Remolding of Augmentation of Dhar Guwalu Karwal in GP Karwal Guwalu Tehsil Salooni District Chamba HP

Amount

Excavation in foundation trenches etc. in earth work in all kind of soil such as pick work,jumper work, blasting work in hard & soft rock and chiesaling work including slushy soil & under flooring water up to all excavated soil up to any lead & lifts from the edge of excavation and then depth and stacking the returning the stacked soil in 15 CM ( fifteen centimetres) layer's when required in to plinth sides of foundation etc. Consolidation each diposited layer by ramming & watering & then disposing of all surplus excavated earth as directed with in all lead of 20 meters in Chiselling /wedging out of rock complete in all respect in trench weir, sump well, anchor blocks, presedimentation tank steel bridge, check dam, site development works etc.within all leads and lifts as per the direction of Engineer-in-Charges.

Providing and laying cement concrete 1:3:6 ( One cement : three sand: six graded stone aggregate 40mm nominal size) and curing complete excluding the cost of form work form work in foundation and plinth within all leads and lifts as per the direction of Engineer-in-Charges.

Providing and laying cement concrete 1 : 1. 5 : 3 ( One cement : one & half sand: three graded stone aggregate 20mm nominal size) and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in:-

Foundation ,footing bases of column and the like mass concrete within all leads and lifts as per direction of Engineer-in-Charges.

In walls ( any thickness but not less than 0.10 metre thickness) attached pillasters, buttresses plinth and string cources etc. from top of foundationlevel up to floor two level within all leads and lifts as per the direction of Engineer-in-Charges.

Lintle beam, girder brassumers and cantilevers upto any floor two level etc. with in all leads and lifts as per the direction and entire satisfaction of Engineer-in-Charge.

In ARCHES upto floor two level within all leads and lifts as per the direction and entire satisfaction of Engineer-in-Charge.

Providing form work with steel plates 3.15 milimetre thick welding with angle iron in frame 30x30x5 milimetre so as to give fair finish including centering, shuttering and propping etc. with wooden battens and ballies, height of propping and centring below floor to ceiling not exceeding four metres and removal of the same for in-situ-reinforced concrete and plain concrete work in:-

Flat surface such as soffits of suspended floors, roofs, landing and the like floor etc. up to 200 milimetres in thickness including all leads and lifts as per the direction of Engineer -in- Charge.

Vertical surfaces such as walls (any thickness) partitions and the like including attached pillasters, buttresses, plinth and string courses and the like within all leads and lifts as per the direction of Engineer-in Charge.

Beam cantilevers girders and lintles side and soffits of beams, beam haunching, cantilevers, bressumersand lintles not exceeding one metre in depth in all height within all leads and lifts as per the direction of Engineer-in Charge.

Providing form work of ordinary timber plankings so as to give a rough finish including centering , shuttering, struand proping etc. height of proping and centering below supporting floor to ceilling not exceeding four metre and removal of the same for insitureindorced concrete and plain concrete work in Arches upto 6.00mtr. span within all leads and lifts as per the direction of Engineer-in-charg.

Providing tor steel reinforcement for reinforced concrete work including bending, binding and placing in position complete up to floor two level including within all leads and lifts as per direction of Engineer -in- Charge.

P/L cement concrete work 1:2:4(1cement:2sand:4graded stone aggregate 20mm nominal size)and curing complet excluding the cost of form work and reinforcemnet work, as per the direction and entire satisfaction of Engineer-in-Charge.

P/L cement concrete work 1:2:4(1cement:2sand:4graded stone aggregate 20mm nominal size)and curing complet excluding the cost of form work and reinforcemnet work,in suspended floor,roofs,landing and shelves and their support Balconies,Beams,girders,bressumers and contilevers upto floor two level as per the direction and entire satisfaction of Engineer-in-Charge.

Laying and jointing testing in trenches galvanised mild steel tubes or of approved make by JSV (HP) (list attached) screwed and socketed. ISI marked conforming to IS: 1239( latest with upto date ammendments) including tube fittings such as bends, tees, air valves, unions and collars etc as per direction and to the entire satisfaction of the engineer in charge (earth work in trenches to be measured and paid for separately).

15 mm dia nominal bore (LG)

20 mm dia nominal bore (LG)

25 mm dia nominal bore (LG)

32 mm dia nominal bore (LG)

40 mm dia nominal bore (LG)

50 mm dia nominal bore (LG)

65 mm dia nominal bore (LG)

Providing & Fixing of brass Wheel valve with hand wheel as per IS 780 Class upto 300mm dia (including brass spindle and as per IS 2906 class-II for idametre more than 300mm complete with bolts, nuts, rubber issertion etc.within all leads & lifts.

15 mm dia nominal bore

20 mm dia nominal bore

25 mm dia nominal bore

32 mm dia nominal bore

40 mm dia nominal bore

50 mm dia nominal bore

65 mm dia nominal bore

Providing & placing in horizontal layers Filtering media duly graded screened washed and cleaned as specified by the Engineer-in-charge.

Top Layer: Fine sand screened, cleaned, washed and graded effective size 0.2 to 0.4mm with uniformity cofficient 2.0 to 3.0 from approved source.

Second Layer : Coursed sand screened, cleaned, washed and graded effective size 3mm to 6mm from approved source.

Third Layer:- Bajri screened, cleaned, washed and graded effective size 6mm to 20mm from approved source.

Forth Layer:- Bajri (Coursed) screened, cleaned, washed and graded effective size 20mm to 25mm from approved source.

Bottem Layer:- Broken stone screened, cleaned, washed and graded effective size 50mm to 75mm from approved source.

Bricks in layer under bottom layer of filter media.

Providing and fixing C. I. manhole cover internal and frame conforming to IS 12592(PART-I) 1998 with latest amendments 560mm dia Medium duty 58Kg. within all leads and lifts as per the direction of Engineer-in-Charges.

Providing and fixing stair case (4.0 metre long & 0.35 metre wide) of angle iron fam 4.0 metre long of size 65x65x6mm embedded in cement concrete within all leads and lifts as per the direcrtion of Engineer-in-charge.

Steel work welded in built -up section, trusses and framed work including cutting housting fixing in position and applying a primering coat of red lead paint in grating, framed gaurd bar, ladders, railing, brackets and similer work within all leads and lifts as per the direction of Engineer-in-charge.

Providing and fixing of M.S. mosquito proofing ventilators 300mmX300mmX300mm complete in all within all leads and lifts as per the direcrtion of Engineer-in-charge.

RAKESH KUMAR

Ajay Kumar

P C Construction