REPAIRS TO COMPOUND WALL FENCING AND WELCOME MAINTENANCE INCL CERTAIN OTHER B/R REPAIRS TO BLDG UNDER AGE B/R DIGLIPUR OF GE (S) DIGLIPUR

Amount

Demolition of brickwork or stone/ boulder masonry or PCC block masonry, built in cement mortar including all quoins, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles and removal of debris to a distance exceeding 500 mts and depositing where directed.

Demolition of reinforced cement concrete as roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work and facilitate to cut reinforcement and removal of debris to a distance exceeding 500 mtrs and depositing where directed.

Taking down cement plaster on brick or stone walls, concrete surfaces etc. including raking out joints, hacking for key, scrubbing down with water, etc. and removal of debris to a distance exceeding 500 mtrs and depositing where directed.

Dismantling posts or struts (wood, steel or RCC) any section of posts embedded in concrete, brick work, masonry, etc. including taking out embedded portion and making good disturbed ground complete all as specified and as directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and as directed.

Demolition of cement concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) and removal of debris to a distance exceeding 500 mtrs and depositing where directed.

M&L Pre-cast cement concrete Type C1, 1:3:6 (using 20mm graded crushed granite stone aggregate), block masonry with solid blocks, exceeding 10 cm in width and setting in cement mortar 1:4 complete all as specified and as directed.

M&L for rendering 15mm thick on fair faces of brick/ concrete surfaces in two layers of 10 mm thick plastering in CM 1:6 as under coat and 5 mm thick plastering in CM 1:4 as finishing coat, finished the surface even and smooth (without using extra cement) complete all as specified and as directed.

M&L for preparing newly plastered surfaces of walls and applying two coats of cement based paint over a coat of primer complete all as specified and as directed.

M&L PCC Type B0, 1:2:4 (using 12.5mm graded granite stone aggregate) as in copings, kneelers, apex stones, bed plates, levelling course, kerbs water troughs and the like including use of formwork, weathering, slightly rounded or chamfered angles and throating, finished even and smooth without using extra cement complete all as specified.

M&L for high yield strength deformed TMT steel bars 10 mm dia and over as in reinforcement for concrete, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for high yield strength deformed TMT steel bars 6 mm to 8 mm dia as in reinforcement for concrete, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for RCC M-30 design mix (using 20mm graded granite stone aggregate) as foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed.

M&L for RCC M-30 design mix (using 20mm graded granite stone aggregate) as walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses complete all as specified and as directed.

M&L for providing steel formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter, for flat rough finished surfaces of concrete all as specified.

M&L for providing steel formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter, for flat rough finished surfaces of concrete all as specified.

Excavating in trenches, not exceeding 1.50 mtr wide and not exceeding 1.50 mtr in depth for foundation etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 sqm on plan and getting out in soft/ loose soil complete all as specified and as directed.

Removing excavated soil material not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soft/ loose soil complete all as specified and as directed.

S&F rolled mild steel in joist channel angles or tee sections fixed as in main and cross beams purlins, rails and fastenings and heavy bracket framing (beam, tee angle channel or flat sections) including distance pieces, cleats etc conforming to Fe-410-W (Gde-E-250) quality-B complete all as specified and as directed.

S&F mild steel work for hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed.

M&L for preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified.

M&L for PCC Type C2, 1:3:6 (using 40mm graded granite stone aggregate) as in walls or retaining walls, any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases) complete all as specified and as directed.

S&F for galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) including taking down old existing steel barbed wire complete all as specified and as directed.

M&L for restraining, resecuring including making good of existing barbed wire fencing including tying at crossings with galvanised mild steel wire, staples or steel pins etc complete all as specified and as directed.

M&L for 4mm dia plain mild steel wire, galvanised class 3, in fencing/ cloth line including straining and fixing to wood, concrete or steel posts and/ or to straining bolts, including securing with and provision of galvanised iron tying wire, galvanised iron staples or steel pins, etc. as directed (each line of wire to be measured) including taking down old existing galvanised mild steel wire complete all as specified and as directed.

S&F punched type concertina coil of 610 mm dia (5 spiral per running metre) made from 2.50 mm dia high tensile spring galvanised steel wire of tensile 1500 Mpa with razor shaped blades of 0.50 mm thick, 10 mm length and 12 mm width, at 25 mm spacing centre to centre including taking down old existing concertina coil complete all as specified and directed.

S&F 1mm thick PVC coated chain link fencing wire mesh of size 75 mm x 75 mm, made of 4 mm dia MS galvanised wire, to any type of standards, rails, straining bolts, etc including provision of GI wire binding, including dismantling old fencing wire mesh, any type complete all as specified and directed.

S&F for mild steel work of framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290 Gde-E-165 complete all as specified and as directed.

Taking up or down 15mm bore steel tubing and connections, including cleaning for re-fixing or removal of store complete all as specified and as directed.

Taking up or down 20mm bore steel tubing and connections, including cleaning for re-fixing or removal of store complete all as specified and as directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and as directed.

Taking down chowkat or frames with shutters (without taking off shutters from the frames n. exc 1.5 Sqm each complete all as specified and as directed.

Taking down chowkat or frames with shutters (without taking off shutters from the frames exc 1.5 Sqm and n.exc 4.0 Sqm each complete all as specified and as directed.

M & L preparation of old decorated surfaces of walls plastered or unplastered including removing by brooming down all dust, dirt and all loose scales by steel wire brushing, scrapping down smoke, soots, moulds, moss and efflorescent salts and trading oil and greasy spots etc and applying one coat of white wash to walls comlpete all as specified and directed by Engineer-In-Charge.

M & L preparation of old decorated surfaces of ceiling plastered or unplastered including removing by brooming down all dust, dirt and all loose scales by steel wire brushing, scrapping down smoke, soots, moulds, moss and efflorescent salts and trading oil and greasy spots etc and applying one coat of white wash to ceiling comlpete all as specified and directed.

M & L preparation of old decorated surfaces of walls, plastered or unplastered including removing by brooming down all dust, dirt and all loose scales by steel wire brushing, scrapping down smoke, soots, moulds, moss and efflorescent salts and trading oil and greasy spots etc and applying one coat of Oil bound distemper (washable) white or tinted comlpete all as specified and directed.

M & L preparation of old decorated surfaces of ceiling plastered or unplastered including removing by brooming down all dust, dirt and all loose scales by steel wire brushing, scrapping down smoke, soots, moulds, moss and efflorescent salts and trading oil and greasy spots etc and applying one coat of Oil bound distemper (washable) white or tinted comlpete all as specified and directed.

M & L for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed.

M&L for preparation of old painted steel surface of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint over of priming red oxide on steel surface surfaces complete all as specifed

M&L for preparation of old painted wooden surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint over of pink primer complete all as specifed .

M & L 15mm thick for rendering in patches on brick work or Concrete surface in two coats 10mm thick in CM(1:6) as under coat 5mm thick CM (1:4) as finishing coat in two separate layer mixed with integral water proofing compound in finishing coat only with integral waterproofing compound @ 3% by weight of cement finished even and smooth without using extra cement complete all as specified and as directed. (Note: Water proofing compund shall be measured and paid seperately)

Supply only integral water poofing compound complete all as specified and as directed (PIDIPROOF LW)

M&L for rendering 15mm thick in Cement mortar 1:6 on fair faces of brick/concrete surfaces finished even and smooth with out using extra cement complete all as specified and as directed.

M&L for preparing newly plastered surfacesof walls and applying two coats of distemper oil emultion on walls over a coat of primer complete all as specified and as directed.

S&F in repairs 10 litres capacity, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle and flushing pipe including brackets specified complete all as specified.

Fixing only 10 litres capacity, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle and flushing pipe including brackets specified complete all as specified. (Note: Material will be issued under "Sch B" for "free for fixing")

S&F in repairs Vitreous China wash down water closet pan EWC (pedestal pattern), white (excluding flushing cistern and flush pipe) with 'P' or 'S' trap and including fixing bolts, plastic water closet seat cover, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, including connection to drain (or outgoing pipe) and to flushing pipe, etc.complete all as specified.

S&F in repairs 15mm bore dia stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and as directed.

S&F in repair 15 mm bore fancy type bip taps, CP cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

Fixing only in repair 15 mm bore fancy type bip taps, CP cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed 15 mm bore complete all as specified and directed. (Note: Material will be issued under "Sch B" for "free for fixing")

S&F in repairs 15 mm bore pillar taps, cast copper alloy,fancy type capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed.

Fixing only in repair 15 mm bore pillar taps, cast copper alloy,fancy type capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed (Note: Material will be issued under "Sch B" for "free for fixing")

S&F in repair PTMT towel rail 600mm long fixed with including chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms) complete all as specified and as directed.

M&L for 15mm nominal bore mild steel galvanised water tubing, medium grade (ISI) marked, with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified.

Fixing only in repair 15mm nominal bore mild steel galvanised water tubing, medium grade (ISI) marked, with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified. (Note: Material will be issued under "Sch B" for "free for fixing")

M&L for 20mm nominal bore mild steel galvanised water tubing, medium grade, with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified.

Fixing only in repair 20mm nominal bore mild steel galvanised water tubing, medium grade, with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified. (Note: Material will be issued under "Sch B" for "free for fixing")

S&F in repair hand shower (Health Faucet) with 1.25 meter long easy flexible tube in chrome finish and wall hook with N.R.V (back flow preventer) complete all as specified and as directed. (Make Jaquar or equivalent ISI marked )

Fixing only in repair health faucet fixing in pipe etc. complete (Note: Material will be issued under "Sch B" for "free for fixing")

S&F in repair plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminium hanging device complete all as specified.

Fixing only in repair of plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminium hanging device complete all as specified. (Note: Material will be issued under "Sch B" for "free for fixing")

S&F in repair Vitreous China wash hand basin, white, flat back, size 550x400mm excluding taps, chain and plug and porcelain stopper but including waste pipe, mild steel/ CI brackets and cutting for and pinning in ends of brackets or erecting stand complete all as specified.

Fixing only in repairs Chromium plated shower roses with or without swivel joints,any size, including fixing to steel pipeor union complete all as specified and as directed. (Note: Material will be issued under "Sch B" for "free for fixing")

Fixing only in repair chromium plated as curtain rod 20 mm dia with fixing brackets,stops,roller etc complete all as specified and as directed (Note: Material will be issued under "Sch B" for "free for fixing")

Fixing only bathroom mirror cabinet complete all as specified and as directed. (Note: Material will be issued under "Sch B" for "free for fixing")

S&F rubber beading suitable for fixing at bottom side of the door shutter to avoid the entry of insects fixed with scres or nails with adhesive complete all as specified

S&F for sheet glass, 4.0mm thick ordinary quality and glazing with oil putty in square not exc 0.5 sq. m in each pane complete all as specified and as directed.

S&F for sheet glass, 4.0mm thick ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane complete all as specified and as directed.

M&L for 2nd class hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed.

S&F 35mm thick Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and as directed.

S&F 40mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the framriming/tack coat with bituminous primer at 10 kg per 10 sq metre complete all as specified and as directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and as directed.

S&F for 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

S&F in repair 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

S&F 150mm long aluminium handles, cast type anodisd and fixed complete all as specified and as directed.

S&F 100mm long aluminium handles, cast type anodisd

S&F 100mm long Extruded aluminium alloy handles, fabricated type, anodised and fixed complete all as specified and as directed.

S&F 150mm long aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed.

S&F 100mm long aluminium anodised, barrel tower bolts of extruded section and fixed

S& F 100 mm size stainless steel butt hinges,extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed,type B-21 complete all as specified and as directed.

M&L for preparation of new wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over of pink primer complete all as specifed .

S & F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed.

S&F 18mm thick Prelaminated particle board, exterior grade, prelaminated both sides with decorative choice laminations., fixed with screws to timber frame work complete all as specified and as directed.

S & F in repair continuous (piano) hinges, mild steel, bright finish or electrogalvanised of 30mm width complete all as specified and as directed.

S&F in repairs 75mm Hasp and staple, aluminium anodised, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified and as directed.

S&F in repair stainless steel magnet lock for cupboard including fixing screws complete all as specified and as directed.

S&F in repairs Aluminium alloy wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and as directed.

MOHAMMED SAFIQUE

Kakolil Trade Agencies

Binod Hawlader