Repairing work of Toilet, Kitchen, Dinning, Conference and Gym Hall corridor etc in GOs Mess at GC CRPF Hyderabad Excluding A and B Block

Amount

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead For thickness of tiles 10 mm to 25 mm

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer in-charge.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.In cement mortar

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :Of area 3 sq. metres and below

Dismantling of electrical points / conduits / switches / sockets inside the areas being demolished.(This line item is uncountable)

Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead.

Dismantling W.C. Pan of all sizes including disposal of dismantled materials including malba all complete as per directions of Engineer-in-Charge.

Dismantling dressed stone work ashlar face stone work, marble work or precast concrete work manually/ by mechanical means including stacking of serviceable and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge :

Dismantling of manhole including R.C.C. top slab, C.I. cover with frame, including stacking of useful materials near the site and disposal of unserviceable materials within 50 m lead as per direction of Engineer-in charge:

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Centering and shuttering including strutting, propping etc. and removal of form for Shelves (Cast in situ

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo-Mechanically Treated bars of grade Fe-500 or more.

Brick work with common burnt clay F.P.S. (non-modular) bricks of class designation 7.5 in foundation & plinth in cement mortar 1:4 (cement : coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in : Cement mortar 1:3 (1 cement : 3 coarse sand)

20 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. Granite stone slab of colour black, Cherry/Ruby red

Providing and laying in position ready mixed or site batched design mix cement concrete for plain cement concrete work; using coarse aggregate and fine aggregate derived from natural sources and using recycled concrete aggregate (RCA) as coarse aggregate and fine aggregate within the permissible utilization, Portland Pozzolana / Ordinary Portland/ Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the minimum specified cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement - Concrete of M15 grade with minimum cement content of 240 kg /cum. (Note: The permissible utilization of Recycled Concrete Aggregate (RCA) as coarse aggregate and fine aggregate is 25% each).

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.Size of Tile 600 x 1200 mm

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Double charge vitrified tile polished finish of size : Size of Tile 600 x 600 mm

Providing, laying and fixing 25 mm thick premium carpet flooring, comprising high-density cushioned carpet roll/tile with total system thickness of 25 mm ±2 mm, including underlay padding, adhesive, cutting, trimming and finishing, laid over prepared smooth sub-base. The work includes cleaning the surface, applying approved synthetic carpet adhesive, unrolling/placing the carpet in correct alignment, pressing and sticking firmly to achieve wrinkle-free finish, cutting around edges/corners, rolling with carpet roller, and completing all operations as per manufacturer’s specifications and as directed by the Engineer-in-Charge.

Providing and laying high-density rubber flooring in rolls made from recycled SBR granules and EPDM flecks, PU-bonded, non-porous, of density 900–1100 kg/m³, 8 mm thick (or as specified), including preparation of subfloor, applying PU primer and adhesive, joint sealing, finishing, and cleaning complete as per manufacturer’s specification and as directed by the Engineer-in-Charge. (Make: GymFloor / Rephouse / Bergo / Approved Equivalent)

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.80 mm thick C.C. paver block of M-35 grade with approved colour design and pattern.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge Glass Reinforced Gypsum (GRG) board conforming to IS: 2095- (Part 3) : 1996 (Board with BIS certification marks)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.13.85.3 With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm

Providing and applying exterior painting system over existing granite/stone masonry wall surface including thorough cleaning with wire brush and water jet, mechanical roughening/etching of the granite surface to ensure proper bonding, applying one coat of approved stone-compatible exterior primer/sealer, and finishing with two coats of premium 100% acrylic weatherproof exterior emulsion paint of approved brand and shade Matt/Glossy; including cost of materials, labour, tools & plants, consumables, scaffolding, curing, safety precautions, and all incidental charges as per manufacturer’s specifications and direction of Engineer-in-Charge. Complete

Providing and fixing VOX WCP Panel (2-groove) in Golden Oak finish, including all required accessories, corner profiles, edge trims, fasteners, adhesives, cutting, finishing, alignment, leveling and complete installation at site, as per manufacturer’s specifications and direction of Engineer-in-Charge. The rate shall include material, labour, scaffolding, wastage, transportation, handling and all incidental charges to complete the work in all respects.

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595 mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance ≥ 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32 mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8 mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-charge.With 20 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.7)

Providing and fixing complete sound-proof acoustic wall panel system (7-layer construction), consisting of base structural framework in soft/hard wood or MS channels, 12 mm plywood backing board, 50 mm thick glass wool/rock wool insulation (48–64 kg/m³), acoustic barrier board (panwood / cement-bonded particle board or equivalent), gripper frame/foam for acoustic absorption, and outer finisher layer of approved acoustic fabric (cloth), including all edge beading, corner finishing, fixing clamps, screws, adhesives, joint sealing, cutting, alignment, and installation, complete as per approved acoustic design and as directed by the Engineer-in-Charge.

Providing and fixing wooden false ceiling with border frame of 19 mm BWP-grade plywood finished with 4 mm thick decorative veneer / laminate and central luminous panel of 3 mm thick translucent white acrylic sheet (opal finish), including G.I. suspension system, aluminum support frame, necessary adhesive, hardware, and complete installation, finished smooth and clean, as directed by Engineer-in-Charge. (Excluding LED lighting arrangement).

Providing and fixing MS powder coated grid ceiling framework in bar area, including all MS members, brackets, hangers, ceiling channels, and suspenders, with alternate placement of laminate finished panels mounted on 8mm plywood backing, as per approved pattern. All materials, labour, fabrication, cutting, grooving, fixing, alignment, finishing, scaffolding, consumables, transportation, protection and cleaning etc., complete, as per drawing and as directed by the Engineer-in-Charge

Gym- Providing and fixing metal false ceiling at all heights, using factory made metal tiles of 600×1200 mm (2’×4’) module, manufactured out of 0.50 / 0.60 mm GI sheet, pre-treated and powder coated BLACK (Matt RAL-9005) with minimum 50 micron coating thickness, supported over exposed heavy duty T-Grid system, comprising mains at 1200 mm centres, cross tees at 600 / 1200 mm to form 600×1200 grid, hangers with GI wire & cleats fixed to RCC slab, perimeter wall angle of 24×24×0.5 mm powder coated black, including all brackets, fasteners, leveling, cutting, making openings for lights / sensors / diffusers (fixtures by others), complete as per manufacturer specification and direction of Engineer-in-Charge.

Mirror polishing on marble work/Granite work/stone work where ever required to give high gloss finish complete.

Providing and fixing full-height glass partition panel of width 3 ft or 4 ft (as required) and height up to 9 ft, using 10–12 mm thick toughened & Tinted safety glass with polished edges, including providing and fixing SS-304 top & bottom channels, side U-profiles, brackets, floor/wall anchors, stabilizer bar (if required), rubber gaskets, silicone sealant, screws and fittings, complete with cutting, drilling, levelling, alignment and installation. Work includes all labour, materials, scaffolding, accessories, joint finishing and making good the surfaces, complete as per approved drawing and as directed by the Engineer-in-Charge.

Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment.

Providing, fabricating, supplying and fixing decorative outdoor pergola in PVC/WPC slatted louver design, with MS hollow frame (100×100×3 mm columns, 120×60×3 mm perimeter beams, 60×40×2.5 mm rafters), top louver members of PVC/WPC 150×30 mm installed with approx. 200 mm module spacing for aesthetic pattern & controlled sun exposure, including all SS-304 fasteners, surface finishing, fixing to RCC footings, scaffolding and complete erection as per approved drawings & direction of Engineer-in-Charge.

Providing and fixing full-height (10 ft) vertical slatted pergola boundary in PVC/WPC, on MS frame, along three sides of 4.2 m pergola, comprising MS posts 75×75×3 mm at ~1.20 m c/c, MS rails 50×25×2 mm (top, mid ~1.5 m, bottom), PVC/WPC slats 150×30 mm installed vertically at approx. 200 mm module (≈50 mm clear gap) for aesthetic sun/rain exposure, including SS-304 fasteners, alignment, finishing, PCC footings 300×300×600 mm with anchor bolts, scaffolding and complete erection as per direction of Engineer-in-charge

Providing, supplying and fixing PUF Insulated Roof Panel 60 mm thick, factory made sandwich panel, comprising 0.5 mm thick pre-painted galvanised iron (PPGI) sheet on both sides, with 40 ± 2 kg/m³ density rigid polyurethane foam (PUF) core, fire retardant grade, profile sheet top finish, brand — Jindal QuadCore STRUPAN RW Roof Panel or equivalent approved make, including proper laps, side/joint seals, EPDM gasket, butyl tape, screws, fasteners, fixtures, laying to correct slope for drainage, cutting, flashing, finishing, staging, scaffolding, all complete as per manufacturer recommendations and direction of Engineer-in-Charge.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. - MS supporting structure (Sq tubes) - MS rectangular / square hollow sections (RHS/SHS) 100×50×3 mm, 80×40×3 mm MS channel ISMC 100 mm / 125 mm anchored on RCC footing or floor bolts, MS RHS 50×50×3 mm with purlins @ 1 m c/c, SS bolts, anchor bolts, welding as per IS 800

Providing and applying tack coat using bitumen emulsion conforming to IS:8887, using emulsion pressure distributer including preparing the surface & cleaning with mechanical broom With medium setting bitumen emulsion On bituminous surface @ 0.25kg/sqm

2.5 cm premix carpet surfacing with 2.25 cum and 1.12 cum of stone chippings of 13.2 mm and 11.2 mm size respectively per 100 sqm and 52 kg and 56 kg of hot bitumen per cum of stone chippings of 13.2 mm and 11.2 mm size respectively, including a tack coat with hot straight run bitumen, including consolidation with road roller of 6 to 9 tonne capacity etc. complete (tack coat to be paid for separately). With paving Asphalt grade VG - 30 with no solvent

Providing and applying 2.5 mm thick road marking strips (retro- reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications.

Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge:

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

Providing, fabricating, supplying and installing outdoor decorative Fountain System, including water storage sump at bottom (RCC / masonry pit with waterproofing), steel support structure (MS/GI frame with anti-corrosive paint/galvanized), submersible water pump of adequate capacity as per fountain jet height requirement, with required HDPE / CPVC piping, valves, strainers, nozzles, return line, flexible hoses, electrical power connection from nearest point, control wiring, testing, commissioning, and balancing of water jets, including all accessories, Civil works for pit enclosure, plumbing fittings, fixing, alignment, sealing, finishing and making the entire fountain fully operational as per approved design and direction of Engineer-in-Charge.

Providing, fabricating, supplying and installing outdoor decorative Small Fountain System, including water storage sump at bottom (RCC / masonry pit with waterproofing), steel support structure (MS/GI frame with anti-corrosive paint/galvanized), submersible water pump of adequate capacity as per fountain jet height requirement, with required HDPE / CPVC piping, valves, strainers, nozzles, return line, flexible hoses, electrical power connection from nearest point, control wiring, testing, commissioning, and balancing of water jets, including all accessories, Civil works for pit enclosure, plumbing fittings, fixing, alignment, sealing, finishing and making the entire fountain fully operational as per approved design and direction of Engineer-in-Charge.

Providing, dismantling and reconstructing granite wall/cladding, including careful removal of existing granite stones without damage, scraping and cleaning of old mortar, stacking serviceable stones within 50 m lead, disposing of unserviceable material, preparing the base surface, and re-fixing/rebuilding the wall using the same salvaged granite stones in cement mortar (1:4 or as specified), maintaining proper line, level and joints, including finishing, curing, scaffolding, all tools and plants, labour and materials required, complete as per direction of the Engineer-in-Charge.

Providing, carving, finishing and fixing stone pillar made of approved granite/sandstone as specified, machine-cut or hand-dressed, including shaping, chamfering, moulding, ornamental profiles (if required), polishing, and providing necessary base plate/footing arrangement, lifting, placing in position, plumbing, alignment and grouting. The item includes all labour, tools, lead, lift, curing, surface finishing, scaffolding, and completing the work in all respects as directed by the Engineer-in-Charge.

Providing and fixing fully automatic glass door system comprising of 12mm thick toughened glass shutter(s), complete with automatic sliding mechanism, motor, sensor, controller, top track, floor guide, patch fittings, SS hardware, power supply arrangement, EPDM gaskets, silicone sealant, alignment, testing and commissioning, including all labour, materials, tools & tackles, scaffolding, transportation and making good of surfaces, complete in all respects as per manufacturer’s specifications and as directed by Engineer-in-Charge.

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with desh fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately Second class teak wood

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately all complete as per direction of Engineer-in-charge. (Note: Butt hinges and necessary screws shall be paid separately) Second class teak wood 35 mm thick shutters

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Clerestory windows & other Frames/ Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5 mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. Frame size 50 x 100 mm

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) 35 mm thick

Providing and fixing bright finished brass butt hinges with necessary screws etc. complete 125x70x4 mm (ordinary type)

Providing and fixing bright finished brass butt hinges with necessary screws etc. complete 100x70x4 mm (ordinary type)

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete: 200x10 mm

Providing and faxing bright finished brass handles with screws etc complete - 125 mm

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete (Copper oxidised as per IS 1378) : 250x10 mm

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete (Copper oxidised as per IS 1378) 250x16 mm

Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately. Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for : (i) Sites with basic wind speed > 45 m/sec as per IS 875 – Part 3 (ii) Sites with structure height more than 20m for all wind speeds. Three track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body. Using R2 series with frame (70mm & above) x (40mm & above) & both glazed and fly screen sash (25mm & above) x (50mm & above) with zinc alloy (zamak) powder coated touch locks with hook. (Height upto 1.2 metre).

Providing and fixing cupboard shutter with 19mm thick one side decorative and other side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand including 2mm thick PVC edge banding tape with hot glue by edge bending machine etc. with auto closing spring loaded hinges (hydraulic type) etc. complete as per direction of Engineer in-charge.(Payment of providing and fixing auto closing hinges shall be paid separately)

Providing and fixing 19mm thick both side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand boxes,shelves,racks,almirah,cupboard and drawer etc. including necessary nails,screws etc. complete as per direction of Engineer-in-charge

Providing and fixing 12 mm compact laminate commercial washroom partition with SS-304 hardware, top rail, adjustable legs, door set with lock, hinges, coat hook, U-channel and complete accessories, including cutting, fixing, alignment and sealing, complete as per direction of Engineer-in-Charge.

Providing, fabricating, supplying and fixing Mild Steel (MS) gate of size approximately 15 ft in width (height as specified), made from MS hollow sections/angles/channels as per approved design, including cutting, welding, grinding, hinges, locking arrangements, stiffeners, hold-fasts, bottom guide rollers (if required), MS sheet infill/grill pattern, applying one coat of steel primer and two coats of synthetic enamel paint, erecting in position with proper alignment, including all labour, materials, tools, scaffolding, and complete finishing as directed by the Engineer-in-Charge.

Providing, fabricating and fixing branding board/signage made of stainless steel (SS-304) letters/logo fixed on ACP/metal/acrylic backing panel as approved, including laser-cut SS letters (mirror/matt finish), SS studs, spacers, supporting frame, mounting brackets, edge trims, fixing hardware, electrical wiring for LED backlit/front-lit illumination (if required), complete with cutting, welding, polishing, alignment, levelling and secure fixing to wall/structure, including all labour, materials, tools, scaffolding and finishing as per the direction of the Engineer-in-Charge.

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in charge.Made of G.I. wire of dia. 4 mm, PVC coated to achieve outer dia not less than 5 mm in required colour and shade

Supplying at site Angle iron post & strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. complete.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.

Providing, supplying and fixing retractable balcony awning made of high-quality PVC coated fabric (UV-resistant, waterproof), mounted on powder-coated aluminium/MS frame with retractable folding arms, manual/gear-operated or motorized mechanism (as specified), including brackets, wall anchors, end caps, rollers, tension arms, operating handle, guide channels, and all necessary fittings. Work includes drilling, fastening, sealing of wall penetrations, alignment, testing of smooth operation, and complete installation as per manufacturer’s specifications and direction of the Engineer-in-Charge

Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing CP Brass 32 mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing factory-made mirror with integrated LED backlight, size approximately 600×450 mm, including high-quality silver-coated mirror glass, in-built LED strip with driver, touch sensor / switch operation, edge polishing, mounting brackets, screws, wiring connection to existing electrical point, testing and commissioning, complete as per manufacturer’s specification and as directed by the Engineer-in-Charge.

Providing and fixing shower mixer valve with diverter unit of approved make, concealed/exposed type as specified, comprising hot and cold inlets, diverter mechanism for overhead and hand shower, chrome-plated brass body, operating lever, wall flange and complete internal fittings, including cutting and making good the wall, connection with inlet pipelines, leak testing, and complete installation as directed by the Engineer-in-Charge.

Providing and fixing overhead rain shower of size 200 mm diameter, made of stainless steel/brass with chrome finish, including matching shower arm (wall/ceiling mounted), flange, sealing, PTFE taping, jointing to existing diverter/shower line, testing for proper flow, ensuring level alignment and complete installation as per manufacturer’s recommendation and as directed by the Engineer-in-Charge.

Providing and fixing 8 mm thick toughened safety glass shower partition with frosted finish (full/strip as approved), including polished edges, stainless steel (SS-304) wall clamps, U-channels, corner brackets, stabilizer bar (if required), rubber gaskets, sealant, screws and accessories, complete with drilling, fixing, levelling, sealing of joints with silicone, including all labour, materials, and making good the surface complete as per direction of the Engineer-in-Charge.

Providing & Fixing Floor Trap (SS 4″ with P-trap) Stainless steel floor trap with 4″ dia, P-trap type, grating top, PVC outlet connection, complete with sealing and finishing

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 100x100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing & fixing Geyser Safety / Pressure Relief Valve (PRV) - Brass/CP PRV, ½″ or ¾″ BSP thread, pressure release 6–8 bar, with discharge pipe

Providing & Fixing Geyser Local Isolating Valve (25 mm Ball Valve) - Heavy-duty brass ball valve, full-bore type with chrome finish, PTFE seat

providing & fixing Access Panel / Service Hatch (for concealed cistern) - Powder-coated aluminum / MS hinged panel, approx. 300×300 mm, screw-fixed with frame

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 15 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 20 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 25 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 32 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work : 40 mm nominal dia Pipes

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 75 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 110 mm diameter

Providing and fixing on wall face unplasticised-PVC moulded fittings / accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5° 75 mm bend

Providing and fixing on wall face unplasticised-PVC moulded fittings / accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5° : 110 mm bend

Providing and fixing on wall face unplasticised-PVC moulded fittings / accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Shoe (Plain) 75 mm Shoe

Providing and fixing on wall face unplasticised-PVC moulded fittings / accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Shoe (Plain) 110 mm Shoe

Providing and fixing unplasticised-PVC pipe clips of approved design to unplasticised-PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 75 mm

Providing and fixing unplasticised-PVC pipe clips of approved design to unplasticised-PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25 mm nominal bore

Providing and fixing gun metal non- return valve of approved quality (screwed end) : 25 mm nominal bore Vertical

Providing, fixing, and testing foot valve with integral strainer of approved make and quality, suitable for the specified diameter of the pump suction line, made of heavy-duty brass/CI/SS as required, including non-return mechanism, perforated strainer basket, rubber disc/seat, nuts, bolts, gaskets, and necessary fittings. The item includes lowering the valve into sump, connecting to suction pipe with proper sealing, ensuring leak-proof joint, alignment, and testing of suction performance, complete as per direction of Engineer-in-Charge.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 32 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws, including excavation, refilling the earth or cutting of wall and making good the same complete wherever required : 20 mm nominal bore

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : - Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :150 mm dia. R.C.C. pipe

Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design :With 20x20 mm square bar

Supplying and fixing C.I. cover without frame for manholes 455x610 mm rectangular C.I. cover (light duty) the weight of the cover to be not less than 23 kg

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete For pipes 100 to 250 mm diameter

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required- Range of four urinal basins with 10 litre white P.V.C. automatic flushing cister

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : One urinal basin with 5 litre white P.V.C. automatic flushing cistern

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator). 8 way (4 + 24), Double door

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, Ics=100% Icu and Operational Voltage 690V etc. as required. 100 A, 16 KA,TPMCCB

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole and neutral

Supplying and fixing Cable End Box (Loose Wire Box) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 Volts, on surface/ recess, complete with testing and commissioning etc.as requiredFor 8 way, Double door TPN MCBDB

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way , Double door

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 A

Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 A

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single Pole and Neutral

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single Pole and Neutral

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single Pole and Neutral

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single Pole and Neutral

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single Pole and Neutral

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Double pole

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single Pole and Neutral

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single Pole and Neutral

Providing, fixing, testing and commissioning of Type 2 Surge Protective Device (SPD) suitable for 230/400V, 50Hz AC supply, Class II, Imax ≥ 40kA, Up ≤ 2.5kV, DIN rail mounting, conforming to IS/IEC 61643-11, complete with all accessories as required.

Earthing with copper earth plate 600 mm × 600 mm × 3 mm thick, including accessories and providing masonry enclosure with cover plate (locking arrangement) and watering pipe 2.7 m long with charcoal/coke and salt as required.

Providing and fixing copper strip 25 mm × 5 mm, in recess or on surface, for earthing connection as required.

LED Down lighter (SMD Type) (System lumen efficacy >135lm/Watt) Supplying, Installation, Testing & Commissioning of LED Recessed/surface Down lighter (Round /square/Rectangular) SMD type of following body material with PMMA and prismatic diffuser and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range - 5 0C to 40 0C, internal surge protection of 2.5 KV with Short &Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating) < 19, Flicker free, (flicker should be below 5 %), life time (LED, Driver & electrical circuitry), life time of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 Extrapolation IES TM-21-11 report, CCT 3000°K/ 4000°K /5700°K / 6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy >135 lm/Watt output. LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C). Powder coated die cast /Extruded aluminium Body including trim . 12 -15 watt

Providing and Fixing sensor based Inbuilt ambient light sensor, motion sensor based on Passive Infra Red (PIR), Surface / Concelled Lights

LED Panel light 2x2 ft. (System lumen efficacy ≥105 <120 lm/Watt) Supplying, installation, Testing & Commissioning of Panel light 2x2 ft., of following body material and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140 270 Volt, freq 50/60 hz, Operating temp range -15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection, THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating) < 19, Flicker free, (flicker should be below 5 %), life time (LED,Driver & electrical circuitry), of minimum 50000 Burning Hours with, 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K /6000°K / 6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. complete in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥105 <120 lm/Watt output . LM79 & LM80 Test report from NABL lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminum housing such that LED junction temperature shall not rise above 90°C) Powder coated die cast / Extruded aluminium Body (Thickness ≥ 1.20 mm)

Designer Lights for Bed Rooms

Led Strip Light 90 lights per meter

Profile Light with aluminium frame & Lighting Strip

Providing & Fixing Emergency Light rechargeable

Brush Less Direct Current (BLDC) Fan without Remote Supply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal( Aluminium alloy) blades, 30 cm long down rod, 2 nos. canopies,shackle kit, safety rope, copper winding, steel/Al body Power Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, suitable for operation with regulator for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 0C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC supply, Ceiling Fan compliant to IS 374:2019 fan i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required. 1200mm, service value ≥ 6.0 CM/Min/Watt, air delivery 210 CM/Min (Minimum)

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Installation, Testing and Commissioning of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Upto 450 mm sweep

Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required 5/6 A switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required 15/16 A switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required6 pin 15/16 A socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required 3 pin 5/6 A socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required 2 way 5/6 A switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 15/16 A switch

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required

Supplying and fixing Telephone / data socket (RJ11 / RJ45 modular type) on modular plate & switch box.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required. (Group C)

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Wiring for light/ power plug with 4X4 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 2 Nos. 4 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required. 2 X 6 sq. mm + 1 X 6 sq. mm earth wire

Providing and fixing of stranded copper conductor cable,typicall insulated with PVC,designed for low current,fixed, or movable wiring applications that require a high degree of bendanility

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. PVC Conduit 20 mm

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. PVC Conduit 25 mm

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. PVC Conduit 32 mm

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block includingconnections etc. as required.

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc. as required. 8 Module (125mmX125mm)

Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required.

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid 56 DELHI ANALYSIS OF RATES (E&M) 2025 and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supplying, drawing, Testing and commissioning of Cat6A UTP 4 pair, 23 AWG solid copper cable in existing conduit/ on surface, U/FTP, LSZH, Non Plenum, Horizontal (solid) Cable suitable for high speed data networking application supporting upto 10Gbps over a 100 meter channel. The 4 Unshielded Twisted Pairs (UTP) cable with color coded insulation for easy indentification should have FLAME PROPERTIES i.e. Flammability Test - IEC 60332-1, Smoke Density - IEC 61034, LSZH standards compliance: ANSI/TIA-568 C.2, ISO/IEC 11801, IEEE 802.3an, RoHS. Delay Skew should be < 45NS. The outer Cable Diameter should be 7.5 + 2 mm. Cable should have been tested and verified by UL/ ETL etc. complete as required.1 Run of cable

Providing geyser provision for 15-L storage geyser including CPVC hot/cold lines, isolation valve, inlet/outlet fittings, wall bracket support, fixing arrangements and electrical point sleeve; geyser not included, complete as directed by Engineer-in-Charge.

Providing, fixing, testing and commissioning axial-type bathroom exhaust fan of sweep 150–200 mm, air delivery 150–300 m³/hr, including mounting frame, screws, flexible connection, cutting and making good the wall/window opening, electrical connection to existing point, vibration-free installation, and complete as per manufacturer’s specification and direction of Engineer-in-Charge.

Providing and fixing flexible exhaust duct of PVC/GI material of suitable diameter (as required for exhaust fan), including clamps, supports, bends, connectors, insulation where required, cutting and sealing openings, proper routing from fan outlet to exterior discharge point, and making good surfaces, complete as directed by Engineer-in-Charge.

Providing and fixing roof/wall termination cowl or external ventilation grille with integrated bird mesh, made of PVC/SS/Aluminium as approved, including screws, anchors, edge sealing, weatherproofing, proper fixing to duct end, alignment and finishing, complete as per direction of Engineer-in-Charge.

Providing, fabricating, installing, testing and commissioning of commercial kitchen exhaust chimney/hood of width 8 ft (approx. 2438 mm) for heavy duty cooking line, made of minimum 18 gauge stainless steel grade 304 (or as per specification), full welded construction with grease-baffle filters, including internal extraction fan/blower of adequate capacity, access doors for cleaning, all necessary mounting brackets, duct connection, flashings and weatherproof roof termination, complete with electrical wiring for fan and lighting, performance test and commissioning, all as per manufacturer’s specification and direction of Engineer-in-Charge.

Providing, installing, testing and commissioning of smart electrical touch control panel for a single room comprising control of lighting, air-conditioning, television and ceiling fan. The system includes a glass-touch capacitive control panel (4-gang/6-gang as required) with WiFi/Bluetooth connectivity, voice assistant compatibility (Alexa/Google), and integrated load relays for lights, AC, TV and fan, installed in modular plate replacing conventional switches, complete with wiring back-box modifications, load relays (16 A/25 A as required), DIN rail mounting, app setup, commissioning, and handing over. The work includes all materials, labour, programming/configuration, protective covers, labeling of circuits, making good walls after installation, and full functionality as directed by the Engineer-in-Charge. (Panel to control: all room lights, AC unit, TV set, ceiling fan).

Providing, fixing, installation, testing and commissioning of cassette-type air-conditioner of approved make and capacity, including mounting of indoor cassette unit with frame/suspension rods, outdoor unit placement, refrigerant-grade copper piping (suction + liquid line) with insulation, electrical cabling between indoor and outdoor units, drain pipe connection with necessary fittings, clamps, supports, core-cutting, wall sleeves, and making good the surfaces. The item includes supply and fixing of PVC drain line, condensate piping, interconnecting communication cable, charging of refrigerant (if required), testing of cooling performance, and complete installation as per manufacturer’s specifications and direction of the Engineer-in-Charge.

M/S GALAXY SOLUTIONS (BID ID -3327570)