PROVN OF TOILETS BLOCKS IN BLDG NO P 32 03 TO 10 AND P 33 01 TO 07 NCSE QTRS OF 6 MECH INFT AT ZONE 08 UNDER GE BABINA AND SPL REPAIR OF PATHWAY AND GATE AT BHAGAT ENCLAVE AT BABINA CANTT UNDER GE BABINA

Amount

Excavation in trenches not exc 1.5 m wide and not exc 1.5 deep and getting out in any type of soil complete all as specified and directed.

Surface excavation n.exc 30cm deep, averaging 15cm depth and getting out in any type of soil.

M&L, moorum/Red Bajri filling in floors and pavings,spread, levelled watered and rammed in layers n.exc 15cm thick complete all as specified and directed.

M&L Walling of squared rubble stone masonry reqular curbed well bonded bedded and solidely heated built in cement mortar 1:6

M&L, Cement concrete (1:4:8) type D2 (using 40mm graded aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

Form work to soffits of suspended slabs such as roof slabs, floor slabs landing and similar work n exc 200 mm thick (horizontal sloping )

Formwork to edges of concrete in roof, chajja etc exc 10cm and n.exc 20cm wide complete all as specified and directed.

M&L, Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending for columns, hooking for columns, hooking ends and binding with and including mild steel wire(annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L, Mild steel bars 6 to 8mm dia, cut to length, bent to shape required, including cranking, bending for columns, hooking for columns, hooking ends and binding with and including mild steel wire(annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L, Mild steel bars 5mm dia & over upto and including 10mm dia, cut to length, bent to shape required, including cranking, bending for columns, hooking for columns, hooking ends and binding with and including mild steel wire(annealed) not less than 0.9mm dia or securing with clips as in stirrups complete all as specified and directed.

M&L RCC 1:1.5:3 type A-1 (using 20 mm graded BT stone aggregates) in foundations, footing, plinth beams, bases for columns and mass concrete complete all as specified and directed. (reinforcement to be measured separately).

M&L RCC 1:1.5:3 type A-1 (using 20 mm graded BT stone aggregates) in slabs supported on walls, beams & columns complete all as specified and directed. (reinforcement to be measured separately).

M&L RCC 1:1.5:3 type A-1 (using 20 mm graded BT stone aggregates) in roof beams, cantilevers,lintels etc complete all as specified and directed.

M&L, Brick work with sub class `B' bricks straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed.

M&L, Brick work with sub class `B' bricks straight or curved on plan exc 6m mean radius, built in CM 1:4, in half brick walls complete all as specified and directed.

M&L, Rendering 15 mm thick in cement mortar 1: 6 on fair faces of brick work finshed even and smooth without using extra cement complete all as specified and directed.

M&L, Flush pointing to random rubble masonry, uncoursed or brought upto courses in CM 1:4

M&L, Rendering 5 mm thick in cement mortar 1: 3 on celling / soffits of chajjas etc finished even and smooth without using extra cement complete all as specified and directed.

M&L, Rendering 5 mm thick on concrete surface of roof (top) in cement mortar 1: 4 mixed with WPC finished even and smooth without using extra cement complete when concrete is green complete all as specified and directed.

Supply only integrated water proofing compound

M&L, non-skid ceramic coloured tiles 7 to 8mm thick (square or rectangular) area of each tile exc 0.11 sqm and but n.exc 0.18 Sqm in floors etc laid over 15mm thick screed in CM 1:6 and 25mm thick PCC type B1 ( 1:2:4), set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L, for joint free glazed ceramic coloured tiles 7 to 8 mm thick (square / rectengular) area of each tile exceeding 0.11 sqm but not exc 0.18 sqm, in skirting/dado etc. set & jointed in cement slurry and pointed in white or coloured cement to match including 10 mm thick rendering in CM 1:4 finished rough for wall tilling etc complete all as specified and as directed

M&L, for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in coping on wall including necessary form work etc complete all as specified and directed.

S&F, Rotational moulded polyethylene water storage tanks 500 ltr capacity (cylindrical vertical with closed top) hoisted and fixed in position with ball valves 20mm PTMT complete (min weight 210 gms complete all as specified and directed.

S & F Angle stop valve of PTMT any colour high pressure screwed for iron pipe and fixed, (Minimum weight 15mm-90gms

S&F, Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe)

S&F, PVC valveless , syphonic action type, flushing cistern 10 ltrs capacity low level, white with inlet, ball valve float valve and handle including brackets complete all as specified and directed.

S&F PVC (SWR) Gully trap 125mm, setting and jointing with solvent cement complete all as specified and directed

S&F, (SWR) vent cowl 75mm complete all as specified and directed.

S & F Steel ventilator with top hung shutter including hinges steel peg stay, Handle, complete.

S&F, Bib taps, cast copper alloy chromium plated with crutch or butterfly handle (Long body), screwed down, screwed for iron pipe of bore 15mm complete all as specified and directed.

S&F, Stop valves, cast copper alloy, chromium plated with long shank and cup (concealed type) screwed both ends for iron pipe 15mm bore complete all as specified and directed.

S&F, in repair Swivel shower of chromium plated of size 80 mm fixed with 15mm bore pipe complete all as specified and directed.

S&F, in repair stop valve cast copper alloy screwed down high pressure with crutch or butterfly handle chromium plated angular type screwed both ends for iron pipe 15 mm bore or for unions and fixed.

S&F PVC (SWR) Floor trap plain with grating including jointing with solvent cement and fixed in repair 75 mm dia outlet.

S&F PVC SWR pipe 110mm bore in any length with rubber ring joint laid in floor and wall with necessary clamp complete all as specified and directed

S&F PVC SWR pipe 75 mm bore in any length with rubber ring joint laid in floor and wall with necessary clamp complete all as specified and directed

S&F PVC SWR bend any radius of size 110mm bore complete all as specified and directed

S&F, tubes medium grade GI with all fittings 15mm bore fixed walls complete all as specified and directed.

S&F, tubes medium grade GI with all fittings 20mm bore fixed walls or laid in floors as pipes complete all as specified and directed.

S&F, Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification.

S&F, Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement,

S & F Aluminium anodised, barrel tower bolts of extruded section and fixed 200mm complete all as specified and directed.

S & F Aluminum siliding door bolts, plate type, stove enamelled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts for on bolts plate and two on staple plate and fixed 300mm long etc complete all as specified and as directed

S&F, Butt hinges of size 100mm, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 as required at site complete all as specified and directed.

S&F, Aluminum handles cast type anodised 150mm complete all as specified and directed.

S&F, brass CP tubular towel rail 20mm dia `D' type 60cm long between flanges complete all as specified and directed.

M&L PCC 1:3:6 type C-2 using 40 mm stone aggregate as in foundation filling and mass concrete as in man holes septic tank soak well and drain complete all as specified and as directed.

M & L, cement concrete bed to drain pipe 1:3:6 type C-2 (using 40 mm graded stone aggregate) for 150 mm Internal dia of pipe, including packing under and haunching against side of pipe complete all as specified and as directed.

M&L applying water proofing treatment with the following:- (a) First coat of bitumen primer conforming to IS-3384 @ 0.4Kg / sqm (b) APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyester non woven fabric (wt not less than 150 gms/sqm) laid on primed surface by forced torched application complete all as specified (c) M&L for preparation of newly sufrace of app membrane and applying two coats of bituminious alumunium paint @ 200 gm per sqm etc complete all as specified and as directed

M & L Preparation of new steel surfaces over 10cm width or girth and applying two coats of synthetic enamel paints over a coat of red oxide complete all as specified and directed.

M&L Preparing new surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L Preparing new surfaces of wall and applying two coats of cement base paint complete all as specified and directed.

M&L Preparing new surfaces of wall and applying three coats of white wash complete all as specified and directed.

Removing excavated material to a distance n exc. 50mm and depositing where directed at alevel n exc 1.5mm above the starting point complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed..

S&F 20mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (Minium weight 210 gms ), complete all as specified and directed

S & F in repair 20mm dia Gun metal gate valve with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed.

Providing precast cement concrete 1:2:4type B1 (using 20mm graded stone aggregate) in in landings, cover slabs (for man holes, drain etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces

M & L Cement concrete type E2- 1:5:10 (using 40mm graded stone aggregate) as in subbase of floor.

M & L for concealed point wiring complete with PVC insulated and unsheathed flame retardant low smoke ( FRLS ) cable of 1.5 sqmm (nominal area) with stranded copper conductor single core 1100 volts grade in and including rigid PVC conduit not less than 20 mm dia, clip, with MS terminal boxes (not less than 1.0 mm thick) and painted with one coat of red oxide primer all around and two coats of black bituminous paint from out side and two coat of aluminum paint from in side including common earth dolly with 3 mm thick plastic laminated sheet top cover of approved make and colour including 1.5 sqmm green stranded copper conductor as continuous earth wire with lugs complete including cutting necessary chases on wall / ceiling surfaces for drawing of conduit & cables as required and making good disturbed surfaces of walls with CM 1:3:6 and matching with the existing surfaces including colour washing all as specified and as directed for the following. (a) One light point controlled by one switch

S&F switch piano flush type 5 Amp single pole one way complete all as specified and as directed.

S & F Lamp holder,PVC/Urea type with back plate suitable for batten fittings complete all as specified as directed

S&F ceiling rose,surface bakelite 63 x50mm three terminals complete all as specified and as directed.

S&F for sub main wiring with PVC insulated, unsheathed 2 single core cable 1100 volts grade with copper conductor of size 2.5 sq mm (Nominal area) multi stranded drawn into conduit (Existing / new) with and including 1.5 sqmm green stranded copper conductor as contineous earthwire with lugs complete all as specified and as directed. Note: New conduit and conduit accossories shall be measured separately.

S & F Regid non-metallic PVC conduit not less than 19 dia (external) ISI marked (on surface) incl of all accessories and all fittings such as Tees,bends, elbows, reducers, bell mouth, tube ends and fixing accossories such as couplers,lock nuts, saddles, pipe hook etc complete all as specified and as directed

S&F sheet metal enclosure double door suitable for distribution boards when MCBs to be used having 100Amp rated bus bar SPN,2 ways 240 V complete all as specified and as directed.

S&F MCB SPN 6 to 40 Amps 240 V,10KA, 'C' series,complete all as specified and as directed with copper lugs

Supply and fixing in repair 18/20 W LED 6000k Decorative ultra slim linear LED fitting fixture with extruded polycarbonate ,environmental friendly ,energy efficentinterated driver and 20 watts lamp fitted including wiring upto and terminal into existing ceiling rose complete all as specified and directed by Engr-in- Charge. Make havells cat part No HavellsENDURALINEARNEOBS20WLED865SPCWH 020 or equivelent in philips/bajaj /CG.

S & F LED bulb1x9 watt having PF not less than 0.90 suitable for holder fittings complete all as specified and directed. (Make : Philips/Surya/Bajaj/Crompton greaves).

Supply ,laying and testing cable XLPE insulated screened PVC bedded ,galvanised steel strip armoured ,electric power cable (heavy duty ) 1100 volt grade with stranded aluminium conductor of size 06sqmm 2 core complete all as spd and directed.

supply laying dry clean sand free from sharp materials, unscreened filling in trenches around under ground cables for cushioning complete all as specified and directed.

M&L for brick protection covers over cables of sub class B bricks old size , laid dry over cables (length of bricks shall be laid across the length of the cable complete all as specified and directed

M&L pipe galvanised iron, light grade ISI marked, complete with fittings laid inj trenches/ fixed with poles etc as protection to cables complete as ditrected by Engineer in Charge for the size 32 mm dia

M&L for earthing complete with galvanised steel earth plate electrode of size 600 mm x 600 mm x 6 mm thick weithing not less than 17.5 Kg buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below ground level, connected to galvanized earth lead wire 4.00 mm dia by means of bolts nuts check nuts & washers of galvanized iron or steel , procteded by GI pipe 15 mm bore( light grade) and watering pipe 20 mm bore GI pipe (light grade) and chamber of pcc 1:4:8 type D2 using 40 mm graded stone aggregate and coping shall be in PCC 1:3:6 type C1 using 20mm graded stone agg. 50 mm thick cover of RCC 1:2:4 type B1 using 20 mm graded stone agg. reinforced with 8 mm dia MS tor bar @ 80 mm c/c both ways including excvation and earth work and removal of surplus soil complete all as shown in electrical plate no 3 of SSR PT 1, 2010 with charcoal dust and salt complete and earth lead connected to earthing test point (up to main switches, DBs) complete all as specified & testing on completion. NOTE:- (I) item includes the cost of 7.5 mtr length GI pipe for protection for GI earth wire. (ii) item rates includes the cost of 7.5 mtr earth lead GI earth wire. (iii) PCC pit shall be provided at least 500mm away from the pit and not on the earth pit itself and the extra cost of additional length of watering pipe,bends,elbow etc shall be deemed included in the unit rate.

Demolition of PCC in ground floor & pavings not exc 15 CM thickness below or above ground level etc complete all as specified and as directed

M&L, PCC 1:4:8 type D2 using 40mm graded stone agg as in filling and mass concrete, Sub base/flooring complete all as specified and directed.

M&L, sand cushioing to under concrete interlocking paver block including watering & consolidation complete all as specified

M&L 60 mm thick machine pressed precast concrete interlocking paver block any shape & size confirming to IS 15658-2006 of 60mm thickness, M-35 grade with grey cement & pigment.

M&L, for PCC 1:2:4 type B-1 using 20mm graded stone agg as in kerb complete all as specified and as directed.

M/s Ravi Traders

M/S M S Constructions

Hansraj Shivhare

G.R.associates

M/S DEVINDER ENTERPRISES