Construction of Balance work for Government Degree College Drass Kargil

Amount

ARCHITECTURAL

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in superstructure above plinth level upto floor five level including curing in Cement mortar 1:6 ( 1 cement : 6 coarse sand)

Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level

Half brick masonry with common burnt clay (non-modular) bricks of class designation 7.5 in foundations and plinth including curing in : Cement mortar 1:4 ( 1 cement : 4 coarse sand).

Extra for half Brick masonry in superstructure above plinth level upto floor V level

Extra for providing and placing in position 2 Nos. 6mm dia. M.S. bars at every third course of half brick masonry.

15mm cement plaster on the rough side of single or half brick wall of mix 1:6 (1 cement: 6 fine sand) (including cost of all material, leads, lifts and carriages etc upto site of work complete).

12 mm thick cement plaster on ceilings, etc. in (1 cement: 4 fine sand mix). Upto floor V level complete in all respects (including cost of all material, leads, lifts and carriages etc. upto site of work complete).

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): First class deodar wood

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. With ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws 35mm thick

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured)

Providing and fixing 35 mm thick panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: -Butt hinges and necessary screws shall be paid separately)

Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge :

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

Providing and fixing 4mm thick panels of plain glass for fixed glazing panels/ shutters (only panel area to be measured) including cost of teak wood beadings of required size complete

Providing and fixing hardware fittings of approved brand and of required type as approved by Engineer incharge. complete as per the specifications . (Brass)

Modular door lock ss finish handle 10" with duaal locking system inside & outside (godrej)

Tower bolts 100mm (windows)

Handle 100mm (window)

I-Hooks 150mm

Tower bolts 150mm (doors)

Handle 125mm (door)

butt hinges of 100x63x3.2 mm

Granite Work in Floors :- Providing and fixing ( gang saw cut mirror polished (flamed , pre-moulded and pre-polished), machine cut for flooring, steps ,risers of stairs etc.( flamed instaircase) of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding (of edges wherever required ) and polishing to edge to give high gloss finish etc. complete at all levels. Granite of any colour and shape 18mm thick. and slab area over 0.50 sq m. (Note: The Granite stone slab shall be cut to required size and laid to the required pattern including rounding, chamfering, bull nosing of the edges as directed. Actual area of slab, as laid shall be measured) Sample to be approved by Engineer-in-charge. (including cost of all material, leads, lifts and carriages etc. upto site of work complete

Providing and fixing 1st quality Vitrified Double Charged tiles in floor/skirting etc. of standard thickness of approved make in all colours, shades, design and prints as approved by the engineer-in-charge over 12 mm thick bed of cement mortar 1 : 3 (1cement 3 coarse sand) and jointed with grey cement slurry @ 3.3 kg per Sqm. Including pointing in white cement mixed with pigment of matching shade with all lead, lift, labour, materials, tools, plants complete as per specification and as directed by Engineer in Charge ..

Providing and fixing 1st quality ceramic glazed floor tiles conforming toIS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing of 35 mm thick Wood pannelled Door shutters of Kail wood , excluding cost of hinges but including labour for the same.

Kota stone slab flooring 25 mm thick over 20mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing, polishing and curing complete with base of cement mortar 1:4 (1 cement : 4 coarse sand) :

Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 2mm thick

Wall Painting with acrylic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work

With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work

Proving and fixing of 24 mm thick rubber wood board for wall penelling designed in ornamental pannals shape square / rectangular. Including cost of necessary adhesive ,budloo wood backing and cost of nails etc specification and design approved by engineer in charge/consultants.complete job.

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with Armourcrete of M/s The Structural Water Proofing Company Pvt. Ltd. Or Tapecrete of M/s CICO Technologies Ltd. consisting of applying : First layer of slurry of cement @ 0.488 kg/Sqm mixed with Armourcrete or Tapecrete @ 0.253 kg/Sqm. This layer will be allowed to air cure for 4 hours. Second layer of slurry of cement @ 0.242 kg/Sqm mixed with Armourcrete or Tapecrete @ 0.126 kg/Sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. (The rate includes supply of waterproofing compound, preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry)

French spirit polishing, Two or more coats on new works including a coat of wood filler

Providing/fixing of Khatambandi Ceiling of ist Class Budloo Wood of specified pattern in ceilings etc. including, necessary frame work work of 50 mmx 75mm size ,and 12mm thick ply board frame in lining of Budloo wood underneath and other incidentals including cornice of size 75mmx75mm/2 of Budloo Wood all complete in all respectes.as per the directions of Consultant/as per the drawings enclosed

Providing & applying Plaster of Paris (gypsum anhydrous) suspended false ceiling Cove false ceiling), up to any height above floor level, including fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive). Consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts. Other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size.

The other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre. This shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval and reinforced with rabbit wire mesh of 100mmx16mm gauge fixed to frame.

Providing and Fixing of 50mm dia stainless steel railing of 304 grade of hallow tube 1.6 mm thick of Jindal/Salem make or equivalent including welding and fixing with stainless steel machine screws for making required size and shape, buffing etc. Complete and fixing stainless steel balusters upto 900 mm height and S S tubes, three in one installed horizontally including cutting, welding, grinding to required shape and size by required steel dash fasteners, nuts, bolts, screws ,etc. in floors and treads including providing SS shoe at each balusters complete as per architectural drawings and as per the directions of engineer incharge including cutting of granite/marble floors and fastening with lead grouting if required, complete in all respects.

Providing and Fixing of 50mm dia stainless steel railing of 304 grade of hallow tube 1.6 mm thick of Jindal/Salem make or equivalent including welding and fixing with stainless steel machine screws for making required size and shape, buffing etc. horizontally including cutting, welding, grinding to required shape and size by required steel dash fasteners, nuts, bolts, screws ,etc. in walls complete as per architectural drawings and as per the directions of engineer incharge including fastening with lead grouting if required, complete in all respects.

Providing & fixing of stainless steel nevel post (Ornamental ) including top ball of AISI 304 grade of required height duley anchored to floor with dash fasteners . Height of the nevel post shall not be less than 1050 mm above the finished skirting level all complete as per architectural drawings (including cost of all material, leads, lifts and carriages etc upto site of work complete).Complete as per the directions of Engineer incharge.

Finishing walls with textured exterior paint of required shade on New work (two or more coats applied @ 3.28 liter/10sqm) over and including base coat of exterior primer applied @ 2.20kg/10sqm

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry bricks 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth.

STRUCTURAL

Cast-in-situ of concrete work of nominal mix concrete M7.5 grade (1:4:8) nominal maximum size of stone aggregate 40mm volumetric batching in ground floor rooms and class room steps including curing but excluding formwork costs.

Cast-in-situ of concrete work of nominal mix concrete M10 grade (1:3:6) nominal maximum size of stone aggregate 20mm volumetric batching in ground floor rooms and class room steps, including curing but excluding formwork costs.

Cast-in-situ of concrete work of nominal mix concrete M15 grade (1:2:4) nominal maximum size of stone aggregate 20mm volumetric batching in ground floor rooms and class room steps, including curing but excluding formwork costs.

Filling in plinth by non-clayey class 2 sand or GSB material with proper consolidation.

Cast-in-situ design mix of M20 grade, water cement ratio as per design, nominal max size of stone aggregate 20mm, weigh batching, including curing but excluding formwork costs for all RCC works from foundation to roof level.

Form work of steel plates not less than 3.0mm thick M.S. sheets of specified size stiffened with suitable structural frame work true to plane or Kit-ply plates of not less than 12mm thickness of specified sizes stiffened with a suitable timber frame work prop height up to desired height in foundation, plinth beams, all types of suspended floors, soffits of slabs, sloping areas, sides and soffits of beams ribs, columns posts, pedestals, up to desired heights and thickness complete including its removal for all RCC works from foundation to roof level

Providing, assembling and placing high strength deformed steel bars of Fe500 grade (conforming to IS 1786-1985) for RCC work including cost of binding wire for all levels from foundation to roof, including R/F used in as per details.

PLUMBING & SANITARY

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets,40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : Makes:-Jaquar/Hindware/Cera W.C. pan with ISI marked white solid plastic seat and lid "

Providing and fixing Under Counter wash basin,with 32 mm Waste Coupling and other allied accessories including cutting and making good the walls wherever required:- a) White Vitreous China Under Counter Wash basin "

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm,including painting of fittings and brackets, cutting and making good the walls wherever required :510x1040 mm bowl depth 225 mm

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot restsMakes:-Jaquar/Hindware/Cera

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern,with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS :2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required :Range of two half stall urinals with 5 litre P.V.C. automatic flushing cistern

Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete,including painting of fittings and brackets, cutting and making good the wall wherever required :Size 600x450x200 mm

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing Rectangular shape 1500x450 mm

Providing and fixing toilet paper holder with Flap made out of C.P Brass Makes:- Jaquar/Hindware/Cera CP Brass

Providing and fixing C.P Brass Soap Dish. Makes:- Jaquar/Hindware/Cera

Providing and fixing health faucet with hose pipe for european water closet complete in all respect of approved quality Makes:- Jaquar/Hindware/Cera

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing CP brass towel rail complete with CP brackets fixed to wooden cleats with CP brass screws .Makes:- Jaquar/Hindware/Cera

Providing and fixing C.P brass bib cock with Auto closing System with Built in control Cock with Wall Flange of approved quality Makes:- Hindware/Jaquar/Cera 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm nominal bore

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge.

Providing and fixing soil, waste and vent pipes IS 13592 & fittings (IS: 14735 ) suitable to rubber ring joints , which includes bends, rubber ring, jointing, junctions, clean out plug , cowls, offsets, collar, M.S holder-bat clamps, access pieces, trap of self cleansing design .etc. complete including jointing.110 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-B

Providing and fixing soil, waste and vent pipes IS 13592 & fittings (IS: 14735 ) suitable to rubber ring joints , which includes bends, rubber ring, jointing, junctions, clean out plug , cowls, offsets, collar, M.S holder-bat clamps, access pieces, trap of self cleansing design .etc. complete including jointing.75 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-B

Providing and Fixing of Floor Traps 110 mm with double chrome plated Cover one Grated and one closed and all other fittings required.Makes:- Astral/SFMC/Finolex

Providing and fixing Polyethelene-Aluminium-Polyethelene (PE-ALPE) Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80 0C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes testing of joints complete as per direction of the Engineer in charge.Concealed work, including cutting chases and making good the walls etc.

1620 (20 mm OD) pipe

2025 (25 mm OD) pipe

2532 (32 mm OD) pipe

3240 (40 mm OD) pipe

Providing and fixing Polyethelene-Aluminium-Polyethelene (PE-ALPE) Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80 0C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes testing of joints complete as per direction of the Engineer in charge.Internal work (Exposed on wall)

2025 (25 mm OD) pipe

2532 (32 mm OD) pipe

3240 (40 mm OD) pipe

4050 (50 mm OD) pipe

5065 (65 mm OD) pipe

Providing and fixing Polyethelene-Aluminium-Polyethelene (PE-ALPE) Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80 0C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes testing of joints complete as per direction of the Engineer in charge.External Work

3240 (40 mm OD ) pipe

4050 (50 mm OD ) pipe

Providing and fixing unplasticised PVC connection pipe with brass unions:45 cm length_ 15 mm nominal bore

Cutting holes upto 30x30 cm in walls including making good the same with common burnt clay F.P.S.(non modular) bricks

Providing and Fixing of Thermal Insulation for Hot Water Lines made out of Flexible Elastomeric Foam of Closed Cells Structure Having a Thermal Conductivity of 0.038 W/m.K at 200 Deg C water Vapour Permeability of Cu.m 5000 as Required including accessories i.e Adhesives/Tape on all Joints as per the satisfaction of the Engineers Incharge.

1620 (20 mm OD) pipe

2025 (25 mm OD) pipe

2532 (32 mm OD) pipe

3240 (40 mm OD) pipe

4050 (50 mm OD) pipe

7590 (90 mm OD) pipe

Constructing masonary chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement: 4 coarse sand) with C.I. surface box 100x100x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement: 2 coarse sand:4 graded stone aggregate 20 mm nominal size) necessary excavation foundation concrete 1:5:10 (1 cenment:5 fine sand: 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement :3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design With F.P Bricks

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms,lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m

Providing and filling sand of grading zone V or coarser grade all-round the Composite Pipes in external work & lay dry brick over sand layer to protect the pipe.110 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-B

Supply, Installation of PVC Gully Trap of Size 110 mm Makes:-Astral/SFMC/Finolex

Making soak pit 2.5 m diameter 3.0 metre deep with 45x45 cm dry brick honey comb shaft with bricks of class designation 75 and S.W. drain pipe 100 mm diameter, 1.8 long complete as per standard design.with FPS Bricks

Constructing septic tank, of size 5.10 mx 1.7 mx1.80 m approx. height(Height to be fixed as per site requirement i.e. below invert level of last manhole (1.5 m water depth) , in B/W, 350/230 mm thick ( minimum) walls and 400 mm

Providing & fixing full way lever operated forged brass ball valve of brass body with forged brass hard chrome plated steel ball tested to a pressure not less than 16 Kg / sqcm with threaded / flanged joints complete with nuts, bolts, gaskets, washers etc.

65 mm Diameter

50 mm Diameter

40 mm Diameter

32 mm Diameter

25 mm Diameter

Providing and fixing on wall 35 LTRS Electric Geyser with ABS Body. Makes:- Racold/Hindware/Jaquar

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Supply,Installation,Testing and Commissioning of Open Well Submersible Pump(1 W ) with a Discharge of 75 LPM @Head of 35 Meters Complete with all accessories including header Pipes, allied materials and automatic Control Panel.

Providing, fixing supplying, termination & certification of CCTV/INTERNET/TELEPHONE networking . The item mentioned shall include the cost for laying Cat 6 UTP wire of in existing conduits for the wiring & it shall be such that each point has a dedicated single CAT 6 wire from the wall outlet to the patch panel.The rates quoted shall include the cost of termination of CAT6 cable in the wall sockets & patch panel including the cost of certification by network engineer using a penta-scanner , ferrulling of every point on both sides the contractor will have to provide the network certification in writing. Nothing extra shall be paid for on account of termination, crimping, certification etc. complete in all respects as desired by Engineer Incharge. The following items will be got exectued as underSupplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

RJ 45 Socket

Telephone socket outlet

Supplying and Fixing of Following sizes of PVC Conduit along with Accessories in surface/Recess including painting in case of surface conduit,cutting the wall and making good the same in case of recessed conduit as required.

25mm PVC Conduit

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.(1Run Cable)

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.2Pair

Supply, installation, testing and commissioning of Junction Boxes/DB-20 Pairs with Original Krone module and Back Mount Frame and have Lock -n- key, complete in all respect as per specification and desired by EIC

Supply, Installation, Testing and Commissioning of Semi managed 24 port POE , complete as per specification and as desired by EIC.

Supply & Erection of lockable 9/12 U rack with 5A strip and two fan for distribution, mounting of patch panels, hubs, switches etc,, complete as per specification and as desired by EIC.

Supply & Erection of CAT 6, 24 port Jack panel for termination of CAT6 cable,Testing & certification of the network with Omni/Penta Scanner of each Cable,

Supply & Erection of Cat-6, 1Mtr Patch Cords complete as per specification and as desired by EIC.

Supplying,Installation,Testing and Commissioning of 40 Inches Full H.D LED Display Monitor as per the Specifications attached.

Supplying of 16 Channel Network Video Recoder(NVR) as per the Specifications Enclosed with a Hard Disk Memory of 8 TB capacity.

Supplying,Installation,Testing and Commissioning of 2 Mega Pixel Full High Definition Weather Proof Networkable Bullet Camera.

Supplying and drawing of 12 Pair Single Mode Optical Fibre Cables in the existing surface/ recessed Steel/ PVC conduit as required.

Supply & Erection of Termination Box complete as per specification and as desired by EIC.

Supply, installation, testing and commissioning of 20 Pair jelly filled armoured cable of 0.5mm of each Pair Telephone Cable in the existing surface/ recessed steel/ PVC conduit, complete in all respect as per specification and desired by EIC

FIRE FIGHTING

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges,tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required

25mm dia

80mm dia

100mm dia

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :

Single headed Gunmetal

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

100mm dia

80mm dia

Supplying and fixing orifice plate made out of 6 mm thick Stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :(GUN METAL)

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red,conforming to IS 884 complete with the following as required.20 mm nominal internal dia water hose thermoplastic(Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle.Drum and brackets for fixing the equipmets on wall.Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket(30M)

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :(4 way_150 mm dia M.S pipe

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required

Providing and placing on terrace (at all floor levels) polyethylene water storage tank(5000 Ltrs), ISI : 12701 marked, with cover and suitable lockingarrangement and making necessary holes for inlet, outlet and overflowpipes but without fittings and the base support for tank

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required ( GUN METAL)

Providing and fixing Weather proof hose cabinets for yard hydrant fabricated from 16 g MS sheet with full glass door and locking arrangement, suitable to accommodate one hydrant valve, 2 nos.15m long hose, 1 No branch pipe and one fireman's axe. The cabinet shall be painted with one coat of primer and finished stove enamelled "Fire Red", "Fire Hose" written on front including suitably mounted on a raised masonry platform as required. (Approx 0.75mx0.6 mx 0.25 m).

Providing and fixing standard fireman's axe with heavy insulated rubber handle conforming to IS: 926 complete

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required (100mm dia)

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange(100mm dia)

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Providing, installation, testing and commissioning of Pressure Guages

Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) (a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520 b) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure,horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325.(c) M.S.fabricated common base plate, coupling, couplingguard, foundation bolts etc.as required.(d) Suitable cement concrete foundation duly plasteredand with anti vibration pads.(450 lpm at 35 m Head)

ELECTRICAL Works

Wiring for light point/ fan point/ exhaust fan point/ call bellpoint with 1.5 sq.mm FRLS PVC insulated copper conductorsingle core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, uitable GI boxand earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.(GROUP C)

Wiring for Light /Power Plug with 2 x 4 sq.mm FRLS PVC Insulated Copper Conductor single core cable in surface/Recessed medium class PVC Conduit along with 1 No. 4 sq.mm FRLS PVC Insulated copper conductor single core cable for loop earthing as required.

Wiring for Circuit/Submain Wiring along with earth Wire with the following Sizes of FRLSPVC insulated copper conductor,single core Cable in surface/Recessed medium class PVC conduit as required.

2 X 2.5 SQ.MM + 1 X 2.5 SQ.MM Earth Wire

14 X 16.0 SQ.MM + 2 X 6.0 SQ.MM Earth Wire

4 X 4 sq. mm + 2 X 4 sq. mm earth wire

4 X 10 sq. mm + 2 X 6 sq. mm earth wire

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings)

Supplying and fixing following modular switch/socket on the existing modular plate and switch box including connections but excluding modular plate etc as required

5/6 amps switch

3Pin 5/6amp socket outlet

Supplying and fixing modular blanking plate on the existing modular plate and switch box excl.modular plate as required

Supplying and Fixing suitable size G.I box with modular plate and cover in front on surface or in recess,including providing and fixing 6 pin 15/16 amps modular socket outlet and 15/16 amps modular switch,connection,painting etc. as required.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing 30 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 A "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32 A 240 V "C" curve DP MCB complete withconnections, testing and commissioning etc. as required.

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, onsurface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

4 way (4 + 12), Double door

6 way (4 + 18), Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board ofsheet steel, dust protected, duly powder painted, inclusive of200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) asrequired . (Note : Vertical type MCB TPDB is normally usedwhere 3 phase outlets are required.)8 way (4 + 24), Double door

Supplying and fixing following way, single pole and neutral,sheet steel, MCB distribution board, 240 V, on surface/ recess,complete with tinned copper bus bar, neutral bus bar, earthbar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)16 way, Double door

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required

Supplying and fixing following rating, double pole, (single phaseand neutral), 240 V, residual current circuit breaker (RCCB),having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 5amp to 32amp rating 240 volts "C series ,minature circuite breaker of following poles in the existing MCB DB complete with the conections testing and commisssioning etc as required

Single pole

Triple Pole and Netural

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminalspreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required(100 A,30KA,FPMCCB)

Supply and Fixing Single Pole Blanking Plate in the Existing MCB DB complete as Required

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.(Earth pit chamber (300mm x 300mm) with CI cover for the above)

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

SITC of pre-wired Surface Mounted LED Ceiling 4 ftr 1 x 36 W Fitting including connections with 1.5 sq.mm FR PVC insulated copper conductor single core cable and earthing etc as required made out of seamless Profile extruded Aluminium/Poly Carbonate Batten with an efficient diffuser to illuminate spaces.(Wipro LL22-511-XXX-65-G1***) .

SITC of pre-wired Surface Mounted LED Ceiling Light 18 W with Minimum 100 Lm/Watt Efficacy made out of Pressure die cast Aluminium Housing for effective Thermal Management and High Transmission Factor including connections with 1.5 sq.mm FR PVC insulated copper conductor single core cable and earthing etc as required.(Wipro LD 06-221-XXX57WSM)

SITC of Ceiling Fan,Capacitor type suitable for low voltage operation including wiring the down rods of standard length(Upto 30 cm)with 1.5 sq.mm FR PVC insulated,copper conductor,single core cable including providing and fixing phenolic laminated sheet cover on the Fan Box etc as Required.(1200 MM SWEEP(5 STAR)]

Supply of AC 230/250 Volts, 50 Hz exhaust fan with louveres of Following Sizes including connection etc. complete as required(300mm)

OUTGOING Adj. TMR Based MCCB 100 Amps FP Icu=Ics=100% Breaking Capacity 36 KA with Extendable ROH(05 Nos) Adj. TMR Based MCCB 63 Amps FP Icu=Ics=100%Breaking Capacity 36 KA with Extendable ROH (06 Nos) Adj. TMR Based MCCB 40 Amps FP Icu=Ics=100% Breaking Capacity 36 KA with Extendable ROH (02 Nos) Adj. TMR Based MCCB 25 Amps FP Icu=Ics=100% Breaking Capacity 36 KA with Extendable ROH (06 Nos) D.P M.C.B 63 A 10 KA(04 Nos) Indicating Lamps ON OFF TRIP( 19 Nos Load Bearing Members to be made out of 2.0 mm CRCA Sheet Partitions to be made out of 1.6 mm CRCA Sheet Gland Plates to be 3.0 mm Thick.

Supplying and laying of following size DWC HDPE pipe ISI markedalong with all accessories like socket, bend, couplers etc.conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required.200 mm dia (OD-200 mm & ID-175 mm nominal)

Supplying and Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in groundin Existing DWC Pipe including excavation, sand cushioning, protective covering and refilling the trench etc as required(.3.5 C X 300 Sq.mm A2XFY)

Supply and Making end Termination with Brass Compression Gland and Aluminium Lugs for the Following Sizes of PVC insulated and PVC Sheathed/XLPE Aluminium Conductor Cable of 1.1 KV Grade as Required (Comet)(3½ X 300 sq. mm (70mm)

Supply,installation with foundation as per approved Drawing 11 Mtr SP-56 S.T 410 Pole

Supply,installation of Structural Steel as per Standard Approved Drawing

Supply,Installation and Commissioning of 11 KV Air Break Switch(200 Amps).

Supply,Installation of 11 KV L.A 10 ka (Station Class).

Supply,Installation of 11 KV HG Fuse Unit .

Supply,Installation of Disc Insulator(B&S)70 KN suitable for 100 sq.mm Triple AAAC.

Supply and Installation of B&S Hardware Fittings.

Supply and Installation of 100 Sq.mm AAAC Triple AAAC.

Supply,Installation of 11 KV Pin Insulator suitable for 100 sq.mm Triple AAAC.

Supply and Erection of 150 mm Dia. Heavy Class G.I Pipe for the Cable Protection.

Supply,Installation and Commissioning of 11 KV Trivector Meter with suitable size Out door Type combined C.T and P.T's of 5/1A Accuracy Class 0.5 S Burden 100 VA 11 KV/Root3/110 V /Root3

Supply, Installation Testing and commissioning of 200 KVA Copper Wound Transformer with the Following Specifications:Frequency :-50 Hz+/-3 Hz No. of Phases :-3 Input configuration:- ( HV) Delta Output Configuration:- ( LV) Star Vector Group:- Dyn 11 Cooling:- ONAN Max. ambient temperature :-50º C Max. oil temperature rise:- 45º C Max. winding temperature rise :-55º C HV side High voltage withstand test :- 28 KV LV side High voltage withstand test :- 3 KV % impedance at 75º C :-4.5% Mounting of cooling radiators :- Direct mounting on tank Tapping :-Off circuit tap changer shall be provided on HV winding in variation from +/-5% in steps of 2.5%. Induced over voltage withstand test applied on LV side :-0.866 KV induced on HV side :-22 KV Terminal Arrangement HV side Bare:- Bushing LV side:- Cable Box with Aluminium Bus bars for cable termination. Neutral:- To be Provided

Supplying and Laying of XLPE Insulated and PVC Sheathed Power Cable of 11KV/ 1.1 KV Grade of the following size direct in Ground including excavation,sand Cushioning,Protective Covering and Refilling the Trench as Required. 3 C x 50 mm² 11 KV XLPE insulated Aluminum. conductor PVC outer sheathed armoured HT Cable with Earth (A2XFY with Earth HT Cable).

HT CABLE TERMINATION :- The scope also includes after HT termination Electrical contractor has to perform the High voltage test as per IS, If test is Ok then proceed further.

Supply, Installation testing and commissioning of indoor type termination kit for 3 C x 50 mm² 11 KV XLPE insulated Aluminum. conductor PVC outer sheathed armoured HT Cable with Earth (A2XFY with Earth HT Cable).(Raychem make)

Supply, Installation testing and commissioning of outdoor type termination kit for 3 C x 50 mm² 11 KV XLPE insulated Aluminum. conductor PVC outer sheathed armoured HT Cable with Earth (A2XFY with Earth HT Cable).(Raychem make)