Repair/Maintenance of 0.4 MLD STP and allied works at Mil Stn Kapurthala under GE Kapurthala.

Amount

Excavation in trenches in soft/loose soil not exceeding 1.50 mtr wide and not exceeding 1.50 mtr in depth for taking out and laying CI/GI pipe complete all as specified and directed by Engr-in-Charge.

Returing, filling in, including spreading, leveling watering and well ramming inlayers not exceeding 25 cms thick each layer complete all as specified and directed by Engr-in-Charge.

Removal of surplus spoil to a distance not exceeding 50 mtr away and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed by Engr-in-Charge.

M&L for sand cushioning to under ground cable with a layer of sand 8 cm thick before laying of cable and 15 cm thick after laying of cable complete all as specified and directed by Engr-in-Charge.

M&L for brick protection using old size sub class ‘B’ bricks, laid flat, dry adjacent to each other laid length wise perpendicular to the axis of cable complete all as specified and directed by Engr-in-Charge.

Taking down GI pipe 20 mm bore medium grade and fitting and supply and fixing GI tubing medium grade 20 mm bore in any length with all fitting laid in trench and connecting up with water supply main complete all as specified and directed by Engr-in-Charge. (Excavation and earthwork shall be measured and paid for separetely under approprite item)

All as per item ser No 6 above here in before but 25 mm bore

All as per item ser No 6 above here in before but 40 mm bore

All as per item ser No 6 above here in before but 50 mm bore

S&F in replacment of gun metal globe or gate valve with iron wheel head screwed both ends suitable for galvanised pipe 20 mm bore complete all as specified and directed by Engr-in-Charge.

All as per item ser No 10 above here in before but 25 mm bore

All as per item ser No 10 above here in before but 40 mm bore

All as per item ser No 10 above here in before but 50 mm bore

M&L for disconnecting electric connection and pipe connection and taking out for non clog sewage pump motor capacity 10 HP including replacement of ball bearings and alignment of motor starter stator submersible pump & motor of capacity 10 HP from bore well and taking to workshop for repair and removal of burnt winding wire from motor and rewinding with new PVC insulated copper winding wire for submersible motor of same guage and weight to existing including replacement of, Motor bush, thrust plate coupling complete with key and alignment of motor stater's slote reassembnling the motor with pump and lowering it into bore well making it functional and testing complete all as specified and directed by Engr-in-Charge.

All as per item 14 above here in before but capacity 7.5 HP

All as per item 14 above here in before but capacity 5.0 HP

All as per item 14 above here in before but capacity 3.0 HP

All as per item 14 above here in before but capacity 5 HP monoblock pump set

S&F PVC insulated submersible cable 03 core 1100 Volt AC Supply stranded copper conductor of size 10 sqmm in replacement of old U/S cable complete all as specified and directed by Engr-in-Charge.

M&L for cleaning and surface dressing of plant area by cutting grass and excavation upto 30 cm depth, spraying chemical, laying polythene in excavated area and filling complete with provn of 63mm graded stone aggregate upto height 40cm complete all as specified and directed by Engr-in-Charge.

M&L for cleaning of semi under ground raw sewage sump of capacity 30000 galan collection chamber of 5.05 m depth & dia 6 m of the tank from ground level in RCC M-30 construction. removing of silt and sludgeto a distance not exceeding 50 Mtr from GL etc deposited inside the tank cleaniang entire internal surface of tank with bleaching powder and flushing with water marking Dt of cleaning with enamelled paint complete all as specified and directed by Engr-in-Charge.

M&L for cleaning of fine bar steel screen chamber of 25 mm x 25 mm thick flat 6 mm of the tank from ground level in RCC M-30 construction. removing of silt and sludgeto a distance not exceeding 50 Mtr from GL etc deposited inside the tank cleaniang entire internal surface of tank with bleaching powder and flushing with water and marking Dt of cleaning with enamelled paint complete all as specified and directed by Engr-in-Charge.

M&L for cleaning of Screen chamber in mild steel epoxy painted construction in RCC M-30 of size 2.00 m X0.3 m X0.45 m and sludgeto a distance not exceeding 50 Mtr from GL etc deposited inside the tank cleaniang entire internal surface of tank with bleaching powder and flushing with water marking Dt of cleaning with enamelled paint complete all as specified and directed by Engr-in-Charge.

M&L for cleaning of stilling chamber in RCC M-30 construcion size 1.30 m x1.30 m x1.30 m depth removing of silt and sludgeto a distance not exceeding 50 Mtr from GL etc deposited inside the tank cleaniang entire internal surface of tank with bleaching powder and flushing with water and marking Dt of cleaning with enamelled paint complete all as specified and directed by Engr-in-Charge.

M&L for cleaning of Equilization tank (EQT) in RCC M-30 construction with rung ladder of size L 6.00 m x W 5.00 m x D 4.5 m (including 0.2 m free board) and sludgeto a distance not exceeding 50 Mtr from GL etc deposited inside the tank cleaniang entire internal surface of tank with bleaching powder and flushing with water and marking Dt of cleaning with enamelled paint complete all as specified and directed by Engr-in-Charge.

M&L for cleaning of MBBR reactor chamber in RCC M-30 construction with rung ladder of size L 6.00 m x W 5.00 m x D 4.5 m (including 0.2 m free board) and sludgeto a distance not exceeding 50 Mtr from GL etc deposited inside the tank cleaniang entire internal surface of tank with bleaching powder and flushing with water and marking Dt of cleaning with enamelled paint complete all as specified and directed by Engr-in-Charge.

M&L for cleaning of Oil & greese trap/ grit chamber in RCC M-30 Construction of size 4.00 m x1.00m x 0.75m (depth including free board) and sludgeto a distance not exceeding 50 Mtr from GL etc deposited inside the tank cleaniang entire internal surface of tank with bleaching powder and flushing with water and marking Dt of cleaning with enamelled paint complete all as specified and directed by Engr-in-Charge.

S&F phase sequancer corrector with phase loss corrector system working on 415 Volt, 50 Hz, On/Off coil (switch) current capacity 18A, working voltage 12/24 Volt, Cut of voltage (Low) 330-370 (Adjustable), cut of voltage (High) 440-540 Voltage (Adjustable), Phase reversal System, Single phasing protection system, Time delay to start system 150 sec and Off switching time (two stop the system) for 10 HP submersible pump etc complete all as specified and directed by Engr-in-Charge.

All as per item No 28 here in before but current Capacity 32A,25HP

All as per item No 28 here in before but current Capacity 40A 30HP

All as per item No 28 here in before but cuurent Capacity 50A 40HP

Taking down old u/s bleching dozing pump along with all accessories and Supply and install connecing. Testing and commissioning of High Pressuure single Head adjustable "DECLIBAC" Dosing system Model No VST 1005 and VST 1006 of the following specification. Adjustble High Pressure 5 Kg/Sq. cm. power input 230V, 50 Hz, 40 SPM 1/30 fractional Horsepower, Max output 10 Ltr with mandatory accessories like lead Tubing, connecting ferrules, check valves, etc (A) Preparation tank Model No VST 1005 of net capacity 100 Ltr, FRP dosing tank dia 650 x net Height 375 + conical 300. Gross height with stand 1000 mm consisting of : (i) Water inlet line (ii) Outlet with stainer (iii) Drain (iv) overflow (v) conical bottom for sludge depositing (vi) Pot hole with cover (vii) level gauge (viii) Agitator 120 watt 900 RPM single phase flange mounted motor with plastic shaft and impeller. (B) Service Tank Model No VST 1006 dia 480 x height 575 net capacity 100 Ltr consisting of (i) water inlet line (ii) Dosing pump inlet arrangement (iii) Drain (iv) Overflow (v) Level Gauge (vi) inspection port (vii) Agitator 120 watt 900 RPM Single Phase flange mounted moto with plastic shaft and impeller (ix) provision of mounting Pump on Lid/wall Make : DECLIBAC or equivalent to ISI make as specified and directed by Engr-in-Charge.

S&F bettery 12 volts 180AH complete all as specified and directed by Engr-in-Charge.

M&L for replacement on load change over rotery type 4 pole 415 volt 200 Amp complete all as specified and directed by Engr-in-Charge.

Supply only orthotolidine reagenet for chlorine test in 500 ml bottle complete all as specified and directed by Engr-in-Charge.

Supply only Calcium based granuler disinfect suitable for treatment drinking water in 45 kg plastic drum complete all as specified and directed by Engr-in-Charge.

M&L and services for taking sample of sewage water in sterlised bottles from various borewells for Analysis of water for the following parameters and obtaining sample test report from Govt Recognized Laboratories: Note : 1. A certificate of approval / certification of Lab by Goivt Of India / State Govt shall be submitted by the contractor to the deptt. 2. Sample shall be submitted to the Labortory within 24 Hrs of collection of sample

Supply of Chlorine test kit with coloured ample with all testing fitments and OT solution in Rexene finish Box complete all as specified and directed by Engr-in-Charge. Make - RMCO or equivalent to ISI make as specified and directed by Engr-in-Charge.

Servicing the silancer assembly, remove the complte silencer assembly from DG set by removing nuts bolts complte, including opening the wall of silancer outlet remove the old aspectose rope on silencer complte, remove the blockage complte, reassemble the silencer with DG set with new gasket, nut, bolts & washers, gaswelding on damaged portion on silencer pipe complte DG set 62.5 KVA complete all as specified and directed by Engr-in-Charge.

Dismantling of FIP, injector nozzles includings connected accessories from 62.5 KVA Kirloskar DG sets and M/L for carrying out overhauling, calibration from authorised service centre, replacement of damaged spares if any and refixing complete all as specified and directed by Engr-in-Charge.

Supply and fill the Lub oil grade 10 w 15 for DG set of 100KVA-3nos, 62.5 KVA-1 no, 40 KVA-4 nos,30 KVA-2nos,,all asper the requirement, Make : Bharat petrolium/Indial oil complete all as specified and directed by Engr-in-Charge.

Taking out of unserviceable Dynamo Assy from 62.5 KVA DG Set including Supply & fixing new Dynamo assy to its original position complete all as specified and directed by Engr-in-Charge.

Supply, fixing and installation of Octagonal poles. Supply and install hot dip galvanized steel (IS 5986 Gr. Fe 510) Octagonal pole model NJOP 7 of 7.0 mtr long, top top die 70 mm botom dia 130 mm having thickness 3 mm having door operating of size 500 mm above ground level with CI Base plate of size 220x12mm having PCD 205 mm foundation J bolts length 700 mm nuts and screwes, No's of bolts 4 x 20 and having hot dip galvanized single plain arm bracket 1000 mm overhang on one side with 48.3 mm outer dia pipe of thickness 3.2 mm fixed on top with bolts and necessary earth work RCC/PCC work for the foundation of pole, including necessary form work and fare finish to exposed surfaces without using extra cement etc. complete all as specified and directed by Engr-in-Charge.

Supplying, laying, jointing and testing under ground XLPE insulated armoured heavy duty electric cable with aluminium conductor 1100 vols grade cross sectional area 16 Sqmm 4 core laid in trences, in floor, in duct, through pipes or along the pole including taking down old one complete all as specified and directed by Engr-in-Charge.

Taking down old unserviceable any type fitting and Supply and fixing Supply and fixing LED street light fitting 60 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed by Engr-in-Charge.

DUGGAL CONSTRUCTION CO