical paver to the specified grades and cross sections and consolidated by 8 to 10 T Vibratory/Pneumatic roller to the required density etc., including labour for attending to paver to site etc., including hire charges and fuel charges for 20 - 30 t CMP with bitumen boiler, tipper trucks, paver finisher/9m paver finisher, Vibratory/Pneumatic roller and all other tools and plant required, including all other incidential charges etc., complete as per specification using CMP clause 504 of MORTH Rev-5.

Providing and laying Bituminous concrete to30/ 40mm thick using 0.13 cum of 19.00-9.50 mm graded metal and 0.17 cum of 9.50-2.36 mm graded metal and 0.26 cum of 2.36 mm & below metal with 46.28 kgs of 60/70 bitumen & 4.02 Kg of Plastic waste (Total-50.30 kg) and for premixing per 10 sqm including cost and conveyance of all materials to C M P site, heating the bitumen and agregates to required temperature and mixing them in required temperature in central hot mix plant 20- 30 tonnes capacity conveying the mix by tipper trucks to paver site, spreading the mix in required temperature for uniform thickness of 40mm / 30mm with mechanical paver to the specified grades and cross sections and compaction by Vibratory roller to the required density etc., including labour charges for loading bitumen in to bitumen tank and metal to feeder unit,labour for attending to paver site etc., including hire charges and fuel charges for 20-30t C M P with bitumen boiler,tipper trucks, paver finisher, Vibratory rollers and all other tools and plants required,including all other incidental charges etc.,complete using C M P clause 507 of MORTH Rev-5 specifications.

Providing and laying of hot applied thermoplastic compound 2.5mm thick including reflectorising glass beads @ 250 grams per area, thickness of 2.5mm exculisive of surface applied glass beads as per IRC : 35 The finished surface to be level, uniform and free from streaks and holes.

Providing and laying precast saucer type drain of size 600x300 x 50mm with M30 GRADE concrete including the Cutting of the existing bituminous surface of 10 cm thicckness and PCC of 1:3:6 for leveling and maintain the gradient to drain the water from raod to Storm water Drain etc and complete

Supply and fixing of stored pressure ABC (Mono Ammonium Phospate) Powder Type Fire Extinguisher of 6 kg. capacity as per IS:15683 with pressure gauge, discharge hose & control nozzle, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc, complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT

Providing Depth Elevation work by shera wood board covering of size of 8mm thickness anchor box fixing with SDT top Screw in structural frame square tube of (40mm x 40mm size) and 1.6mm thickness including Structural material fabrication work and one base coat primer and two top coats of paint, complete as directed by the departmental officers.

Providing and fixing of Aluminium Composite Panel (ACP) 4 sided having 50 x 25 x 1.50mm frame work vertical and horizontals out of specially designed extruded sections withstand wind pressure of 180 Kg/sq.m and fabricated fixed at all level elevation and heights. The extruded section cutting and fixing required space extruded section shall be of 6063 and alloy of BSH 9 confirming T is – 63400 rate shall included to fix the main frame with necessary clamps, fasteners, bolt nuts etc. The main frame of extruded section shall be of 22843 & 22739 (H9) grade conforming to BS 4174 (or) IS 8147. Rate shall included 4mm thick ACP sheet (0.25 + 3.5 + 0.25) alstrong or equivalent fixing with spacer tape and the ACP sheet bounded with special type structural sealant of dow corning 789 or equivalent in dust free conditions the gaps between ACP sheet to be filed with whether sealant and backer rod or 12mm foam sheet to ensure water and air tightness in all complete complying with standard specification as directed by the departmental officer

Supply & stacking of red earth at site to the departmental gauge for premesurements which is of’ light textured , crystalline, porous and friable and no of generally acidic or neutral but not of alkaline and should be fertile, including seigniorage charges, cost of transportation, loading, unloadilig, stacking and inclusive of all taxes etc., complete.

Supply of well decomposed Farm yard Manure in a powdery form, devoid of soil sand, stones, plastics and other materials, highly nutrient and which supports plant growth. complete in all respects as directed by the departmental officers

Mixing charges of Red soil, sand and manure uniformly (1:1:1) for Preparation of soil mixture complete in all respects as directed by the departmental officers

Planting of Shade grass including loading and inloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc complete in all respects as directed by the departmental officers

Supplying and Planting of Pungam tree sapling of height 240 –300 cm in polythene bag of size 20x21 inch includingsupporting stack of 5 cm dia casurina pole of 10 feet height,including loading and unloading charges, transportation,stacking of saplings at site, earth work excavation of requiredsize, planting of sapling, refilling of excavated earth etc complete in all respects as directed by the departmental officers

Supplying and Planting of Golden Bamboo tree sapling ofheight 300 - 360 cm in polythene bag of size 15x16 inchincluding loading and unloading charges, transportation,stacking of saplings at site, earth work excavation of requiredsize, planting of sapling, refilling of excavated earth etc complete in all respects as directed by the departmental officers

Supplying and Planting of Neem tree sapling of height 240 –300 cm in polythene bag of size 20x21 inch includingsupporting stack of 5 cm dia casurina pole of 10 feet height,including loading and unloading charges, transportation,stacking of saplings at site, earth work excavation of requiredsize, planting of sapling, refilling of excavated earth etc complete in all respects as directed by the departmental officers

Supplying and Planting of Poovarasu tree sapling of height 240– 300 cm in polythene bag of size 20x21 inch includingsupporting stack of 5 cm dia casurina pole of 10 feet height,including loading and unloading charges, transportation,stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc asdirected by the site in-charge.

Supplying , stacking and planting of following plants of height 30-45 cm in polythene bag of dia 20 cm including loading and unloading charges , transportation, stacking of saplings at site, earthwork, of required size, planting of saplings, refilling etc., complete in all respects as directed by the departmental officers ORNAMENTAL SHRUBS Ficus black

Supplying , stacking and planting of following plants of height 30-45 cm in polythene bag of dia 20 cm including loading and unloading charges , transportation, stacking of saplings at site, earthwork, of required size, planting of saplings, refilling etc., complete in all respects as directed by the departmental officers ORNAMENTAL SHRUBS Ficus starlight

Supplying , stacking and planting of following plants of height 30-45 cm in polythene bag of dia 20 cm including loading and unloading charges , transportation, stacking of saplings at site, earthwork, of required size, planting of saplings, refilling etc., complete in all respects as directed by the departmental officers ORNAMENTAL SHRUBS Bamboo grass

Supplying , stacking and planting of following plants of height 30-45 cm in polythene bag of dia 20 cm including loading and unloading charges , transportation, stacking of saplings at site, earthwork, of required size, planting of saplings, refilling etc., complete in all respects as directed by the departmental officers ORNAMENTAL SHRUBS Acalypha

Supplying , stacking and planting of following plants of height 30-45 cm in polythene bag of dia 20 cm including loading and unloading charges , transportation, stacking of saplings at site, earthwork, of required size, planting of saplings, refilling etc., complete in all respects as directed by the departmental officers ORNAMENTAL SHRUBS Allamanda dwarf

Arm & Shoulder wheel Supply, Erection and Fixing of Arm & Shoulder Wheels 1300 x 1200 x1350 mm 4mm pipe Main Post made of 4 Inch Pipe and other main pipes 1-1/2 inch Pipes. 3 mm thickness pipes Double coat Powder coating, Heavy duty Branded sealed Ball bearing, for long lasting life as directed by the departmental officer.

ARM AND LEG STRENGTHENER Supply, Erection and Fixing of Leg and Arms muscle exercise. Strengthen joint and cardiovascular system. 1435 x 740 x 1005mm) 4mm Main Post made of 4 Inch Pipe and other main pipes 1-1 /2 inch Pipes. 3 mm thickness pipes. Thick Rexin covered cushioned Seat & Back rest Double coated Powder coating, Heavy duty sealed Ball bearing, for long lasting life as directed by the departmental officer.

TWISTER (TRIPLE) Supply, Erection and Fixing of LEG PRESS Size: 1500 x 1500 x1425 mm, Area of 7.4 Sq Ft Main Post made of 4 Inch Pipe and 26 I other main pipes 1-1 /2 inch Pipes. 3 mm thickness pipes. Double coated Powder coating, Heavy duty Branded sealed Ball bearing, Steel & foot rest / Foot Paddle for long lasting life. complete as directed by the departmental officer.

EXERCISING BAR Supply, Erection and fixing of Double Bar / Parallel BarFrame:1/2”GI pipe, 2.5mm thick, B class, height:41/2’,product size:6’*2’ paint: pu coating. complete as directed by the departmental officer.

ARM WHEEL (DOUBLE) Supply, Erection and Fixing of Arm Wheel of Size (1800 x 650 x 800 mm) Main Post made of 4 Inch Pipe and other main pipes 1-1/2 inch Pipes. 3 mm thickness pipes Double coated Powder coating, Heavy duty Branded sealed Ball bearing, for long lasting life as directed by the departmental officer.

Supplying, erecting and Fixing precast reinforcement benchwith back rest. Bench shall consist of 2 nos. L shaped basessupport in natural cement color of thickness 100mm, backheight 1000mm, front height 450mm, base width 620mm and5Nos Reinforced Concrete planks in red color and size of1500x100x50mm and 1no. reinforced concrete plank of150x200x50mm: manufactured by using M-30 grade concrete& reinforced suitably: all parts to be joined with galvanizednuts and bolts of suitable size as directed by the departmental officer.

Supplying and fixing of Rectangular Stone Pargola of size of 5' of width 8' of length and 9' of height as per standard specification as directed by the departmental officer. (The material should be got approve by the Executive Engineer before usage)

Supply and stacking of pit sand / earth filling sand at site to the departmental guage for premeasurements obtained from sand deposits and should clean whithout solid particles as directed by the departmental officer.

Spreading of red soil, gravel or sand including watering and rolling which hand roller for every 75 mm thickness - including hire charges of roller as directed by the departmental officer.

Supply, Erection and Fixing of Spiral Slide Senior FRP:[Component]Ladder :Galvanished ‘B’ Class pipeSlide : FRP Spiral slideBED LEG :Galvanished ‘C’ Class pipe [Measurement] Height :6 ½ ft.FRP thickness 6mm.(Reinforced Polymers in 7 Layers)450 CSM Matt, 600 Roving mat, Isotolic gel coat with UV pigment.Painting with PU coating width :10ft[Required area] Product area: 6’ft * 10’ft Play area :8’ft * 15’ft complete as directed by the departmental officer.

Supply and fixing of See-Saw 4 Seater FRP:Height :1 ½ ‘ft Width :5’ftFrame : 1 ½” Galvanished ‘B’ Class pipeSee saw Rail :2” Galvanished ‘C’ Class pipeSeat : FRP Seat with 450 CSM Mat 3 Layers bonding. Isotolic gel coat with UV pigment.Painting with PU coating seat size : 15”ft * 14”ft Product area : 5’ft * 10’ft Play area:8’ft * 12’ft complete as directed by the departmental officer.

Supply and fixing of Merry go round – 6 Seater (FRP)Height :3” GI Pipe, 2.5mm thick, b classSeat size:15” X 14”, paint: pu coating etc., complete in all respects as directed by the departmental officers.

Supply and fixing of Swing 2 seaterHeight of 7ft 0” above the ground level and width of 10ft 0”. Legs made of 40mm StainlessSteel pipes and Cross Bars made of 50mm SS pipes Seats fiber reinforced plastic seatssuspended with 6mm thick in coated chain etc. complete in all respects as directed by the departmental officers.

Testing the Ambient Air Quality & Monitoring - For parameters - PM-2.5 & PM-10, So2, NO2, CO at regular intervals as directed by the departmental officers.

Testing the Ambient Noise Quality Monitoring - To identify sources of noise, Noise due to traffic/transportation of vehicles ,Noise due to heavy equipment operations, Duration and variations in noise over time etc the equivalent noise levels shall be monitored as directed by the departmental officers.

Testing the Surface/Ground Water Quality - pH, Turbidity, Total Hardness at regular intervals as directed by the departmental officers.

Provisional Sum

ABIRAMI ENGINEERING CONSTRUCTION AND CO (BID ID -1052149)

GRM CONSTRUCTIONS (BID ID -1063689)

M/s Tharun Construction & Co (BID ID -1063373)