NIT No. : 50/PR/NBPDCL/2026 Work : Renovation and Modernization of seminar hall at Anugrah Narayan College, Patna

Demolishing R.C.C. work including stacking of steel bars and disposal of unserviceable material withing 50 metres lead:

Demolishing brick work including stacking of serviceable material and disposal of unserviceable material within 50 meters lead: In cement mortar

Desmantiling doors windows and clerestory windows (steel or wood) shutters including chowkhats, architrage, holdfasts etc. complete and stacking within 50 metres lead: of area beyond 3 sqm

Dismantling steel work in built up sections without dismembering and stacking within 50 metres lead

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.

Dismantling alumiuium/Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable surplus material and stacking of serviceable material with in 50 m lead as directed by Engineer-in-charge.

Boring, providing and installing bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement butincluding the cost of boring, with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. all complete, including removal of excavated earth with all lifts and leads (Length of pile for payment shall be measured upto bottom of pile cap).

300 mm dia piles

Earth work in excavation in foundation trenches or drains(not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m . including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

All Kinds of soil

Excavating, supplying and filling of local earth (including royalty but excluding cairriage cost) by mechanical transport upto a lead of 3km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. If local earth is available at more than 3 km lead the actual lead must be approved by compitent authority. cairraiage of material will be paid seperately and calculated after deducting initial lead.

Supplying and Filling in plinth with local sand and under floors including, watering, ramming consolidating and dressing complete.

Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level.

1:2:4(1 Cement: 2 coarse sand:4 graded stone aggregate 20 mm nominal size)

Providing and laying damp-proof Course 50 mm thick with cement concrete 1:2:4(1cement:2:2 coarse sand :4 graded stone aggregate 20mm nominal size)

Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/l,

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement-All work puto plinth level

1:1:5:3(1 cement: 1.5 coarse sand:3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in wall (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns,pillars, piers, abutments, posts and struts, etc. upt floor five level excluding cost of centring, shuttering, finishin and reinforcement.

1:1:5:3(1 cement: 1.5 coarse sand:3 graded stone aggregate 20mm nominal size)

Reinforced cement conrete work in beams,suspended floors, roofs having slope upto 15, landings,balconiec, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excludingthe cost of centring, shuttering, finishing and reinforement with 1:2:4(1 cement:2 coarse sand:4 graded stone aggregate 20 mm nominal size).

Add or deduct for providing richer or leaner mixes respectively at all floor levels.Providing M-15grade R.C.C instead of M-20 grade R.C.C.

Centring and shuttering including strutting,propping etc. and removal of form for.

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.

Brick work with bricks of class designation 100A in foundations and plinth in :

Cement mortar 1:6 (1 cement: 6 coarse sand )

Extra for Brick work in superstructure above plinth level upto floor V cum

Half brick masonry with bricks of class designation 100A in foundations and plinth in :Cement mortar 1:4 (1 cement: 4 coarse send) Extra for half Brick masonry in superstructure above pinth level upto floor V level.

15 mm cement plaster on rough side of single or half brick wall of mix.

15 mm internal cement plaster 1:6

20 mm cement plaster of mix ;

20 mm external cement plaster 1:6

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape,raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, allcomplete as per direction of Engineer-in-Charge.

With cement mortar 1:4 (1cement: 4 coarse sand)

Applying one coat of cement primer of approved brand and manufacture on wall Surface: Distemper primer

Removing dry or oil bound distemper by scrapping, sand paper and preparing the surface smooth including necessary repari scratches tec. Gmplete

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Painting with ready mixed paint of approved brand and manufacture in all shades to give an even shade:New steel work (two or more coats)

Finishing walls with textured exterior paint of required shade :

New work (Two or more coats applied @ 3.28 ltr/ 10sqm) over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications.

Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @0.75 ltr /10 sqm.

Chequered terrazo tiles 22 mm thick with marble chips of sozes upto 6mm in floors jointed with neat cement slurry mixed with pigement to match the shade of the tiles, including rubbing and polshing complete on 20 nm thick bed of cement mortar 1:4 (1 cement:4 coarse sand)

Medium shade using 50% white cement and 50% ordinary cement

Providing and laying vitrifed floor tiles in different sizes {thickness to be specified by the manufactruer) with water absorption's less than 0.08 % and conforming to IS : 15622 of approved make in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand ) including grouting the joint with white cement and matching pigments etc., complete. Size of Tile 60x60 cm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600 x 600 mm.

Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS :13755 of NITCO , ORIENT , SOMANY , KAJARIA or equivalent make in colours except white , Ivory , Grey , Fume , Red , Brown , laid on 20mm thick cement motar 1:4 (1 cement: 4 Coarse sand) including grouting the joints with white cement and matching pigments etc,complete.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (Thickness to be specified by the manufacture) of approved make in all colours, shades except burgundy , bottle green , black of any size as approved by Engineer-in-charge in skirting , risers of steps and dados over 12 mm thick bed of cement Motar 1:3(1 cement: 3coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing 18 mm thick gang saw cut, mirror polished,premoulded and prepolished, machine cut for kitchen platforms,vanity counters, window sills, facias and similar locations, of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups,including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Granite of any colour and shade Area of slab over 0.50 sqm

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished seamless type tubes

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

1.00 mm thick with zinc coating not less than 275 gm/mz

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden frames with rawl plugs screws etc

Providing and fixing factory made uPVC white colour casement/ Casement cum fixed glazed door comprising of uPVC multi-chambered frame, sashand mullion (where ever required) extruded profiles duly reinforced with1.60 ± 0.2 mm thick galvanized mild steel section made from roll formingprocess of required length (shape & size according to uPVC profile), uPVCextruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy(white powder coated) 3D hinges and one handle on each side of panelsalong with zinc plated mild steel multi point locking having transmissiongear, cylinder with keeps and one side key,G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glasspanes and silicon sealent shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.

Casement door with top hung ventilator with 3D and S.S. friction hinges (400 x 19 x 1.9 mm) made of (big series) frame 67 x 64 mm, sash 67 x 110 mm & mullion 67 x 80 mm all having wall thickness of 2.3 ±. 0.2 mm and single glazing bead / double glazing bead of appropriate dimension.(Area of door upto 2.50 sqm)

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chamberedframe with in-built roller track and sash extruded profiles duly reinforcedwith 1.60 ± 0.2 mm thick galvanized mild steel section made from rollforming process of required length (shape & size according to uPVCprofile), appropriate dimension of uPVC extruded glazing beads and uPVCextruded interlocks, EPDM gasket, wool pile, zinc alloy (white powdercoated) touch locks with hook, zinc alloy body with single nylon rollers(weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size forfixing frame to finished wall and necessary stainless steel screws etc.Profile of frame & sash shall be mitred cut and fusion welded at all corners,including drilling of holes for fixing hardware's and drainage of water etc.After fixing frame the gap between frame and adjacent finished wall shallbe filled with weather proof silicon sealent over backer rod of required sizeand of approved quality, all complete as per approved drawing & directionof Engineer-in-Charge. (Single / double glass panes, wire mesh and siliconsealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.

Two track two panels sliding window made of (small series) frame 52 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm)

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick:

Float glass panes.5.5 mm thick glass pane.

Float glass sheet of nominal thickness 8 mm (weight not less than 20.00kg/sqm) for glazing in UPVC Door and flush Door

Providing and fixing factory made Fiber glass Reinforced plastics (F.R.P.) chajja 4 mm thick of required colour, size and design made by Resin Transfer Moulding (RTM) Machine Technology, resulting in void free compact laminate in single piece, having smooth gradual slope curvature for easy drainage of water and duly reinforced by 2 nos vertically and 1nos horizontally 50x2 mm thick M.S. flat with 12 mm in built hole for grouting on the existing wall along with the 50 mm flanges duly inserted and sealed in the wall complete in one single piece casted monolithically, including all necessary fittings. The FRP Chajja should be manufactured using unsaturated Polyester resin as per IS : 6746, duly reinforced with fibre glass chopped strand mat (CSM) as per IS : 11551 complete with protective Gel coat U/V coating on Top for complete resistance from the extreme of temperature, weather & sunlight.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).

Sal wood

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.

35mm decorative flush door shutters incl. SS butt hinges

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of shutters (overall area of door shutter to be measured)

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.

Supplying & Providing Polycarbonate Transparent Roofing Sheet of material Virgin thermoplastic polycarbonate resin (often brands like SABIC or Covestro Makrolon) Standard Thickness 8 mm, Flat, glass-like clarity or colour, maximum strength, Impact Resistance: Up to 200 to 250 times stronger than standard glass and 30 times stronger than acrylic, UV Protection: Co-extruded UV-stabilized layer on one or both sides to prevent yellowing and block harmful radiation, Fire Rating: Class 1 / Class B-s1, d0 (self-extinguishing, does not spread flames or drip toxic gases) and as per directions of Engineer-in-charge.

Supplying & Providing Standard S.S. Tubular Door Handle for Doors on each side as per directions of Engineer-in-charge.

Supplying & Providing Standard Door Stopper as per directions of Engineer-in-charge.

Supplying & Providing Hydraulic Door Closer as per directions of Engineer-in-charge.

Supplying & Providing all Hardware sets incl. Mortice lock, Tower locks of standard Quality as per directions of Engineer-in-charge.

TOTAL (Part I) (including 18% GST as per Company norms)

PART II (INTERIOR WORK)

False Ceiling work in Seminar Hall, VIP Lounge and Library Area

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80mm with tapered flanges of 26mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230mm long G.l. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450mm centre, with 25 mm long dry wall screws @ 230mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutoutsmade with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

Fully Perforated Gypsum Plaster Board of size 1200 × 2400x12.5 mm having approx. 15% perforated area with perforation size and pattern as approved by the Engineer-in-charge and as per manufacturer's specification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.60.

Providing and fixing thermal insulation with Resin Bonded rock wool conforming to IS: 8183, having density 48 kg/m3,50 mm thick, wrapped in 200 G Virgin Polythene Bags fixed to wall wirh screw, rawel plug & washers and held and in position by criss cossing GI wire etc. complete as per directions of Engineer-in-Charge.

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on interlocking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 × 37 × 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50mm long dash fasteners, 4 mm Gl adjustable rods with galvanized butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.

8mm thick fully perforated calcium silicate board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process to give stable crystalline structure with minimum compressive strength 225 kg/ sq. cm, bending strength 100 kg/sq. cm, of size 595x595 mm, having perforation of dia. 10 mm with minimum perforated area 18 % with non woven tissue on the back side, having an NRC (Noise Reduction Coefficient) of 0.85, with 50mm thick rockwool of 48 kg /cum backing.

Wooden Flooring and Skirting in Seminar Hall

Providing & fixing in position Phenol bonded Bamboowood flooring with planks of sizes 14mm thick, minimum 1800mm length and minimum 100mm wide, in approved colour, texture and finish, having Performance Appraisal Certificate (PAC) issued by Building Materials & Technology Promotion Council (BMTPC). The flooring shall be fixed with tongue and groove interlocking system, with underlayment of 4mm thick expanded polythylene foam sheets having density 40kg/cum, over prepared surface with necessary quarter round planks of size 1900mm × 18mm and door reducer of size 1900mm x 44mm, wherever required. The bomboo wood planks shall have minimum density of 1000 Kg/cum & minimum Hardness 1000 Kgf. with Eco friendly UV coating, all complete as per direction of the Engineer in-charge.

Providing & fixing in position Phenol bonded Bamboo wood in wall skirting with planks of sizes 14mm thick, 1900mm length (minimum) and 85mm wide(minimum), in approved colour, texture and finish, having Performance Appraisal Certificate (PAC) issued by Building Materials & Technology Promotion Council (BMTPC). The skirting shall be fixed with SS screws & rawl plugs, over underlayment of 4mm thick, expanded poly ethylene foam sheets having 40kg/cum density over prepared surface. The bomboo wood planks shall have minimum density of 1000 Kg/cum & minimum Hardness 1000 Kgf. with Eco friendly UV coating, all complete as per direction of the Engineer in-charge.

Wall Paneling in Seminar Hall and VIP Lounge

Armstrong Wood Works wall Panel: Providing and Fixing Armstrong Channeled Woodworks perforated panels of width 192mm, thickness of 15mm and length 2400 mm or as required by the Architect/ approving engineer, made of Moisture Resistant fibre board with minimum 595 Kg/M3 density substrate with a laminated facing as per the approved shade & finish and a melamine balancing layer on the reverse side. The boards shall have a special perforation pattern where the visible surface has a “Helmholtz” fluted perforation of 3mm width and 21mm of visible panel each. The edges of the panels shall be “tongue-and-grooved” to receive special clips for installation. The back of the perforated panel shall have sound absorbing nonwoven acoustical fleece having NRC of 0.52. The panels shall be mounted on special aluminum splines using clips provided by Armstrong and approved by the Architect/ Engineer-incharge. INSTALLATION: Install wooden battens (provided by others) of section 50x50mm or as approved by the Architect on the solid wall horizontally using screws and plugs at spacing of 600mm center-to-center. Screw the aluminum extruded keel for channeled woodworks provided by Armstrong over the lowest and second wooden batten at an on-center distance of 600mm. Install the Skirting (provided by others) of width 50mm or more as required by the Architect/ Engineer-incharge and insert the tongue end of the panel in the skirting. Place the inside clip on the groove end of the panel along the Al keel and then place the tongue end of the next panel. Continue installing rows of panels by inserting the tongue into the groove of the earlier inserted panel and progressively installing inside clips into the next keel till the actual height is achieved. Finish off the edges using wooden molding of matching color (provided by others). Installation to be carried out by Armstrong Trained Installation team & Installation should be carried out as per Armstrong recommended procedure

Wall Panelling Finished with Laminate

P/F Wall panelling with Seasoned Malaysian Sal Wood Members of the minimum size (nominal) 50mm x 25mm, (a bigger size may be required at the corners, etc)firmly affixed to the supporting wall at a maximum spacing of 450mm x 450mm c/c, (the spacing shall need to be closer, if the room grid so dictates), 18.0 mm thick BWP plywood firmly fixed to the wooden frame, and covered with 1mm laminate of the given shade / colour / texture / approved brand or equivalent, in approved pattern. The laminate may have a number of horizontal and vertical grooves / patterns / SS beadings as per designs and drawings. The Wooden Frame shall be coated with anti-termite paint (Chloropyrophos) as per the Manufacturers Specifications. The panelling shall be at the required distance from the wall, as per instructions of the Project Engineer. Note - all specifications is as per wall panelling

Note given below will be considered for all types of wall panelling

All electrical wires, accessories, telephone wires, etc, shall be run in the panelling as per Electrical Drawings and designs. Nothing extra shall be paid for the co-ordination of the same.

All items necessary for completing the above mentioned work are deemed to be included in the scope of work, whether or not they are specifically mentioned in the B.O.Q / tender documents / drawings.

All exposed wooden surfaces are to be polished and protected with Melamine Polish, and shall be of 1st quality teakwood.

All complete as per drawings, designs, specifications and directions of Engineer-in-Charge.

Column / Wall Panelling (upto false ceiling ht, with a finishing bead above)

Wall Panelling Finished with Louvers

Providing and fixing interior decorative louvers made of 25 x 50 mm section in approved BWR grade plywood , placed at 75 mm c/c with uniform spacing, including 50 x 25 mm treated hardwood subframe, fixing to wall with suitable fasteners, PU adhesive, SS screws, cutting, groove making, edge finishing, laminate / veneer / PU polish as approved, complete in all respects.

Window Curtain for all Windows

Roller blind fabric should be made up of 35% Fiberglass, 65% Vinyl on Fiberglass. It should have 3% openness, fabric thickness should be 0.50-0.55 mm, fabric weight should be 478 grams per square meter.

Roller Upper Tube: Made of high strength extruded aluminium alloy, finish powder coated with min 60 micron coating, Size of 40 mm outer dia and wall thickness of min. 1.2mm, Special feature, it has end to end groove to hold fabric inside for better strength. Bottom Tube: Made of high strength extruded aluminium alloy, finish powder coated with min 60 micron coating, Size of 20 mm height and wall thickness of min. 1.2mm, Special feature, it has end to end groove to hold fabric inside for better strength. Control Unit: Made of high strength reinforced Nylon grade 6, consisting of outside sleeve and centre shaft, sleeve shall provide bearing surface of roller tube and rotate freely on centre shaft, providing smooth quiet and long wearing operations. Brackets: Fixing brackets is made of mild steel with zinc coating, made of thickness of min. 0.7mm. Ball Chain: Made of 2mm thickness polyester cord with moulded 4.5mm round plastic balls.

Supply and Installation of storage/Cabinet

Library Full height Cabinet (Upto false ceiling height) - Cabinet Manufacturing, providing and PlacingCabinet of following dimensions with the following specifications. The cabinet will be made from 12mm , 18mm -ply bwp finished with 1mm thk laminate as per approved shade and colour. The racks and shutter of the cabinet will be manufactured as per the design provided. The shutter of cabinet will be made up of 6mm thk glass. The beads on the edge of the cabinet and door shutter will be as per the design provided.The work to be done as per the direction of E/I.The above cost includes the cost all work. The fittings will be of Haffle/ Hettich /Equivalent.For Payment elevation area to be considered.

Libraray low height Cabinet (2'-6" ht)- Cabinet Manufacturing, providing and Placing Cabinet of following dimensions with the following specifications. The cabinet will be made from 12mm , 18mm -ply bwp finished with 1mm thk laminate as per approved shade and colour. The racks and shutter of the cabinet will be manufactured as per the design provided. The shutter of cabinet will be made up of 6mm thk glass. The beads on the edge of the cabinet and door shutter will be as per the design provided.The work to be done as per the direction of E/I.The above cost includes the cost all work. The fittings will be of Haffle/ Hettich /Equivalent.For Payment elevation area to be considered.

Providing and placing Meeting tables at Library for 8 PAX: Worktop: Worktop shall be made out of f 12mm thk. BWP ply cover with acrylic laminate and all the edges of worktop shall be provided with machine pressed 1.5-2 mm thick ABS edge banding glued with hot melt EVA glue.The height of Worktop shall be 750 mm from ground level. Understructure: SS understructure with 50mm x 50mm C type square straight leg, well supported with MS beams under table top to supported top & connected to leg to leg.

Providing, supplying, installation, testing and commissioning of floor-standing premium wooden lectern/podium of approx. 650 × 500 × 1150 mm, fabricated from 18 mm BWP plywood/MDF with approved laminate and PU finish, inclined reading top, internal storage shelf, concealed cable management, institutional logo provision, LED reading light, 2 Nos. microphone mounting provisions including 1 No. professional cardioid/super-cardioid gooseneck condenser microphone with XLR connectivity, integrated electrical module comprising 2 Nos. 6A power sockets, USB-A/USB-C charging, HDMI, CAT-6 and audio connectivity, internal FRLS wiring, shielded microphone cable, necessary conduits, connectors, hardware, supports, earthing and complete integration with seminar hall sound system, all complete as per approved shop drawing and direction of Engineer-in-Charge.

TOTAL (Part II) (including 18% GST as per Company norms)

PART III (FURNITURE WORK)

Auditorium Chair - Moulded PU Foam of density of Minimum 45 P/ MTR .Cube with Good looking & Strength. The Main load bearing stand shall be of Tubular Steel stucture. Metal Frame for seat & Back From Floor - Minimum height of chair - 970mm From Floor - Minimum height of Seat - 435mm Centre to centre - 535mm . Depth of Seat - 450mm The Seat & Back Frame should be Covered with PPCV Tray. The Common Armrest should be of PPCP with Cupholder. Seat should be in Auto Tip up in Pushback Mechnisum. he Product Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC. MAKE : DURIAN/GODREJ/WIPRO/HNI or Equivalant.

3 Seater Sofa- Sofa Size( (L)1905mm X (D)890mm X (H)870mm)mm. Frame used is treated American pine wood with termite free & borer free. Soft & comfortable cushion with high density and resilient foam. Frame used is Treated american pine wood & the wood used in sofa has been 8% moisture, this prevents the wood from wrapping and bending. all wood used is termite free and borer free. Foam of sofa comfortable cushion with high density and resilent foam. all apholstry materials used in specially designed. all plywood used in M R Garde. Color-Black/Brown.The Product Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC & PEFC. MAKE : DURIAN/GODREJ/WIPRO/HNI or Equivalant.

1 Seater Sofa: 1 Seater Sofa Size (870x870x870)mm. Frame used is treated American pine wood with termite free & borer free. Soft & comfortable cushion with high density and resilient foam. Frame used is Treated american pine wood & the wood used in sofa has been 8% moisture, this prevents the wood from wrapping and bending. all wood used is termite free and borer free. Foam of sofa comfortable cushion with high density and resilent foam. all apholstry materials used in specially designed. all plywood used in M R Garde and are made by Durian. Color-Black/Brown.The Product Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC & PEFC. MAKE : DURIAN/GODREJ/WIPRO/HNI or Equivalant.

Center Table - Center Table Size (W)1200mm X (D)600mm X (H)450mm. • Ideal for compact Urban spaces • Shelf storage offers generous space for books or magazines • Steam Beech wood base makes it highly durable • Easy to clean table stays newer for longer • Made from sustainably sourced Beech wood. The Product Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC & PEFC. MAKE : DURIAN/GODREJ/WIPRO/HNI or Equivalant.

Side Table - Side Table Size (W)600mm X (D)400mm X (H)500mm • Ideal for compact Urban spaces • Shelf storage offers generous space for books or magazines • Steam Beech wood base makes it highly durable • Easy to clean table stays newer for longer • Made from sustainably sourced Beech wood. The Product Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC & PEFC. MAKE : DURIAN/GODREJ/WIPRO/HNI or Equivalant.

Medium Back Chair - Medium back 360㸠degree revolving chair, * all over size is : 580mm lx 670mm dx 1110mm h , *the chair made of full upholstery in black colour . It will comes in matte finsih in contemporary style . Details : * arms : amrest is having two adjustment heights up & down . * use of ply: 12 mm thick hot pressed bwr plywood is grade - 303 for seat and back . * seat: 40 ã± 2 mm thick polyurethane foam with density 32 ã±3 kg per cu meter for best quality cushioning in seat , * back : 40 ã± 2 mm thick polyurethane foam with density 32 ã±3 kg per cu meter for best quality cushioning in back . Backrest support foam design based on symmetrical lumbar support * mechanism : single locking mechanism . Seat maximum height is 580mm & minimum height is 480mm & back height from floor maximum height is 1110mm & minimum height is 1010mm * gas lift 100 mm telescopic haudraulic * base : 650mm nylon base with smooth castors. The seller / company should be nabcb certified iso-9001:2015, iso-14001:2015, ohsas-18001:2007, iso-45001:2018, iso-50001:2018, iso 37001-2016 and iso-13485. MAKE : DURIAN/GODREJ/WIPRO/HNI or Equivalant.

Providing, fabricating, supplying, and installing a free-standing wooden speaker podium (lectern) complete in all respects including material, hardware, finishing, and accessories as per approved design and specificatin Overall Height: 1100 mm ± 50 mm.Top Size: 550 mm × 400 mm (approx.)Base Size: 450 mm × 350 mm (minimum).Top Inclination: 10°–15° slope for reading comfort .Made from 19 mm thick BWP grade plywood (ISI marked, IS:710) .Internal framing with seasoned hardwood battens (minimum 50×25 mm) .All joints to be screw-fixed + adhesive bonded .Laminate / veneer shade to be approved by Engineer in charge prior to excution. DURIAN/GODREJ/WIPRO/HNI or Equivalant.

TOTAL (Part III) (including 18% GST as per Company norms)

PART IV (ELECTRICAL WORK)

Unskilled labour for Dismantling old electrical wiring, fixtures, old panel/DB boxes and redundant conduits; stacking serviceable material

Skilled Labour(Electrician) for refixing of Cubicle panel and Line connections etc.

Wiring for light point/ fan point/ exhaust fan point/ call bellpoint with 1.5 sq.mm FRLS PVCinsulated copper conductor single core cable in surface / recessed medium class PVC conduit with modular switch , modularplate, suitable size G.l. box etc as required.

Group C

Wiring for light/ power plug with 2 X 4 sq. mm FRLS PVCinsulated copper conductor single core cable in surface /recessed medium class PVC conduit along with 1 Nos 4 sq.mm FR PVC insulated copper conductor single core cablefor loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire withthe following sizes of FRLS PVC insulated copper conductor,single core cable in surface/ recessed medium class PVCconduit as required.

Supplying and fixing recess mounted 36 watt LED flat panel (2' X 2') with minimum efficacy 100 lm/w which privides soft light and glare free symmetrical illumination suitable for armstrong/grid ceiling and integrated electronic driver etc directly on false ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor cable etc as required.

Supplying and fixing 4'X18 wat[ LED batten with minimum efficacy 100 lm/w in polycarbonate housing and complete with integrated electronic driver etc directly on wall/ ceiling including connections with 1.5 sq.mm FRLS pVC insulatedcopper conductor etc. as required.

Supply and installation of regular/standard model A.C. ceiling fan of 1200 mm sweep with service value (CM/MM) minimum 4.00, Air delivery minimum 270 cum/min including wiring the down rods of standard length (upto 30cm) with 1.5 sq. mm FRLS PVC insulated copper conductor etc as required.

Supply and installation of 400 mm, 230 V A.C. wall/cabin fan including fixing the bracket, making connection, testing, commissioning etc as required

Supply and fixing of following sweep/ sizes PVC/ABS squarebody Exhaust Fan with automatic openable louvre shutter in existing opening including making connection, testing etc as required.

200 mm sweep (1300i1400 RPM)

Supplying and fixing , following ways, surface/recess mounting, Vertical three phase distribution board ( VTPN DB's ) of CRCA sheet steel, dust protected, duly powder painted suitable for upto 160 amp, four pole MCCB as lncomer and SP/TP MCB's as outgoing inclusive of tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's etc as required. (but without MCCB & MCBS)

8-way VTPN main distribution board suitable upto 160A MCCB

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections etc. as required'

160 A, 36 KA, FPMCCB

Supptying and fixing following rating, 24Al4L5 volts, "C" curve, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required'

6–32A SP MCB outgoing protection

Providing chemical/mineral maintenance free earthing system comprising of copper coated earth electrode 3 metre length and 17.2 mm outer dia along with 25 kg earth conductivity enhancing back fill mineral compound for eafth electrode to fill up the excavated earth and earth inspection pit etc. as required.

Providing and fixing 25 mm X 5 mm G.l. strip on surface orin recess for connections etc. as required.

TOTAL (Part IV) (including 18% GST as per Company norms)

PART V (PHE WORK)

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing 600x120x5 mm glass shelf with edges round off,supported on anodised aluminium angle frame with C.P. brassbrackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Flexible pipe

40 mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I brackets and stainless steel plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required:

Kitchen sink with drain board

510x1040mm bowl depth 178mm

Unskilled labour for Dismantling existing sanitary/CP fittings and making safe for replacement

Semi-Skilled Labour (Plumber) for necessary fittings and existing connections etc.

Providing and fixing wall mounted with modern life edgeWH toilet with UF seat including INSTAFLUSHTM Next GEN- Mech in wall tank and LYNK faceplate polished Chrome including all fittings and fixtures with seat cover, health faculet ,cistern fittings like M12 rack bolts, gasket etc. Including making connections with the existing P/S trap, complete in sll respect as per direction of E/I.Make Jaquar /Kohlar

Providing and fixing counter basin size- (mm) 190x550x430 (Jaquar,CAT NO- FLS-wht-5701) including fixing and all accessories as per manufacturers specification and direction of Engineer-in-charge..Make Jaquar /Kohlar

Providing and fixing white vitreous wall -hung urinal of approved make and size approx. size 610 x 390 x 370 mm complete with manual flushing arrangement(flush valve/ flush cock) including necessary inlet connection from back side , outlet, brackets, and all required fittings. the work shall be executed as per manufacturers specification and direction of Engineer-in-charge.Make Jaquar /Kohlar

Providing and fixing C.P. health faucet (jet spray) complete with ABS/CP body, trigger operated hand shower, 1.2 metre long flexible SS/PVC braided hose, and wall hook, including all necessary fittings and connections, complete in all respects as per direction of Engineer-in-charge.Make Jaquar /Kohlar

Providing SS floor trap with grating as per direction of Engineer Incharge.

Providing Paper holder (jaguar AKP-35753PS). Make Jaquar /Kohlar

Providing Towel Ring make (Jaquar product No. AKP-35751P ). Make Jaquar /Kohlar

Providing Soap dispenser make (jaguar AKP-35735P),Make Jaquar /Kohlar

Providing CP brass 2-way bib cock with wall flange(Kubix-F) 15mm. Make Jaquar /Kohlar

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.make kohler, jaquar.

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.

15 mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.

15 mm nominal bore

Supplying and Providing of 75mm SWR waste/vent pipe incl. fittings/clamps as per direction of Engineer Incharge.

Supplying and Providing of 110mm SWR soil pipe incl. fittings/clamps as per direction of Engineer Incharge.

Supply and installing 150 mm dia (6") chimney flue/duct installation kit of total length 3.0 m, comprising suitable metal flue pipe, required bends/connectors, clamps, supports, termination/rain cap and all necessary accessories, including cutting, jointing, sealing, alignment, fixing and complete installation as required at site, complete in all respects.

Providing and fixing Wall Mixture for hot and cold water supply in bathroom and Toilet as per direction of Engineer Incharge. Make Jaquar /Kohlar

TOTAL (Part V) (including 18% GST as per Company norms)

PART VI (AC WORK )

SPLIT AC (inverter model, 5 star, Cooling only):- Supply, installation, testing and commissioning of Split type wall mounted air conditioning unit of following capacity including indoor, outdoor unit fitted with inverter based rotary compressor, copper condenser and first charge refrigerant R410A. The condensing unit working range should be capable for providing cooling between +/-5 deg. C to 50 deg. C & heating within 0 deg. C to 15 deg. C including connection of copper pipe of required size upto 3 mtr., insulation, cordless remote control, auto air swing louvers, connection copper lead wire, condensed water outlet pipe 2 mtr. complete etc as required. 0utdoor/ indoor units should be of same make (brand). The cost includes contractor profit, labour cess, supply, transportation cost, installation, testing and commisioning cost.

Cassette AC (Ceiling suspended/mounted cassette type 4 way unit with inbuilt drain pump & decorative panels.):- Supply installation testing and commissioning of split type ceiling cassette air conditioning unit of capacity including indoor, outdoor unit fitted with rotary compressor, copper condenser and first charge refrigerant R410A/ecofriendly green gas only, cordless remote control, auto air swing louvers, connection copper lead wire between outdoor and indoor unit, connection copper lead wire upto 1.5 mtr., excluding connection copper pipe of required size, insulation, floor stand for outdoor unit, condense water outlet complete etc as required. Outdoor/indoor units should be of same make (brand). The cost includes contractor profit, labour cess, supply, transportation cost, installation, testing and commisioning cost.

Supply installation testing and commissioning of Atomatic Voltage Stabilizer of Capacity 4 KVA, input voltage -130V± 10% and output-220 V ± 10% of Capacity & input Range 130V to 280V Model (For 1.5 Ton AC)

Supply installation testing and commissioning of Atomatic Voltage Stabilizer of Capacity 5 KVA, input voltage -130V± 10% and output-220 V ± 10% of Capacity & input Range 130V to 280V Model (For 1.8/2.0 Ton AC)

Supply and fixing of 20/24'' ready made M.S. prepainted wall stand structure suitable for 1.5/2.0 TR split AC Machine including all accessories.

Refrigerant:- Supply and additional refrigerant charge of refrigerant R410/410A & equivalent Eco friendly green gas to compensate the additional piping done at site for all systems including testing commissioning as required.

Drain piping :- Providing and fixing of CPVC, 6Kg/cm2 drain water piping with fittings, support and insulated with 6 mm thick closed cell elastomeric nitrile rubber insulation complete as per specification.

Supply and fixing of size 100mmX100mmX100mm PVC Tray with cover for covering of insulated copper pipes of AC.

Copper piping: - Supply, installation, testing and commissioning of interconnecting copper refrigerant pipe work (19mm/13mm thick) duly insulated with elastomeric nitrile rubber type tubular insulation between indoor & outdoor units as per specifications. And exposed piping should be wrapped with glass woven cloth and lag coating for vapour barrier and weather protection. Joints shall be covered with nitrile rubber tape of 3 mm thick complete as per specification.

Outdoor stand fabrication :- Supply, fabrication and erection of angle/channel/flat iron stand, hanging arrangement for air conditioning machines & ducts etc, back /support clamps or other similar work etc. including nut bolts of required size, making holes, fabrication, welding, cutting, etc. and painting with one coat of red oxide paint & two coat of enamel paint as required as per specification.

TOTAL (Part VI) (including 18% GST as per Company norms)

PART VII (AUDIO PA SYSTEM FOR CONFRENCE HALL)

SITC of 86" UHD IR interactive display, 390 nits (Typ.) or above, 20 touch point, 10 writting points, with OPS device ( 8 GB RAM, i5 processor, 500 GB SSD, WIFI & 2 LAN Ports ) , 8ms response time, USB(2.0)- 3 nos, USB (3.0)- 2 nos, HDMI(3), VGA(1), Touch out (2),inbuilt speaker 10+10 w, 32GB storage, Android 9 & above, Cloud upload ,WebBrowser,Easy Cast/Screen Share from Mobile/Laptop/PC. Make - Panasonic / LG

SITC of 4" two-way Ceiling loudspeaker SPK−C412 100V – 7.5W/15W/30W. paintable thin edge grill, frequency response in Hz 95 - 20K, NOMINAL SENSITIVITY: 84dB SPL @1m, 1W or better. Make- Kramer/ equi

SITC of Mixer-Amplifiers 120watts, 4 inputs with 1 output, Supports 70V and 100V distributed audio systems, Energy Star® Certified. (MAF) Required from the OEM. Warranty should be 5yrs. Make - Australian monitor/Equi.

D-cerno F-DM Flushmount Delegate Microphone Unit Digital signal processing Tactile microphone push button with integrated LED Removable microphone connector: possibility to use different microphone lengths (30, 40, 50, 70, Full Flex).Make-Televic/Equi.

D-cerno F-CM Flushmount Chairman Microphone Unit High quality integrated loudspeaker Concealed conference bus connections 'Prior' button, Next-in-line button Digital signal processing.Make-Televic/Equi.

Gooseneck microphone lengths 50 CM ( D-MIC-50SL).Make-Televic/Equi.

Conference System interface cable. 2Mtr (ICC5/2).Make-Televic/Equi.

Conference System interface cable. 5Mtr (ICC5/5).Make-Televic/Equi.

Conference System interface cable. 10 or 20Mtr (ICC5/20).Make-Televic/Equi.

High–Speed HDMI Cable with Ethernet, K–Lock Pull–Resistant Connectors.Make- Kramer/ crestron

SITC of All required Cables and Connectors. SITC of 2core 18AWG PVC insulated Speaker Cable, power cable and Required connectors and accessories(Lot).Make- Kramer/ crestron

SITC of Cable Cubby with Connectivity of HDMI,and Power Sockets including accessories.Make- Gigatron/ Logic

SITC of PVC conduit as required.(lot).Make- AKG/eqv

SITC of Equipment rack 9U with tray, PDU and accessories as required.Make-Dynamic/ Eqv

Supply Installation testing and commissioning charges.Make - Integrator/equi

Led TV for VIP Lounge -1m 63cm (65") QN90C Neo QLED 4K Smart TV.Quantum Matrix Technology/Neural Quantum Processor 4K/Dolby Atmos/ Built-In loT Hub/HDR+ with 60W Sound* (In Sizes 55 or above) (QN90C). Make- Samsung/Sony

TOTAL (Part VII) (including 18% GST as per Company norms)

GRAND TOTAL

NOTE: 1. This sheet is protected. Bidders are adviced to fill Name, address, contact details & Quoted rate in coloured cell & upload the filled document/ Financial Bid over website while filling the tender online. 2. Rates shall be quoted inclusive of GST, Carriage cost of materials, all transportation and Seigniorage cost, duties, fixing cost and all applicable taxes. 3. Any mismatch in quoted amount in tender and quoted amount in Financial sheet would lead to disqualification of the bid. 4. The Seigniorage fee shall be calculated as per below rate: a) Coarse Sand- Rs. 18.46/Cum b) Stone Aggregate- Rs. 62.51/ Cum c) Local Sand- Rs. 14.89/ Cum d) Bricks- Rs. 9.6/ 1000 e) Earth- Rs. 3.64/ Cum