SPECIAL REPAIR TO BLDG NO. P-260/13 AND 14, P-219/01 TO 04 AND PROVN OF GENERATOR SET SHELTER, BATHROOOM , URINAL POINT AND TOILET BLOCK AT SANGRUR UNDER GE (SOUTH) PATIALA

Amount

'Notes: (i) Please refer Schedule 'A' Notes of tender documents.

Taking down cement or cement lime plaster on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc.complete all as specified and directed.

Supplying & applying for two component elastomeric acrylic polymer modified cementitious waterproofing coating on Brick wall, SmartCare Damp Block 2K or approved equivalent, having 100% elongation as per ASTM D412, resisting 5 bars hydrostatic pressure as per DIN 1048, reduction to rapid chloride shall be 70 as per ASTMC1202, crack bridging up to 1.2mm as per ASTM 4548.5. The coating shall have food grade certificate from laboratories like CFTRI, will be apply on both Positive & Negative side and resist up to 5 Bars of Hydrostatic Pressure. The mixing ratio of the coating shall be 2 parts of powder & 1 part of liquid without any water addition in the mixing, etc. After coating will sprinkle Sand on the coating then apply plaster on the coating complete all as specified and directed. NOTE: (i) Cost of steel props adjustable (suspended/supported) scaffolding (6m to 7m) height, safety equipment for labours (Belt, Hook & Helmet) shall be deemed to be included in the unit quoted rate. (ii) Rendering plaster will be measured and paid separately.

M&L for Providing mixing & applying two component Epoxy resin concrete bonding coat on prepared RCC surface as per manufacturer instruction including preparation of surface by chipping and throughly cleaning of surfaces complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces with CM 1:4 finished even and smooth without using extra cement in external surfaces WPC shall be mixed complete all as specified and directed. NOTE-WPC Shall be measured and paid Separately

M&L 10mm thick cement plastering in cement mortar 1:6 finishing the surface even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5mm thick in cement mortar 1:3 as on concrete surfaces in ceiling finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of new plastered or unplastered surfaces of walls, two coats of cement base paint complete all as specified and directed.

M&L for preparation of new plastered or unplastered surfaces of walls and applying two coats of distemper oil emulsion complete all as specified and directed.

M&L for preparation of new plastered or unplastered surfaces applying three coat of white wash on ceiling surfaces complete all as specified and directed.

M&L for complete removal of existing treatment of any type/description such as distempering work ,internal emulsion etc from internal/external surfaces of walls & ceiling with mechanical means/grinder including removal of material from site complete all as specified and directed.

M&L for preparation of old plastered or unplastered surfaces of walls, two coats of cement base paint complete all as specified and directed.

M&L for preparation of old plastered or unplastered surfaces of walls and applying two coats of distemper oil emulsion over complete all as specified and directed.

M&L for preparing old plastered surfaces of ceilings and applying one coat of white wash complete all as specified and directed.

Dismantling of brick work built in cement mortar incl all quoins, arches, pillar etc complete all as specified and directed.

M&L for brick work with Fly ash bricks straight or curved on plan exc 6 mtr mean radius built in CM 1:6 complete all as specified and directed (as in manhole).

M&L for brick work in cement mortar (1:4) using sub class 'B' bricks straight or curved on plan to any radius but in half thick brick walls complete all as specified and directed.

Taking down chowkhats or frames (without taking off shutters from the frame) exc 1.5 Sqm and n. exc 4.00 Sqm incl cutting holes and making good reqd shape for hold fast block for new frame complete all as specified and directed.

All as per srl item No. 18 hereinbefore but n. exc 1.5 sqm each complete all as specified and directed.

S&F Pressed steel frames made of MS sheet of 1.25 mm thickness for doors with single rebate including necessary fixing lugs, hinges, lock strike plate, complete as specified, size 105x 60mm complete all as specified and directed. Note :- Disturbed portion of existing floor /wall / tile / plaster etc during fixing of chowkhats shall be repaired to match with existing finish. Cost of the same will be included in this item .

S&F Pressed steel frames made of MS sheet of 1.25 mm thickness for doors with double rebate including necessary fixing lugs, hinges, lock strike plate, complete as specified, size 125x 60mm complete all as specified and directed. Note :- Disturbed portion of existing floor /wall / tile / plaster etc during fixing of chowkhats shall be repaired to match with existing finish .Cost of the same will be included in this item .

M&L Plain cement concrete (1:3:6) type C-0,using 12.5 mm graded mechanically crushed stone aggregate as in back filling of pressed steel frame /hold fast blocks etc and similar complete all as specified and directed.

S&F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F 35mm 2nd class hard wood Glazed and skeleton shutters, 2nd class hard wood open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkhats complete all as specified and directed.

S&F Aluminium, anodised, barrel tower bolt 200mm long of extruded section and fixed complete all as specified and directed.

S&F for 300mm aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts complete all as specified and directed.

S&F Extruded aluminium alloy handles, fabricated type, anodised 150 mm size complete all as specified and directed.

S&F Mild steel butt hinges of size 100mm medium weight cold rolled complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue ,anodised with hard drawn steel spring fixed in floor overall length of cover plate 140mm complete all as specified and directed.

S&F 300 mm long MS rat tail pattern spring hinge (helical door spring) including roller and roller plate, complete all as specified and directed.

Providing and fixing factory made extruded aluminium casement windows with 50 micron powder coating doubled panelled and double shutters consisting of frame and mullion of 101.60X44.45X1.29 mm and shutters made of 63.5X31.75X1.29mm and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size with and including 5mm thick glass in front shutters and stainless steel wire gauge 0.36mm dia and 1.40 aperture in inner shutters complete fixed in all respect as specified including supply and fixing following items :- (a) Stainless Steel (304 Grade) Finished Butt Hinges 150mm - 2 nos per leaf. (b) Powder Coated Aluminium Tower Bolt 150mm long - 2 nos per leaf. (c) Powder Coated Aluminium Handles 150 mm - 1 nos per leaf. (d) Note:- For Cooler fixing arrangement 08 nos shutter Each window.

S&F Aluminium anodised DG 102 "DECO" grill of size 100mm x 10mm x7mm thick, approved design for windows / ventilators with and including F/U channel, complete all as specified and directed.

Providing and fixing factory made extruded aluminium ventilators with 50 micron powder coating of frame of 63.5 X 38.10 X 1.29 mm including 5mm thick frosted glass in lower 55% portion of shutters and stainless steel wire gauge 0.36mm dia and 1.40 aperture in upper 45% portion of shutter and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size with and complete all as specified and directed.

M&L for Steel cup board shutter made out pressed steel frame of size 75mmx45mmx1.25mm thick with pressed steel shutter 01mm thick Godrej pattern fixed to masonry wall by hold fasts made out of 25x3mm flat iron including mild steel CP hanging rod of 20mm dia with brackets fixed on inner side of one leaf of shutter and on other leaf provision of mild steel CP peg set of 3 including spray painting with two coats of synthetic enamel paint over one coat of red oxide primer all around on steel surfaces of frame and shutter including taking down existing wooden cup board and making good disturbed portion in CM 1:3 or PCC 1:2:4 all as specified and directed. 1.25 mm thick in frame work, cut to size, holes punched, welding, riveting, turning, bending etc. as require to made it in Godrej pattern complete all as specified and as directed.

S&F Wire netting of galvanised steel wire 1.40mm dia and size of mesh 25mm fixed with wooden beds tinned tacks of wire staples complete all as specified and directed.

M&L for preparing of new surface of wood and wood based material of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel pain and one coat of pink primer complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings n exc 15cm thickness (below or above ground level), complete all as specified and directed.

Dismantling of floor or wall tiling including cement mortar bedding but not backing and removing the rubbish off the premises complete all as specified and directed.

M&L 40 mm thick PCC (1:2:4) type B-0 using 12.50 mm graded crushed stone aggregates in complete all as specified and directed.

M&L for ceramic coloured tiles 10 mm thick (square/rectangular) area of each tile n.exc 0.38 Sqm as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match as in skirting over and including 15mm thick screed bedding in CM 1:6 complete all as specified and directed.

M&L for Non Skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over a screed bed of 15 mm thick in CM 1:6 complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 450X 300X 7mm thick over and including 10 mm thick rendering in cement mortar 1:4 as in backing coat for tiles on vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L for Pre polished chequered cement concrete tiles 30cmx30cmx25mm thick, set, jointed and pointed and in need cement slurry in floor with grey cement and pigment and including over screed bed or bedding layer of mortar 20 mm thick laying floor finished in cement mortar 1:6 complete all as specified and directed.

M&L for Plywood (12mm thick no of ply 07 nos ) grade BWR, type BB, fixed with screw to timber frame-work fixed complete all as specified and directed.

S&F Decorative type lamination type -1 of surface finish, colour and pattern as approved including fix with approved adhesive (thickness of lamination sheet 1.5 mm.) complete all as specified and directed.

M&L for 30 mm ( width of flaps when open) continuous (Piano) hinges, mild steel, bright finish or electro galvanised complete all as specified and directed.

S&F Rim latch (75 mm of size) with two levers of mild steel body, stove enamelled finish with brass knob or lever handle and fixed complete all as specified and directed.

S&F extruded brass handles fabricated type polished (size of handle 75 mm) complete all as specified and directed.

M&L Clean Sawn Timber framed and fixed in Second class Soft wood Scantlings as in Wall/Ceiling complete all as specified and directed.

M&L 2nd class softwood not exc 3 Sq cm Plain Fillets, square, Rectangular or triangular in sec, clean swan, Secured with nails or brads complete all as specified and directed.

S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe over all size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

Taking up or down steel tubing of size15mm bore and removal to store complete all as specified and directed.

Taking up or down steel tubing of size 20mm bore and removal to store complete all as specified and directed.

Supply and laying of 20mm outer dia CPVC pipes SDR11 & plain CPVC SDR 11 fitting fixed on wall / celling or laying in floor complete all as specified and as directed.

Supply & laying of 25 mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 with and incl fittings fixed on walls/ceiling or laying in floors complete all as specified and directed.

Supply & laying of 32mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 with and incl fittings fixed on walls/ceiling or laying in floors complete all as specified and directed.

S&F in repair Stainless steel chromium plated 20mm curtain rod with fixing brackets, stops rollers complete incl fixing brackets, stops etc complete all as specified and directed. Note:- For the purpose of measurement and payment running length of curtain rod only shall be considered.

Dismantling of brick tiles or terracing tiles single layer on roofs complete all as specified and directed.

Demolition of mud puska on roof any thickness complete all as specified and directed.

M&L for roughening surfaces of old concrete floor by picking, sweeping cleaning and washing down with water to remove dust, etc complete all as specified and directed.

M&L for PCC 1:3:6, type B-0 using 12.5 mm graded stone aggregates as in padding over roof ,minimum thickness at khurra as 25mm maintain a slope of 1:100 using water proofing compound complete all as specified and directed.

M&L for cutting grooves in brick wall ,75 mm wide and 65 mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and directed.

M&L for PCC 1:2:4, type B-0 using 12.5 mm graded stone aggregates as in roof kerbs or mud stops/ coping etc including weathering slightly rounded or chamfered complete all as specified and directed.

M&L for providing and laying 3mm thick APP (Atactic Polypropylene Polymer) modified prefabricated five layer, weight not less than 3.60 Kg/Sqm water proofing membrane black finished, reinforced with non-woven polyester matt make as approved including of a coat of bitumen primer confirming to IS-3384 and as described at para 11.44.5 of MES Schedule Part-I @ 0.40 ltr/sq.m by the same membrane manufacturer of density 0.87 to 0.89 Kg/Ltr at 25 degree C temperature and viscosity 70 - 160 cps Over the coat, 3mm thick 5 layered APP membrane shall be laid using butane torch and sealing all joints etc after the surface complete as per standard practice as per manufacturers instructions including 15mm thick cement plaster (1:3) using coarse sand mixed with integral liquid water proofing compound shall be provided while the concrete of roof slab is green and finishing surface even and smooth with steel trowel complete all as specified and directed. Note : The vital physical and chemical parameters of the membrane shall be as under - (i) Joint strength longitudinal and transverse direction at 23 degree C as 650/450N/5cms (ii) Tear strength in longitudinal and transverse direction as 300 / 250 N/. Softening point of membrane not less than 150 degree C Cold flexibility upto 20 degree C when tested in accordance with ASTM (D05147) (iii) The laying of membrane shall be got done through the authorised applicator of manufacturer of membrane only complete all as specified and directed.

M&L cement concrete tiles 20-22 mm thick , type B-1 type (1:2:4) pointed in neat cement slurry over 15mm thick screed bed in CM (1:4) complete all as specified and as directed.

S&F Cooler stand Joist, channel, angle, or tee sections, fixed independently, without connecting plates, conforming to Fe 410-W (Gde-E-250) quality -A complete all as specified and directed.

S&F framed work as in doors or gates of angles or other section with gussets plate rails braces etc complete drill for fixing of steel sheeting or other covering. Doors etc to be prepared for hanging or sliding with and incl either hook and hinges or steel hanging door fitting steel sheeting or other covering, running rails and hanging also fastening and fixing complete incl hinges, stops hand made sliding bolts etc conforming to Fe 410-O or Fe 310-O, including taking down old steel gate complete all as specified and directed.

M&L for preparing surfaces of any description over 10 cm girth or width, not otherwise described and applying two coats of synthetic enamel paint over a coat of Red oxide on new surfaces of steel or iron, complete all as specified and directed.

M&L for PVC ( SWR) rain water pipes 110 mm bore single socketed in any length with rubber ring joints fixed to walls complete as specified including flat iron clamps 25x3mm including taking out old damaged AC rain water pipes complete all as specified and directed.

M&L for PVC (SWR) bends of any radius for 110 mm dia rain water pipes with rubber ring joints complete all as specified and directed.

Dismantling 500ltr water storage tank complete all as specified and directed.

M&L for rotational moulded polythene water storage tank cylindrical vertical with closed top 500ltr capacity hoisted and fixed in position incl 20 mm bore ball brass valves high pressure with polythene float and fly nut all as specified in SSR Part-1 complete all as specified and directed.

S&F 125mm Brass chromium plated shower rose with arms complete all as specified and directed.

S&F in repair CP stop cock concealed cast copper alloy with crutch screwed down screwed for brass ferrule for 15 mm bore pipe after of any description complete all as specified and directed.

S&F Bib taps for 15 mm dia bore pipe cast copper alloy chromium plated with capstan head screwed down for iron pipe or brass ferrule and fixed complete all as specified and directed.

S&F in repair Brass CP mixer for mixing hot & cold water screwed down for iron pipe 15mm bore complete all as specified and directed.

S&F in repair wall mixer hot and cold mixture Cast copper alloy fancy type 15mm bore , with capstan heads chromium plated screwed down high pressure and fixed complete all as specified and directed.

S&F in repair angle stop valve(Concealed type) cast copper alloy chromium plated with capstan head , long shank and cup screwed down screwed for iron pipe or for brass ferrule for 15 mm bore pipe of any description complete all as specified and directed.

S&F Angle stop valve(Concealed type) cast copper alloy chromium plated with capstan head , long shank and cup screwed down screwed for iron pipe or for brass ferrule for 15 mm bore pipe of any description complete all as specified and directed.

S&F 20mm Stop valves/ gate valve , cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F for Pillar taps bore dia 15 mm (fancy type), cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F 450 mm long PVC connection with brass nuts on both ends for 15mm bore pipes of approved quality complete all as specified and directed.

S&F Vitreous china, wash hand basin, white, flat back, size 550x400mm including PVC waste pipe 32mm bore and mild steel brackets, fixed all in repairs, including cutting for or pinning in brackets complete all as specified and directed.

S&F Tubular towel rail, CP 20mm dia, 60cm long between flanges complete all as specified and directed.

S&F Shelf of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms) complete all as specified and directed.

S&F low level flushing cistern of PVC 10 ltr capacity incl 45cm long PVC connection with brass nut at both ends, 15 dia stop cock cast copper alloy, screwed both ends, high pressure(wt not less than as specified in SSR), PVC flush pipe 32 mm bore complete all as specified and directed.

S&F Vitreous china ware wash down water closet Pedestal pattern with P trap including connection to flushing pipe, anti siphonage pipe complete all as specified and directed.

S&F in repair glass self assembly consisting of 5.5 mm thick sheet glass self 12 cm wide with chromium plated bracket guard and railing 60 cm long any size including fixing complete all as specified and directed.

S&F in repair Soap dish approx size 160x160x90mm any type including fixed to plugs with CP brass screw complete all as specified and directed.

S&F for 15mm bore Health faucet with CP flexible pipe of 1.25metre long incl making connection and fixed in position complete all as specified and directed .

S&F in repair 32mm bore waste fittings brass chromium plated for glazed ware sinks basins etc with long screwed shanks and fly nuts, flange and bedded in red lead cement and other end fixed complete all as specified and as directed.

S&F in repair PVC waste pipe 32mm dia complete all as specified and directed.

M&L PCC (1:3:6) type C-1 (using 20 mm graded aggregate) as in PCC path/ plinth protection 75mm thick. finished the surfaces even and smooth with out using extra cement complete all as specified and directed.

Demolition of reinforced cement concrete of any description (Reinforcement cut as required to facilitate demolition) complete all as specified and directed.

M&L for reinforcement cement concrete (Normal mix )1:1.5:3 Type B1 (20mm graded aggregate) as in slab support on wall , beams and column in floor roof landing balconies deck slab and in shelves and the like ( MUMTY and BALCONY) complete all as specified and directed. Note : Cost of Steel props adjustable (Suspended/Supported) Scaffolding (6m -7 m) Hight , safety equipment for labours (Belt, hook, Helmet) shall deemed to be included in quoted rates .

M&L for reinforcement cement concrete (Normal mix )1:1.5:3 Type B1 (20mm graded aggregate) as Chajja and the like complete all as specified and directed.

M&L for TMT bars 10mm dia and over mild steel as in reinforcement, cut to length bent to shape required including cranking and bending with MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L Granite 20mm thick (of Z Black) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking plat?forms and like in white cement with admixture of pigment to match with shade of granite stone including grinding and polishing complete laid over and including 15mm thick screed bed or bedding layer in CM(1:4) , complete all as specified and directed.

M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations

M&L for Pre polished Machine cut Kota stone slab flooring 20-25mm thick laid over and including 15 mm thick screed bed or bedding layer in cement mortar 1:4 as base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed. Note : in Steps Single piece only used

S&F mild steel powder coated peg set of 6 fixed to wall with steel screws complete all as specified & directed.

S&F Stainless steel wall mounted kitchen wire rack of size 750mm X600mm X 250 mm complete all as specified and directed.

S&F in repair cast iron sand cast soil waste & vent pipe in any length with or without ears with cement joints laid in trenches or in floor of 100 mm bore with sand cast paper complete all as specified and directed.

S&F in repair cast iron 100mm sand cast vent cowl with cement joints bore with sand cast paper complete all as specified and directed.

S&F in repair CI floor trap with grating including jointing to waste pipe in neat cement 75 mm dia fixed in cement concrete (1:2:4) type B1 complete all as specified and directed.

S&F in repair CI P & S trap with grating including jointing to waste pipe in neat cement 100 mm dia fixed in cement concrete (1:2:4) type B1 complete all as specified and directed.

S&F in repair 100mm bore CI Bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and directed.

S&F in repair 100mm CI Branch pieces, double/cross, T (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed.

S&F in repair 100mm bore Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed.

S&F for Solid PVC door frame of size 50 mmx47 mm made out of 5 mm plain colour PVC sheet re-inforced with M.S square tube, supplying and fixing in opening as per specification and drg complete all as specified and directed.

S&F for factory made solid panel PVC moulded door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour of PVC sheet for top rail lock rail and bottom rail, on either side & gap insert for top rail bottom rail panelling of plain colour PVC sheets to be fitted in MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F for butt hinges medium weight cold rolled mild steel 75mm complete all as specified and directed.

S&F for 100 mm aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F for 100 mm long anodised extruded aluminium alloy handles (D type), fabricated type complete all as specified and directed.

Demolition of cement concrete any description and any position not otherwise specifically provided (below or above ground level) complete all as specified and directed.

M&L for plain cement concrete 1:7:12 mix, type E-2 (using 40mm graded Brick aggregate) as in filling of sunken portion complete all as specified and directed.

M&L for applying three coats of brush bond acrylic based cementitious material of approved quality for sunken portion treatment all as per manufacturer instruction and providing 3 mm thick APP membrane over 85/25 grade bitumen layer @ 0.5 kg /Sqm complete all as specified and directed.

M&L for providing 40 mm dia GI pipe medium grade spouts 50 Cm long complete all as specified and directed.

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, finshed flat rough finished surfaces etc. complete all as specified and directed.

M&L for Formwork to chullah hoods, chajjas, troughs and similar items including edges, finished flat rough finished surfaces etc. complete all as specified and directed.

S&F in repair Gun metal globe or gate valves of 20 mm dia with iron wheel head screwed both ends for iron pipe complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out soft/loose soil complete all as specified and directed.

M&L for PCC 1:3:6, type B-1, using 40mm graded stone aggregate as in foundation for post holes, complete all as specified and directed.

Excavation in trenches n exc 1.5m wide and n exc 1.5m in depth for foundation including getting out in soft/loose soil for foundations etc. for shafts, wells, cesspits. Manhole, pier holes, etc complete all as specified and directed.

S&F for pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed to self tapping screws complete all as specified and directed.

M&L for rectangle / Square /circular hollow section as in main and cross beams, hip and jack rafters purlins, where connected to common rafters and running rails and guides for structural purpose, fixed with angle cleats or other connecting plates to Fe-290 (Gde E-165) complete all as specified and directed.

M&L for Hard core of broken stone boulders of gauge 40 mm spread and levelled in layers n exc.15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for Providing, cement concrete Type C1 1:3:6 (20mm graded aggregate) in plinth, Coping rounded or chamfered on edges complete all as specified and directed.

M&L for PCC 1:2:4, type B-0 using 12.5 mm graded stone aggregates as in coping , bed plate and the like including weathering slightly rounded or chamfered angle and throating as directed including provision of necessary form work and finish exposed surface even and smooth without using extra cement complete all as specified and directed.

M&L for 100mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in sub base of flooring complete all as specified and directed.

Supply only integral water proofing compound ISI marked complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in sub base of flooring, complete all as specified and directed.

M&L for machine pressed precast concrete inter locking paver block any shape and size made of M-35 grade concrete (with grey cement and no pigment) of 60mm thickness with 6mm top layer of anti abrasive material laid over 25mm thick (compacted) fine sieved sand complete all as specified and directed.

M&L for returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25 cm thick in soils complete all as specified and directed.

M&L for removing excavated material(soil) to a distance not exc 50mm and depositing where directed at a level n.exc 1.50m above the starting point complete all as specified and directed.

M&L for PCC 1:4:8, type D-2 using 40mm graded stone aggregate, as in foundation etc. complete all as specified and directed.

M&L 40mm thick 1.2.4 type B-0 Damp proof course to horizontal or vertical surfaces including necessary formwork complete all as specified and directed.

M&L for Non Skid coloured tiles 7 to 8(square/rectangular) area of each tile exc 0.06Sqm but not exc 0.11sqm in flooring etc set and jointed in neat cement slurry and pointed in white cement to match over and including 15mm thick screed bed in CM (1:4) laid complete all as specified and directed.

M&L for Coloured glazed ceramic tiles (300 x 600 mm) x 7mm or (300 x400 mm)X7mm thick as in vertical surfaces such as skirtings, dados etc jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 10mm thick back coat in CM (1:4), complete all as specified and directed.

M&L for PCC (1:3:6), 50mm thick using 20mm crushed stone aggregate as in PCC path/ plinth protection finished the surfaces even and smooth with out using extra cement complete all as specified and directed.

M&L for brick work in cement mortar (1:4) using Fly ash bricks straight or curved on plan exc in half brick thick wall complete all as specified and directed.

S&F PVC (SWR) Sewage pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors of 110 mm bore complete all as specified and directed.

S&F PVC (SWR) Sewage pipes single socketed, in any length with rubber ring joints, fixed to wall of 110 mm bore complete all as specified and directed.

S&F PVC (SWR) 110mm bore Bend complete all as specified and directed.

S&F PVC (SWR) 110 mm vent cowl complete all as specified and directed.

S&F in repair PVC (SWR) junction double, (double T), equal or unequal 110 mm with parallel branch complete all as specified and directed.

S&F PVC P & S trap with grating including jointing to waste pipe 110 mm dia fixed complete all as specified and directed.

S&F PVC(SWR) Floor trap 75mm plain with CP grating including jointing to wate pipe with solvent cement complete all as specified and directed.

S&F Reinforced concrete pipes, class NP2 laid and jointed complete with collars bore in pipes 150mm complete all as specified and directed.

M&L for150mm bore, cement concrete bed 1:3:6 type C2, using 40mm graded stone aggregate to drain pipes including packing under and haunching against the sides of pipes after they are laid and fitted complete all as specified and directed.

M&L for PCC 1:2:4, type B1, using 20mm size graded stone aggregates as in bands, copings, etc., including necessary formwork complete all as specified and directed.

S&F for 150 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams,sides and soffits (if any) of foundation and plinth beams and similar work; vertical or to batter complete all as specified and directed.

S&F Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

S&F Formwork to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

M&L for Reinforcement cement concrete in nominal mix 1:1.5:3 in foundation, including raft footings, foundation beams, plinth beams, bases for column etc., basement slabs, underreamed piles and mass concrete complete all as specified and directed.

M&L for Reinforcement cement concrete in nominal mix 1:1.5:3 in Beams, cantilevers,lintels, columns pillars, piers, posts, struts, chullah hoods, stair case,arches, domes, vaults, shell roofs, arch ribs, folded plates, slabs, balconies, canopies, deck slabs etc. or in similar articles upto 5th floor level complete all as specified and directed.

Mild steel TMT bars cut to length, bent to shape required including cranking, bending and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips but 5 mm dia and over upto and including 10 mm dia in stirrups,spacers and binder complete all as specified and directed.

S&F Vitreous China Urinal, Half stall type,white (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and directed.

Taking down carefully copper/ aluminium point wiring (light fan socket or power) complete along with fittings such as switches, ceiling roses, Pendants, regulators, Tube fittings and other Kits & fittings/conduit from surface /wall .Removing the material from work site and making good the disturbed portion/ surface of wall/ floor/ ceiling etc by using cement mortar and colour/ white wash to match with the existing surface / location complete all as specified and directed. Note ;- Serviceable fitting / fixtures will be reused in the work as directed by Engineer- in-Charge

Taking down un-serviceable main switch, DB’s insulators, DB for MCB etc of any type and any capacity and further disposal including making good the disturbed surface and matching the colour of wall with the existing colour wash / paint / distemper wherever required (as per the existing ) complete all as specified and directed.

M&L for taking down ceiling fan of any descriptions, servicing, rewinding, and complete repairs, painting of fan as required, fixing back, ceiling fan for proper functioning, Including connecting and testing the fan for its satisfactory function including making good the disturbed surface and matching the colour of wall with the existing colour wash / paint / distemper wherever required (as per the existing ) complete all as specified and directed.

M&L for taking down exhaust fan of any descriptions, servicing, rewinding, and complete repairs, painting of fan as required, fixing back, exhaust fan for proper functioning, Including connecting and testing the fan for its satisfactory function including making good the disturbed surface and matching the colour of wall with the existing colour wash / paint / distemper wherever required (as per the existing ) complete all as specified and directed.

M&L for taking down elect water heater of any descriptions, servicing and complete repairs of geyser as required, painting outer body, fixing back, connecting and testing the geyser for its satisfactory function including making good the disturbed surface and matching the colour of wall with the existing colour wash / paint / distemper wherever required (as per the existing) complete all as specified and directed.

M&L for point wiring with FRLS PVC insulated unsheathed multi-stranded copper conductor 1.5 Sq.mm (nominal area ) single core cable 1100 Volt grade drawn in and Including new rigid non metallic concealed PVC Conduit of suitable size (not less than 20 mm) in wall , surface of ceiling with all fittings, such as tee, bend, elbow, socket etc including pressed steel sunken boxes (Terminal boxes) with earth dolly, duly galvanised, with white shade frame & cover plate of suitable module for modular switch / or sockets including FRLS PVC insulated unsheathed stranded copper conductor 1.5 Sq.mm (nominal area) single core cable as earth continuity conductor to common earth and connected to earth dolly, Including making good the disturbed portion of the wall complete all as specified and directed. for the following :-

One light/fan point controlled by one 1-way switch complete all as specified and directed.

One light/fan point controlled by two 2-way switch complete all as specified and directed.

One 3/5 pin socket outlet, 5 Amp on independent board complete all as specified and directed.

One 3/5 pin socket outlet, 5 Amp on same board complete all as specified and directed.

One bell /buzzer point controlled by one push button on independent board complete all as specified and directed.

M&L for point wiring with FRLS PVC insulated unsheathed multi-stranded copper conductor 2.5 Sq.mm (nominal area ) single core cable 1100 Volt grade drawn in and Including new rigid non metallic concealed PVC Conduit in wall, surface of ceiling with all fittings, such as tee, bend, elbow, socket etc including pressed steel sunken boxes (Terminal boxes) with earth dolly,duly galvanised, with white shade frame & cover plate of suitable module for modular switch / or sockets including FRLS PVC insulated unsheathed stranded copper conductor 2.5 Sq.mm (nominal area) single core cable as earth continuity conductor to common earth and connected to earth dolly, Including making good the disturbed portion of the wall complete all as specified and directed.

Dismantling / Taking down existing unserviceable sub main wiring from batten / conduit of any size all as directed. Removing the material from work site and making good the disturbed portion/ surface of wall/ floor/ ceiling etc by using cement mortar and colour/ white wash to match with the existing surface / location complete all as specified and directed.

M &L for sub main surface wiring with PVC insulated unsheathed copper conductor cable of size 6 Sqmm single core 1100 volt grade drawn in and Including new rigid non metallic concealed PVC conduit of suitable size (Not less than 25 mm dia) in wall and surface of ceiling including 6 Sqmm PVC insulated unsheathed copper conductor cable for continuous earthing form main earth dolly including making good the disturbed portion of wall complete all as specified and directed. Note :- Two run of 6 Sqmm copper cable one run of 6 Sqmm copper cable and PVC conduit will be measured as a single length

S&F Switch Modular type, 6 Amp, 240 Volts , one way complete all as specified and directed.

S&F Switch Modular type, 6 Amp, 240 Volts , Two way complete all as specified and directed.

S&F Switch Modular type, 16 Amp,240 Volts , one way complete all as specified and directed.

S&F Socket outlet, Modular type, 6 Amp complete all as specified and directed.

S&F Socket outlet, Modular type, 6&16 Amp complete all as specified and directed.

S&F Bell Push, Modular type, 6 Amp complete all as specified and directed.

S&F Fan regulator, modular type electronic step type complete all as specified and directed.

S&F ceiling rose surface bakelite two to three terminal 65x50 mm complete all as specified and directed.

S&F in replacement Tube light fittings LED type 1x20 Watt 4 ft long incl LED tube rod and incl 3 core flexible wire 0.75 Sqmm copper cable complete all as specified and directed.

S&F in replacement Tube light fittings LED type 1X10 Watt, 2 ft long incl LED tube rod and incl 3 core flexible wire 0.75 Sqmm copper cable complete all as specified and directed.

Supply & fix LED bulk head ,10 W complete all as specified and directed.

S&F Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed. .

S&F LED Bulb 9 watt 230 volt retrofit type complete all as specified and directed.

S&F in bell ding dong operating on AC 230 volt single phase complete all as specified and directed.

S&F MCB DB SPN 8 Way with acrylic double door complete all as specified and directed.

S&F including flushing in wall MCB distribution board vertical TPN 4 way 415 Volts AC double door type sheet steel phosphatised powder painted with bus bar neutral earth bar including provision of MCB TPN, FP 100 Amp conforming to IP 43 as incomer all as complete all as specified and directed.

S&F MCCB 4 pole 100 Amp 415 volt with breaking capacity of 16 KA complete all as specified and directed.

S&F MCB SPN 240V 40 Amps C series 10 KA complete all as specified and directed.

S&F MCB SP 240V 6 to 32 Amps C series 10 KA complete all as specified and directed.

Taking Down the KWH meter along with wooden board/DB after removing all electrical connection complete all as specified and directed.

M&L for Refixing & connecting the same KWH meter after complete repairs, wiring, elements& parts change as necessary or fixing new serviceable KWH energy meter for proper functioning complete all as specified and directed.

S&F Sheet metal enclosure factory made of size 20cm x 25cm x 12.5 cm deep box made out of 2mm thick MS sheet with double door with locking arrangement , epoxy power coated holes drilled for cable entries suitable for accommodating electric energy meter including brick/cement works as per site requirement including flushing the box in wall and making good the disturbed portion of wall /surface complete all as specified and directed.

Taking down old U/S LT UG cable of any size from trenches/ pipe/ floor/ walls complete all as specified and directed.

Supply laying jointing cable XLPE insulated PVC sheathed strip wire armoured 1100 volt 4 core 25 sqmm multi stranded aluminium conductor laid in trenches/wall/ducts etcincluding necessary fixing arrangement such as cable lugs glands etc complete after removing/taking out extg unsv cable complete all as specified and directed.

M&L for sand cushioning to under ground cables with a layer of sand 8 cm before laying the cable and 15 cm after laying the cable complete all as specified and directed. Note : only punned soil will be measured and paid.

Supplying & laying factory made unreinforced Pre cast concrete cable covers, class LV, type 1 flat of size 250 x 150 x 40mm laid in trenches as protection to cables complete all as specified and directed.

S&F HDPE pipe of size 50 mm dia complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick buried directly in ground (earth pit not less than 2 mtr deep below ground level with top edge of the plate not less than 1.4 mtr below normal ground level , connected earth wire 4 sqmm by means of bolts nuts check nuts and washers of galvanised iron or steel all as shown in electrical plate No 5 connected to earthing test point all as specified or indicated including PCC pit in PCC(1:3:6) type C-1 cast iron frame 50mm thick pre cast RCC(1: 1 1/2:3) nominal mix cover slab reinforced with 8 mm dia mild steel deformed bar 15cc and suitable handle of 10 mm Dia round bar including necessary excavation earth work in soft/loose soil and disposal of spoil to a distance n.exc 50m and funnel with watering pipe wire mesh copper lugs etc GI protection pipe of size 15 mm bore including testing complete all as specified and directed.

M&L for point wiring with FRLS PVC insulated unsheathed multi-stranded copper conductor 4.0 Sq.mm (nominal area ) single core cable 1100 Volt grade drawn in and including rigid non metallic concealed PVC Conduit on wall , surface of ceiling with all fittings, such as tee, bend, elbow, socket etc including pressed steel sunken boxes (Terminal boxes) with earth dolly,duly galvanised, with white shade frame & cover plate of suitable module for modular switch / or sockets including FRLS PVC insulated unsheathed stranded copper conductor 4.0 Sq.mm (nominal area ) single core cable as earth continuity conductor to common earth and connected to earth dolly, complete all as specified and directed. (For Geyser)

Supply & fix Exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230, 50 Hz, RPM 1200, copper winding of sweep 300 mm complete all as specified and directed.

Supply and fixing electrical Water heater storage type, steel body with copper inner tank of capacity 50 litre, BEE 5 star rated complete with all accessories such as safety valve, thermostat, NRV, connection piece etc, include complete fixing on wall and making connections complete all as specified and directed.

Supply and laying 16 sqmm 2 core cable XLPE/PVC insulated armoured and sheathed LT 1100 volts grade with aluminium conductor complete all as specified and directed.

ANANT ENTERPRISES (BID ID -3400602)

M/s MANN CONSTRUCTIONS (BID ID -3409378)