REPAIR/REPLACEMENT OF EXTERNAL WATER SUPPLY, VARIOUS PUMP SETS ALONGWITH CONNECTED ALLIED SERVICES AT ZONE I AND II AT DINJAN MIL STN UNDER GE DINJAN

Amount

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil complete all as specified and as directed.

Excavation in trenches n.exc 1.5 m wide and n.exc 1.5 m in depth for foundation taking out/laying of pipe line etc and getting out in soft/loose soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm as in soft/loose soil complete all as specified and as directed.

Removing excavated material not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and as directed.

Taking up 150 mm bore cast iron pipes/160 mm PPR pipes (including all fittings) with spigot and socket end and lead joints including burning out lead joints and recovering lead and keeping serviceable pipes in safe custody for re-use in the work and complete all as specified and as directed by the Engineer-in-Charge. Note : Excavation and earth work shall be measured and paid seperately)

All as per item No. 05 here-in-before but for 100 mm bore/110 mm PPR pipe.

All as per item No. 05 here-in-before but for 80 mm bore/90 mm PPR pipe.

M&L for 150 mm bore, cast iron pipes with flanged ends, centrifu-gally cast, class 'B', in any length laid in trenches complete all as specified and as directed by the Engr-in-charge.

M&L for 100 mm bore, cast iron pipes with flanged ends, centrifu-gally cast, class 'B', in any length laid in trenches complete all as specified and as directed by the Engr-in-charge.

M&L for 80 mm bore, cast iron pipes with flanged ends, centrifu-gally cast, class 'B', in any length laid in trenches complete all as specified and as directed by the Engr-in-charge. Note for Serial No. 8, 9 and 10 : Excavation and earth work shall be measured and paid separately under relevant items.

Laying only in trenches, serviceable 150 mm bore cast iron pipes with spigot and socket ends of any type and of any class including cleaning of old pipes and transportation of pipes from one site to another work site as required complete all as specified and as directed by the Engineer-in-Charge.

All as per ser item No. 11 here-in-before but 100 mm bore.

All as per ser item No. 11 here-in-before but 80 mm bore. Note for item Nos 11, 12 & 13 : (a) Jointing, excavation and earth work shall be measured and paid seperately. (b) Serviceable pipes shall be obtained from item No. 5, 6 and 7 here-in-before.

S&F for 200mm bore, cast iron sluice valve both end flanged, class PN 1.6 conforming to IS 14846 : 2000 with iron wheel head and stainless steel spindle (raising type) including necessary jointing materials like nuts, bolt, washer & rubber/fiber board gasket including taking out old sluice valve complete all as specified and as directed. Make :Kalpana/Venus/Upadhya/Zoloto.

S&F for 150mm bore, cast iron sluice valve both end flanged, class PN 1.6 conforming to IS 14846 : 2000 with iron wheel head and stainless steel spindle (raising type) including necessary jointing materials like nuts, bolt, washer & rubber/fiber board gasket including taking up/down old sluice valve complete all as specified and as directed. Make :Kalpana/Venus/Upadhya/Zoloto.

S&F for 100mm bore, cast iron sluice valve both end flanged, class PN 1.6 conforming to IS 14846 : 2000 with iron wheel head and stainless steel spindle (raising type) including necessary jointing materials like nuts, bolt, washer & rubber/fiber board gasket including taking out old sluice valve complete all as specified and as directed. Make :Kalpana/Venus/Upadhya/Zoloto.

S&F for 80mm bore, cast iron sluice valve both end flanged, class PN 1.6 conforming to IS 14846 : 2000 with iron wheel head and stainless steel spindle (raising type) including necessary jointing materials like nuts, bolt, washer & rubber/fiber board gasket including taking out old sluice valve complete all as specified and as directed. Make :Kalpana/Venus/Upadhya/Zoloto.

S&F for 200mm bore, cast iron butter fly valve both end flanged, class PN 1.6 conforming to IS 13095 lever operated including necessary jointing materials like nuts, bolt, washer & rubber/fiber board gasket including taking out old butter fly valve complete all as specified and as directed. Make :Kalpana/Venus/Upadhya/Zoloto.

S&F for 150mm bore, cast iron butter fly valve both end flanged, class PN 1.6 conforming to IS 13095 lever operated including necessary jointing materials like nuts, bolt, washer & rubber/fiber board gasket including taking out old butter fly valve complete all as specified and as directed. Make :Kalpana/Venus/Upadhya/Zoloto.

S&F for 100mm bore, cast iron butter fly valve both end flanged, class PN 1.6 conforming to IS 13095 lever operated including necessary jointing materials like nuts, bolt, washer & rubber/fiber board gasket including taking out old butter fly valve complete all as specified and as directed. Make :Kalpana/Venus/Upadhya/Zoloto.

S&F for 100 mm bore, cast iron non return (reflux) valve, flange type with by-pass arrangement suitable for 100 mm dia water mains conforming to IS-5312 Part-I class PN 1.6 including takind out old non return valve complete all as specified and directed. Make :Kalpana/Venus/Upadhya/Zoloto.

Taking up or down 100 mm bore steel water tubing galvanised including connections from trenches/wall/floor/ceiling etc and keeping serviceable quantity in safe custody for re-use at same site or other site complete all as specified and as directed. Note : Excavation of earth shall be paid separately under relevant item.

All as per item No. 22 here-in-before but size 80 mm bore.

All as per item No. 22 here-in-before but size 50 mm bore/63 mm PPR pipe.

All as per item No. 22 here-in-before but size 40 mm bore/50 mm PPR pipe.

All as per item No. 22 here-in-before but size 25 mm bore/32 mm PPR pipe.

All as per item No. 22 here-in-before but size 20 mm bore/25 mm PPR pipe.

All as per item No. 22 here-in-before but size 15 mm bore.

Supply, laying, connection and testing 100mm bore, Steel water tubing, galvanised, medium grade conforming to IS 1239 (Part -1):2004 with all fittings conforming to IS 1239(Part -2):2011 and fixtures complete laid in trenches etc complete all as specified and as directed.

All as per item No 29 herein before but size of pipe 80 mm bore ditto.

All as per item No 29 herein before but size of pipe 50 mm bore ditto.

All as per item No 29 herein before but size of pipe 40 mm bore ditto.

All as per item No 29 herein before but size of pipe 25 mm bore ditto.

All as per item No 29 herein before but size of pipe 20 mm bore ditto.

All as per item No 29 herein before but size of pipe 15. mm bore ditto.

Supply, laying, connection and testing 25mm bore, Steel water tubing, galvanised, medium grade with all fittings and fixtures complete fixed to walls and ceilings or laid in floors, etc complete all as specified and directed.

Supply, laying, connection and testing 20mm bore, Steel water tubing, galvanised, medium grade with all fittings and fixtures complete fixed to walls and ceilings or laid in floors, etc complete all as specified and as directed.

Supply, laying, connection and testing 15mm bore, Steel water tubing, galvanised, medium grade with all fittings and fixtures complete fixed to walls and ceilings or laid in floors, etc complete all as specified and as directed.

Supply, laying, connection and testing 20mm outer dia 3- layer PP-R (Polypropylene random co-polymer) pipes green in colour. SDR 7.4 (PN16) stablised and antimi-crobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random fittings fixture complete fix to walls Ceiling or in floors with necessary fixing arrangment clamp,screw complete all as directed.

Supply, laying, connection and testing 25mm outer dia 3- layer PP-R (Polypropylene random co-polymer) pipes green in colour. SDR 7.4 (PN16) UV stablised and antimi-crobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random fittings laid in trenches complete all as specified and as directed. Note : Excavation and earth work shall be measured and paid seperately.

Supply, laying, connection and testing 32mm outer dia 3- layer PP-R (Polypropylene random co-polymer) pipes green in colour. SDR 7.4 (PN16) stablised and antimi-crobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random fittings laid in trenches complete all as specified and directed. Note : Excavation and earth work shall be measured and paid seperately.

Supply, laying, connection and testing 50mm outer dia 3- layer PP-R (Polypropylene random co-polymer) pipes green in colour. SDR 7.4 (PN16) stablised and antimi-crobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random fittings laid in trenches complete all as specified and as directed. Note : Excavation and earth work shall be measured and paid seperately.

Supply, laying, connection and testing 63mm outer dia 3- layer PP-R (Polypropylene random co-polymer) pipes green in colour. SDR 7.4 (PN16) stablised and antimi-crobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random fittings laid in trenches complete all as specified and as directed. Note : Excavation and earth work shall be measured and paid seperately.

Supply, laying, connection and testing 90mm outer dia 3- layer PP-R (Polypropylene random co-polymer) pipes green in colour. SDR 7.4 (PN16) stablised and antimi-crobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random fittings laid in trenches complete all as specified and as directed. Note : Excavation and earth work shall be measured and paid seperately.

Supply, laying, connection and testing 110mm outer dia 3- layer PP-R (Polypropylene random co-polymer) pipes green in colour. SDR 7.4 (PN16) stablised and antimi-crobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random fittings laid in trenches complete all as specified and as directed. Note : Excavation and earth work shall be measured and paid seperately.

M&L for making connection of PP-R distribution branch with PP-R main of size upto 40mm outer dia by providing and fixing tee including cutting and making fusion joint etc. including taking down old pipes fittings complete all as specified and directed

M & L for Making connection of PP-R distribution branch with PP-R main of size 50mm to 90mm outer dia by providing and fixing tee including cutting and making fusion joint including taking down old pipes fittings etc. complete all as specified and as directed

M&L for making connection of PP-R distribution branch with PP-R main of size 110mm outer dia by providing and fixing tee including cutting and making fusion joint etc. including taking down old pipes fitting complete all as specified and as directed.

S&F for PP-R gate valves of size 25 mm outer dia (brass insert) connect to PP-R Pipe including taking down old unserviceable valve complete all as specified and as directed.

S&F for PP-R gate valves of size 32 mm outer dia (brass insert) connect to PP-R Pipe including taking down old unserviceable valve complete all as directed.

S&F for PP-R gate valves of size 40 mm outer dia (brass insert) connect to PP-R Pipe including taking down old unserviceable valve complete all as specified and as directed.

S&F PP-R gate valves of size 50 mm outer dia (brass insert) connect to PP-R Pipe including taking down old unserviceable valve complete all as specified and as directed.

S&F for CI venturimeter of size 100 mm including taking down old venturimeter complete all as specified and as directed. Make : RMCO or equivalent as approved by GE.

Taking out sluice valve of any size (200/150/100/80 mm) any type and refacing, regrinding and refixing the same at existing locations using new gasket nuts, gland packing etc complete all as specified and as directed.

Repacking stuffing box of sluice valve spindle (200/150/100/80 mm) any type including taking apart and reassembling complete all as specified and as directed.

M&L for filling gland packing to control water leakage in sluice valve and centrifugal/monoblock pump sets of any capacity any type as and when required and all as specified and as directed

S&F for 20 mm dia gate valve cast copper alloy screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union including taking down old unserviceable valve complete all as specified and as directed.

S&F for 25 mm dia gate valve cast copper alloy screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union including taking down old unserviceable valve complete all as specified and as directed.

S&F for 40 mm dia gate valve cast copper alloy screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union including taking down old unserviceable valve complete all as specified and as directed.

S&F for 50 mm dia gate valve cast copper alloy screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union including taking down old unserviceable valve complete all as specified and as directed.

S&F in repairs 15 mm bore stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and as directed.

M&L for 15mm bore Bib taps, cast copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe or brass ferrule of 15mm bore including taking down old unserviceable valve complete all as specified and as directed.

M&L for cleaning of P.S. over head reservoir of capacity 10000 gallons internally installed at different places at Dinjan, cleaning by brooming and rubbing with coir brush, taking out of mud/silt etc and cleaning again with bleaching powder to all internal surfaces, washing with water and making repair by replacing of worn out/rusted bolts, nuts and washers, making leak proof using lead and bituminus compound including necessary painting to internal surface with paint suitable for drinking water to entire satisfaction of Engr-in-Charge and writing date of cleaning etc. with paint complete all as required and as directed. Note : MS angle iron tie bar and nut, bolts and washer as required shall be mesured and paid separately.

M&L for cleaning of valve pit chamber with sluice valve, pipes etc, 150mm to 200mm dia including replacement of existing wornout/defective gland packing, nut, bolt & washer, etc with new one to make the sluice valve perfectly leak proof including marking of flow direction of inlet & outlet pipe line with necessary colour coding with one coat of synthetic enamel paint after preparation of old steel surfaces valve pit cover complete all as required and as directed

All as per item No. 64 here-in-before but for 80 mm to 100 mm dia.

M&L for brick masonry valve pit of size 90cm x 90cm x 90 cm (internal dimensions)including concrete work and construction of similar size valve pit with one brick thick wall in cement mortar 1 : 4 on 100 mm thick PCC 1:4:8 type D2 (using 40mm graded broken stone aggregate) as in foundation lean concrete, including PCC 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) as in benching and coping and 10mm thick cement plaster in CM (1:4) internally and externally upto 15cm below ground level providing valve pit cover made out of 40x40x6mm angle iron frame all-round fixed by means of 4 Nos holdfast 150mm long made out of flat iron 40x6mm embedded in PCC block (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) of size 230x200x100mm incl provn of hinges welded with angle iron frame and MS cover 3mm thck sheet, MS handle of suitable length and size welded with MS cover and suitable locking arrangement and applying two coats of synthetic enamel paint over a coat of red oxide primer including demolition of damaged valve pit complete all as specified and as directed.

M&L for preparation of old painted steel surfaces (horizontally or vertically 18 mtr height) and applying one coat of synthetic enamel paint any description over 10 cm in width or girth not otherwise described with colour as approved including temporary bamboo stagging arrangement as required complete all as specified and as directed.

Demolition of plain cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness. (below or above ground level) complete all as specified and as directed.

M&L for plain cement concrete (1:3:6) type C-1 (using 20 mm graded stone aggregate) in foundation of pipe supports/platform etc. including necessary form work complete all as specified and as directed.

M&L for rendering 10 mm thick on fair faces of concrete surfaces in cement mortar (1:4) complete all as specified and as directed.

Burning out existing lead joint in position, including removing old lead and keeping in safe custody for re-use for CI pipe 150 mm bore complete all as specified and directed.

Burning out existing lead joint in position, including removing old lead and keeping in safe custody for re-use for CI pipe 100 mm bore complete all as specified and as directed.

Burning out existing lead joint in position, including removing old lead and keeping in safe custody for re-use for CI pipe 80 mm bore complete all as specified and as directed.

M&L for run lead joint for cast iron spigot and socket pipes & fittings 150 mm bore with new lead and other jointing materials complete all as specified and as directed.

M&L for run lead joint for cast iron spigot and socket pipes & fittings 100 mm bore with new lead and other jointing materials complete all as specified and as directed.

M&L for run lead joint for cast iron spigot and socket pipes & fittings 80 mm bore with new lead and other jointing materials omplete all as specified and as directed.

S&F in repairs, 20 mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed. (Minimum weight - 210 gms) complete all as specified and as directed.

M&L for cast iron fittings for spigot and socketed pipe, such as bends (any type, radius and angle) tapers any type, (straight, bend, increasing, decreasing or double socket etc.) Tee pieces single branch. "Y" junction, double branch, cross (all sockets or socket and pigot) collars, caps and plugs etc upto 150mm bore/including taking down unserviceable CI fittings complete all as specified and as directed.

S&F in replacement of pressure gauge 100 mm dia, range 0 to 60 Kg/CM2, as per the existing make and specifications with 3/8" brass sampling cock and pressure gauge cock complete all as specified and as directed. Make : RAMCO/OMEGA/H-Guru/General Instrument.

Dismantling all parts of the submersible motor and pump set complete assembly of capacity 20 HP and checking all parts including carrying out repair and replacement of the following defective parts with new one and lowering to pump in well, commissioning and testing as required and as directed by the Engr-in-charge including execution of the following works :- (a) Rewinding of complete stator winding with best quality insulated super enamelled copper wire, water proof as per existing gauge with connected works. (b ) Repairing to motor shaft assembly complete including polishing work. (c ) Motor bush set complete - 01 No (d) Thrust bearing set complete - 01 No (e) Neck ring complete - 07 Nos (f) Gun Metal Impeller - 05 Nos (g) Casing bushing set - 01 No (h) Coupling set - 01 No (j) Coupling bush set - 01 No (k) Shaft sleeve set - 01 No

Dismantling all parts of the submersible motor & pump set complete assembly of capacity 25 HP and checking all the parts including carrying out repair and replacement of the following defective parts with new one and lowering to pump in well, commissioning & testing complete as required and directed by the Engr-in-charge including execution of the following works :- (a) Rewinding of complete stator winding with best quality insulated super enamelled copper wire, water proof as per existing gauge with connected works. (b ) Repairing to motor shaft assembly complete including polishing work. (c ) Motor bush set complete - 01 No (d) Thrust bearing set complete - 01 No (e) Neck ring complete - 07 Nos (f) Gun Metal Impeller - 05 Nos (g) Casing bushing set - 01 No (h) Coupling set - 01 No (j) Coupling bush set - 01 No (k) Shaft sleeve set - 01 No

Dismantling all parts of the submersible motor & pump set complete assembly of capacity 17.5 HP and checking all the parts including carrying out repair and replacement of the following defective parts with new one and lowering to pump in well, commissioning & testing complete as required and directed by the Engr-in-charge including execution of the following works :- (a) Rewinding of complete stator winding with best quality insulated super enamelled copper wire, water proof as per existing gauge with connected works. (b ) Repairing to motor shaft assembly complete including polishing work. ((c ) Motor bush set complete - 01 No (d) Thrust bearing set complete - 01 No (e) Neck ring complete - 07 Nos (f) Gun Metal Impeller - 05 Nos (g) Casing bushing set - 01 No (h) Coupling set - 01 No (j) Coupling bush set - 01 No (k) Shaft sleeve set - 01 No

M&L for opening of shell for taking out exhausted filter media, dismantling of worn out PVC strainers and scrapping, washing inside of filter vessel and disposal of exhausted filter media materials to a distance not exc 50m from site of iron removal filter plant and cutting using gas of 10000 Gallon per hour capacity iron removal including washing, cleaning and refilling old serviceable filter media and new filter media including closing the opening using existing cutout shell by welding, filing etc writing date of cleaning and due date with paint of specific colour and complete all as specified and as directed by Engr-in-Charge. Note: New filter media shall be paid separately as supply only under relevant item.

Supply only course sand from "Barakar river" of mesh size 1.6mmx3.2mm as in filter media suitable for use in existing filtration plant complete all as specified and as directed.

Supply only course sand from "Barakar river" of mesh size 0.8mm x 1.6mm as in filter media suitable for use in existing filtration plant complete all as specified and as directed.

Supply only cleaned and dust free filter gravel from "Barakar river" of size 3mm to 6mm including washing properly before use as in filter media suitable for use in existing filtration plant complete all as specified and as directed.

Supply only cleaned and dust free filter gravel from "Barakar river" of size 7 mm to 12mm including washing properly before use as in filter media suitable for use in existing filtration plant complete all as specified and as directed.

Supply only cleaned and dust free filter gravel from "Barakar river" of size 25mm to 38mm including washing properly before use as in filter media suitable for use in existing filtration plant complete all as specified and as directed.

Supply only manganese di-Oxide (MNO2) as in catalytic media suitable for filtration plant complete all as specified and as directed.

Suppy and fixing in repairs of new PVC strainer industrial type of 20mm dia suitable for water filtration plant of capacity 10000 GPH to match with existing one at IRP bed complete all as specified and as directed by Engr-in-Charge. Make : RMCO or equivalent.

Supply only high strength calcium white or off white free flowing granular or tablet form (Calcium Hypo Chlorite 65 to 70% chlorine content) chlorination chemical decomposing in 45 Kg plastic drum calcium based granular disinfectant more stable than chlorine gas, highly stable in sealed container, no sodium/iron/mercury/heary metal contaminations. Make : PURE CHLOR of M/S SHRI RAYALASEEMA HI-STRENGTH HYPO LTD/ M/S POTTER & WATTS CORPORATION/ M/S DECLIBACK TECHNOLOGIES PVT LTD as directed by Engr-in-Charge. Note : (a) The contractor has to produce manufactures test certificate in original indicating Batch No date of manufacturing and paid Vrs while supply of calcium based granular disinfectant. (b) The clacium based granular disinfectant shall be brought at site in sealed plastic container of appropriate capacity/size. (c) The brand of chemical shall be approved by GE before in corporation of work. Only fresh lot (not more then two months old at the time of received material) shall be supplied by the contractor. Batch No and date should be marked on every container. (d) The contractor must submit the COC(certificate of compliance) in original from manufacturers by all India authorised MES distributor for each batch of product delevered indicating including chemical analysis report by all India authorised distributor.

Supply only copper sulphate for potable water at store yard of AGE E/M of Dinjan complete all as specified and as directed. Make : RMCO or equivalent make approved by E-in-C's Branch.

Supply only ferric alum, at store yard of AGE E/M at Dinjan complete all as specified and as directed. Make : RAMCO or equivalent make approved by E-in-C's Branch.

Supply only soda ash at store yard of AGE E/M at Dinjan complete all as specified and as directed. Make : RAMCO or equivalent make approved by E-in-C's Branch.

S&F for automatic star delta motor starter of capacity up to 20 HP, relay max. range 17 to 25 Amp, 415 volts, 3 phase, including taking down the old/unserviceable star delta motor starter complete as specified and as directed. Make : Cat No. IHPASDPD* of Havells/L&T/CG.

S&F for motor protection circuit breaker Type MOG-H1M (roatary type) for rating 32 Amp, 415 volt, 3-Ph, including all accessories and including taking down the old/unserviceable motor protection circuit breaker complete as specified and as directed. Make : Cat No. ST41937OOOO of L&T/Havells/CG.

S&F in repaire, MCCB, AC, 415 Volts, 160 Amp, breaking capacity 36 KA, 4 Pole with fixed thermal & fixed magnetic setting, complete all as specified and as directed. Make : L&T/Havells/CG

S & F in repairs, MCB, TPN, 40/63Amps, 'C' Series, 10 KA capacity complete all as specified and as directed. Make : L&T/Havells/Legrand.

S&F in repairs, on load change over switch, open execution type with front operated handle, current rating 125Amps, 4 pole, 415 V, 50 Hz complete all as specified and as directed. Make : Havells/L&T/INDOASIAN.

Supply only OT solution for chlorine test of 500 ml each to AGE E/M Dinjan store yard complete all as specified and as directed. Make : RMCO or approved make by E-in-C's Branch.

S&F in repairs bridge check net of sluice valve, size 150mm bore made of brass metal, machine threaded, with all fittings and complete all as specified and as directed.

S&F in repairs bridge check net of sluice valve, size 80mm bore made of brass metal, machine threaded, with all fittings and complete all as specified and as directed.

S&F in repairs sluice valve spindle of stainless steel body machine threaded as per sample made out of stainless steel/including brass check nut suitable for 150mm sluice valve complete all as specified and as directed.

S&F in repairs sluice valve spindle of stainless steel body machine threaded as per sample made out of stainless steel/including brass check nut suitable for 100mm sluice valve complete all as specified and as directed.

S&F in repairs sluice valve spindle of stainless steel body machine threaded as per sample made out of stainless steel/including brass check nut suitable for 80mm sluice valve complete all as specified and as directed.

Taking out of 12.5 HP monoblock pump set from foundation or floor and transporting the defective pump set to civil workshop for repair and back from civil workshop after repair and transportation, re-installation, testing, commissioning same in existing position and making water supply and electric connection as per existing for smooth running of pump motors including carrying out following repair replacement :- (a) Rewinding of complete stator winding with best quality insulated super enamelled copper wire, water proof as per existing gauge with connected works. (b) Repairing to motor shaft assembly complete including polishing work. (c) Gun metal impeller.

Taking out of 7.5 HP monoblock pump set from foundation or floor and transporting the defective pump set to civil workshop for repair and back from civil workshop after repair and transportation, re-installation, testing, commissioning same in existing position and making water supply and electric connection as per existing for smooth running of pump motors complete including carrying out following repair replacement : (a) Rewinding of complete stator winding with best quality insulated super enamelled copper wire, water proof as per existing gauge with connected works. (b) Repairing to motor shaft assembly complete including polishing work. (c) Gun Metal Impeller

Taking out of 5 HP monoblock pump set from foundation or floor and transporting the defective pump set to civil workshop for repair and back from civil workshop after repair and transportation, re-installation, testing, commissioning same in existing position and making water supply and electric connection as per existing for smooth running of pump motors complete including carrying out following repair replacement :- (a) Rewinding of complete stator winding with best quality insulated super enamelled copper wire, water proof as per existing gauge with connected works. (b) Repairing to motor shaft assembly complete including polishing work. (c) Gun Metal Impeller

Taking out of 1 HP monoblock pump set from foundation or floor and transporting the defective pump set to civil workshop for repair and back from civil workshop after repair and transportation, re-installation, testing, commissioning the same in existing position and making water supply and electric connection as per existing for smooth running of pump motors complete including carrying out following repair replacement : (a) Rewinding of complete stator winding with best quality insulated super enamelled copper wire, water proof as per existing gauge with connected works. (b) Repairing to motor shaft assembly complete including polishing work. (c) Gun Metal Impeller

Attending emergency breakdown of water supply installations where directed including taking out defective submersible pump set of capacity 10 to 25 HP, column pipes from bore well and transporting the defective pump set from site to MES store yard for repair and re-lowering submersible pump set including column pipes in the existing borewell and transportation of serviceable pump set from MES store yard to borewell and install, testing, commissioning the same in existing position and making water supply and electric connection as per existing for smooth running of pump motors complete all as specified and directed by Engr-in-Charge.

M/S AUTOMOTIVE WORLD

NChetia and Sons Trading

R.D.CONSTRUCTION