Special repair to LT Network system and Provn of lights in certain different locations under GE (Utilities) Udhampur

Amount

Taking down the old/vintage LT feeder pillar box from the circuit system and supply & fix new LT feeder pillar box of following nomenclature as illustrated below:- Type:- System integrator Switchgear/Channel Partner. Switch gear Make:- L&T/ABB/Schneider/ Simens/Havells Panel sheet thichness:- 3.15mm CRCA Voltage:-415V, 3 Phase, 50Hz BUSBAR:- Copper (Tinned) shall be 1.5 times of incomer MCCB. Type:- Outdoor Panel. Base:- Angle iron 50x50x6mm. Accessories:- Indication lamps (R,Y,B), CTs(Required incomer size), Voltmeter,Ammeter,Cable glands wherever required. Wiring:- Wiring shall be 2.5sqmm for acc. (copper) Size of Panel:- Size as per switchgear accomodation , double door system ,hinges to be provided,powder coated to complete panel. Foundation:- PCC foundation, M-15, type C-1 according to panel including PCC coping, M-15. Glands : Incomer - 120 Sqmm, Outgoing : 95sq.mm - 1run and 50sqmm- 04 nos

Incoming (a) MCCB 160 A, 4 pole, with thermal magnetic adjustable and fixed magnetic setting with extended 50Hz ,415 V with rupturing capacity 25/26 KA-01 No. Make :- L&T/ABB/Schneider/Simens/Havells Outgoing (a) MCCB 125 A, 4 pole with thermal magnetic adjustable and fixed magnetic setting with extended 50 Hz, 415 V with rupturing capacity 35 KA-01 No. (b) MCCB 4 pole , Ics=100%Icu-25/26 KA, 415 Volts, 63 Amps , with thermal magnetic adjustable and fixed magnetic setting with extended terminals -04Nos. Make :- L&T/ABB/Schneider/Simens/Havells

All as per serial item No-01 here-in above but of following capacity :- Incoming (a) MCCB 160 A, 4 pole, with thermal magnetic adjustable and fixed magnetic setting with extended 50Hz ,415 V with rupturing capacity 35 KA-01 No, Make :- L&T/ABB/Schneider/Simens/Havells (b) Bus bar electrolytic grade copper and supported on Non-hygroscopic, non carbonising, corrosion resistance SMC insulators 250 Amp,4 pole, not less than 75 cm long mounted on insulators-01 set. Outgoing ( a) MCCB 4 pole ,Ics=100%Icu- 10 KA, 415 Volts, 40 Amps , with thermal magnetic adjustable and fixed magnetic setting with extended terminals -04 No Make :- L&T/ABB/Schneider/Simens/Havells

All as per serial item No-01 here-in above but of following capacity :- Incoming (a) MCCB 160 A, 4 pole, with thermal magnetic adjustable and fixed magnetic setting with extended 50Hz ,415 V with rupturing capacity 35 KA-01 No, Make :- L&T/ABB/Schneider/Simens/Havells (b) Bus bar electrolytic grade copper and supported on Non-hygroscopic, non carbonising, corrosion resistance SMC insulators 250 Amp,4 pole, not less than 75 cm long mounted on insulators-01 set. Outgoing ( a) MCCB125 A, 4 pole ,Ics=100%Icu- 25 KA, 415 Volts, with thermal magnetic adjustable and fixed magnetic setting with extended terminals -02 No. Make :- L&T/ABB/Schneider/Simens/Havells ( b) MCCB 63 Amp, 4 pole ,Ics=100%Icu- 25 KA, 415 Volts, with thermal magnetic adjustable and fixed magnetic setting with extended terminals -01 No Make :- L&T/ABB/Schneider/Simens/Havells

All as per serial item No-01 here-in above but of following capacity :- Incoming:- ( a) On load Change over switch 100 A, 4 pole ,Ics=100%Icu- 25 KA, 415 Volts, with thermal magnetic adjustable and fixed magnetic setting with extended terminals -01 No Make:- L&T,Legrand, Scheineiders, Havells, C&S Outgoing :- (b) Bus bar electrolytic grade copper and supported on Non-hygroscopic, non carbonising, corrosion resistance SMC insulators 250 Amp,4 pole - 01 set.

All as per serial item No-01 here-in above but of following capacity :- Incoming:- ( a) MCCB100 Amps, 4 pole ,Ics=100%Icu- 25 KA, 415 Volts, with thermal magnetic adjustable and fixed magnetic setting with extended terminals -01 No Make:- L&T,Legrand, Schneider, Havells (b) Bus bar electrolytic grade Aluminium and supported on Non-hygroscopic, non carbonising, corrosion resistance SMC insulators 200 Amp,4 pole - 01 set. Outgoing :- (a) MCCB 40 amps, 4 pole ,Ics=100%Icu- 10 KA, 415 Volts, with thermal magnetic adjustable and fixed magnetic setting with extended terminals -03 No Make:- L&T,Legrand, Schneider, Havells

All as per serial item No-01 here-in above but of following capacity :- Incoming:- ( a) On load Change over switch 100 A, 4 pole ,Ics=100%Icu- 25 KA, 415 Volts, with thermal magnetic adjustable and fixed magnetic setting with extended terminals -01 No Make:- L&T,Legrand, Schneider, Havells, C&S Outgoing :- (b) Bus bar electrolytic grade Al and supported on Non-hygroscopic, non carbonising, corrosion resistance SMC insulators 200 Amp,4 pole - 01 set.

All as per serial item No-01 here-in above but of following capacity :- Incoming:- ( a) MCCB 100 A, 4 pole ,Ics=100%Icu- 25/26 KA, 415 Volts, with thermal magnetic adjustable and fixed magnetic setting with extended terminals -01 No Make:- L&T,Legrand, Schneider, Havells, C&S Outgoing :- (b) Bus bar electrolytic grade Al and supported on Non-hygroscopic, non carbonising, corrosion resistance SMC insulators 200 Amp,4 pole - 01 set.

MCCB 4 pole, Ics=100%Icu- 35/36 KA, 415 Volts, 200 Amps , with thermal magnetic adjustable and fixed magnetic setting with extended terminals (in replacement) complete all as specified and directed by Engr-in-Charge. Make:- L&T/ABB/C&S/ HPL/ Schneider/ Simens/Havells

MCCB, 4 pole, Ics=100%Icu- 35/36 KA, 415 Volts, 160 Amps , with thermal magnetic adjustable and fixed magnetic setting with extended terminals (in replacement) complete all as specified and directed by Engr-in-Charge. Make:- L&T/ABB/C&S/ HPL/ Schneider/Simens/Havells

MCCB, 4 pole, Ics=100%Icu- 35/36 KA, 415 Volts, 315/320 Amps ,with thermal magnetic adjustable and fixed magnetic setting with extended terminals (in replacement) complete all as specified and directed by Engr-in-Charge. Make:- L&T/ABB/C&S/ HPL/ Schneider/Simens/Havells

MCCB, 4 pole, Ics=100%Icu- 25/26 KA, 415 Volts, 100 Amps, with thermal adjustable and fixed magnetic setting with extended terminals(in replacement) complete all as specified and directed by Engr-in-Charge. Make:- L&T/ABB/C&S/ HPL/ Schneider/Simens/Havells

LED Street light 60 watt made up pressure diecast aluminium housing with toughned glass and high power LEDs and secondary lens Dusk and down(sensor) with IP 66 protection system of efficasy >110 LPW including 10 KV SPD including taking down old UNSV Street lights complete all as specified and directed by Engr-in-Charge. Make CG/Philips/ Wipro/ HPL/ C&S/ Polycab Note : Contractor shall provide SPD -01 No and driver - 01 No of same configuration as per fittings provided. Rate quoted shall be deemed to be inclusive.

40mm GI pipe (light grade) bracket for holding the lights, single swan neck shape suitable to fix on top of tubular pole with clamps, nuts, bolts and washers complete all as specified and directed by Engr-in-Charge.

Steel tubular swaged poles erected to truly vertical or planted as strut complete with 6 mm thick mild steel base plate, welded to Pole, B-118 finial taper cap, bolts, nuts and screws, poles made out of ERW MS tubing conforming to IS-2713 Part-II type 410-SP-31 (9m long) including drilling of holes of required size for fixing of cross arms, painting the exposed surfaces of pole with two coats of aluminum paint over a coat of red oxide zinc chrome primer and with two coats of black bituminous paint on the end portion embedded in concrete, making five black and white bands at lower portion of pole above ground level/coping each 300 mm wide alternately and marking pole number with black paint at suitable height complete all as specified and directed by Engineer-in-Charge. Note:- The cost of earthwork, PCC foundation, steel clamps, MS Cross arms & bracing of angle iron etc shall deemed to be included in the quoted rate for this item.

Steel tubular swaged poles erected to truly vertical or planted as strut complete with 6 mm thick mild steel base plate, welded to Pole, B-118 finial taper cap, bolts, nuts and screws, poles made out of ERW MS tubing conforming to IS-2713 Part-II type 410-SP-64 (12 m long) including drilling of holes of required size for fixing of cross arms, painting the exposed surfaces of pole with two coats of aluminum paint over a coat of red oxide zinc chrome primer and with two coats of black bituminous paint on the end portion embedded in concrete, making five black and white bands at lower portion of pole above ground level/coping each 300 mm wide alternately and marking pole number with black paint at suitable height including The earthwork, PCC foundation,deemed to be coated rate by contractor complete all as specified and directed by Engineer-in-Charge. Note:- The cost of earthwork, PCC foundation, steel clamps, MS Cross arms & bracing of angle iron etc shall deemed to be included in the quoted rate for this item.

Thermoplastic, polystyrene unbreakable junction box of size 260 x 210 x 116 mm suitable for pole mounted outdoor type IP 65 insulated complete with F.I. clamp & nut, bolts, washers and including phase seperator between R, Y, B terminals and one MCB SP 6 amp 10 KA, all duly mounted on din cannel, cable glands for cable entry complete all as specified and directed by Engr-in-Charge. Make : Hensel Cat Part No K9350/ Hansu /Sintex

LED flood light with lens,150 watt, made uppressure diecast aluminium housing with toughned glass and high power LEDs and secondary lens with IP 66 protection system of efficasy >110/125 LPW including 10 KV SPD including taking down the old UNSV Street lights complete all as specified and directed by Engr-in-Charge. Make CG/Philips/ Wipro/ HPL/ C&S/ Polycab Note : Contractor shall provide SPD -01 No and driver - 01 No of same configuration as per fittings provided. Rate quated shall be deemed to be inclusive.

LED bollard lights of 10/11 watt capacity, IP-65 rated inverted pyramid tripod type with soft 360 degree lights distribution complete all as specified and directed by Engr-in-Charge. Make : Philips/Wipro/Polycab Note : Necessary Grouting for fixing of bollard must be included in the quoted rated by the contractor.

Angle iron , supports, clamps and back plates, fabricated from structural steel section including bolts, nuts, washers, welding, bending (cold or hot) drilling holes for bolts any shape or size as indicated or directed and inclusive painting with one primer coat of zinc chromate and two coats of aluminium paints complete all as specified and directed by Engineer-in-Charge.

Automatic street light control switch of 8 KW (in replacement) three phase using Infrared sensor based Nature Switch for automatic switching of street light. Nature switch operation should be based on Natural Light Lux*level. Reqd illuminance level also have part night operation facility for min 4 hrs to max 12 hrs. The sensor along with suitabe rating power contractor (s), one Incoming and three Outgoing MCBs rating of 20-32 Amps & main load circuit wiring (copper) of min 10 sqmm should be enclosed in a pole/wall mountable rust proof, electric shock proof, termite proof and FR grade thermoplastic polycarbonate enclosure conforming to IP66 protection class-2. The circuit should be also have provision for manual operation (i.e. sensor by pass option) complete all as specified and directed by Engr-in-Charge. Make : Indoasian/ L&T/ Havells

Supply, laying and fixing on poles or passing through pipes or laid under floor or through walls etc (in replacement) jointing and testing LT Cross Linked Polythene Insulated (XLPE insulated) galvanized steel strip armoured electric cable 1100 volt grade, heavy duty ISI marked with aluminium conductor and overall served with an outer sheath of PVC, of cross sectional area 185 Sqmm 3.5 Core including taking out old unserviceable LT cables complete all as specified and directed by Engr-in-Charge:- Note : Excavation, earthwork, Pipe for cable protection to be measured and paid for separately. Make: Havells/Polycab/KEI/Gloster/ Garandlay/Univarsal.

All as per Item No. 21.00 here-in-before but of size120 sqmm 3.5 core.

All as per Item No. 21.00 here-in-before but of size 70 Sqmm 3.5 core.

All as per Item No. 21.00 here-in-before but of size 50 Sqmm 3.5 core.

All as per Item No. 21.00 here-in-before but of size 35 Sqmm 3.5 core.

All as per Item No. 21.00 here-in-before but of size 25 Sqmm 3.5 core.

All as per Item No. 21.00 here-in-before but of size16 Sqmm 4 core.

Galvanised steel tubing, light grade, 80 mm dia (ISI marked) for protection of under ground cable on poles / walls under road crossing etc including dismantling & taking down existing unserviceable pipe complete all as specified and directed by Engr-in-Charge.

Road cutting/ boring of existing road/path for laying of GI pipe protection for UG cable including making good distrurbed area/surface complete all as specified and directed by Engr-in-Charge.

Earthing with GI earth plate electrode 600 X 600 X 6mm buried directly in ground (earth pit not less than 2.25M deep below ground level ) with top edge of the earth plate not less than 1.5M below ground level connected to GI strip 25 x 4 mm thick for earthing lead fixed by means of nuts,bolt,washers etc connected to earth test point complete all as specified in electrical plate NO 3 of SSR1996 part 1 ,including necessary excavation and earth work in any strata of soil,comman salt, charcoal dust, 40 mm dia light grade GI pipe for protection to earth lead, GI water pipe 20mm dia with funnel &wire mesh , PCC pit with CI cover and frame etc complete all as specified and directed by Engr-in-charge. Note:- All the joints shall be made with welding to get proper conductivity.Note: On testing after completion of earthing, if desired earth resistance is not obtained, the earthing will be re-done by the contractor at his own risk & cost to the entire satisfaction of Engineer-in-charge

Double walled corrugated (DWC) pipe of size 120 mm including snap fit coupler conforming to IS14930 (Pt-II)/IS16205 Pt-II for protection of HT/LT cable in under ground complete all as spd and directed by Engr-in-Charge.

Double walled corrugated (DWC) pipe of size77mm including snap fit coupler conforming to IS14930 (Pt-II)/IS16205 Pt-II for protection of HT/LT cable in under ground complete all as specified and directed by Engr-in-Charge.

Double walled corrugated (DWC) pipe of size 40 x 32 mm conforming to IS: 14930/IS 16205 for protection of LT cables including necessary snap-fit coupler required for fixing complete all as specified and directed by Engr-in-Charge.

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth for laying of underground cable and getting out in soft/loose soil complete all as specified and directed by Engr-in-Charge.

All as per serial item No 26 here-in-above but depth exceeding 1.5 metre.

Returning, filling in, excavated soil in trenches including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick complete all as specified and directed by Engr-in-Charge.

Removing of excavated soil to a distance not exceeding 50 mtr and deposited where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed by Engr-in-Charge.

LT UG cable XLPE insulated, armoured heavy duty electric cable with aluminium conductor 1100 Volts grade of cross sectional area 10 Sqmm 2 core complete all as specified and directed by Engr-in-Charge.

Modular Box made of FRP/impact resistance plastic & heat resistance including Bus Bar 50 Amps 1 Phase and 1 Neutral connector terminal complete all as specified and directed by Engr-in-Charge.

vijay kumar gupta and co

proach associates

MOHAN LAL AND SONS

FANGALIA TRADERS

kailu construction co

D P ASSOCIATES

slathia construction works

LUXMI ELECTRONIC WORKS