REPAIR/REPLACEMENT OF B/R WORKS/FITTINGS INCLUDING PAINTING OF MES INSTALLATION UNDER AGE B/R-I AND AGE B/R-II IN JORHAT MILITARY STATION UNDER GE JORHAT.

Amount

Dismantling of Asbestos cement (corrugated, semi corrugated etc) sheets in roof covering complete all as directed.

Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required complete all as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises complete all as directed.

Demolition of cement concrete in any description and any position complete all as directed.

Demolition of cement concrete (un reinforced) in ground floors and paving n. exc. 15 cm thickness (below or above ground level) complete all as directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) in any description and any position complete all as directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as directed.

Taking down cement plaster from brick or concrete surfaces of any description including racking out joints, hacking for key, scrubbing down with water etc complete all as directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) n. exc. 1.5 Sq. M each, complete all as directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) exc. 1.5 Sq. M but not exc. 4.0 Sq M each, complete all as directed.

Taking up or down, steel tubing 15 mm bore, and connection including cleaning for re-fixing or removal from site of work complete all as directed.

Taking up or down, steel tubing 20 mm bore, and connection including cleaning for re-fixing or removal from site of work complete all as directed.

M & L for cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth in brick walls complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets, complete all as directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground complete all as directed.

Dismantling fencing wire mesh, any type complete all as directed.

Excavating in post holes (or similar holes) each not exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance not exc 50m and making good surface, work in soft/loose soil complete all as specified and directed.

S & F galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured complete all as specified and directed.(Weight of barbed wire will checked by BOO as assemled by AO )

Dismantling of PVC pipe of any description complete all as specified and directed.

Supply only galvanized steel chain link fence fabric of mesh size 100 mm X 100 mm, made out of 2.50 mm nominal dia of mesh wire complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and directed.

M & L for PCC 1:3:6 Type C2 using 40mm graded aggregate in foundations, filling and mass concrete complete as specified and as directed.

M & L for RCC M-20 using 20mm graded aggregate in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete as specified and as directed.

M & L for PCC 1:3:6 Type C2 using 40 mm graded aggregate in surface channels and drains complete as specified and as directed.

M&L for PCC (1:3:6) type C-I with using 20 mm graded aggregate as in benching, kerbs copings, edging of drain etc including necessary form work wherever required all complete as specified and as directed.

M&L for PCC (1:2:4) type B-I with using 20 mm graded aggregate as in benching, kerbs copings, edging of drain etc including necessary form work wherever required all complete as specified and as directed.

Materials and Labour for, Digital/Printed Non - skid Ceramic tiles, coloured, 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm,conforming to IS 15622, Grade B II, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 15 mm thick screed bed or bedding layer of cement mortar (1:4),complete all as specified and directed.

Materials and Labour for, Digital Non - skid Ceramic tiles, coloured, 7 to 8 mm thick area of each tile exceeding .11 sqm but not exceeding 0.18 sqm,conforming to IS 15622, Grade B II, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 15 mm thick screed bed or bedding layer of cement mortar (1:4),complete all as specified and directed.

Materials and Labour for, Digital Non - skid Ceramic tiles, coloured, 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm,conforming to IS 15622, Grade B II, in riser of steps, skirting, dado and pillar laid over cement screed base with and including 15 thick rendering Cement mortar (1:3) complete all as specified and directed

Materials and Labour for, Digital glazed ceramic coloured tiles, 300 X 200 X 7mm thick, conforming to IS 15622, Grade B III, on vertical surface of wall such as dados, skirting etc, set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10 mm thick screed bed or bedding layer of cement mortar (1:4), complete all as specified and directed.

Materials and Labour for Granite (of any type) tiles 18-20mmthick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing, over and including 20 mm thick screed bed or bedding layer of cement mortar (1:6), complete all as specified and directed.

Materials and Labour for, Prepolished chemically treated chequered cement concrete tiles with grey cement and pigment,20cm x 20cm x 25mm thick,set, jointed and pointed in neat cement slurry in floors over and including 20 mm thick screed bed or bedding layer of cement mortar (1:4), complete all as specified and directed.

Materials and Labour for brick work with Sub Class ‘B’ bricks straight or curved on plan exceeding 6M mean radius built in cement mortar (1:6), complete all as specified and directed.

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips and including welding has to be done with minimum 20 cm over lap for new and old of any height. Complete all as specified and as directed.

S & F mild steel screw bolts (machine made), diameter of neck 11 to 15 mm with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exceeding 5 cm but not exceeding 10 cm long complete all as specified and as directed.

S & F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 complete all as specified and directed.

S & F hot rolled low tensile structural steel of grade E165 as per IS 15911: 2010 as in hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc. Wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar works complete all as specified and as directed.

Material and Labour for pre-painted, galvalume aluminium zinc coating GI based corrugated steel sheet, 0.50 mm thick of any colour, having tensile strength of 550 Mpa, as in roof covering/cladding to wall, fixed with self-tapping screws, complete all as specified and directed.Make(Tata bluescope/Sexena Marine Tech or equivalent make)

Material and Labour for pre-painted, galvalume aluminium zinc coating GI based plain steel sheet, 0.50 mm thick of any colour, having tensile strength of 550 Mpa, as in roof covering/cladding to wall, fixed with self-tapping screws, complete all as specified and directed.(Tata bluescope/Sexena Marine Tech or equivalent make)

Materials and Labour for mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290, Grade E-165 complete all as specified and directed.

S& F of steel window with side hung shutters incl. projecting/box type hinges double with steel handles steel peg stay complete with both mosquito proof and glazed shutter and 10 cm devetailed or welded including shop coat red oxide primer compete with and including taking down unserviceable one and making good disturbed surfaces as per existing specfication complete all as specified and as directed.

S & F hot rolled medium and high tensile structural steel of grade E165 as per IS 15911: 2010 as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles complete all as specified and as directed.

S & F 2nd class hardwood small fittings such as brackets of any type, latch and hinge blocks, shapped door and window stops and the like, including all necessary labours; articles n exc 200 cu. cm each complete as specified and directed.

S & F pressed steel frames of size 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc.complete as specified and directed.

S & F pressed steel frames of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc.complete as specified and directed.

Supply and Fix, Factory made 30 mm thick, flush shutters premium quality , solid core construction, with particle board core and plywood face panels,both faces is covered with decorative face veneer with lipping/frame to match, complete all as specified and directed.

S&F 2nd class Factory made hardwood Glazed and skeleton shutters 35 mm thick, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkat complete all as specified and directed

Supply and Fix, solid PVC door frame of size 50 mm X 47 mm made out of 5 mm Prelam PVC sheet reinforced with MS square tube, fixed in opening all as specified and directed.

Supply and Fix, factory made solid panel PVC door shutter 30 mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded prelam PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and prelam PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail and bottom rail: Panelling of both sides prelam PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, fixed to door frame complete all as specified and directed.

S & F 1.00mm thick steel rolling shutters without ball bearing of push pull or manual type as specified, including top cover, anchoring rod, hasp & staple and one shop coat of primer; erected in position as indicated

Supply and Fix,IS marked mild steel butt hinges, medium weight, cold rolled 100 mm size complete all as specified and directed

Supply and Fix,IS markedStainless steel butt hinges, medium weight, cold rolled 75 mm size complete all as specified and directed

S & F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy to door shutter complete all as specified and directed

Supply and fix Aluminium anodized barrel tower bolts of extruded section, 150 mm long complete all as specified and directed.

Supply and fix Aluminium anodized barrel tower bolts of extruded section, 200 mm long complete all as specified and directed.

S & F in repair 200mm long mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed complete all as specified and directed.

Supply and Fix, aluminium handles, Fabricated type, anodized, 150 mm size, complete all as specified and directed.

Supply and Fix, aluminium handles, Fabricated type, anodized, 125 mm size, complete all as specified and directed.

S & F in repair 150mm mild steel pressed handles, oval type, stove enamelled black complete all as specified and directed.

S & F in repair 300mm long mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

Supply and Fix,3 mm thick sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sq M in each pane complete all as specified and directed.

S & F of figured glass, pin head type 4mm thick in squares n.exc 0.50 Sqm in each pane complete all as specified and as directed.

Supply and Fix,3 mm thick sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sq M in each pane with and including hacking out old broken glass (any thickness, size, quality or description) from frame including providing wooden beads painted with two coat of enamel paint over a coat of primer complete all as specified and directed.

S & F in repair 300mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

Supply and Fix, stainless steel wire cloth, 0.36mm nominal dia. of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.

M&L providing and fixing of false ceiling with powder coated exposed GI grid suspension system (E-grid T-2420 or equivalent of Armstrong having load carrying capacity of 12.5 Kg/M3 with mid span deflection not exceeding 1/360 span with hanger spacing of 1200 mm c/c) consisting of Main Runner 3600 mm long, Cross Tee 1200/600 mm long and Wall Angle. The wall angle shall be fixed on PVC dash fasteners on the perimeter of the wall with steel screws with distance 300 mm c/c. The main runners to be placed @ 1200 mm, the cross tee 1200 mm will be inserted in the pre-cut slots of Main Runner at regular interval of 600 mm to form a modular grid of 1200x600mm. Additional cross tees of 600 mm shall be placed perpendicular to the Cross Tee 1200 mm long to finally form a grid of 600 mm x 600 mm with and including 6 mm thick HSPC (High pressure steam cured) oceanic pre primed, self embossed, textured designer board, water, termite & fire resistant for insulation and acoustic purpose to be placed in the grid system duly suspended with 4 mm dia GI bar hangers fixed with steel dash through fasteners from purlins with butterfly clips (wt 0.007 kg/clip), hold down clips (wt-0.0035 Kg/clip), with provn of light fixture complete all as per manufacturer instructions and as directed. Make Armstrong or equivalent make as mentioned in PS

Materials and Labour for waterproofing treatment to existing RCC roof in the following steps complete all as specified and directed. (i) Complete removal of the existing water proofing treatment. (ii) Wire brushing and cleaning top surface of tiles, lime terracing or cement concrete, including flashings and junction of parapets, etc., and surface painting, with a layer of blown grade bitumen of any penetration applied hot @ 1.7 kg per sq. m, blinded with grit or pea size gravel @ 0.006 cu.m per sq.m, and lightly tampered (area of flashings, etc., shall be added to the roof area) (iiii) Supply and Laying, chicken wire mesh of size 12.5 mm x 0.51 mm (24 SWG) hexagonal construction including all laps, cutting and waste in fabric reinforcement to PCC roof padding including providing 40 mm thick plain cement concrete (1:2:4) type B0using 12.5 mm graded aggregates as in roof padding. (iv) Providing 15 mm thick screed bed or bedding layer of cement mortar (1:3), mixed with liquid water proofing compound as per manufactures instructions, on concrete surface of roofs or terracing and finishing surface even and smooth without using extra cement. (iv) Waterproofing treatment over smooth finished surfaces after application of cold applied bituminous primer @ 0.30 Kg /Sq M,, providing and laying APP polymer, modified, non-woven polyester fabric of 150 grams/square metre, reinforced membrane, 3.00 mm thick, weighing 3.00 Kg / Sq M, with surface finish of white mineral, by torch on application method, with minimum 75 mm overlap on longitudinal direction and 100 mm overlap on the transverse direction and finally applying with one coat of bituminous based solar reflective aluminium paint @ 100 gms / Sq M complete all as specified and directed.

Materials and Labour for 75 mm thick plain cement concrete (1:3:6) type C2 using 40 mm graded aggregates as in plinth protection/floor including finishing surface even and smooth without using extra cement complete all as specified and directed.

Materials and Labour for 100 mm thick plain cement concrete (1:2:4) type B1 using 20 mm graded aggregates as in plinth protection/pavings/path including finishing surface even and smooth without using extra cement Spike rolling to surfaces or making impressions of expanded metal, whilst the concrete is green complete all as specified and directed.

M&L for cement concrete 40mm thick type B-1, 1:2:4 (20 mm graded aggregate) as in base of flooring, finished even and rough to receive the top layers all complete as specified and as directed

Materials and Labour for 50 mm thick plain cement concrete (1:2:4) type B1 using 20 mm graded aggregates as roof top including finishing surface even and smooth without using extra cement to ascertain the proper slope with WPC as per manufacturer instruction complete all as specified and directed.

Supply and Fix in repair PVC valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle, of capacity 10 Litres, including brackets, flush pipe, complete all as specified and directed.

Supply and fix in repair PVC connections 15 mm size with PTMT nuts of length 450 mm,complete all as specified and directed.

Supply and Fix, in repair bib tap, cast copper alloy, fancy type, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule,15 mm bore and fixed, complete all as specified and directed. Make:Cat No.CON-037KN of Jaquar or equivalent make of MARC/Kohler)

Supply and Fix, in repair stop valves/Angle cock, cast copper alloy, fancy type, chromium plated,screwed down, high pressure with crutch or butterfly handle, screwed both ends for steel pipe of for unions, 15 mm bore, complete all as specified and directed:Make:Cat No.CON-053KN of Jaquar or equivalent make of MARC/Kohler)

Supply and Fix,in repair stop valves, cast copper alloy , fancy type, chromium plated, screwed down, high pressure with long shank and cup (concealed type), screwed both ends for steel pipe of for unions, 15 mm bore, complete all as specified and directed.Make:Cat No.CON-083KN of Jaquar or equivalent make of MARC/Kohler)

Supply and Fix, in repair pillar taps, cast copper alloy, with capstan heads, fancy type, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe, 15 mm bore, including taking down existing unserviceable one complete all as specified and directed.Make:Cat No.CON-011KN of Jaquar or equivalent make of Marc/Kohler)

Materials and Labour for galvanized steel tubing, medium grade, 15 mm bore with all fittings and fixed complete to walls and ceiling or laid in floor, complete all as specified and directed.

Materials and Labour for galvanized steel tubing, medium grade, 20 mm bore with all fittings and fixed complete to walls and ceiling or laid in floor, complete all as specified and directed.

Supply and Fix, in repair brass chromium plated shower rose 125mm size,with swivel joints, fixed to steel pipe or union 15 mm bore with and including 225mm long arm, complete all as specified and directed.

Supply and Fix, in repair 20 mm dia. Stainless steel conduit ,wall thickness 1.00 mm, overall PVC coated including suitable fixing brackets and fancy type end caps as in darpary rod for doors/ windows, complete all as specified and directed.

S&F vitreous china squating pan orissa pattern size 580x440 mm white with integral foot rest complete including lime concrete (excl flushing cistern and flush pipe )but connecting to flushing pipe , anti symphonage pipe etc with and including cement concrete bedding and demolition of existing one complete all as specified.

S&F in repair vitreous china wash hand basin 550x400mm (flat back type) including cutting for and pinning in ends of brackets with and including 32mm CP waste coupling fittings, , and waste water pipe complite all as specified and as directed.

Supply and Fix in repairs, grating square 150mm size of PTMT with grating square fitting of size 150mm made in two part for smell and mosquito proofing with minimum 25mm water seal of PTMT (Minimum weight 85gms), complete all as specified and directed.

Supply and Fix, PVC (SWR) floor trap, plain with grating including jointing with solvent cement with dia. of out let 75 mm, complete all as specified and directed.

Supply and Fix, 75 mm bore UPVC (SWR) pipes, single socketed in any length with rubber ring joints,laid in trenches or in floors/wall, complete all as specified and directed.

Supply and Fix, 110 mm bore PVC (SWR) bends any radius, with access door, complete all as specified and directed.

Supply and Fix, 75 mm bore PVC (SWR) bends any radius, with access door, complete all as specified and directed.

S & F 100mm bore `spun pipes` cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and directed

S & F 75mm bore `spun pipes` cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and directed

S & F 100mm bore `spun pipes` cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, fixed to walls complete all as specified and directed

S & F 75mm bore `spun pipes` cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, fixed to walls complete all as specified and directed

S & F of 75mm bore bends (any radius), diminishing pieces or tapers complete all as specified and directed

S & F of 100mm bore bends (any radius), diminishing pieces or tapers complete all as specified and directed

S & F of 75mm bore bends (any radius),with oval access door diminishing pieces or tapers complete all as specified and directed

S & F of 100mm bore bends (any radius),with oval access door diminishing pieces or tapers complete all as specified and directed

S & F of 75mm bore branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed

S & F of 100mm bore branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed

S & F 100mm cast iron sanitary connections short connections pipe of length upto 300mm complete all as specified and directed

S & F 100mm cast iron sanitary connection socket to fit WC out-let complete all as specified and directed

S & F of 100mm bore traps `P` or `S` complete all as specified and directed

M&L for preparation of new or previously undecorated wooden surface of any description, not otherwise described over 10 cm width or girth and applying two coats of Synthetic enamel paint over one coat of pink primer complete all as specified and as directed.

M & L for applying two coats of synthetic enamel paint (of colour as approved by GE) on external surfaces of pressure filter with pipe lines, sluice valves including thoroughly cleaning, preparation of surfaces complete all as specified and as directed. (Approximate minimum area : 30 sqm)

Material and Labour for applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer on new steel and iron surface exceeding 10 cm in width or girth including preparation of surfaces complete all as specified and directed.

M & L for treating small articles such as stop, covers, gully gratings, holdfasts, ends of posts, backs of chowkats etc., area n exc 0.1 sq. m each complete all as specified and as directed.

M & L for applying two coats of synthetic enamel paint on external surfaces of gravity filter and two coats of black bituminous paint to internal surfaces upto top level of filter media complete including thoroughly cleaning & preparation of surfaces complete all as specified and as directed. (Approximate minimum external area : 30.00 sqm & internal area : 15.0 Sqm).

M & L two coats of black bituminous paint to internal surfaces of steel clear water sump including thoroughly cleaning & preparation of surfaces complete all as specified and as directed.

M & L for applying two coats of synthetic enamel paint on external surfaces of steel clear water sump including thoroughly cleaning & preparation of surfaces complete all as specified and as directed.

M & L for applying two coats of synthetic enamel paint on external surfaces of steel sedimentation tank, Aeration Tower including thoroughly cleaning & preparation of surfaces complete all as specified and as directed.

M & L two coats of black bituminous paint on internal surfaces of steel sedimentation tank, Aeration Tower including thoroughly cleaning & preparation of surfaces complete all as specified and as directed.

M & L for applying one coat of weather coat exterior paint one as under coat and one as finishing coat to external surfaces of RCC sedimentation tank & Aeration Tower including thoroughly cleaning & preparation of surfaces complete all as directed within interval of 5 month. Approximately Minimum area : 200 Sqm

M & L for preparation of old painted steel surfaces and applying one coat of aluminium paint externally on overhead pressed steel tank including thoroughly cleaning & preparation of surfaces complete all as specified and as directed.

M & L for preparation of old painted steel surfaces and applying one coat of black bituminous paint internally on overhead PS including thoroughly cleaning & preparation of surfaces complete all as specified and as directed.

M & L for preparation of old painted steel surfaces and applying one coat of synthetic enamel paint on steel stagging of overhead pressed steel tank including thoroughly cleaning & preparation of surfaces complete all as specified and as directed.

M & L for preparation of old painted steel surfaces not exceeding 10 cm width or girth when unconnected with other painting or when painted in different tint and applying one coat of synthetic enamel paint on steel stagging of overhead pressed steel tank including thoroughly cleaning & preparation of surfaces complete all as specified and as directed.

M & L for applying two coats of synthetic enamel paint over a coat of red oxide primer after preparation of surfaces on pipe lines any type/size on surface / floors with in the pump house / installation premises for sizes upto & including 250 mm bore complete all as specified and directed. (Note: Painting includes painting on fittings without considering any additional factors. Area of fittings shall be calculated as per nominal size of pipe and length.)

M & L for applying one coat of weather coat exterior paint to external surfaces of RCC OH tank on 15 metre staging including preparation of surfaces and necessary scalfolding complete all as specified and as directed.

M & L for applying two coats of synthetic enamel paint over a coat of red oxide primer after preparation of surfaces on pipe lines of RCC OH tank on 15 metre staging complete all as specified and as directed. (Note: Painting includes painting on fittings without considering any additional factors. Area of fittings shall be calculated as per nominal size of pipe and length.)

M&L for rendering 5mm thick plaster in cement mortar 1: 3 on fair faces of concrete surfaces such as soffit of slab, beam, ceiling etc including finishing the surface even & smooth complete all as specified and directed

Materials and Labour for rendering 15 mm thick, cement plaster, in cement mortar (1:6) on surface fair face of brickwork in walls and finishing surface even and smooth without using extra cement, complete all as specified and directed.

Materials and Labour for rendering 5 mm thick, cement plaster, in cement mortar (1:4) mixed with water proofing compound as per manufactures instructions over and including 10mm thick backing coat in cement mortar (1:4) on fair faces of brick work or concrete surface in walls, complete all as specified and directed. Note: - (Water proofing compound will be measured and paid separately)

Supply only Liquid water proofing compound conforming to IS: 2645 - 1975 specification complete all as specified and as directed (Make : CICO No- 1/SIKA/ACCO PROOF).

M&L for preparation of old distempered surfaces of walls including cornices, pilasters and other wall features etc by washing, rubbing down and stopping and applying one coat acrylic distemper on old surfaces complete all as specified and as directed Make;Berger (Bison)/J&N(Jensolin)/Asain Piants(Tractor)/Nerolac(Beauty)

M&L for preparation of new plastered or un -plastered from walls, and applying two coats acrylic distemper on walls, over and including a coat of 1 mm thick white wall care putty complete all as specified and as directed.Make;Berger (Bison)/J&N(Jensolin)/Asain Piants(Tractor)/Nerolac(Beauty)

M&L for complete removal of existing treatment from walls, and applying two coats acrylic distemper on walls, over and including a coat of 1 mm thick white wall care putty complete all as specified and as directed.Make;Berger (Bison)/J&N(Jensolin)/Asain Piants(Tractor)/Nerolac(Beauty)

M&L for preparation of new or previously untreated surfaces of wall and applying three coats of white wash complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces on ceiling and applying three coats of white wash complete all as specified and directed.

M&L for preparing old decorated plastered or unplastered surfaces of wall including cornices, pilasters and other wall features etc by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots etc and applying one coat of white washing on the wall all as specified and directed

M&L for preparing old decorated plastered or unplastered surfaces of wall including cornices, pilasters and other wall features etc by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots etc and applying one coat of cement base paint on the wall all as specified and directed

Material and Labour for applying two coats of cement-based paint, white or tinted to new plastered surfaces on walls including priming with alkali resistant priming paint and including preparation of surfaces complete all as specified and directed.

M&L for preparing old decorated plastered or unplastered surfaces of wall including cornices, pilasters and other wall features etc by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots etc and applying one coat of white washing on the ceiling all as specified and directed

Material and Labour for complete removal of existing treatment by means mechnical process / Machine as directed by manfucaturer through authorised applicator of manufacturer,s and applying two coat of100 % Acrylic Exterior Emulsion paint (Berger,Weather coat Advanced XP Brand/Asain Paints :Apex ultima Brand /ICI:Dulux Weather shield Max Brand/J&N:Safeguard Optima Brand painting over and including a coat of primer to old plastered or unplastered surfaces on walls including preparation of surfaces, complete all as specified and directed.Note (Work shall be exectuted through authorised applicator and shall be got approved by before commencement of work)

Material and Labour for preperation of new or previously untreated surfaces and applying two coat of100 % Acrylic Exterior Emulsion paint (Berger,Weather coat Advanced XP Brand/Asain Paints :Apex ultima Brand /ICI:Dulux Weather shield Max Brand/J&N:Safeguard Optima Brand painting over and including a coat of primer to old plastered or unplastered surfaces on walls including preparation of surfaces, complete all as specified and directed.Note (Work shall be exectuted through authorised applicator and shall be got approved by GE before commencement of work)

A M CHOUDHURY AND CO

AJOY DUTTA CHOWDHURY AND CO

M/S AK SINGH