REPAIR TO ROOF CEILING, PLINTH PROTECTION, BRICK WORK, PLASTERING UNDER NHL AND OHL AREA REPAIR MAINT INCLUDING CLEANING OF SEWAGE LINE MANHOLE SEPTIC TANK SOAK PITS UNDER C1 AND C1A AREA AND REPAIR TO WOODEN, ALUMINIUM STEEL JOINERY AND CONNECTED W

Amount

Dismantling of AC corrugated sheets in roof covering including ridges, hips, valleys etc complete.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as per IS 15965: 2012 in roof covering fixed with self tapping screws complete.

S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as per IS 15965: 2012 in cladding to wall etc, fixed with self tapping screws as specified.

Dismantling timber scantlings (framed work) exc 40 Sqcm in section, in any position.

M&L for Mild steel work in tubular trusses, purlins, vetical posts including special shaped washer, angle cleats, fish plates, gusset plates, base/ bearing plates, bolts and nuts etc. complete using ERW or induction butt welded tubes conforming to 1161-1979 grade st 240 complete.

S&F MS flat iron wind ties for roof including all necessary drilling, bolting or riveting etc conforming to Fe-290 Gde E-165 complete all as specified and as directed.

Dismantling of ceiling boards/lining of any type and any thickness including cover fillets and timber frame work complete.

Providing and fixing inter locking metal grid (snap grid for false ceiling) of size 605 mm x 605 mm in true horizontal level, hot dipped galvanized steel sections (galvanized @ 120 grams/sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24 mm X 38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24 mm X 28 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200 mm x 600 mm and secondary cross “T” of length 600 mm and size 24 mm X 28 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200 mm X 600 mm panel to form grids of 600 mm X 600 mm and wall angle of size 24 mm X 24 mm X 0.4 mm. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 mm X 37 mm X 25 mm X 1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 mm X 30 mm X 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications and as directed by Engineer-in-charge.

M&L Providing and fixing Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions

S&F Solid PVC Wall Lining and solid PVC Partition consisting of 4mm thick printed colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing all as approved by Engr-in-charge.

S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing

M&L for PCC M-15 grade (Nominal mix) using 20mm graded stone aggregate as in Bed blocks, copings etc complete.

Demolition of brick work or stone boulder masonary built in cement mortar including all quoins arches pillars etc. but excluding ashlar facing dressed stone work and precast concrete articles

M&L for Brickwork with old size fly ash bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified.

M&L for brick work with old size fly ash bricks straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and as directed.

Taking down cement plaster of any description including racking out joints, hacking for key, scrubbing down with water etc complete

M&L for rendering 10mm thick in CM 1:6 on fair faces of Brick work/concrete surface and finishing the surface even and smooth without using extra cement complete.

M&L rendering 15mm thick (10mm + 5mm) plaster on fair face of brick work in CM 1:4 and surface finished even and fair by mixing liquid water proofing compound as per manufacturers instructions complete. Note :- Liquid WPC shall be measured & paid seprately under relevant item of this BOQ.

Supply only liquid water proofing compound hydroseal-W+ or eqivalent (for plaster hardening, to contol efflorescence & fungal growth) as approved by GE.

M&L for preparation of newly plastered surfaces of wall and applying two coats of cement base paint including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed.

M&L for preparing newly plastered surfaces of walls and applying two coat of oil bound distemper over a coat of Chalk whitening complete all as specified and as directed.

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15 cm thickness (below or above ground level).

M & L for 50mm thick in PCC M-10 grade (Nominal mix) as in plinth protection surface finished even and smooth without using extra cement all as specified.

M&L 100 mm thick PCC M-7.5 grade (Nominal mix) using 40mm graded stone aggregate as in sub base to floor.

M&L for Non skid coloured cermic ENDURA tiles 10mm thick n. exc. 0.11 Sqm set and jointed in neat cement slurry & pointed with coloured cement to match in floor over and including15 mm thick screed bed in CM 1:4.

Surface excavation n exc 30 mm and deep averaging 15 cm deep getting out in soft/loose soil complete.

Removing excavated material to a distance n.exc 50m and depositing where directed at a level n.exc 1.50m above the starting point

M&L for 75mm thick cement concrete M-7.5 grade (Nominal mix) using 40mm graded stone aggregate as in sub base floor.

M&L for sand filling including consolidation for laying paver block complete.

M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade made with grey cement and pigment complete all as specified and directed.

M&L for Chequered cement concrete tiles (with white cement and pigment) 30cm x 30cm x 25mm thick rubber moulded glossey finish, set, jointed and pointed in neat cement slurry in floors over & including 20mm screed bedding in cement mortar 1:4 complete all as specified and as directed.

Demolition of Stone slabs and tiles on roof of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar.

M&L for 18-20mm thick Machine cut Machine polished kota slab flooring laid over and including 20mm screed bedding in cement mortar 1:3 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

M&L for 18-20mm thick Machine cut Machine polished kota stone slab as in riser of steps, skirting, dado and pillar jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and incl 10mm thick plaster in cement mortar 1:3 complete.

M&L for 18-20mm thick Granite (of any type) slab bedded & jointed with grey cement slurry & pointed with white cement with admixture of pigment to match the shade of granite stone including cutting & polishing including fixing with adhesive.

Rounding to edges of stone slabs one edge, such as in steps,cooking platform, and other similar situations complete as directed by Engr-in-Charge.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises

M&L Non skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 sqm, in floors etc. Set and jointed in neat cement slurry and pointed in coloured cement to match over & including 15 mm thick screed bed in cement and sand mortar 1:4 complete all as specified and as directed.

M&L for coloured Glazed ceramic tiles in vertical surface 450x 300x 7mm thick set and jointed in skirting pointed neat cement slurry and pointed in white or colour cement to match over and including 10mm thick rendering as in backing coat in CM 1:4 complete all as specified and as directed .

M&L Non skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 sqm, in floors etc. Set and jointed in neat cement slurry and pointed in coloured cement to match over & including 15 mm thick screed bed in cement and sand mortar 1:4. complete all as specified and as directed.

All as per items No 40 but on vertical surfaces over and including 10mm thick rendering as in backing coats in CM 1:4 complete all as specified and as directed.

Demolition of mud in roofs any thickness including plaster and in any position and leaping over roof terrace, removing the demolished material of the primises and depositing where directed at a level n exc. 1.5 m above starting point, complete all as specified and as directed.

M&L APP based polymeric membrane not less than 3 mm tick, weighing not less then 3.5Kg/Sqm, reinforced with polyster non-woven fabric (weighing) not less than 150gm/sqm and upper side of membrane thermally insulated with while mineral gravel finish, uniformly embeded during manufacturing process thermally insulated shall be used. It shall be laid by toruch application. Side overlaps shall be 75 mm and the ends shall be 100 mm and all overlaps and jointed shall also be sealed by torch application. For parapets, membrane shall be taken to a height of minium 300mm and then inserted inside the parapet in a grooves. The same shall be finished by a membrane flashing over a coat of cold applied bituminous primer confiming to IS:[email protected] per Sqm complete all as specified and directed.

M&L for 40mm average thick PCC M-15 grade (Nominal mix) using 12.5 mm grade store aggregate stone agg) in floors/roof padding finishing the surface even and smooth with out using extra cement.

M&L for cement concrete tiles 25 cm x25 cm x20 mm thick machine pressed set jointd and pointed in neat cement slurry over APP membrance over and including 20 mm scred bedding laid in CM 1:4 complete and sesaling the joonts of tiles with themax premium apoxy paint of Make JK cement or equivalent.

Disconnecting existing tanks exc. 500 Ltr and n.exc. 1000 Ltr capacity setting aside lowering (if required) for repairs cleaning etc and hoisting if required, reconnecting and re fixing and wirting date of cleaning in thick white paint.

S&F 1000 ltr capacity Rotational moulded polythene triple layer water storage tank (cylindrical vertical with closed top) hoisted and fixed in position including dismantling of tanks all as specified and as directed by Engineer-in-Charge.

S&F in repairs 15mm bore fancy type Bib taps, cast copper alloy CP with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed

Taking down chowkhats or frame with shutter (without taking off shutters from the frame) area n.exc. 1.50 Sqm each and making good the disturbed surface complete all as specified.

Taking down Chowkhats or frames exc 1.5 sq. m but n exc 4 sq. m each and making good the disturbed surface complete all as specified.

S&F Pressed steel frame of size 105 X 60 mm for doors with one or more rebates including necessary fixing lungs, hinges, lock strike plate, etc, with a shop coat of red oxide primer complete all as specified.

S&F 125x60 mm Pressed steel frames made out of 1.25mm steel sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., with one shop coat of red oxide primer complete, as specified, supplied and fixed all as specified and as directed.

M&L cement concrete M-10 grade (Nominal mix) using 12.5mm graded stone aggregate as in bed blocks for fixing hold fasts and fillling of frame etc. all as specified.

S&F 35 mm thick flush shutters solid core construction with block board core and plywood fresh panel veneered type on both the side complete all as specified and directed by Engr-in-Charge.

S&F 35mm thick second class HW factory made glazed and gauged skeleton shutters open rebeted and prepared to receive glass, guaze etc (without sash bar) edges of framing plain chamfered or rounded fitted with cut and beads for securing glass, gauge etc size of shutters as specified in SSR Part-I section & clause 8.20(a).

S&F solid PVC door frame of size 50mm x47mm made out of 5mm plain colour PVC sheet reinforcement with MS square tube supplying and fixing in opening as per specification & sketch shown in sketch 8 of SSR part II.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20mm width stuck indie with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fittied in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F for 150 mm aluminium anodised barrel tower bolts of extruded section and fixed.

S&F in repair for 150 mm aluminium anodised barrel tower bolts of extruded section and fixed.

Supply and fix 250 mm long Stainless steel, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts complete all as specified.

Supply and fix in repair 250 mm long Stainless steel, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts complete all as specified.

S&F 150 mm long aluminium anodised handle fabricated type all as specified and as directed by Engineer-In-Charge.

S&F in repair 150 mm long aluminium anodised handle fabricated type all as specified and as directed by Engineer-In-Charge.

Supply & fix 100mm long but hinges medium weight cold rolled miled steel and fixed.

Supply & fix in repair 100mm long but hinges medium weight cold rolled miled steel and fixed.

S&F Aluminium floor door stopper 2 legs runner shoes at and 150mm long.

S&F in repair Aluminium floor door stopper 2 legs runner shoes at and 150mm long.

S&F 300mm size mild steel rat tail rod pattern door springs ISI marked including roller & roller plate etc complete.

S&F in repair 300mm size mild steel rat tail rod pattern door springs ISI marked including roller & roller plate etc complete.

S&F Steel windows with side hung shutters including Box type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded fixed to wall with one shop coat of redoxide primer complete all as specified and directed.

S&F Steel ventilator with top hung shutter including hinges, steel peg stay, including one shop coat of redoxide primer complete all as specified.

S&F powder coated (powder coating shall not be less than 50 microns of approved colour) aluminium frame for windows, ventilators (sliding, fixed or casement) with one or more rebates including joining cleat for fixing etc, complete all as specified.

S&F powder coated (powder coating shall not be less than 50 microns of approved colour) aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges,anodised alumnium snap beading, screws etc. complete all as specified

S&F Powder coated (powder coating shall not be less than 50 microns of approved colour) aluminium window and ventilator shutters, side hung/sliding type with or without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.) hinge type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified

S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed in position.

S&F in repair, Aluminium (Die cast) body Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified.

S&F 5mm thick sheet glass, ordinary quality and glazing fixed to aluminium frame in square exc. 0.5 square metre in each pane complete.

Hacking out old broken glass of any thickness size or quality from wooden/metal frame fixed with putty/beading & S&F 3 mm thick sheet glass, plain ordinary quality any size as required at site in each pane complete all as specified.

S&F 4 mm thick sheet glass, ordinary quality and glazing fixed in repairs to aluminium/ Steel/ wooden frame in square exc. 0.5 square metre in each pane complete.

S&F 4mm thick frosted glass, ordinary quality and glazing fixed to aluminium frame in square exc. 0.5 square metre in each pane complete.

M&L Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples.

S&F in repairs Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed in repairs with stainless steel wire staples/ screwed complete all as specified.

S&F in repair 20 mm dia, chromium plated curtain rod with fixing brackets, including CP decorative end holders, stop, rollers etc.complete all as specified.

M&L for preparation of new wooden surfaces any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

M&L for preparation of new steel surfaces over 10cm width or girth not other wise described and applying two coats of synthetic enamal paint over a coat of red oxide primer.

Cleaning of sewage lines which are blocked /filled with sludge, semi solid/material etc by roding manholes to manholes manuually or by sewage line/manholes. Manhole covers and removing the sludge to a non inhabitant area or buried into ground all as specified for the following internal dia of pipe. Note :- (i) Sewage line cleaned should function smoothly during entire contract period and measurement shall be made only once. (ii) Contractor shall be responsible to clear any further blocagkage without any extra payment till completion of work.

150 mm dia

200 mm dia

Cleaning and de-sludging water/ liquid/semi solid sludge in foul position from soak wells of any size depth or width by mechanically with pump and filling in the covered tank mounted on truck (Honey Sucker) and disposing of the same out side of MOD land complete all as specified.

Cleaning and de-sludging water/ liquid/semi solid sludge in foul position from septic tank of any size depth or width by mechanically with pump and filling in the covered tank mounted on truck (Honey Sucker) and disposing of the same out side of MOD land complete all as specified.

Cleaning of blockage of any type of wc (Indian/pedestal) from WC pan upto Ist manhole in single/double storied bldg including resetting/refitting of asccess door in soil pipe where open without causing any damage to the WC pan 'P' or 'S' trap and pipe including fitting complete all as speciffied

Cleaning of blockage of any type in Nahani trap provided in bath room, kitchen and indoor water pipe of kitchen sinks and WHB and removing all the sludge and foreign material from the trap and waste pipe from blocked trap to gully trap/ surface drain wherever opened or without causing any damage to the trap and pipe including fitting distance of gully trap from outer wall of bldg upto 2m complete all as specified

Excavating in trenches n exc 1.5m wide and n exc 1.5m in depth, for foundation, etc. and getting out in soft/ loose soil complete all as specified.

Excavating in trenches n.exc 1.5m wide exc 1.5m and n exc 3m in depth, for foundation, etc. and getting out in soft/ loose soil complete all as specified.

Demolition and breaking up 150 mm dia drain pipe (salt glazed ware, AC,reinforced concrete) set in cemnt mortar and removing rubbish outside MD land all as specified.

Demolition and breaking up 200 mm dia drain pipe (salt glazed ware, AC,reinforced concrete) set in cemnt mortar and removing rubbish outside MD land all as specified.

M&L PCC M-7.5 (Nominal mix) using 40 mm graded stone aggregate as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150 mm dia pipe complete all as specified.

M&L PCC M-7.5 (Nominal mix) using 40 mm graded stone aggregate as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 200 mm dia pipe complete all as specified.

M&L salt glazed stone ware drain pipe 150 mm bore grade 'A' laid in trenches and jointed with CM 1:1 complete all as specified

M&L salt glazed stone ware drain pipe 200 mm bore grade 'A' laid in trenches and jointed with CM 1:1 complete all as specified

Returning filling in soil including spreading levelling watering and well ramming in layers not exc 25 mm thick complete.

M&L for rendering 15mm thick on other than fair faces of brick work external faces in manhole in CM 1:4 including finishing the surfaces even & fair all as specified

M&L for rendering 15mm thick on brick work internal faces in manhole in CM 1:4 including finishing the surfaces even & fair all as specified

M&L for brick work with old size fly ash bricks straight or curved on plan exc 6m mean radius built in CM 1:4 complete all as specified and as directed.

M&L for preparing newly plastered surfaces of wall and applying three coat of Colour wash on walls complete all as specified & directed.

M&L for preparing newly plastered surfaces of wall and applying three coat of white wash on walls complete all as specified & directed.

M&L for preparation of newly plastered surface of walls and applying two coat of cement base paint over a coat of primer including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed.

M&L for PCC M-10 grade (Nominal mix) using 20 mm graded stone aggregate as in plinth course, string courses etc. complete all as directed.

M&L for PCC M-10 grade (Nominal mix) using 40 mm graded stone aggregate as in foundation, filling and mass concrete complete all as directed.

M&L for PCC M-15 grade (Nominal Mix) using 20mm graded stone aggregate Providing, cement concrete in roof kerbs benching channel or mud stops, rounded or chamfered on edges finishing even and smooth without using extra cement complete all as specified and directed.

Demolition of reinforced concrete (cutting reinforcement as required to facilitate demolation of cover slab and similar suspended work and removing debris out side MD land all as specified.

M&L reinforced cement concrete M-25 grade (Design mix) as in slab supported on walls, beams and columns in floor, roof, beams and shelves etc for soak well/septic tank in running and manhole cover slab with plain fair faces and set in CM 1:4 condition complete all specified

M&L for use & waste of steel form work to soffits of suspended slabs such as roof slabs, landing and similar work n exc 200 mm thick, curved, plain in running condition complete all specified (rough finished surfaces)

M&L for TMT bars 6 to 8 mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hookingnends and bindingn with and includingnmild steel wiren (annealed) not lessnthan 0.9mm dia ornsecuring with clips

All as per item No. 110 above but 10mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete.

S&F in repairs 110 mm dia PVC (SWR) pipes type 'A' single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F in repairs 75 mm dia PVC (SWR) pipes type 'A' single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F in repair 110 mm dia PVC (SWR) bends any radius complete all as specified.

S&F in repair 75 mm dia PVC (SWR) bends any radius complete all as specified.

S&F in repair 110mm PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S&F in repair 75mm PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S&F in repair 100 mm dia PVC (SWR) bends with aceess door any radius complete all as specified.

S&F in repair 75 mm dia PVC (SWR) bends with aceess door any radius complete all as specified.

S&F in repair 110mm PVC (SWR) vent cowl complete all as specified and directed.

S&F in repair 75mm PVC (SWR) vent cowl complete all as specified and directed.

SHRI RADHAYSHYAM JHA

BHARDWAJ CONSTRUCTIONS

JWALA ELECTRIC CONTRACTORS

R N AGRAWAL