PROVISION OF GD ROOM POST NO B-37 AND PROVN OF CGI SHEETS, FALSE CEILING TILLING AND ALLIED INFRA IN BLDG NO T-57A, T-77 AND EQUIPMENT PARK (P-43, P-49 AND P-53) OTM ACCN OF 104 AD REGT UNDER GE (ARMY) DHAR ROAD UDHAMPUR

Amount

Surface dressing n exc 15 cm deep in soft/loose soil

Surface excavation n. exc 30 cm deep and averaging 15cm deep and getting out soft/loose soil complete all as specified and directed.

Excavation in trenches, not exceeding 1.50m wide and not exceeding 1.5m in depth etc not exceeding 10 Sqm on plan for shafts, cesspits, manholes, pier holes, foundation, stay assembly/ laying of cable/ errection of poles etc and getting out in soft/loose soil complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in cement concrete in foundations, filling and mass concrete complete all as specified and directed.

M&L for PCC 1:2:4, Type B-1 using 20mm graded stone aggregate as in coping,benching, even and smooth without using extra cement etc complete all as specified.

M&L Plain Cement concrete type C2, 1:3:6 using 40mm graded aggregates in foundations, filling and mass concrete

M&L Reinforced cement concrete M-25 using 20mm graded aggregates in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete

All as per item No 7 above but in columns

All as per item No 7 above but in beams, cantilevers, bressummers, lintels over 1.5m span

All as per item No 7 above but in Chajjas

M&L Reinforced cement concrete M-25 using 20mm graded aggregates in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed

M&L Providing Plain Cement concrete type B1, 1:2:4 using 20mm graded aggregates in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, , lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed

M&L PCC 1:2:4, type B1 using 20mm graded aggregates in surface channels and drains surface finished even and smooth using extra cement.

M&L Finishing cement concrete surface even and smooth using extra cement.

M&L Form work to sides of rough finished flat surfaces of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed

M&L Form work to sides of rough finished square, rectaungular or polygonal surfaces of of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

M&L Formwork to sides and soffit of rough finished flat surfaces of soffits of floor or roof beams, beam haunch- ings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed

M&L Form work to rough finished flat surfaces of chullah hoods, chajjas, troughs and similar items including edges complete all as specified and directed

M&L Form work to rough finished flat surfaces of soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping)

M&L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

M&L mild steel TMT bars 8mm dia and over cut to length , bent to shape required including cranking bending etc and binding with mild steel wire (annealed ) not less than 0.90 mm dia as in reinforcement complete all as specified and directed.

All as per item No 21 above but 5mm dia and over upto and including 10mm dia as in stirrups etc complete all as specified and directed.

M&L Brick work with subclass 'B' bricks, straight or curved on plan exc 6m mean radius in CM 1:6 complete all as specified and directed.

M&L Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM 1:4 complete all as specified and directed.

M&L Brick work with subclass 'B' bricks, straight or curved on plan to any radious in half brick thick walls in CM 1:4 complete all as specified and directed.

M&L for rendering 15 mm thick cement plaster in CM 1:4 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement with WPC 3% weight of cement complete all as specified and directed. (WPC shall be measured and paid separately)

M&L for 10 mm thick rendering on fair faces of brick work or cement concrete surfaces in cement mortar 1:4, finished fair and even without using extra cement incl mixing of water proofing compound complete all as specified. (Note: Water Proofing compound shall be measured and paid for separately)

Supply only integral water proofing compound,

M&L 15mm thick cement plaster in 1:4 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed

M&L Rendering 15mm thick cement plaster in CM 1:6 on other than fair faces of brick work or concrete sur- faces finished even and smooth without using extra cement complete all as specified and directed.

M&L Rendering above but 10mm thick in CM 1:3 in Ceilings finished even and smooth without using extra cement complete all as specified and directed.

M&L Preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified.

M&L Preparation of new plastered surfaces of wall and applying two coat of oil bound distemper over a coat of alkali resistant primer complete all as specified.

M&L applying two coats of oil bound distemper on walls including 2 mm thick wall care putty, on new plastered surfaces, preparatory to distempering over and including a coat of primer complete all as specified and as directed

M&L Preparation of new plastered surfaces of wall and applying three coats of white wash on wall ceilings complete all as specified.

M&L applying two coats of oil bound distemper on walls on old plastered surfaces, preparatory to distempering over and including a coat of primer complete all as specified and as directed

M&L for two coats of synthetic enamel paint on steel surfaces, over a coat of red oxide primer incl preparation of new steel surfaces 10cm in width or grith not ohter wise described complete all as specified and directed.

M&L for two coats of synthetic enamel paint on wooden surfaces, over a coat of pink primer incl preparation of new steel surfaces 10cm in width or grith not ohter wise described complete all as specified and directed.

S&F Pressed steel frames size 125 mm x 60 mm for doors/windows with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed.

M&L PCC M-10 type C0, 1:3:6 using 12.5mm graded stone aggregates for filling in steel frames

S&F Steel window made up of box steel section of 16 gauge MS Sheet in outer frame, shutter frame and centre frame, with fixed type partly glazed and partly gauzed with outer side glazed shutter and inner side wire mesh shutter fixed with suitable steel handle dovetailed or welded with each shutters pannels complete with necessary clit and stopper all as specified as directed.

S&F Steel ventilator made up of box steel section of 16 gauge MS Sheet fixed type partly galzed and partly gauged inner frame and centre frame, including outer side glazed shutter and inner side wire mesh shutter fixed with MS clip consisting with dovetailed or welded with each pannels complete with necessary clit and stopper all as specified as directed.(MS Gaurd bar/griil work will be measured and separetly)

S&F 35mm thick second class hard wood Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F 35mm thick second class hardwood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. with two Nos Muntines edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing

S&F Galvanised steel wire cloth. 0.56 mm nominal dia of wire and average width of aperture 1.00mm complete all as specified and directed.

S&F 4mm thick Sheet glass, ordinary quality and glazing with oil putty in square n. exc 0.5 sq. m in each pane complete all as specified and directed.

All as per item No 50 above but pin headed.

S&F 200mm long Aluminium anodised, barrel tower bolts of ex- truded section and complete all as specified and directed.

S&F 150mm long anodised aluminium alloy handles, fabricated type complete all as specified and directed.

S&F MS 300mm long ordinary rat tail rod pattern spring incl roller and plate complete all as specified

S&F 250mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes. framed guard bars, barred iron doors, ladders. framed balusters. walk ways. railings. framework of water tanks and similar work con forming to Fe.290.Gde-E-165 complete all as specified and directed.

S&F welded steel wire fabric supplied and fixed complete to wood or steel members exc 4 Kg per Sqm complete all as specified and directed.

M&L 50mm thick Cement conrete type C2, 1:3:6 using 40mm graded stone aggregates for plinth protection laid in alternate panels and finish even and smooth without using extra cement providing 6mm wide joints along wall and between bays throughout the thickness of plinth protection fixed with mastic filling comprising one part of bitumen 85/25 grade and three part of sand by weight complete all as specified.

S&F vitreous china squatting pan, Orissa pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe), including connection to trap, and to flushing pipe, anti syphonage pipe, etc., complete including making good to floor complete all as specified and directed.

S&F 10 litres PVC valveless, syphonic action type, flusing cistern low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed.

Supply only flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern complete all as specified and directed.

S&F vitreous china wash basin, white, flat back, size 550x 400 mm incl 32 mm waste fittings, brass, chromium plated for glazed ware sinks, basins etc with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed excluding taps, chain and plug and porcelain stopper but including brackets complete all as specified and directed.

S&F CP Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 170gms)

S&F Soap dish, vitreous China white, approximate size 160x 160x90mm.

S&F Vitreous China urinals, bowl type (back or corner wall type) size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe complete all as specified and directed.

Supply only Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified and directed.

S&F 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F 75mm dia PVC (SWR) bends complete all as specified and directed.

S&F 110 mm PVC (SWR) bends complete all as specified and directed.

S&F 110mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

All as per item No 68 & 69 for 75mm bore pipe but with access door complete all as specified and directed.

S&F 110mm dia PVC (SWR) junction single (Single T) equal or unequal with access door complete all as specified and directed.

S&F 75mm dia PVC (SWR) type B Pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed

All as per item No 70, 71 & 73 for 110 mm bore pipe but 110 dia complete all as specified and directed.

S&F 100mm long Butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and directed

S&F 15 mm bore dia Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixedcomplete all as specified and directed

S&F 15mm bore dia Bib taps long body fancy type cast copper alloy chromium plated with capstan head, screwed down, screwed for iron pipe or for brass ferrule fixed complete all as specified and directed.

S&F 15mm bore dia CP stop valve/angle valves cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete.

S&F PVC connections 15mm size with PTMT nuts of length 450mm

S&F fancy type brass chromium plated shower rose 125mm size with CP swiveled type arm fixed to steel pipe or union complete.

M&L 15mm bore steel tubes "medium grade" galvanised with all fitting and fixed in walls ceilig or laid in floors/trenches complete all as specifeid and directed.

M&L 20mm bore steel tubes "medium grade" galvanised with all fitting and fixed in walls ceilig or laid in floors/trenches complete all as specifeid and directed.

M&L 25mm bore steel tubes "medium grade" galvanised with all fitting laid in trenches/ floors complete all as specifeid and directed.

S&F 32mm dia Waste coupling of PTMT (half or full threaded) . (Minimum weight 32mm- 45gms/40mm-60 gms)

M&L filling under floors or in foundations with approved soil including spreading, levellig in layers n exc 25cm thick and well ramming, watering as reqd complete all as specified and directed.

M&L for 100 mm thick cement concrete type D-2, 1:4:8 (40 mm graded stone agg) as in levelling course for laying floor finishes.

M&L 75mm thick Cement conrete type D2, 1:4:8 using 40mm graded stone aggregates as in sub-base, sub-floors, floors etc complete all as specified and directed..

M&L Machine cut kota stone slab flooring 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including 20mm thick screed bed in 1:4

M&L Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm (size 300x300), in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:6

All as per item No 90 above but in skirting includig 10mm thick backing coat in CM 1:3

M&L for Glazed ceramic coloured tiles 300x450x 7mm thick on vertical surfaces of wall set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 10mm thick rendering in CM (1:4) backing of wall tiles such as dado/skirting in vertical surface complete all as specified and as specified.

Roof Treatment for non-accessible roof :- (a) 15 mm thick cement plaster in cement mortar 1:4 on roof surfaces finished even and smooth without using extra cement, incl water proofing compound, (b) Priming the roof surface with bituminous primer conforming to IS-3384 @ 0.30 ltrs/Sqm and applying a coat of hot blown 85/25 grade bitumen conforming to IS-702 @ 1.20 Kg/Sqm and thereafter provide polymeric water proofing membrane (five layered) of weight not less than 3Kg/Sqm with center layer core of 90 micron high molrcular density polyethylene film followed by another coat of semi hot blown 85/25 grade bitumen @ 1.20 Kg/Sqm blinded with fine sand in dry condition @ 0.50 Kg/Sqm Top surface of roof after carrying out treatment as specified hear-in-above shall be provided with 2 coats of aluminium paint over a coat of primer as per manufacturing's instructions complete all as specified and directed. Note:- Note:- WPC shall be measured and paid separately under respective item

M&L 40 mm thick PCC 1:2:4 nominal mix, type B-0, using 12.5 mm graded stone aggregate in two layers of 20 mm each MIXED WITH WATER PROOFING COMPOUND AS PER MANUFACTURER INSTRUCTIONS on roof surfaces, surface finished even and smooth without using extra cement, complete all as specified. Note:- WPC shall be measured and paid separately under respective item

Chicken wire mesh of size 12.5 mm and wire dia 0.51 mm (24 SWG) hexagonal construction, stretched firmly for roof treatment, complete all as specified

M&L Termite Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured)

M&L Termite Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface

M&L Termite Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area

S&F rotational moulded polyethylene water storage tanks 1000 litres capacity (cylindrical vertical with closed top) tripple layer constructed with threaded tank cover hoisted and fixed in position complete all as specified and directed

S&F 20mm dia Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed

S&F Gun metal globe or gate valves high pressure with screwed for iron pipe or for unions of 15 mm bore and fixed in repairs, all as specified and directed

S&F Gun metal globe or gate valves high pressure with screwed for iron pipe or for unions of 20mm bore and fixed in repairs, all as specified and directed

S&F Gun metal globe or gate valves high pressure with screwed for iron pipe or for unions of 25 mm bore and fixed in repairs, all as specified and directed

Removing excavated soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete.

Returning, filling in including spreading, levelling, watering and well ramming in layers n.exc 25cm thick.

S& F 20mm dia ms pvc coated curtain rods with side globes and holding brackets fancy type all as specifieed and directed

Supply & fixed Stain less steel peg set of six as approved by Engineer-in-Charge.

Providing kitchen cabinet / cup board shutters in required size at site made out of 18mm thick MDF made out of 18 mm thick one side decorative lamination PVC sheet complete all required etc. The panels shall be fabricated using adhesive and secure as required. All edges shall be covered with 2 mm thick edge bonding taps or 90 degrees edge bent finish as per manufacturers instructions.

M&L for 60mm thick factory made machine pressed precast concrete interlocking paver block any shape and size conforming to ISI 15658-2006 , with grey cement and pigment approved by GE & laying over and including 25mm thick sand cushion incl watter and ramming (Compacted) and joints filled with sand complete all as specified and directed.

M&L for pre cast cement concrete in kerb stone M-15, 1:2:4 type B-1, using 20 mm graded stone agg with solid blocks of size 300x300x100mm and setting with cement mortar (1:3) and pigments, complete as in kerbs or mud stops, rounded or chamfered on edges complete including excavation, RFR and

M & L for 150mm bore salt glazed stonware drain pipe grade 'A' conforming to IS 651-1972 laid in trenches and jointed in CM 1:1 all as specified and directed.

M & L cement concrete aggregate bed to drain pipe 150 mm dia including packing under and completely surrounding pipes with concrete after they are laid and tested in cement concrete 1:4:8 type D 2 using 40mm graded stone aggregate complete all as specified and directed.

Cutting into existing man holes for connecting new drains making good to pipes and rendering cutting out existing benching for and forming branch channel (1/2 round or ¾ in section) in cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) surface smooth finished and reforming benching as required for internal dia of pipe 150mm all as specified and directed .

M&L for precast cement concrete 1:2:4 type B1 using (20mm graded stone aggregate) as in slab for manhole cover complete all as specified and directed.

Extra for forming girth n exc than 30cm deep and all as specifed and directed

Construction of septic tank for 25 users ( brick construction) complete all as shown on drawing No CEUZ/ TD/1202/03 sheet 1/2 and 2/2 dated 14/10/2014 and 11/05/2007 and as specified and as directed by Engr-in-Charge. Note : Rate Exacavation, returing filling and removal deemed to be included in this item.

Construction of Sokage well of size 1.8 mtr dia and 3,00 Mt deep (Internal dimensions) (Brick construction), complete all as specified and as shown on drawing no CEUZ/TD/1202/03 sheet 1/2 and 2/2 dated 14/10/2014 and 11/05/2007 respectively. Note : Rate Exacavation, returing filling and removal deemed to be included in this item.

M&L construction of brick masonery valve pits of size 600x600x600 mm internal diamension with brick work in cement mortar (1:4) including excavation and earth work, concrete work 3mm thick MS sheet cover with locking arrangement hinges and handle rendering work, painting to all steel surfaces with two coats red oxide primer complete and all as directed and including demolition of existing damaged valve pit and removing complete all as specified and as shown in drawing No cEUZ/TD/1500/15 sheet 1/1 dt 12.01.2015 . Note : Rate Exacavation, returing filling and removal deemed to be included in this item.

M&L Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc all as specified and directed.

M&L brushing neat cement slurry with 3.00 Kg of cement per sqm all as specified and directed

M&L 25 mm thick cement concrete type B-1, PCC (1:2:4) using 20mm graded aggregate

M&L for Screed bed or bedding layer of mortar 10 mm thick in CM (1:4) for laying floor finishes. Note : Using only course sand in screed bed.

M&L for vitrified ceramic tiles light shade 10mm thick (square/rectangular) polished, area of each tiles not exc 0.36sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified.

S&F pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S&F roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.

S&F framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete

S&F plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5 cm but n.exc 10 cm long of 16 to 20 mm neck diameter all as specified

S&F 200 mm long mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed.

S&F 150 mm long mild steel barrel bolts, stove enamelled black, with bright bolt and fixed

S&F 35 mm thick flush shutters, solid core constructions, with block board core and plywood face panels commercial type on both side complete all as spwcified and as directed

S&F factory made, 2nd class hard wood, 35mm thick glazed and skeleton shutters, open rebated and prepared to receive glass/gauge etc. (without sash bars) edges or framing plain, chamfered or rounded fitted with cut or mitered beads for securing glass etc. size of members of shutters as specified in SSR Part-I section 8.20 (a), all as specified and directed by Engr-in-Charge

Providing & fixing false ceiling with gypsum based ceiling tiles and frame work (with aluminium foil on one side) of size 595x595 mm of thickness not less than 9 mm including with GI powder coated frame angle/tee grid frame work for ceiling with following specifications (a) S&F Angle of side 25x25x1 mm powder coated (b) 25x25x1 mm GI powder coated at bottom tee as in main member (c) 25x25x1 mm thick GI powder coated at bottom tee as in cross members (d) S&F 1.6 mm dia GI wire suspenders along with adustable clamps to maintain leveling including fixing to ceiling fasteners manufacturers instructions complete. MAKE: VINYL TOUCH of LaGyp (LAFARGE) or equivalent in GYPROC (SAINT GOBBAIN)

S&F galvanised mild steel wire cloth, 0.63 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or galvanised wire staples complete all as specified

M & L for concealed point wiring for One light /Fan/Bell point controlled by one switch 6/5 Amp one way single pole on wall and ceiling/roof with necessary fixing arrangements with PVC-FRLS insulated and unsheathed copper multi-stranded conductor of size 1.5 Sqmm, 1100 volts grade drawn in and including rigid non metallic white / ivory PVC conduit medium grade ISI marked not less than 20 mm dia with all conduit accessories/ fittings such as junction boxes, bends, tee, elbow etc including anodized MS sunken boxes made out of MS sheet of thickness not less than 1.6 mm with earth dolly and Bakelite laminated sheet 3mm thick ISI marked for fixing of switches / sockets, fan regulators, wall mounting fittings, door bell & bulkhead etc with MS screw and cup washers including PVC-FRLS insulated and unsheathed copper multi-stranded conductor of size 1.5 Sqmm, 1100 volts grade for continuous earthing including cutting the chases and making good the surface by cement mortar (1:3) and for matching / finishing of new surfaces either by means of plaster of peris/ Putti or distemper / colour wash with same existing colour surfaces all as specified and directed by Engineer-in-Charge for the following:-

All as per item No 137 here-in-before but for One 3 pin 6/5 Amp socket outlet controlled by one switch independent board.

All as per item No 137 here-in-before but for power point wiring with 2.5 Sqmm PVC-FRLS insulated, unsheathed, copper conductor, stranded 1100 volt grade cable and 1.5 Sqmm PVC-FRLS insulated, unsheathed, copper conductor, stranded 1100 volt grade cable as continuous earth lead.

Supply & Fixing SPN Distribution Box, double door of protection grade IP 43 in fine powder coated, matt finish with best CRCA sheet, fitted with shrouded neutral, insulated pin type copper bus bar, Din rail, earth bar of 8 way, confirming to IS 13032 & 8623 complete all as specified and directed.

Supply & Fixing MCB SPN, 32 Amps 240 volts, AC , 10 KA breaking capacity 'C' Series,"ISI marked and conforming to IS 8828/IEC 60898-1 complete all as specified and directed.

Supply & Fixing MCB SP, 06 to 32 Amps 240 volts, AC , 10 KA breaking capacity 'C' Series,"ISI marked and conforming to IS 8828/IEC 60898-1 complete all as specified and directed.

S&F ceiling rose, surface bakelite, 65mm x 50mm, two to three terminals complete all as specified and as directed.

S&F switch piano flush type (ISI marked), single pole, one way 6 Amp, 240 Volts complete all as specified and as directed.

S&F socket outlet 3 pin, 6 Amp piano flush type including complete all as specified and as directed.

S&F socket outlet, 2 in 1, 3/5 pin 6 / 16 Amp, piano flush type complete all as specified and as directed

S&F switch piano flush type (ISI marked), single pole, one way 16/15 Amps, 240 Volts including complete all as specified and as directed.

S&F Wall mounted LED batten 18/20 Watt with 01 No LED tube rod, extruded aluminium heat sink provided for efficient heat dissipation and integrated electronic driver complete all as specified and directed.

Supply & Fixing medium step type fan regulator 240 Volt AC, socket size, medium step" ISI marked complete all as specified and directed. Make -Havells/Cona/Anchor/Legrand

Supply and fix ceiling fans copper wounded, bouble ball bearing, complete with three blade, down rod suitable size, accessories 230V, 1200mm sweep, energy saving fans, white colour including 3 core PVC insulated seathed flexible wire suitable size suitable length as requited at site and connection with ceiling rose and marking " MES NO- ,Unit -GE(Army) Dhar Road" with black enamelled paint with stancil complete all as specified and directed Make Havells/Crompton/Bajaj Note :- Contractor will submit inventory for installed ceiling fan duly signed by user unit QM/OC/CO.

Supply & fix exhaust fans AC single phase 230/ 240 V of size 300 mm sweep with louver alongwith cutting of hole in brick wall for venilation of ex fan 300 mm dia and making goog disturbed surfaces and painting as existing and provide mosquto proof net with wooden frame rectungular shape connection with ceiling rose and marking " MES NO- ,Unit -GE(Army) Dhar Road" with black enamelled paint with stancil complete all as specified and directed Make Havells/Crompton/Bajaj Note :- Contractor will submit inventory for installed ceiling fan duly signed by user unit QM/OC/CO.

S&F LED building security light 35 watt, 230V complete with all accessories and including connecting up to ceiling rose with 0.5 sqmm three core copper flexible conductor cable, One GI medium grade suitable size dia bracket of total length 50 cm and fixed to wall with 2 Nos MS Clamp and fastener all as specified and directed.Make Havells/Crompton/Wipro

M&L for earthing as per IS:3043 with galvanized steel earth plate electrode 600 x 600 x 6.0 mm thick buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metre below normal ground level connected to galvanized iron wire 4 mm dia (8 SWG) as earthing lead protected by GI pipe medium grade 15 mm bore for protection of GI earth wire and 20 mm dia GI pipe medium grade for watering with alternate layers of charcoal /coke and salt including all accessories like nut, bolts, reducer, nipple, wire meshed/screened funnel and making brick masonry finished chamber of internal size 300 mm x 300 mm x 300 mm with concrete base, covered with PCC cover which shall be embedded in the block masonry including excavation works, refilling, connected to main switch/MCB DB for feeding the electric supply to domestic quarters compete all as specified as shown in electricall plateNo. 3 of SSR Part-I and testing of earth resistance as required. Note : Earthing lead/G.I.Earth wire upto 7.5 metre length shall be deemed to be included in quoted unit rate beyond 7.5 metre, the same shall be measured and paid separately).

M&L for dry Sand cushioning in trenches for protection of cable including watering and consolidation all as specified and directed. Note: Punned thickness shall be considerd for measurment purpose

M&L for well burnt brick sub class B old size laying in trenches perpendicular to axis of the cable complete all as specified and directed.

Material and labour for fixing or passing through pipe, laid in trenches or fixed to pole/wall or fixed to LT panel board, 1100 volts grade heavy duty cable with PVC insulated stranded aluminium conductor served with inner sheathing of PVC tape, armoured with galvanised steel wire or tape and overall PVC sheathed 16 Sqmm 2 core with required aluminium cable lugs all as specified and directed. Make of Cable : Havells, Polycab, Gloster,Finolex

Machine cut Kota stone slab 20-25 mm thick as in riser, steps, skirting dado and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including 10mm thick rendering in cm (1:3) as packing of wall tiles such as dado/skirting in vertical surface complete.

SHIVAE CONSTRUCTION

K S BUILDERS

M/S GURU DEV BUILDERS

M/S GH MOHAMMAD DAR

TARUN BUILDERS

shivom builders