8743/GWL/E8 SPECIAL REPAIR TO BLDG No P-187 AND PROVN OF COVERED SHED INCL CERTAIN MINOR WORKS IN THE AREA OF AGE B/R-II UNDER GE GWALIOR

Amount

Surface Excavtion n.exc 30 cm deep avg.15cm in Hard /dense type soil and getting out complete all as specified and directed.

Rolling and consolidating formation surfaces in cutting with power roller of capacity exc 8 tonne and n.exc 12 tonne.

M&L moorum /red bajri filling in floors or paving laid in layers n exc 15cm thick spread leveled and rammed including watering complete all as specified and directed by Engineer in charge.

M&L Soiling (or subbase ),150 mm thick (spread thickness ) with crushed or broken lime /sand stone of grading 63 to 90 mm boulders or quarried stone ,interstices filled ,surface formed and rollled and consoildated to requried gradient and camber with 8 to 12 tonne power roller complete all as specified & directed .

M&L for 150 mm thick (compacted thickness) WBM in two layers of each one layer 75mm thick (compacted thickness) with coarse stone aggregate (lime /sand stone) of grading 1 (40 to 63 mm size spread & rolled with 8 to 12 tonne power roller, rolled and consolidated to required gradient and camber all as specified.

M&L PCC Type D2 (1:4:8) using 40mm graded stone agg as in foundation filling mass concrete complete.

M&L for PCC 100 mm thick (1:2:4) type B-2, (using 40 mm graded stone aggregate) as in floor, finished even and rough complete all as specified and directed.

M&L for forming constrution joint 30 mm deep X 10 mm wide filled with sealing compound of Grade 'B'.

M&L for forming contraction (dummy ) joint 65 mm deep X 10 mm wide filled with sealing compound of Grade 'B'.

S&F Pre painted galvalum sheet 0.50 mm thick having aluminum zinc coating 150 gsm/ sqm steel sheet any colour having tensile strength of 550 Mpa as in Roof covering /cladding to wall fixed with self tapping screws complete all as directed

Removing excavated soil to a distance not exc 500 m depositing where directed at a level n.exc 1.5m above the starting point.

Excavating in posts holes (or similar holes) in hard/dense soil each n.exc 0.50 cu.m getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25cm watering, and removing surplus soil to a distance n.exc 50m and making good surface.

S&F Steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates conforming ti I.S. 1161-1979 grade St.-240 complete all as specified and directed

M&L Hand rails, half round or other stock section or core for wooden hand rail straight portion , drilled and counter sunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing post including cutting tops to shape as directed, drilling holes, notching for wire , etc.; flat iron fillets ( for securing wire mesh etc. including all necessary drilling , bolting or rivetting , etc., and similar work conforming to Fe 290 Gde E 165 with and including applying two coats of synthetic enamel paint over a coat of primer alround before fixing in position complete all as specified and directed

M&L for preperation of new surface two coat of synthetic enamel paint over coat of Red oxide primer over new surfaces nexc 10 cm width or girth complete all as specified

M&L for applying for two coats of synthetic enamel paint over a coat of red oxide primer on new steel surfaces over 10 cm width or girth including preparation of new surfaces complete all as specified

Excavating in trenches in any type of soil , n exc 1.5 m wide and n. exc. 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soil complete all as specified and as directed.

S&F Mild steel TMT bars 6 to 8mm dia as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed

S&F mild steel bars 10 mm dia and over (TMT) cut to length bent to shape required including cracking,bending spirally for hooping ends and binding with and including mild steel wire not less than 0.90 mm dia quality of steel conforming to Fe-410-0 or Fe-410-S all as specified and directed

M&L Reinforced cement concrete ( nominal mix)Type B1 (1:2:4) ( 20 mm graded aggregate) as in foundation , raft, footing,Wall, plinth beam, base for column etc complete all as specified and directed specified and directed

M&L Formwork to side of rough finished surfaces of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work , vertical or to batter etc all as specified and directed

M&L Brick work with old size sub class 'B' Bricks straight or curved on plan exc 6m mean radius with CM (1:4) all as specified and directed.

M&L15mm Rendering with CM (1:4) over brick/concrete could surface fair & even surface complete all as specified and as directed.

M&L Renedering 5 mm thick on fair faces of brick work or concrete surfaces in cement mortar (1:3) finished even and smooth without using extra cement.as in walls complete all as specified and as directed.

M&L Three coat of W/W over new prepared wall surfacess complete all as specified and as directed.

M & L for Powder coated (minimum thickness of powder coating 50 micron) aluminium frame for doors , windows , ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

M & L for Powder coated (minimum thickness of powder coating 50 micron) aluminium door shutters of aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, rubber neoprene packing, powder coated aluminium handles 150mm size 2 Nos, 3 Nos powder coated aluminium hinges heavy duty and 02 Nos 150mm long powder coated aluminium tower bolts in each door shutter with powder coated aluminum snap beading, screws etc. complete all as specified and directed Note : Panel filling ie. glass, fibre sheet, board etc. shall be measure and paid for separately.

M & L for Powder coated (minimum thickness of powder coating 50 micron) aluminium window and ventilator (adequate track of openable / sliding) without sash, aluminium section weighing 0.55 kg/m including joining cleats, glazing clips, rubber neoprene packing, necessary powder coated hardware ie. handles, barrel tower bolts, hinges etc, powder coated aluminum snap beading, screws etc. complete all as specified and directed Note : Panel filling ie. glass, fibre sheet, board, wire mesh etc. shall be measured and paid for separately.

S&F for 12 mm thick prelaminated particle board exterior grade prelamilated one side with decorative choice lamination and other side balancing white lamination fixed with screws complete all as specified or as approved by GE .

S&F galvanised wire cloth, 0.48mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised staples complete all as specified and directed

S & F for door closer hydraulically regulated, designation No. 3, universal type, aluminium die-cast body (ISI Marked), suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed in repair complete all as specified and directed

S & F of double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed in repair complete all as specified and directed

Taking down chowkhat or frame (without taking off shutter from the frame) not exceeding 1.5 Square Metre each , removing from the site Cutting holes exc 150 Sq.cm but n.exc 400 Sq.cm in super facia area into or through brick walls built in mud mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required complete all as specified and as directed.

Taking down chowkhat or frame (without taking off shutter from the frame) exceeding 1.5 sqm and not exc 4.00 sqm each , removing from the site Cutting holes exc 150 Sq.cm but n.exc 400 Sq.cm in super facia area into or through brick walls built in mud mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required complete all as specified and as directed.

Taking down shutter of any description exc 1.0 sqm but nexc 2.00 sqm each complete all as specified and as directed.

S&F pressed steel frame 125mmx60mm for doors with one or more rebates including necessary fixing lungs and hinges, lock strike plate,etc complete all as specified and directed

S&F solid PVC door frame of size 50mm×47 mm made out of 5 mm pre laminated colour PVC sheet reinforced with MS square tube supplying and fixing in opening as per specifications and drawings.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top and bottom rails M.S frame shall be covered with heat moulded pre lam colour PVC 'C' channel having a PVC shut strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail& bottom rail, panelling of pre lamanited colour PVC sheet to be fitted in MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement.

Cutting holes in brick/stone wall ,depth of embedment portion of hold fast exc half brick wall but not exc one brick wall, built in cement mortar or cement lime mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B1 as required complete all as specified and directed

M & L for 35 mm thick glazed and skeleton factory made shutters of 2nd class Hard Wood, open rebated and prepare to reveive glass, guage etc (without sash bars ) edges of framing plain chamfered or rounded, fitted with moulded beads both sides for securing glass etc, size of members of shutters as specified complete all as specified and directed.

M & L for factory made 35 mm 2nd class Hard Wood, plain framed factory made panelled shutters ( two panel) with lock rail and panel of 9mm B.W.P. commercial ply or 12mm veneered particle board medium density, wood particle board with commercial veneering on both face IS 1003 ( Part-I) kiln seasoned and chemically pressured treated complete all as specified and directed.

S&F for framed work such as grills gratings, etc, with ends of bars shouldered and or riveted , or forged into spikes, framed guard bars , barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe 290 Gde E-165, , complete all as specified and directed.

M&L for applying two coat of synthetic enamel paint over one coat primer including Preparation of new wooden surface any description not otherwise described over 10 cm width or girth and complete all as specified and directed.

S&F 100 mm long size 2mm thick stainless steel hinges medium weight complete all as specified and directed by Engr-in-Charge.

S&F 150 mm long aluminium anodised , barrel tower bolt of extruded section and fixed complete all as specified and directed.

S&F aluminum handles cast type, anodized of 150 mm size complete all as specified and directed.

S&F butt hinges 100mm long medium weight, cold rolled mild steel.

S&F Mild Steel, sliding door bolt 250mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

M&L for PCC 1:3:6 ( 12.50mm graded aggregate) type C0 for filling in pressed steel frames and like complete all as specified and directed

Taking down cement plaster of any description and in any position of brick/concrete surfaces on walls/celing etc. including racking out joints, hacking for key, scrubbing down with water etc & prepared to receive new plaster complete all as specified and directed.

M&L for rendering 5 mm thick in Cement Mortar (1:4) on ceiling finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10 mm thick in CM (1:6) on brick work or conrete surfaces/stone masonary and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for 10 mm thick rendering in cement mortar( 1:4) on brick or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

Supply only integral water proofing compound (ISI marked) complete all as specified and as directed.

M&L for applying two coat of oil bound emulsion paint on walls including preparation of new plastered surface comlete all as speified and directed.

Material and labour for preparation of new plastered surfaces of wall, chhajjasetc and applying two coat of water proof water based emulsion paint ( Acrylic paint exterior grade) complete all as specifed and directed.

M&L for preparation of the newly plastered surfaces of ceiling & applying 3 coats of white wash on ceiling surfaces complete all as specified and directed.

Preparation of old decorated surface by brooming down or steel wire brushing to remove all loose scales, and foreign materials scarping down , smoke soot moulds , moss and efflorescent salts treating oil and greasy spots on old plastered or unplastered surfaces of wall including cornices, pilasters etc applying one coat of white wash , complete all as specified and directed.

Preparation of old decorated surface by brooming down or steel wire brushing to remove all loose scales, and foreign materials scarping down , smoke soot moulds , moss and efflorescent salts treating oil and greasy spots on old plastered or unplastered surfaces of ceiling including cornices, pilasters etc applying one coat of white wash , complete all as specified and directed.

M&L complete removal of existiong treatment (internal and external) on walls by scrapping with steel wire brushing, scraping down smoke soot/ plants roof from wall/chhajjas comlete all as specified and directed.

M&L , preparation of wall surface and aplying wall putty minimum 1mm thick on wall surface finished even and smooth including rubbing complete all as spefied and directed

Material and labour for preparation of old plastered surfaces of wall, chhajjasetc and applying two coat of water proof water based emulsion paint ( Acrylic paint exterior grade) complete all as specifed and directed.

M&L for applying two coat of oil bound emulsion paint white or tinted on walls including preparation of old plastered or un plastered surface comlete all as speified and directed.

S & F in repair Curtain rail Stainless Steel decorative type 25 mm dia including fixing bracket and end knob complete specified and diected by engineer in charge.

S&F End Knob 25mm dia stainless steel for curtain rod complete all as secified and directed

Demolition of cement concrete of any description and in any position (unreinforced) in ground floors and paving not exceeding 15 cm thick (below or above GL) complete all as specified and directed.

M&L 10mm thick rendring with CM (1:3) over wall/floor surface even and smooth mixed with WPC complere.

M&L Providing two coats of water proofing coating of tepecrete of cico , pidicrete of pidilite complete all as specified and directed.by Engineer in charge.

M&L plain cement concrete (1:5:10) tye D-2 ( using 40mm graded stone aggregate) as in foundation/ mass concrete complete all as specified and directed.

Taking down existing tarfelt froom roof and removing from site all as specified

M&L for 10 mm thick rendering in CM (1:4) over roof ,surface finished even and rough mixed with water proofing compond complete all as speceified and as directed by engineer- in charge . Note : Water proofing compound shall be measured and paid separately under appropriate item of BOQ as "supply only "

M &L For applying water proofing treatment with the following coats :- (a) First coat of bitumen primer conforming to IS -3384 @ 0.4 Kg/sqm (b) Second Layer of APP based polymectric membrane minimum weighing 3kg /sqm and minimum 3 mm thick reinforced with polyster non woven fabric (wt. not less than 150 gms /sqm ) land on primed surface by torch application complete all as specified and as directed by engineer in charge.

Dismantiling of stone slabs and tiles (Kota stone etc.) of any discription or any thickness in floors, aprons, skirting, dado pcc tiles at roof etc. laid bedded and pointed in any mortar complete all as specified and directed.

M&L Granite slab 16 to 18 mm thick machine cut, bedded and joined with grey cement slurry and pointed with white cement with admixture of pigment to match over and including 15 mm thick screed bed CM (1:6) .the shade of granite stone including cutting and polishing type as in cill and jamb/skirting, steps cooking plateforms includigng rounding off the exposed edges all as specified and directed.

M&L for machine cut Kota stone slab 20 mm to 25 mm thick , as in flooring , laid over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing , over and including screed bed or bedding layer of mortar 15 mm thick in cement mortar (1:6 ) complete all as specified and directed.

M&L for machine cut kota stone slab 20mm -25 mm thick as in riser / steps, skirting, dado and pillars laid and jointed with grey cement slurry mixed with pigment to match with the shade of the slab including rubbing and polishing over and including 10 mm thick backing coat in CM (1:4) complete all as specified and directed.

Roughning surface of old concrete floor by picking, swiping cleaning and washing down with water to remove dust etc. complete all as specified and directed.

M&L for vitrified ,coloured and printed tiles of 8 to 10 mm thick (Square / Rectangular ) polished area of each tiles not exceeding 0.36 Sqm as in flooring over and including 15 mm thick cement screed in (1:4 ) CM set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles complete all as specified and directed.

M&L for vitrified ,coloured and printed tiles of width as directed and 8 to 9 mm thick as in skirting fixed over and including 10 mm thick cement screed in (1:4 ) CM set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles complete all as specified and directed.

Dismantling floor, hearth or wall tiling of any description and in any position including cement mortar bedding (but not backing) complete all as specified and directed.

M&L non skid ceramic Coloured tiles, 300mmx300mmx7mm thick, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match with the colour of tiles, over and including 15 mm thick screed bed or bedding layer of cement mortar 1:6 complete all as specified and directed.

M&L for digital glazed ceramic tiles, coloured tiles 300mm x 450mm x 7mm thick on vertical faces ie. as in skirting/dado etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles fix over and including 10 mm thick backing coat in cement mortar (1:4) complete all as specified and directed.

M&L for PCC (1:2:4) type B0, (using12.5 mm graded stone aggregate), as in foundations / mass concrete/ levelling course complete all as specified. .

Demolition of brick work /stone work built in cement mortar including all quoins, arches, pillars etc complete all as specified and as directed.

M& L for Brick work with sub-class `B' bricks, straight or curved on plan to any radius, in half brick work built in cement mortar 1:4 complete all as specified and as directed.

M&L for 75mm thick PCC (1:2:4) Type C2 using 40mm graded stone agg as in plinth protection surface even and fair without using extra cement including forming & filling expension joints 65 mm deep x 10 mm wide filled with sealing compound grade A complete all as specified and as directed

Taking up or down steel tubing and connetion including cleaning for refixing or removing to store of 20mm bore of pipe.

Taking up or down steel tubing and connection including cleaning for refixing or removing to store of 25mm bore of pipe.

Supply and laying 20 mm dia .of bore CPVC pipe SDR11 and Plain CPVC SDR11 fittings (ISI ) marked ,concealed or fixed to wall ,ceiling or laid in floors complete all as specified and as directed by engineer in charge .

Supply and laying 25 mm dia .of bore CPVC pipe SDR11 and Plain CPVC SDR11 fittings (ISI ) marked ,concealed or fixed to wall ,ceiling or laid in floors complete all as specified and as directed by engineer in charge .

Supply and laying 40 mm dia .of bore UPVC pipe Plain UPVC fittings (ISI ) marked ,concealed or fixed to wall ,ceiling or laid in floors complete all as specified and as directed by engineer in charge .

S&F in repairs 110mm dia PVC(SWR)pipes single socketed, in any length with rubber ring joints,fixed to walls.

S&F 75 in repairs mm dia PVC(SWR)pipes single socketed, in any length with rubber ring joints,fixed in Wall/laid in floor complete all as specified and as directed.

S&F 110mm dia PVC(SWR)pipes bends any radious with acces door complete.

S&F 75 mm dia PVC(SWR)pipes bends any radious.with acces door complete complete all as specified and as directed.

S&F 110mm dia PVC(SWR)pipes junction,single (single T/Y ) equal or unequal any radious.with acces door complete complete all as specified and as directed.

S&F 75mm dia PVC(SWR)pipes junction,single (single T/Y ) equal or unequal any radious.with acces door complete.

S&F 110mm dia PVC(SWR) vent cowl complete all as specified and as directed.

S&F 75 mm dia PVC(SWR)pipes bends any radious complete all as specified and as directed.

S&F 110mm dia PVC(SWR)pipes bends any radious complete all as specified and as directed.

M & L 75 mm dia of out let PVC (SWR) floor trap plain with cp grating incl. jointing with solvent cement as in repair complete all as specified and as directed.

M & L PVC (SWR) gully trap 125 /100 plain with grating incl. jointing with solvent cement as in repair complete all as specified and as directed.

S&F for in repair PVC valveless syphonic action type flushing cistern low level white with inlet ball valve,float end handle handle including bracket complete of capacity 10 litres, complete all as specified and directed.

S&F for in repairs 15mm angle cock ISI Mark chromium plated,cast copper alloy, with brass ceramic disc spindle and capston heads,scewed down high pressure, with or without lettered 'hot' or Cold' with long srewed shanks and flynuts, srewed for iron pipe fixed and complete all as specified.

S&F in repairs for wall mixer with Two in one pattern in of brass CP, complete all as specified and directed.

S&F for in repairs Heatth Faucet with one meter PVC flexible body pipe of CP including fixing bracket, complete all as specified and directed.

S&F for shower rose brass chromium plated without swivel joints, 100 mm in size including fixing to steel pipe complete all as specified and directed fixed in repairs, complete all as specified and directed.

S&F for as in repair viterous china wash down water closet pan (pedestal pattern) white excluding fixing bolts,flushing cistern and flush pipe including connection to drain and to flushing pipe syphonage pipe etc and mild steel chromium plated or aluminised hinges device & on CP Jet complete all as specified and directed.

S&F for in repairs of vitreous china wash basin, white, Oval type ,Including waste coupling ,waste pipe and labour for fixing pillar tap ,pvc connection but including cutting for and pinning in ends of and including brackets size as approved by GE complete all as specified and directed. Note : Pillar tap and PVC connection will be measured paid separetly.

S&F for in repairs Brass CP WHB mixer for mixing hot & cold water screwed down for 15mm bore iron pipe complete all as specified.

Supply only 15mm dia PVC connection with PTMT nuts of length 450 mm, complete all as specified and directed.

S&F for in repair CP tubular towel rail D type 20mm dia and 60cm long complete all as specified and directed.

S&F for peg set of six S.S. fixed to wall with PVC plugs and screw, complete all as specified and directed.

Dismantling water tanks of any description and in any position , of capacity exceeding 250 litres but not exceeding 500 litres complete all as specified and directed.

S&F Rotational moulded poly-ethylene Three layered water storage tanks (cylinderical vertical with thread top laid) 1000 litres capacity, white colour hoisted and fixed in position complete all as specified and directed.

S & F 20mm ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 20 m m - 210 gms / 25mm-455gms/ 40mm - 690 gms)

S & F in repair gun metal globe / gate value with iron wheel head screwed both ends for iron pipe of 20mm bore all as specified.

S&F plastic water closet seat covered white coloured closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging devise complete all as specified and directed.

M&L for machine cut cudapah slab 30mm to 35mm thik, as in plate form laid over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and including screed bed or bedding layer of mortar 15mm thick in cement mortrar (1:6) complete all as specified and directed.

Material and labour for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & attern as in footh path, parks, lawns, drive ways or light traffic arking etc of required strength, thickness & size/shape made by table vibrating method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/laying of interlocking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra cement complete all as specified and directed.

M&L for (factory made machine pressed) cement concrete ( 1:2:4) type B-1 (20mm graded agrregate) in lintels upto 1.5m clear span, cills, stes, seimic and other similar bands, plinth course, string course, lacing cours, arapets and railings upto 60cm in height, coping, kneelers, apex stones, bed plates, kerbs, water througs and the like including wheathering slightly rounded or chamfered angle and throating complete all as specified and directed.

Dismantling boarding any description fixed with nails in any position (including cup board shutter/shelve upto 25mm thick) complete.

S&F for 18 mm thick PVC Celuka ply of both side prelaminated and other side plain white colour fixed with screws ,solvent cement /adehesive complete all as specified .

S&F for aluminium anodised barrel tower bolts of extruded section of 100mm size, complete all as specified and directed.

S&F for continuous (piano) hinges mild steel bright finish or electro galvanised width of width of flaps nexc 30 mm (when open), complete all as specified and directed.

S&F for extruded aluminium alloy handle of 100 mm size fabricated type, anodised.complete all as specified .

S&F for Haps and staple safety type Aluminium anodised with MS hinge pin including bolt to hinge pin of 100 mm size sixed with screw complete all as specified .

S&F for magnate catcher of metal body and striking plate heavy duty includind fixed with screw, complete all as specified and directed.

S&F for PVC bath room cabinate mirror of Size 500mmx400 mm make Prayag Cat No 556 complete all as specified and directed.by Engineer in charge.

S&F for in repairs Soap dish of CP fixed with pvc rawal plugs and screw, complete all as specified and directed.

Dismantling Trellis work (Jafri), including taking as under of battens in trellis (posts and rails measured separately) complete all as directed .

M & L Providing precast cement concrete louvres and jallies, 25mm thick (measured solid) Type B0 (1:2:4 12.5mm graded aggregate set in CM 1:6, including all mould- ings but excluding frame complete all as directed .

M&L Providing precast cement concrete Type C1 (1:3:6 20 mm graded aggregate) in win- dow or door cills, ntels,bressumers, steps, quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone wallin). corbels, brackets, etc. (of any section indicated), with plain fair faces, including chamfers, Watherings, throat- ing etc. and setting in mortar complete with joints to match

Dismantling of wrought iron or mild steel work of any description not other wise provided for complete all as specified and as directed.

Dismantling of timber in fillets, rails, posts, rafters, purlins etc under 40 Sq. cm provided for complete all as specified and as directed.

S&F rolled section as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates confirming to Fe-290 ( Gde E-165) complete all as specified and directed

Dismantling of AC (corrugated / semi-corrugated) sheets in roof covering including any type of ridges complete all as specified and as directed.

&F corner glass shelf 300mm ( with ABS Bracket) comlete all as specified and directed.

Taking down carefully existing aluminum / copper point wiring (light, fan, socket or power point) complete of any description including fitting such as switches, ceiling roses, pendants, tube light fitting, ceiling fan with regulators, sockets, wooden boards, laminated sheets from sunken boxes, boards, shades light fitting etc and making good the disturbed surfaces of walls, floors, ceiling etc to match with existing surfaces complete all as specified and directed.

Taking down submain wiring of any size any type and in any position metalic/non metallic PVC conduit of wooden batten complete all as specified and directed.

Taking down unserviceable Sheet metal box & MCB DB SPN with MCB's of any make/capacity, complete, all as specified and directed by Engr-In-Charge.

Taking down unserviceable TPN DB with MCB's of any make/capacity, complete, all as specified and directed by Engr-In-Charge.

M&L, concealed point wiring with PVC insulated and unsheathed electric cable 1100 volts grade single core FRLSH confirming to IS 694:2010 having multi stranded copper conductor of 1.5 Sqmm nominal cross sectional area (ISI marked with valid CML No) drawn in and including concealed non metallic rigid PVC conduit medium grade( ISI marked with valid CML No) not less than 20 mm dia confirming to IS 14930 (Part-I) 2001, with all fitting and fixing accessories and 1.5 Sqmm FRLSH PVC insulated unsheathed multistranded copper conductor cable as continuous earth conductor, connected to common earth dolly by providing suitable lugs with & including pressed steel modular sunken terminal boxes factory made for mounting modular switch, sockets regulators etc on modular frame plates & cover, duly painted with two coats of anti corrosive paint/black bituminous paint outside and two coats of aluminium paint inside complete:-

One light point controlled by one switch.

One Ceiling fan point controlled by one switch.

One Exhaust fan point controlled by one switch.

One Bell/Buzzer point controlled by one way 5 Amp push button switch.

One 5 pin multipurpose socket out let 5/6 Amps on the same board with other switch.

One 3 pin/5 pin switch socket outlet, 5 Amps on independent board.

One light point controlled by 2- two way switch

All as per item No. 146 but point wiring with 2.5 sqmm FRLSH confirming to IS 694:2010, multistrand copper conductor cable for one six pin socket outlet 15 Amps controlled by one switch on independent board and 2.5 sqmm FRLSH PVC insulated multi strand copper conductor cable as continous earth wire.

S&F Modular white cover plate with frame 3 module complete all as specified and directed.

S&F Modular white cover plate with frame 4 module complete all as specified and directed.

S&F Modular white cover plate with frame 8 to 12 module complete all as specified and directed.

S&F Modular switch single pole one way 6 Amp complete all as specified and directed.

S&F Modular switch single pole Two way 6 Amp complete all as specified and directed.

S&F Modular socket out let, multipurpose, 2 in 1 5 pin, 6 Amp of 2 module complete all as specified and directed.

S&F Modular switch piano, flush button single pole one way 16 Amp complete all as specified and directed.

S&F modular socket out let multipurpose flush type, 2 in 1 6 Pin 6/16 amps of 2 module complete all as specified and directed.

S&F Modular bell push 6 Amps complete all as specified and directed.

S&F of buzzer Ding Dong, AC, 230 Volts, single pole complete all as specified and directed.

S&F ceiling rose surface bakelite 63.5 mm dia three terminal complete all as specified and directed.

S&F modular electronic step rotary type fan regulator of two module capacity 80 to 100 Watt, 240 volts, AC 50Hz complete all as specified and directed.

S&F Lamp holder with metal ring, PVC/Polycarbonate type with back plate suitable for batten fittings non ISI Marked complete.

S&F LED Lamp 09/10 watt complete.

S&F LED 'T' Type Mirror light fitting 09/10 watt with provision of fixed in Lamp holder complete.

S&F Decorative ultra slim LED Tubelight fitting of LED with extruded polycarbonate, enviormental friendly energy efficient ready to use, 20 watt, 6500K, 50000 burning hours fitting, incluing reqd length of not less than 1.0 Sqmm PVC multistranded BIS marked 03/02 core copper conductor for electrical connection from ceiling rose to connector of LED fitting including testing on completion all as specified and directed.

S & F security light fittings better optics for uniform distribution IP 65 protection LED of 30 watt, 6500 K, 50000 Burning hours, Heat resistance glass, pressure die cast aluminium housing including 25mm dia galvanised iron pipe light grade bracket bent to shape over all length 0.60mtr fixed to wall with 02 Nos FI clamps made of 40 x 5 mm FI, 15 cm long, 8 mm dia bolts and nuts with washers grouted in wall complete including reqd length of 1.5 Sqmm PVC multistranded BIS marked, 03 core copper conductor for connection from ceiling rose to light fittings incl testing on completion all as specified and directed.

Supply & fix BEE 5 star rating energy efficient ceiling fans 1200 mm sweep with minimum air delivery 210 cum/min, down rod all accessories required including regd length of 3 core 1.0 sqmm PVC multistranded copper conductor, PVC connector for proper hanging of fan and testing complete all as specified and directed.

Supply & fix Fresh air ventilation fans 300 mm sweep with all fixing accessories required including making hole & regd length of 3 core 1.0 sqmm PVC multistranded copper conductor, and testing complete all as specified and directed.

Supply and fix Water heater storage type, electric,capacity 25 litres.BEE 5 star rated complete.

S&F Sheet metal enclosures single pole and neutral with a two pin and earth plug and socket with and including one single pole MCB 20 amps, 240 volts, 10 KA complete all as specified and directed.

M&L, sub main wiring with two single core PVC insulated unsheathed FRLSH confirming to IS 694:2010, multi stranded copper conductor (ISI marked with valid CML No), cable 1100 Volt grade, 6 sqmm size drawn in and including non metallic rigid PVC concealed conduit medium grade (ISI marked with valid CML No) not less than 25 mm dia confirming to IS 14930 (Part-I) 2001, with all fitting & fixing accessories including one run single core PVC insulated unsheathed 6 Sqmm FRLSH copper conductor (ISI marked with valid CML No) colour code as a earth continuity and connected upto DB complete all as specified and directed. (NOTE: (i) Two run of single core PVC cable with one run of earth conductor and conduit shall be measured as one unit and the quoted rates shall be deemed to be inclusive for cutting chases in wall/pillars/columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface with putty to match with the existing surface.

M&L, sub main wiring with two single core PVC insulated unsheathed FRLSH confirming to IS 694:2010, multi stranded copper conductor (ISI marked with valid CML No), cable 1100 Volt grade, 4 sqmm size drawn in and including non metallic rigid PVC conduit (ISI marked with valid CML No) not less than 20 mm dia confirming, with all fitting & fixing accessories including PVC insulated unsheathed 2.5 Sqmm FRLSH copper conductor (ISI marked with valid CML No) as connected to earth with dolly completed all as specified and directed (cutting of wall and making good disturbed surface of wall shall be measured and aid saprately)

S&F sheet metal enclosure double door distribution board factory made for MCB DB load link VTPN 4 way suitable for MCCB as incomer, 125 Amp,4 pole & Including MCCB 125 amps 4 pole 25 KA complete. (when MCB's are to be used) with suitable size of busbar complete,fixed flush in wall including chases wall for fixing DB and making good the distributed wall surfaces to match with existing specification including taking down all as directed by Engr-in-Charge at site.

Supply and installed hi wall split units indoor/ outdoor unit complete with cordless remote control unit and with inbuilt air ioniser and plasma filler for better indoor air quality with minimum 4 Star rating and EER 302 of capacity 2 Ton

S&F voltage stabilizer for automatic oeration, single phase naturally air cooled indoor type & designed for input variation vetween 170 V to 250 V with output voltage stabilizer 230V with accuracy of 2.5% and of capacity 5 KVA comlete all as specified and directed.

S&F sheet metal earth plug, socket, single pole and neutral with single pole MCB 20 Amps 240 volts in repairs complete all as specified and directed.

S&F MCB DB, sheet metal enclosures double door SPN 8 way with bus bar 240 volts 2 in 1 shutter type (METAL DOOR) type with blanking plates where required and IP 43 degree protection complete all as specified and directed.

S&F MCB DB, sheet metal enclosures double door SPN 4 way with bus bar 240 volts 2 in 1 shutter type (METAL DOOR) type with blanking plates where required and IP 43 degree protection complete all as specified and directed.

S&F, MCB SPN 63 Amps, 240 volts 'C' series 16 KA ,including connection with suitable size copper lugs complete all as specified and directed.

S&F, MCB SP 63 Amps, 240 volts 'C' series 16 KA ,including connection with suitable size copper lugs complete all as specified and directed.

S&F, MCB SP 240 volts, 6 to 40 Amps, 'C' series 10 KA including connection with suitable size copper lugs. complete all as specified and directed.

Supply and fixing in replacement PVC flat insulated aluminium conductor service wire 2 core 10 Sqmm complete all as directed.

Supplying, laying, testing and commissioning of XLPE insulated screened PVC bedded galvanised steel strip or wire armured electric power cable (Heavy duty ) with aluminium conductor 1100 volts grade, cross sectional area 35 Sqmm 3.5 Core.

Supplying, laying, testing and commissioning of XLPE insulated screened PVC bedded galvanised steel strip or wire armured electric power cable (Heavy duty ) with aluminium conductor 1100 volts grade, cross sectional area 10 Sqmm 4 Core.

Returning, filling of excavated soil, including spreading leveling, watering and well ramming in layers, not exceeding 25cm complete all as specified and directed.

Sand filling in trenches with clean dry unwashed sand free from sharp particles, gently punning around the cables complete.

Bricks, old size sub class `B' laid in trenches with width wise along the alignment of the cable as protection complete.

S&F tube 'Light' grade galvanised Pipe of 50 mm dia with all fitting for cable protection, laid in trenches, fixed to wall and floor by MS shaddle & fixed with pole, 02 position by MS clamp made of 40x5 mm MS flat, complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) vertically, with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 of MES Schedule Part-I connecting to earthing test. Testing on completion with and including necessary excavation and earth work in any type soil, earth lead connected to earth test point & to main switch board etc with & including adequate quantity of charcoal dust and common salt, test point, PCC (1:3:6) type C-1 (using 20mm graded BT stone aggregate) for earth pit with 40 x 40 x 6mm mild steel angle iron frame for cover, internal surface of concrete shall be given 10mm thick plaster in CM 1:4, pre cast RCC (1:2:4) type B-1 (using 20mm graded BT stone aggregate) 40mm thick cover, reinforced with 8mm dia deformed or TMT bars 3 Nos both way with 12 mm dia round bar handle, GI medium grade watering pipe 20 mm dia with funnel and wire mesh and 15mm dia GI medium grade earth lead protection pipe including provn of earth test point made of 50 x 5 mm MS Flat in 'D' shape 500 mm legth grouted in wall complete 01 x 6 mm multistrand PVC insulated copper conductor ( Green Colour) to be provided from test point to DB through 20 mm dia concealed non metallic conduit complete all as specified and directed.

S&F tube Medium' grade galvanised with all fitting laid in trenches, of 50 mm dia complete all as specified and directed.

S&F tube Medium' grade galvanised with all fitting laid in trenches, of 25 mm dia complete all as specified and directed.

S&F tube Medium' grade galvanised with all fitting fixed to wall/floor, of 20 mm dia complete all as specified and directed.

S&F gun metal gate valves with iron wheel head screwed at both ends for iron pipes of 50 mm dia complete all as directed.

S&F gun metal gate valves with iron wheel head screwed at both ends for iron pipes of 20 mm dia complete all as directed.

M&L for Construction of valve chambers of size 1.5x1.5 x1.2 internal dimentions with 150 mm thick PCC foundation 1:4:8 type D2 using 40 mm graded trap stone aggregate, 230 mm thick brick masonary wall with sub class 'B' bricks builts in cement mortar 1:4 10 mm thick plastering to brick masonary in cement mortar internally and externally upto 15 cm below ground level, 50 mm thick coping with PCC 1:2:4 type B1 using 20 mm graded crushed trap stone aggregate valve chamber having coller frame size 1.5x1.5 x1.2 made of mild steel angles of size 50mm x 50mm x 6mm and cover made of 2.5 mm thick mild steel sheet framed by 40x40x5 mm MS angle having 02 nos cross 'X' supprt fixed with coller frame by mild steel hinges - 02 Nos, locking arrangements with provision of locks and painting the steel surfaces with two coats of alluminium enameled paint over a coat of zinc chromate primer including neccessary earth work, excavation, all as specified and directed by Engineer-in-Charge .

Cutting of existing Cast iron pipes in position for insertion of new tees, for branch connection of 50 mm dia from 100 mm bore of pipe existing CI pipe.

Excavation over area n.exc 1.5m deep and getting out soft loose soil complete all as specified and directed.

BHAGIRATH CONSTRUCTION COMPANY

M/S MAHAVIR SINGH

Babatia super works

M/s Ratan Lal Jain and Co.

Vee kay construction