Construction of Dormitary Hall

Amount

Earth work excavation for foundation (for narrow excavation) in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

Supplying and filling in foundation, basement, etc with filling crushed stone sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Cement Concrete 1:5:10 (One Cement, Five crushed stone sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)

Beams & Slabs

Ground Floor Roof Level

First Floor Roof Level

Terrace Floor Level

Columns

Columns upto Substructure

GF Lvl to 1st Floor Lvl

1st Lvl to Terrace Floor Lvl

Above Terrace Floor Lvl

Providing and laying in position, standardised concrete Mix M-20 Grade in accordance with IS 456 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/m3 and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m) 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS standards. (No separate payment will be made by the Department for the excess usage of materials).

For foundation

GF Lvl to 1st Floor Lvl

1st Floor Lvl to Terrace Floor lvl

Above Terrace Floor Lvl

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Brick work in following Cement Mortar using best quality II class Ground moulded chamber burnt bricks of size 9" x 4-3/8" x 2-3/4" for foundation and basement including curing, etc., complete complying with standard specifiction.(In Cement Mortar 1:5)

Foundation & Basement

Brick work in following Cement Mortar using best quality II class Ground moulded chamber burnt bricks of size 9" x 4-3/8" x 2-3/4" for foundation and basement including curing, etc., complete complying with standard specifiction.(In Cement Mortar 1:6)

Ground floor

First Floor

Terrace Floor

Brick partition walls of 11.50cm thickness using best qualityII class Ground moulded chamber burnt bricks of size 9" x 4-1/2" x 3" in Cement Mortar 1:3 (One Cement and Three crushed stone Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

Ground floor

First Floor

Supplying and FILLING GRAVEL Supplying and filling in 'foundation and basement with filling crushed stone sand in layers of not more than 15cm.thick well rammed watered and compacted -1m3 etc., complete complying with standard specification.

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Plastering with Cement Mortar 1:5 (One cement and Five Plastering sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Plastering with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 12mm thick mixed with water proofing compound conforming to BIS at 2% by weight of cement used including finsihing, curing, etc., complete in all floors complying with standard specification and as directed by the departmental officers.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no crushed stone sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Crushed stone Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Supplying and painting the walls with two coats of cement paint over one coat of cement primer as instructed by the departmental officers including preparation of surface curing, etc., complete in all floors complying with standard specifications (The colour and shade of the cement paint shall be got approved by the Executive Engineer before use of work).

Paving the floor with best quality Vertified Tiles of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three crushed stone sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with pre-polished concrete anti-skid step tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three crushed stone sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three crushed stone Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works) Self Designed Colour Ceramic Tiles of size 305 x 305 x 6mm (Observed Data)

Dadooing walls with following best approved quality, white / colour glazed tiles of following sizes set in Cement Mortar 1:2 (One Cement and Two crushed stone sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.

UPVC Window Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work.

Supplying and fixing of Flush door shutter using Teak wood frame of size 127mm x 76mm and Door shutters Single leaf in position using 35mm thick solid core Flush shutters with teak play on both sides with teak wood lipping alround including cost and labour for fixing the hold fasts and furniture fittings etc.,complete as directed by the departmental officers complying with standard specification.

Supplying ,fabricating and fixing in position of steel frame without bottom frame, of size 100X60mm rectangular section with necessary rebate 30mmX15mm, to host the shutter,using 1.25mm thick (18 guage) CRCA cold rolled frame steel plate confirming to ISI specified ensured of right butt joint riveted hold assembly with nylon insert,not be welded with special purpose hard ware.Proclaimed including phopating as per ISI with rust preventive primer ready to assemble condition for easy installation at site including dismantling,making necessary chipping and holes in RCC columns, walls with power drills to the extent required ,including providing concrete 1:2:4 inside the box curing etc complete.The cost includes the cost of hold fast ,plastic bush, insert receiver,rubber bottom,shock absorber etc complete as directed by the departmental officers in all floors.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase near wet riser using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick will be provided with tubular supports made of 304L Grade Stainless Steel pipe of 25mm dia of 1.60mm thick welded to the railing. The supports will be grouted into the wall and provided with 93.00mm thick Stainless Steel circular base plate of 304 Grade. The rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing, bonding, cutting, grinding, conveyance, welding charges, electrical charges, etc. complete

Supplying and fixing mild steel grill Gate including cost conveyance of all materials and fixing in position including priming coat etc complete with standard specifications.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

UPVC Ventilator Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Supplying and laying of Interlocking Paver Block Stone 60mm thk. Over a base layer of crushed stone sandfilling incl. Cost of materials laying and Labour charges etc.,

Precast Kerb Works - R.C.C. 1:2:4 precast slab using 20mm size HBG jelly excluding cost of steel but including molding, laying concrete curing finishing and fixing etc., complete

Supplying and fixing in position White /Colour Special Delux Model Glazed Cascade Type equivalent wall mounted european water closet of best quality and approved make with 100mm "P" or "S" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia,double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement,cement for packing,spun yarn,teak wood plugs,brass screws,etc., including supplying and fixing 10 lit capacity PVC/12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets.Complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using indian adopter joint including all internal fittings .(The EWC and flushing tank with all accessories should be got approved by tyhe executive engineer before use on works) with 10 lit capacity flushing tank with all internal dualflush fittings with normal seat cover wall fitting

Supplying and fixing in position best quality approved make white glazed earthenware wash hand basin of size 550 X 400 mm with a pair of cast iron brackets, including cost of 15mm diametre brass chromium plated piller tape,32 mm diametre C.P. Waste union, 32 mm diametre P.V.C. waste pipe with rubber plug and chain, 15mm diametre G.M.wheel valve, 15mm dia brass nipple, 15mm dia nylon connections etc., including fixing the wash hand basin in the wall in position with a pair of C.I. brackets with teak wood plugs and screws and giving necessary water supply connection and paintiung the brackets with two coats of paint over a primimg coat of anticorrosive paint including testing for leackage etc., complete complying with standard specifications

Supply and fixing in position of best Indian make white / colour glazed earthernware lipped mouth flat back urinal of best quality and approved make of size 430mm x 260mm x 350mm with GI pipe, 32mm dia bell mouth PVC connection and waste pipe, 15mm dia GI pipe of required length, 15mm dia GM wheel valve, 15mm dia brass nipple 2 Nos., and fixing the urinals in position with necessary TW plugs, clamps, screws, etc., including dismantling masnory and re-doing the same to the original condition, etc., including painting the pipe with two coats of best quality approved synthetic enamel paint over one coat of red oxide primer and checked without any leakage etc. complete complying with standard specifications and as directed by the departmental officers. (The urinal should be got approved by the Executive Engineer before use on works.)

Providing and fixing Hand Spray / with Button control (Health faucet) with flow Rate of 3.78 LPM at 3 Bar pressure including flexible hose 1m/1.2m long connection and holder for hand spray ,making good the same, complete.of Engineer-in-charge.

Suppling and fixing in position 15mm.diameter brass / C.P screw down tap / pillar tap (heavy duty) of approved make conforming to I.S.specifications and quality including cost of shellac, thread etc.complying with standard specifications and including cutting and threading wherever necessary

Supplying and fixing in position Brass C.P.Shower rose Shower Rose - 100mm dia & CP Wall Mixture Tap 3 in 1 system with Hand Showers of approved make confirming to IS specifications and qulity including cost of Shellac thread etc. complying with standard specification.

Supplying and fixing best approved quality Brass C.P / Al anodised Towel rail 600mm. long and 20mm Diameter with brackets of same material including cost of Teak-Wood plugs and C.P.Screws etc., complete complying with standard specifications

Supplying and fixing in position C.P. Soap tray of size 150 x 100mm including cost of teak wood plug and C.P. screws. etc. complete complying with standard specification.

Supplying and fixing in position Stainless Stee Sink of size 600mm x 450mm x 200mm including cost of teak wood plug and C.P. screws. etc. complete complying with standard specification.

Supplying and fixing in position SS Swan Neck Tap suitable with kitchen sink etc. complete complying with standard specification.

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks)

Supply and fixing of PVC. Nahini / Floor Trap with stainless Steel Gratings- 100 mm x 75 mm including all charges etc, complete as per standard specification.

P.V.C. Pipes (10Kg/SqCm) Supplying laying and jointing P.V.C pipes (10Kg/SqCm) of approved quality and best variety conforming to I.S.S & with I.S.I mark, of the following sizes including cutting , Fixing to PVC specials using Adhesive but excluding cost of such specials and fixing to wall with necessary teak - Wood Plugs,PVC Clamps and screws,making holes on the wall or drilling holes in roof and making good the dismantled portions to original condition with necessary brick work and plastering wherever necessary with necessary scaffolding charges.

20mm dia pipe

25mm dia pipe

32mm dia pipe

Supplying PVC Specials (with working pressure 10 kg. / sq.cm.) in water supply arrangements (both in internal and external water supply arrangements

Coupler

20mm dia

25mm dia

32mm dia

Elbow

20mm dia

25mm dia

32mm dia

20mm dia

25mm dia

32mm dia

20mm dia

25mm dia

32mm dia

End Cap

20mm dia

25mm dia

32mm dia

Reducer

20mm dia

25mm dia

32mm dia

Reducer Tee

20mm dia

25mm dia

32mm dia

Reducer Elbow

20mm dia

25mm dia

32mm dia

Jet Nipple

25mm dia

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work.

25mm dia

40mm dia

50mm dia

65mm dia

Supplying and fixing of approved make of GM Non return valve, suitable for both horizontal & vertical application conforming to BS 1982 tested to a pressure of 15 Kg/sqcm. Including rubber gasket, flanges, union, nuts, bolts, washers & painting complete as required, shutter of brass/SS304 conforming to ASTM B159. as directed by Engineer-Incharge.

65mm dia

50mm dia

Supplying laying and jointing P.V.C pipes soil/ waste pipes (6Kg/SqCm) of approved quality and best variety conforming to I.S.S & with I.S.I mark, of the following sizes including cutting , Fixing to PVC specials using Adhesive but excluding cost of such specials and fixing to wall with necessary teak - Wood Plugs,PVC Clamps and screws,making holes on the wall or drilling holes in roof and making good the dismantled portions to original condition with necessary brick work and plastering wherever necessary with necessary scaffolding charges.

110mm dia pipe

75mm dia pipe

40mm dia pipe

50mm dia pipe

Supplying PVC Specials P.V.C pipes soil/ waste pipes (with working pressure 6 kg. / sq.cm.) in water supply arrangements (both in internal and external drainage arrangements

Elbow

110mm dia

75mm dia

50mm dia

110mm dia

75mm dia

50mm dia

110mm dia

75mm dia

50mm dia

110mm dia

75mm dia

Reducer

110mm x 75mm

Supplying and fixing in position 150 x 100mm "P" or "S" stoneware gully trap 'A' grade with CI double gratings of size 150 x 150mm and 230 x 230mm at bottom and top respectively with necessary earth work excavation laid over a bed of brick jelly cement concrete 1:3:6 (One cement, Three Crushed stone sand and Six broken brick jelly) 150mm thick using 40mm size broken brick jelly including necessary brick work and plastering including dismantling masonry wherever necessary and re-doing the damaged portions to the original conditions using cement concrete 1:3:6 using 20mm stone jelly for fixing the gully trap and giving connections to stoneware sewer line etc., complete complying with standard specifications. [Earth work excavation, brick work, plastering shall be measured and paid separately]. The stoneware gully trap should be got approved by the Executive Engineer before use on works.

Construction of sewer chambers of internal dimension of 600x600mm depth upto 1 Mtr depth with brick masonry in cement mortor 1:5 thickness of masonry 225 mm, 1:3:6 cement concrete foundation 150 mm thick over 150 mm sand bed, channelling in 1:2:4 cement concrete, plastering in 1:3 cement mortor for internal and external surface finished with floating coat of neat cement. SFRC make Heavy duty manhole cover (600x600) with frame,CI step 300mm.and fixed over 100 mm P.C.C. making arrangement for manhole cover seating, necessary exacavation and backfilling.(Observed OD)

Construction of sewer chambers of internal dimension of 750x750mm depth upto 1 Mtr depth with brick masonry in cement mortor 1:5 thickness of masonry 225 mm, 1:3:6 cement concrete foundation 150 mm thick over 150 mm sand bed, channelling in 1:2:4 cement concrete, plastering in 1:3 cement mortor for internal and external surface finished with floating coat of neat cement. SFRC make Heavy duty manhole cover (600x600) with frame,CI step 300mm.and fixed over 100 mm P.C.C. making arrangement for manhole cover seating, necessary exacavation and backfilling.(Observed OD)

Construction of sewer chambers of internal dimension of 900x900mm depth upto 1.2 Mtr depth with brick masonry in cement mortor 1:5 thickness of masonry 225 mm, 1:3:6 cement concrete foundation 150 mm thick over 150 mm sand bed, channelling in 1:2:4 cement concrete, plastering in 1:3 cement mortor for internal and external surface finished with floating coat of neat cement. SFRC make Heavy duty manhole cover (600x600) with frame,CI step 300mm.and fixed over 100 mm P.C.C. making arrangement for manhole cover seating, necessary exacavation and backfilling.(Observed OD)

Supplying laying and jointing of UPVC Pipe (Un-Plasticized Polyvinyl Chloride)(Schedule-80) pipes complete with necessary solvent cement weldable fittings, confirming to ASTM F-441 for water supply piping in the pumping system. The pipes shall be erected plumb in the risers. Erection of the above pipe including cutting, jointing of pipes with necessary fittings, erection of the pipes plumb to vertical, clamping the pipes on to MS Hot dip galvenized clamps, pressure testing of pipes, complete.. The pipes shall be laid burried Laying work to include excavating the necessary trenches,cutting and jointing and laying the pipes in the trenches.after laying and pressure testing of pipes, the excavated earth shall be back fill and compacted any excess shall be removed from site.

65mm dia Pipe

50mm dia Pipe

40mm dia Pipe

Supplying UPVC Specials pipes (UPVC Sch-80.) in water supply arrangements (both in external Hydro Pneumatic System Pumps arrangements)

Elbow

65mm dia

50mm dia

40mm dia

65mm dia

50mm dia

40mm dia

65mm dia

50mm dia

40mm dia

Coupler

65mm dia

50mm dia

40mm dia

Supplying laying and jointing P.V.C pipes soil/ waste pipes (6Kg/SqCm) of approved quality and best variety conforming to I.S.S & with I.S.I mark, of the following sizes including cutting , Fixing to PVC specials using Adhesive but excluding cost of such specials and fixing to the pipes shall be duly laid at site, with necessary cutting & jointing of pipe with approved quality jointing lubricant. The pipes shall be fixed properly aligned and laid to slope. Before handing over, leak test shall be carried out and any defects found shall be rectified. Work shall also include necessary excavation and back filling 'with compaction etc, as directed by Engineer- Incharge (For sewer and Sullage line).

160mm dia

110mm dia

75mm dia

Supplying and fixing PVC RAIN WATER DOWNFALL PIPE of the following dia with necessary T.W.Clamps Plugs, Shoes,Bemds, other clamps, screws nails etc.,complete complying with standard specification. The rate is inclusive of cost of removable iron gratings of appropriate size. The size of Teak Wood plugs used is 150X25mm in front & 200x75mm in rear (wall side) with a depth of 160mm. The pipe is to be fixed by means of "U" clamps at the centre of pipes to be fixed.160mm dia PVC Pipe [4 Kg/SqCm]

Supplying and fixing in position best quality P.V.C rainwater burried pipe (4 kg. per sq.cm) of various sizes having ISI mark and providing leakproof joints including fixing to the chamber with P.V.Cspecials etc., and making connection to all rain water, dismandling masonry/R.C.C. works wherever necessary and making good the dismandled portion to the original condition, complying with standard specifications.

Construction of percolation well / rain water harvest pit of of required internal dimension of 1.5mtr Dia upto 2.5 Mtr depth with brick masonry in cement mortor 1:5 thickness of masonry 225 mm, 1:3:6 cement concrete foundation 150 mm thick over 150 mm sand bed, channelling in 1:2:4 cement concrete, plastering in 1:3 cement mortor for internal and external surface finished with floating coat of neat cement, With perforated RCC cover, fixed over 100 mm P.C.C, Rungs, etc. The work shall include necessary exacavation and backfilling placing 2 nos of 200mm dia slotted pie for 5mtr from the bottom of the catch pit, 25mm coarse aggregate (black pebbles) for filteration.

Supplying and fixing in position CI manhole covers with CI frames (Heavy duty) of size 60cm x 60cm of best approved quality as per standard specification etc., complete compying with standard specifications

Drilling of Borewells anywhere in TamilNadu including transportation from one place to another with in TamilNadu in alluvial soil sedimentary strata of clay and sand stone shale pennles boulders etc. By first taking a pilot bore of 140mm/150mm dia and then enlarging to required dia direct or reverse rotary mud circulation method using rotary rigs fuel, labour and drilling bentonite and water required for drilling at site.- Up to 60m depth ending below ground level. (1 Nos borewells each 153 RM).

Supply and installation of equivalent approved make,For pumping the Domestice water from bore well to OHT.Pumps shall deliver 15m3/hr @ head of 45mtr.,3.0 HP Submersible Pump with fixed speed system.1 working. of 1no.s of gate valve and 1nos of non return valves.Control panel, Three phase preventer, with dry run control provision.(Nylon Rope for Bore-well)

PASSENGER LIFTS (G+1): SS 304 Grade with 1m/sec. speed with ARD Higher End. 13 Persons Passenger Lift Car Size (2000 x 1100)Gearless Lift with Machine Room

Construction of granular sub-base by providing close graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401 .

Wiring with 2x1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires with metal box and 6A 1way modular Switch in flush with wall with suitable modular front plate cover for making good of the concealed portion for PVC concealed light point /fan point for Electronic Regulator) (4 Points Per Coil) (Anchor Roma/Equivalent)

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) ( 5 points / Coil) Lower End

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) ( 6 points / Coil) Lower End

Wiring with 3x1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires metal box and 6A 2way modular Switch in flush with wall with suitable modular front plate cover for making good of the concealed portion for PVC concealed stair case light point (Anchor Roma/Equivalent)

Supply and fixing of single box type 4'20 W LED fitting with TW round blocks on wall or celling with PVC unsheathed Copper leads from terminals to the fitting.

Supply and fixing of 9 W LED bulb for BH point

Supply and fixing of WT bulk head fitting with guard suitable for 9W LED Bulb with electrical connection.

supply and fixing of 30W LED street light fitting with LED (Lower end) with 25mm dia. GI pipe (class B) with 1 no.25mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting .

Supply and fixing of 24W LED 2x2 square type Recessed fitting with LED (Lower end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting.

Supply and fixing of 1200mm (48") AC ceiling fan complete with stepped electronic 300W regulator with 1 meter down rod on the existing clamp

Supply and fixing of 300mm (12") sweep (light duty) AC exhaust fan complete without provision of hole in the wall

Supply and fixing of louvers shutters arrangements for 300mm (12") sweep (light duty) AC exhaust fan

Supply and fixing of 1 no.6/16 A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box ( GI ) in flush with wall with connections. Lower End

Supply and fixing 1000W automatic electric water heater of 25 liters capacity suitable for 230V 50 c/s AC supply on suitable MS clamps with 3 core flx wire, but without plumbing work.

Supply and fixing of 3 nos.6A two module 5 pin socket , 3 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box ( GI ) in flush with wall with connections. Lower End

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 40A DP MCB Isolator as incoming and 6 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and fixing of 4 way Horizontal Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 40A 4P MCB Isolator as incoming and 12 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 100A 4P MCB isolater switch as incoming and 4 nos. 63A TP MCB as outgoing in flush with wall with earth connection only. Lower End

Supply and Run of 2 of 2.5 sq.mm. (36/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection of 2.5 sq.mm wire and making good of the concealed portion with suitable colour.

Supply and run of 2 of 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade insuitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 4 sq.mm wire andmaking good of the concealed portion with suitable colour

Supply and run of 4 of 6 sq.mm. (84 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 6 sq.mm. wire andmaking good of the concealed portion with suitable colour

Supply and fixing of 1 no.6A two module 5 pin socket , 1 no. 6A one module switch with module cover plate (plastic) on suitable module concealed Box ( GI ) in flush with wall with connections. Lower End

Supply and fixing of 450MM 18" Almonard Walla Fan on wall with connection.

Supply and fixing of Havells JETAALBA - FLOOD LIGHT -70W LED Fitting with Necessary Wall Grouting clamps with Fixing bolts on ceilling with PVC unsheathed Copper leads from terminals to the fitting.

Supply and fixing of Havells LED Low Bay 50W Fitting with MS Clamp Set with Bolt and Nut and to be suspended with SS Chain 32 mm width with End Hooks with PVC unsheathead Copper leads from terminals to the fitting.

Supply and fixing of 20A DP Plug and Socket in sheet enclosure with 32A DP MCB in flush with wall with earth connection (For AC Plug)

Supply and fixing Anchor Roma make 32 A Key ring tag switch (Poly carbonate 32A switch) in flush with wall

Supply, erection,testing and commissioning of 1.5 Ton (4500 K.Cal/Hr) ABS Plastic split type Air conditioner confirming to is : 1391(part 2) 1992 Amdt No.1 to 2 fitted with Rotory compressor operating Refrigerant R.22/ Non CFC suitable for wall mounting for operating on 230 voltrs, 50 HZ single phase AC supply with star rating of 5 as per BEE specification and capable of performing the functions of 1) Cooling 2) De humidifying 3) Air circulating 4) filtering.

The installation works for the above split type AC units includes the followings. Mounting/fitting in door and out door units at the respective locations.(3 Star)

1. Laying Refrigerant pipe line of required length connecting both units after drilling hole/holes in the wall if required. Thickness of copper tubing shall not be less than 0.7mm. 2. Insulating the suction pipe with expanded polyethylene foam 5 mm tubing. 3. Laying 15mm dia Flexible PVC drain pipe to throw out. The condensate water being formed within Indoor unit. 4. Leakage testing the entire system with outdoor unit stand. 5. Charging Refrigerant gas in the unit. 6. Suitable electric wiring to be provided with 2.5 sqmm. PVC insulated copper wire between indoor and out door units up to 6 meters length and up to Switch within 3 meters of location of in door Unit. (Carrier/voltas) (DGS & D Rates)

Renewal by supply and installation of 4.0 KVA Electronic Automatic voltage stabilizer V-Guard Make with input voltage Range of 170 volt to 270 volt and output voltage range 200 volts to 240 volts with High and low voltage cut off and 3 minutes time delay relay with demonstration

Supply, erection,testing and commissioning of 2 Ton (6000 K.Cal/Hr) ABS Plastic split type Air conditioner confirming to is : 1391(part 2) 1992 Amdt No.1 to 2 fitted with Rotory compressor operating Refrigerant R.22/ Non CFC suitable for wall mounting for operating on 230 voltrs, 50 HZ single phase AC supply with star rating of 5 as per BEE specification and capable of performing the functions of 1) Cooling 2) De humidifying 3) Air circulating 4) filtering.

The installation works for the above split type AC units includes the followings. Mounting/fitting in door and out door units at the respective locations.(3 Star)

1. Laying Refrigerant pipe line of required length connecting both units after drilling hole/holes in the wall if required. Thickness of copper tubing shall not be less than 0.7mm. 2. Insulating the suction pipe with expanded polyethylene foam 5 mm tubing. 3. Laying 15mm dia Flexible PVC drain pipe to throw out. The condensate water being formed within Indoor unit. 4. Leakage testing the entire system with outdoor unit stand. 5. Charging Refrigerant gas in the unit. 6. Suitable electric wiring to be provided with 2.5 sqmm. PVC insulated copper wire between indoor and out door units up to 6 meters length and up to Switch within 3 meters of location of in door Unit. (Carrier/voltas) (DGS & D Rates)

Renewal by supply and installation of 5.0 KVA Electronic Automatic voltage stabilizer V-Guard Make with input voltage Range of 170 volt to 270 volt and output voltage range 200 volts to 240 volts with High and low voltage cut off and 3 minutes time delay relay with demonstration

Supply and fixing of Anchor Roma Louvres White Foot Lamp with 4 Module Box & Tresa Cover, 22025 in Grabtree 4Module Box with necessary connection.

Supply and Run of 4 of 10 sq.mm. (140/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 10 sq.mm copper wire with painting of suitable colour.

Supply and run of 2 of 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in rigid pipe concealed in wall and ceiling with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour

Supply and fixing of Douple pole sheet steel enclosure with 1 no 30 A DP isolator on wall and necessary connection for street light control

supply and fixing of 65 mm dia. (2 -1/2") GI pipe (class B) of 6 metre length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom with concreting with construction of masonary pedestal with suitable SMC box with door arrangement to house 6A SP MCB switch, 2/4 way connector on suitable hylem sheet and supply and fixing of 30W LED street light fitting with LED (Lower end) with 1 metre 32mm dia. GI pipe (class B) Complete with suitable MS clamps for LED steet light fitting and SMC box with PVC unsheathed copper leads from SMC box to fitting and with painting of suitable colour

Supply and Laying of 2 x 10 sq.mm. PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good.

Supply and clarnping of 2 x 10 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps

Supply and fixing of brass cable gland for 2 x 10 sq.mm. PVC armoured LTUG cable with earth connection.

Supply and fixing of 8 way vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 100 A 4P MCB Isolator as incoming and 6 nos.63A TP MCB and 2 Nos 32A TP MCB as outgoing in flush with wall with earth connection only. Lower End

Supply and fixing of AC / DC 76mm buzzer / call bell suitable for 230 volts 50 c/s single phase AC supply on suitable TW board with push switch

Supply and run of 2 of 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in rigid pipe concealed in wall and ceiling and making good of the concealed portion with suitable colour

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry

Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection

Supply of 1 No 125 KVA Diesel Generator set of 0.8 P.F Three Phase 415 / 420 Volts, 50c/s, 1500 RPM as detailed below (CPCB IV Norms and BIS Specification. . A.ENGINE Water cooled diesel engine suitable for Generator application with a shaft output of 310 BHP 1500 RPM under NTP conditions as per BSS 5514 / IS 10000. The Engine shall comprise the following standard scope of supply: (Make Kirloskar Green / Cummins)

1.Dry Type Air Cleaner 2.Expansion bellow 3.Radiator, Radiator fan and mounting 4.Air to air charge 5.Exhaust Gas turbo charger 6.Lube oil cooler and Lube oil filter 7.Fuel filter (pre and Micro) 8.In-line Mono - block fuel injection pump with governor and fuel feed pump. 9.Electronic governor 10.12 V Battery charging alternator 11. 12V Volt electric starter motor 12. Engine test Certificate 13. Residential Muffler 14. Fly Wheel with Housing 15. Exhaust silencer

SAFETY SYSTEM OF ENGINE The Engine shall trip for the following conditions with visual alarm device 1. Low lubricating Oil Pressure 2. High water temperature 3. Vee-belt failure and over spee The following visual indicator should also be provide Low Battery Indication. The Engine should be capable of providing 10% over load for one hour for every 11 hours continuous running at full load

B.ALTERNATOR: Alternator capacity of 45KVA / 50KW, AC 3 phase, 50HZ, 415Volts, 0.8 P.F 4 wire self excited, self regulated designed to run at 1500 RPM under NTS conditions conforming to BS 5514 / ISO 3046/ISO 8528 (part-II) 1992 to be coupled directly to the Diesel Engine and test cerfiticate (Make Kirloskar Green / Cummins)

C) AMF CONTROL PANEL: The AMF control panel (cubical) should be fabricated with vermin proof and dust proof best quality sheet steel and floor mounted with removable rear panels and hinged front doors with enamel painted and incorporating the following with suitable provision for connecting incoming and outgoing leads have been made on the control panel complete set.

21) 1No signal lamp for indicating load on mains 22) 1No signal lamp for indicating load on set 23) 1No signal lamp for indicating set fails to start 24) 1No signal lamp for indicating ‘Set running’ 25) 1No signal lamp for indicating ‘Battery charger ON’ 26) 1set pilot lamps of 3Nos 27) MCCB of 125A capacity with magnetic thermal over load release, instant short circuit trip and under voltage release switch. 28) Rectangular copper bus bars (1No for each phase, neutral and earthing terminal) of adequate capacity duly colour coded with head shrinkable PVC sleeves. 29) 1No mains voltage monitor 30) Hooter/Audio alarm for indication set fails to start and for DG O/L 31) 1set timers 32) Audio and visual indication arrangements for

a) Low lubricating oil pressure b) High water temperature c) Over speed 33) 1No Earth fault relay 34) Isolator to Isolate the neutral

1. The control panel should be complete with necessary fuses, cables, labels, other accessories with neutral isolation arrangements. 2. The engine should trip for the following conditions. a) Low lubricating oil pressure b) High water temperature c) Over speed 3.Supply and fitment of Auto mains failure panel 1EB service with 125Amps switch and contactors SUF control relays timers etc.

D. ACOUSTIC ENCLOSURE Acoustic enclosure shall be powder coated and fabricated of 16 SWG CRCA MS sheet. The Silent canopy shall be of nut bolt type construction. Critical processes of punching are done on CNC machines to maintain dimensional accuracy of hole within 0.1mm . Power coating done after seven - tank surface preparation process of sheet metal. Canopy panel and doors shall have inside lining of FIRE RETARDANT 64 kg/ m density Mineral wool of 100mm thickness as acoustic material. Four hinged doors shall be provided to canopy. The average sound level at 1 Mt Distance shall be less than 75 dB average or as per CPCB norms

E. BASE FRAME Base frame should be fabricated in sheet metal. The base frame is rugged in construction and designed for mounting engine and brush less alternator closely coupled, with cross members mounted on AVM The base frame shall be proivision for mounting of acoustic enclosure on it.The supply of Gen set includes loading, unloading and transportation charges.

F. FUEL TANK 150 Ltrs. Integral Built in Fuel tank shall be fabricated out of 14SWG CRCA MS sheet and its part of base frame. It is duly painted and fitted with inlet and outlet connections and mechancial fuel gauge. Supplying and filling of Diesel to run and test the generator at full load for 8 hours

G. BATTERY 1 No 12V 150 AH Battery

h. Supply of maintenance manual books with engine and alternator Parts list. i. Supply of tools required for the Maintenance and operations of the Generator set. j. Mounting of starting batteries of 1/2" thick hylem sheet base with suitable angle iron frame work support on the floor by the side of generator set to conform to latest CEIG conditions. k. Supply and laying of annunciation cable of suitable capacity and length between engine and the control panel of the generator set / Rate for item (a) to (k))

Supply and installation of exhaust piping of sufficient length with suitable MS pipes so as to extened outside the generator room with necessary thermal insulation.

Supply of lubricating oil and first charging of starting battery and supply of 80lts diesel to run the genset for minimum of 8 hours.

Providing suitable concrete foundation with cement concrete 1:2:4 of height 5 feet with sand cushion all around the foundation and erection of generator set with proper alignment over the existing foundation.

Design, Engineering, supply, fabrication, erection, testing, commissioning and handing over of 1No 10 person capacity passenger lift Gearless with machine room (KONE / OTIS / JOHNSON) as per the following Technical specifications with free Gurantee period of one year from the date of commissioning

1. Type of lift : passenger lift 2. Capacity of lift : 10 persons capacity passenger lift 3. Speed : 1.00Meter/Sec 4. Type of Drive: specific variable voltage variable frequency V3F drive with enhanced ride comfort and leveling functions 5. No. of floors: Ground + 1 floors 6. Leveling Accuracy: High level 7. Construction of Car: 18 SWG High quality stainless steel car, powder coated stretcher impact protection 8. Position of machine: Directly above the lift well

9. No. of landing entrance: 2Nos 10. No. of car entrance: one in front only 11. Car entrance door: power operated 12. Car entrance door: Power operated center opening sliding 18 SWG stainless steel vandal proof door with provision for emergency key opening at all landings 13. Lift well : existing (as per IS) 1300mm wide x 1350mm Deep 14. Car clear opening : as required (as per IS 14665) (part I) - 2000) 2000mm Height x 1000mm Wide

21. Emergency light: Battery operated light to be provided with Automatic charging device 22. Fire Man’s switch: To be provided at ground floor 23. Minor builders work: included in the scope. 24. Scaffolding: Included in the scope 25. Sill angles and facia plates: included in the scope. 26. Steel for lift machinery: Included in the scope 27. Servicing and maintenance: Free comprehensive servicing and maintenance should be provided by lift contractor during the guarantee period of one year.

28. Automatic Rescue device: To facilitate the landing of the lift to the nearest floor at the time of power failure. This shall consist of suitable type battery system with charger, inverter, under voltage protection system etc., complete with all accessories. 29. Provision of intercom with phone: To be provided by lift contractor with one handset in the lift car and another handset in the lift machine room with telecom exchange unite with one trunk and three extension linked proton 103 matrix telecom unit and required length of single twisted pair with thickness of 0.5 mm to 1 mm connecting the handsets and telecom exchange unit. 30. Lift License: Preparation of Drawing, payment of charges to CEIG and insurance policies if any and obtaining CEIG safety certificate as per lift act should be done by lift contractor. 31. Floor announciator with music.

32. Special features: a. Infra red door sensor 2D with full height screen. b. Full width half height rear panel mirror. c. Tubular stainless steel hand rail in cars. d. Voltage stabilizer for circuit control. e. Stainless. Steel signal fixtures. f. Vandal proof S.S. Button with S.S. cover g. SS door frames for landing doors. h. VF door operator. i. Call Register signal j. Stainless steel facia plate for car operating panel and landing fixtures. k. On – Off switch for fan and light l. Over load warning indicator with audio announcement

33. Other standard features: Over speed governor, phase failure and phase reversal relay, T. Guide brackets for car and counter weight, rubber padding under winding unit, motor of adequate capacity, electro mechanical door locks emergency key side supporting angles, motor over load protection devices final limit switch main suspension ropes counter weights lifting joist for mounting the machineries

34. Guarantee: Gurantee for the materials and workmanship of equipments complete should be offered by lift firm for a period of not less than one year. 35. Site testing in accordance with IS 14665 should be carried out at the time of handing over. 36. Supply of operation and maintenance manual with necessary tools for operation

Supply and fixing of 32A TPN metal clad switch on suitable angle iron frame work with MS cable entry boxes with PWD earthing

Supply and clarnping of 3 1/2 x 25 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps

Supply and fixing of brass cable gland for 3 1/2 x 25 sq.mm. LTUG armoured cable with earth connection

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection

Supply, Erection, testing and commissioning of 250A capacity dust and vermin proof horizontal type cubical panel board made up of 16 SWG CRCA Sheet with supply and fixing of the following interior switches with HRC fuse links arranged horizontally with horizontal busbar chamber and cable chambers with 1. 250A FP switch disconnector fuse unit interior only with HRC fuses double break-1 Nos. 2. 100A TPN switch disconnector fuse unit interior only with HRC fuses double break-3 Nos. 3. 63A TPN switch disconnector fuse unit interior only with HRC fuses double break-6 Nos. The busbar chamber shall consist of 4 Nos 38mm x 6mm copper flat for phases and neutral and interconnection between incoming switch and buses. The 33mm x 6mm copper flat for interconnection between 63A TPN switches and 32A TPN switch to buses. 38mm x 6mm copper flat buses shall be mounted on SMC busbar insulator at proper and sufficient interval as per IE rules. The busbar chamber shall be segregated from the adjacent chamber. The heat shrinkable sleeves shall be provided for busbar with colour code. The 25mm x 3mm copper flat for double earth connection for all incoming and outgoing switches are to be provided in this panel.

The panel shall have powder coated painting of approved colours, approved by the department officers. The danger board shall be fixed at front of panel board. The panel shall be mounted on MS base channel provided all round at the bottom of the panel. The whole arrangements shall be erected on a Masonary pedestal to be constructed with suitable foundation with bolts and nuts such that the lowest SDF unit fuse handle is at a height of 0.75m from the ground level. (note: All SDF unit shall be of L&T / Siemens make).

Supply and Fixing of 200A 3 Phase LTCT size (3'x2.5'x1') 3 Compartment Panel comprising 200A, 500V Fuse Unit and Neutral Link and 200/5A CT for Meter reading in a Separate Compartment with Busbar Arrangement for connection of the Power Cables on suitable Angle iron Frame work with necessary Connection.

Supply and fixing of 250 A Three phase 500V 4 Pole Change over Switch on suitable angle iron frame work with MS cable entry boxes with earth connection only.

Supply and fixng of TNEB meter board suitable for 3 phase 200A service connection made up of suitable angle iron frame work of size 3 feet x 2 feet using angle iron of size 1-1/2" x 1-1/2" x 1/4" rigidly fixed on wall covered with hylem sheet of size 3 feet x 2 feet of 12mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos. 200A fuse units (500V), 1 No. neutral link, copper earth flat of size 1" x 1/4" with inter connection of EB meter to fuse units by 19/16 PVC insulated copper wire with earth connection complete

Supply and Laying of 31/2 x 120 sq.mm. PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good.

Supply and clarnping of 3-1/2 x 120 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps

Supply and fixing of brass cable gland for 3-1/2 x 120 sq.mm. PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 3-1/2 x 120 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc., with electrical connection complete

Sub total

KARTHIKEYAN ELECTRICALS (BID ID -1238936)