SPL REPAIR TO BLDG NO P-10 AT 1 DET HQ INT AND FS GROUP, PROVN OF TOILET AT RPSO COMPLEX AND 03 NOS OF MINOR WORKS UNDER GE (EAST) DELHI CANTT-10

Amount

Taking down Chowkats or frames from the opening of size not exceeding 1.5 sqm each with shutters (without taking off shutters from the frames) complete.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.5 sqm but n.exc 4 sqm each complete.

Dismantling wrought iron or mild steel work of any description complete.

Taking down cement plaster on brick or stone walls ceiling , etc including raking out of joints, hacking for key, ccrubbing down with water etc complete.

S & F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete.

Dismantling plain corrugated steel sheeting, any gauge, thickness, including , Nainital or similar pattern roof coverings sheet in any pattern & position of roof coverings.

Dismantling timber scantlings , posts, rafters, purlins etc 40 sq. cm and over in section, in any position, complete.

S & F Pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall , fixed with self tapping screws with bent to a curve (of any radius as per required) complete.

Excavation in post holes (or similar holes) in soft/loose soil each not exceeding 0.5 cum getting out, returning, filling in ramming earth or broken rubble in layers not exceeding 25 cm, watering and removing of surplus soil to a distance not exc 50m and making good surfaces complete.

M&L for PCC (1:3:6) type D-2 using 40mm graded stone aggregate as in foundation etc complete.

M&L hard core of broken stone gauge n.exc 63mm deposited spread and levelled in layers n.exc 15cm thick watered and rammed to a true surface complete.

S & F Factory Made single extruded WPC (Wood Polymer Composite) Solid door/window/Ceosetory windows & other frames/ chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers( wood powder/ rice husk/ wheat husk) and nontoxic additives ( max toxicity index of 12 for 100 gms) fabricated with meter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face & 1100 N Edge), min compressive strength of 58N/sqmm and resistance to flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed with MS Holdfast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engr in charge. Note: -For WPC solid door/windows frames, minus 5mm tolerance in dimension i.e. depth and width of profile dimension on plus side shall be acceptable but no extra payment on this account shall be made etc complete.

All same as per srl item No 12 here-in-before but double rebare Frames/ Chowkhat of size 65 x 150 mm etc complete.

S & F factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headedcounter sunk S.S screws,etc complete. (Note: stainless steel butt hinges shall be paid separately under relevant item).

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type fly proof wire mess door shutter of size 35 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge. (Note: stainless steel butt hinges, necessary S.S screws ad wire mess shall be paid separately)

S & F 100mm size butt hinges stainless steel complete.

S & F 150 mm size Stainless steel bright polished barrel tower bolts,for doors with bright bolt.

S & F for Fancy type Stainless steel bright polished handles oval type of size 150mm size, complete.

S & F in repair 250 mm long Stainless steel bright polished sliding door bolts, plate type, stove with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed to door complete.

S&F Floor door stoper of aluminium alloy body with hard drawn steel spring 140mm long.

M&L Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks, cooler stand and similar work con- forming to Fe.290.Gde-E-165

Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.5 m height made of (big series) frame 112 x 52 mm & sash 42 x 66 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.20 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh hall be paid separately). (Note: The unit rate quoted by contractor include all other connected accessories. Net Opening will be measured lor payment purpose and for uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.)

Supply and fixing factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.90 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Glass/ wire mess shall be paid separately). (Note: The unit rate quoted by contractor include all other connected accessories. Net Opening will be measured lor payment purpose and for uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.)

S & F Anodised aluminium frame for doors, windows, ventilators, partations, AC provision window frame with or without three track, three track window frame etc with Powder Coating (minimum thickness of powder coating 50 micron) with one or more rebates including joining cleat for fixing etc. complete. (Note : Design and pattern for any type window/door/ventilator etc frame as required as approved by GE )

S&F powder coated aluminium door shutters aluminium sections weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150 mm long ( 1 No.) ,aluminium tower bolt 100 mm long (2 Nos), suitable handle (1 No.),hinges type B-21 100 mm long (2no.) or fixing on floor door spring box etc complete.

S & F for Door closer Aluminium extruded section hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed

S & F for Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed

S&F Sheet glass, 5.5 mm thick ordinary quality, in squares, not exceeding 0.50 sqm in each pane including beading fixed nails complete.

S & F 3/4 mm thick aluminium composite panel sheet colour matching with aluminium door and frame fixed with aluminium partations, door, cupboard etc complete.

S&F stainless steel wire cloth, 0.36 mm nominal dia. of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or stainless steel wire staples complete.

S & F 4 mm thick figured glass , pin head type and glazed with oil putty in square n. exc 0.5 Sqm in each pane fixed complete.

M&L two coat of synthetic enamel paint (finishing coat) over one coat of primer to new steel surfaces of any description over 10 cm width or girth incl prepration of surfaces complete.

S&F Magnet ball catcher brass body with 8mm dia steel ball of approved quanity complete.

S&F 150mm Brass handle, cast type, polished bright complete.

S&F 18/20 inch (45 CM) telescopic Drawer Channel channels, rollers for smooth sliding of drawers modular kitchen etc complete. (Make : - Godrej/Hettich/IPSA)

S&F 75 mm size brass Cup board lock, 4 lever grade I of superior quality complete. (Make : Godrej/ Harrison/ Link)

S & F for Hettich soft closure hinges with all fittings at mounting plate of premium quality, fixed in door/cup board shutters complete. (Make : - Godrej/Hettich/IPSA)

M & L with fabrication & fixing to horizontal & vertical shelves/ partations /sides/ top/ bottom/back sides etc for Modular kitchen cabinate/ wardrobe/ cupboard/drawers made out of 17/18 mm thick HDHMR boards with white laminated colour on both sides, of approved quality including paste to all exposed edge by edge Banding Tape with provision of cabinet for keeping baskets/ drawers etc and including taking down old any type cupboards , shelves etc complete. (Design and pattern as approved by GE). (Make :Action tesa or equivalent)

M & L with Fabrication & fixing to front side /all exposed sides of Modular kitchen cabinate/ wardrobe/ cupboard/drawers made out of 17/18 mm thick HDHMR boards with glossy/mat colour laminate sheet on front face and all exoposed sides and white laminate on other face of approved quality and including paste to all exposed edge by edge Banding Tape with provision of cabinet for keeping baskets/ drawers etc, including aluminium G/C/J profile handls and stainless steel handle for front face as required including taking down old any type cupboards, shelves etc complete. (Design and pattern as approved by GE). (Make :Action tesa or equivalent)

Supply only Stainless steel basket (Perforated Cutlery Basket SS) of size 445mm x 485mm x 100mm made with suitable arrangement for fixing over telescopic channel 18 inches/ 20 inches in length two way extruded MS galvanised over rollers. (Make: Godrej Cat art No 3575 or equivalent in IPSA/Hettich).

Supply only for Stainless steel thali/plate basket of size 445mm x 485mm x 200 mm made of min 4mmdia stainless steel wire of approved quality with suitable arrangement for fixing over telescopic channel 18 inches/20 inches in length two way extruded MS galvanised over rollers. (Make: Godrej Cat part No 3441or equivalent in IPSA/ Hettich).

Supply only Stainless steel plain basket of size 445mm x 485mm x 200 mm made of min 4mmdia stainless steel wire and bottom of S S perforated sheet approved quality with suitable arrangement for fixing over telescopic channel 18 inches/ 20 inches in length two way extruded MS galvanised over rollers. (Make: Godrej Cat part No 3892, or equivalent in IPSA/ Hettich).

Supply only Stainless steel two shelf pullout basket of size 150 mm x 450mm x 430 mm made of min 4mmdia stainless steel wire and bottom of S S perforated sheet approved quality with suitable arrangement for fixing over telescopic channel 18 inches/ 20 inches in length two way extruded MS galvanised over rollers. (Make: Godrej Cat part No 2260, or equivalent in IPSA/ Hettich).

75 mm dia oval shape brass handle fancy type polished bright finish

M & L for 18 to 20 mm thick granite (of any type) work( table rubbed and polished) in jambs, pillars, window cills, cooking platforms , risers, steps etc and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite slab over and including 10 mm thick screed bed in CM 1:4 including rounding to edge of granite as per required and including dismantling of existing granite of any description including cement mortar bedding (but not backing) and rubbish off the premises complete.

S&F steel water tubing galvanised 15mm bore medium grade fixed to walls, under floors and on ceiling surfaces , including cutting chases , pipning in making good to facings where required and pointing in Cement mortar 1:3 for concealed water tubing etc and including taking up or down old steel tubing 15 mm bore and connecetions in any postion etc complete.

S&F steel water tubing galvanised 20 mm bore medium grade fixed to walls, under floors and on ceiling surfaces and including taking up or down old steel tubing 20 mm bore and connecetions in any postion etc complete. (Note : Pipe work executed in shaft area and roof top upto the 10 story building also)

S & F in repair 110 mm PVC (SWR) pipes single socketed in any length with rubber ring joint laid in trenches or in floor or in wall completed all as specified and directed

S & F in repair 110 mm PVC (SWR) bends with acess door completed all as specified and directed

S & F in repair 110 mm PVC (SWR) junction single, (Single T) equal or unequal with acess door completed all as specified and directed

S&F repair 75 mm bore PVC (SWR) pipes single socketed , in any length with rubber ring joints ,laid in trenches or in floor or in wall complete.

S & F in repair 75 mm PVC (SWR) bends with acess door complete.

S & F in repair 75 mm PVC (SWR) junction single, (Single T) equal or unequal with acess door complete.

S&F in repair 110 mm bore PVC(SWR) vent cowl complete.

S&F in repair 110 mm bore PVC(SWR) floor trap, plain with grating including jointing with solvent cement complete.

S&F in repair 75 mm bore PVC(SWR) floor trap, plain with grating including jointing with solvent cement complete.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished even and fair complete.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished even and fair complete.

M & L Rendering 5 mm thick on fair faces of concrete or concrete surface in ceiling in CM 1:3, finished even and fair complete.

M&L for vitrified Ceramic tiles, full body/double charged, 8 to 10 mm thick ( shade/ colour/ Design/ pattern as approved by GE) polished /matt finished size 600mm X 1200mm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick rendering in cement mortar (1:6) and after dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete.

M&L for vitrified Ceramic tiles, full body/double charged, 8 to 10 mm thick ( shade/ colour/ Design/ pattern as approved by GE) polished /matt finished size 600mm X 1200mm as in skirting/dado/vertical surface etc laid on 10mm thick cement plaster in CM (1:4) , set and jointed in neat cement slurry and pointed in white/coloured cement to match the shade of tiles and after dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete.

M & L Coloured non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) size 395 x 395 mm / 400 x 400 mm , in floors etc, set and jointed in neat cement slurry and pointed in white or Coloured cement to match laid over and including 15 mm thick avg screed bed in CM 1:6 etc and after dismantling floor, hearth or wall tiling with cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete.

M & L Coloured Glazed ceramic tiles size 600 x 300 x 7-8 mm thick, in vertical surface such as skirting, dados , etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match laidd over and including 10 mm thick rendering in CM 1:4 and after dismantling floor, hearth or wall tiling with cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete.

Demolition or cement concrete (unreinforced) in ground floors and pavings n. exc 15cm thickness (below or above ground level) complete.

M&L for 75mm thick plain cement concrete (1:4:8) Type D1 using 20mm graded aggregate in sub base of floor complete.

M & L for Machine pressed precast conctete interlocking paver block of any shape and size (Two colour combination) conforming to IS 15658-2006 of 60 mm thick, M-35 Grade laid dry in floor/path including 50 mm thick sand bedding layer complete.

M & L for OUT DOOR coloured ceramic chequered tiles 8 to 9 mm thick (square/rectangular) area of each tiles exceeding 0.06sqm but not exceeding 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete.

M & L 75 mm thick Cement concrete work as in plinth protection type C-1 , 1:3:6 (20mm graded aggregates) with finishing cement concrete surface even and fair complete.

S&F in repair Vitreous China squatting pan 'Orissa' pattern size 580 x 440 mm white, with integral foot rests with connection to trap , and to flushing pipe antisyphonage pipe provision of trap set in and including concrete etc complete including making good to floor complete.

S&F in repair Brass CP Basin mixer central hole for making hot and cold water fixed as per manufacturers manual with long shunk and cup washers, screwed both ends suitable for 15mm bore GI Pipe joints to GI pipes or unions, complete. (Make : Jaquar Continental CON-CHR-167KNB or equivalent in Marc/Kohler)

S&F in repair brass chromium plated wall mixture 3 in 1 system with L- bend provision for over head shower and suitable for 15mm bore GI pipe including three joints to steel pipes or unions and plugging and screwing to walls complete. (Make : Jaquar Continental CON-CHR-273KNUPR or equivalent in Marc/Kohler)

S&F in repair Brass CP sink mixer with swinging spout (wall mounted model with connecting legs & wall flangesfor making hot and cold water fixed as per manufacturers manual with long shunk and cup washers, screwed both ends suitable for 15mm bore GI Pipe joints to GI pipes or unions, complete. (Make : Jaquar Continental CON-CHR-309 KNM or equivalent in Marc/Kohler)

S & F in repair Vitreous China wash down pedestal pattern EWC, white and including with PVC (SWR) ' S' Trap/P-trap , including seat cover with connection to drain and to flushing pipe antisyphonage pipe, and making good to floor complete.

S&F in repair 10ltrs PVC valveless, syphonic ac-tion type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete.

S & F in repair PVC connections 15mm size with PTMT nuts of length 600 mm.

S & F in repair full pedestal pattern wash hand basin with pedestal , size of basin 58 × 43.5 × 82.5 cm as approved by GE including brakets , chromium plated brass waste coupling , waste pipe etc complete all as specified and as directed. Make : HindwareTango Full Pedestal Wash Basin Cat part No. 10086 and equivalent in jaquar /Parryware)

S & F 32/40mm spring type PVC waste pipe fixed toWHB and sink (Note minimum length of each pipe should not be less than 0.80RM), fixed in repairs, complete.

S & F in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 45 cm long complete. (Make - Jaquar/ Marc/ Kohler/Prayag)

S & F in repair 20 mm bore Gun metal, globe or gate valves, with iron wheel head / leaver arm, screwed both ends for iron pipe and fixed

S & F in reapir CP shower rose fancy type 150 mm x 150mm size with 300 / 600 mm long shower arm fixed to 15mm bore pipe, complete. (Make - Jaquar/ Marc/ Kohler)

S & F in repair 15 mm bore bib tap (long body) ,fancy type chromimum plated screwed down high pressure with crutch/ butterfly handle/quarter turn handle etc suitable for 15mm bore steel tubing complete. (Make - Jaquar/ Marc/ Kohler)

S & F in repair 15 mm bore two way bib cock with wall flange cast copper alloy , fancy type , chromium plated, screwed for iron pipe or for brass ferrule complete all as specified and directed. Make : Jaqaur Cat Part No. ARI-39041 or equivalent Marc/ Kohler)

S&F in repair 15mm quarter turn brass angle valves, chromium plated cast copper alloy, polished body screwed down, high pressure,suitable for 15mm bore steel tubing complete. (Make - Jaquar/ Marc/ Kohler)

S & F in repairs Sheet glass corner shelf assembly consisting of 5.5mm thick sheet glass Min size 300 mm x 300 mm with chromium plated bracket guard and railing complete. (Make - Jaquar/ Marc/ Kohler)

S&F in repairs Hand Shower (Health Faucet) with 8 mm Dia, 1 Meter Long Flexible Tube & Wall Hook completed all as specified Make : Jaquar Cat part No. ALD-CHR-573 and equivalent in Marc/ Kohler)

S & F in repair Towel Ring Round with Round Flange fixed in positon with and including chromium plated brass screws and wooden/plastic cleats, complete all as specified and as directed. Make : Jaquar Cat part No. ACN-CHR-1121BN and equivalent in Marc/ Kohler)

S&F in repairs of CP towel rail 600mm long fixed with and including chromium plated brass screws and and wooden/plastic cleats (minimum weight 190 gms) fixed on walls, complete. (Make - Jaquar/ Marc/ Kohler)

S & F in repair SS soap dish, fixed in repairs, complete all as specified and as directed. (Make - Jaquar/ Marc/ Kohler)

S&F in repair sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm®

S & F in reapir stainless steel kitchen plate rack minimum size 900 mm x 750 mm x 200 mm including fixing on wall etc

S & F in repairs stainless steel Curtain Rod 25 mm dia with holders fixed to wall with finials and bracket etc in required size for doors and windows openning complete all as specified and as directed.

M & L for preparation of new surface decorated brick/concrete/ plastered or unplastered surfaces of walls, pillars, cornices by brooming down etc and applying three coats of white wash complete all as specified and directed

M & L for preparation of new surface decorated brick/concrete/ plastered or unplastered surfaces of ceiling surface by brooming down etc and applying three coats of white wash complete all as specified and directed

M & L for 2mm thick wall care putty on new/old any type of surface of wall/ ceiling including sand papering thus making surface even & smooth , complete all as specified and directed

M & L for preparation of new surface decorated brick/concrete/ plastered or unplastered surfaces of walls, pillars, cornices by brooming down etc and applying two coats of Oil Bound Distemper over a coat of interior primer complete.

M & L for preparation of new surface decorated brick/concrete/ plastered or unplastered surfaces of on celling surafce and applying two coat of oil bound distemper over a coat of interior primer etc complete.

M & L for preparation of new/old external surface decorated brick/concrete/ plastered or unplastered surfaces of walls, pillars, cornices by brooming down etc and applying a layer water proof wall care putty, again sand papering thus making surface even & smooth and applying two coats of weather proof exterior acrylic emulsion paint premium quality over a coat of exterior primer complete all as specified and directed. Allow 6-8hrs to dry the surface for painting of subsequent quotes complete.

M&L 12 mm thick white color GRG (Glass Fibre Reinforced Gypsum) Semi Perforated false Ceiling Tiles, Micro Tegular & Tegular edged, Size 595mm X 595mm, Fire Resistance BS-476-4:1970 (Certified), Humidity Resistance (RH) (Certified),including necessary GI frame/ GI T , cross , wall angle etc false ceiling grid (Ceiling Suspension System) in High Quality Zinc Coated Galvanized Iron with Pre Painted Hot Pressed White G I Coil including centre to centre Hangers 6 mm dia. G.I. rod fully threaded (upto 1000mm long) fixed to roof slabs with galvanised M-6 desh fastener 50 mm long including galvanised MS L-type level adjuster 85 x 25 x 25 x 2 mm etc including dismantling of walls and celing existing old board (fibre pulp insulation etc)or insulation boards/slabs/blanks any thickness including cover fillets etc. complete all as specified and directed.

M&L PVC hollow wall panelling 7 to 8 mm thick wood grain teak finished (colour and design as approved by GE) prelaminated inclusive of fixing on to wall including moulding end caps with L / U beading etc fixed with PVC sleeves and screws as required at site including dismantling of old wall panelling of any description complete. Note : Taking down existing any type of electric board sheet/ tube light/ LED / any fittings before fixing of panels and refixing the same after fixing the panels as required are included in the quoted rates by the contractor.

S & F Rotational moulded polyethylene water storage tanks 1000 lts capacity, triple layered (cylindrical vertical with closed top) hoisted and fixed in position with 20 mm dia PTMT ball valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed including taking out existing unserviceable overhead tank of any description complete.

M&L cutting, opening, through brick walls for doors & other opening, converted window in to door opening, cutting out defective brick work for under pinning cleaning, making good the disturb surfaces in CM 1:6 & removing rubbish from site not exc 50 mtr brick wall built in cement mortar complete.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement or cement lime morta including all quoins, arches,pillars, etc,

M & L for Brick work with sub class ‘B’ bricks, straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:6, complete all as specified and directed

M&L for providing cement concrete type 1:2:4 type B-0(12.5 mm graded agg ) as in roof kerbs or mud stops, filling of hold fasts and door frames, rounded or chamfered on edges complete all as specified.

M&L providing and applying the plaster with single component ready to use repair mortar capable of applying 20 mm average thickness in single layer and finishing with trowel with a bond coat : SBR polymer (@ 10% of cement weight) modified cementious bond coat @ 2.2 kg cement/Sqm of surface area complete. {Make: SMART CARE REPAIR MORTAR (ASIAN PAINTS) / RENDEROC SP-40 (FOSROC) / MONOTOP F122 THEXO TROPIC (SIKA)}. Note : (a) All materials shall be procured directly form manufacturer or their authorised dealer. (b) The application shall be executed on any type of surface and on horizontal/Vertical areas. (c) Full quantity of repair mortar shall be entered in MB as "NOT TO BE ABSTRACTED".

Providing and applying fibre reinforced elastomeric liquid water proofing membrane formulated with reinforcing acrylic fibers having Sun Reflectivity Index (SRI) of 105 on horizontal/vertical surfaces of roof/wall/chajjas in multiple coats @ 2.0 litre/sqm. Primary coat is self-priming coat of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1, damp proof : water) and other coats to be applied undiluted. The coating needs to be reinforced with 40 GSM geotextile, to sandwiched between 2nd & 3rd coat of coating. The application shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes complete in all respect as per the direction of Engineer-in-Charge. Make: Smart Care Damp Proof of Asian Paints or equivalent in SIKA/BERGER/FOSROC /STP. Notes: (a) The work shall be executed through authorised applicator of manufacturer only. (b) Authrised Applicator shall be approved by GE before starting of work. (c) All materials shall be procured directly form manufacturer or their authorised dealer. (d) Guarantee: The contractor shall furnish a written guarantee for the effectiveness of the water proofing treatment for a period of Eight years in favour of the GE. A sum equivalent to 2.5% (Two point Five Percent) of the cost of water proofing treatment shall be retained by the Govt from the contractor’s dues as security deposit. The contractor may, however, furnish a fixed deposit receipt in lieu from a Schedule bank pledged in favour of Garrison Engineer. (e) Full quantity of water proofing chemical / paint shall be entered in MB as "NOT TO BE ABSTRACTED".

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for etc complete.

M & L for RCC M-25 design mix (using 20 mm graded agg) as in slabs supported on walls, beams, and columns in floors , roofs, landings , balconies, canopies, deck slabs, counter slab and shelves etc complete.

M & L for form work to sides and soffits of suspended slabs such as roof slabs , landings , beams etc and similar work not exc 200 mm thick (horizontal or sloopping) for flat rough finished surfaces complete.

TMT mild steel bars 10mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for cloumns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete.

M & L for Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete.

Eacavation in trenches not exc 1.5m wide and not exc 1.5m in depth for foundation exc on for walls, shafts, manholes not exc 10 Sqm on plan or for laying pipes/cables etc and getting out in soft/loose soil complete.

Returing filling in incl spreading levelling watering and well ramming in layers not exceeding 25cm in soft or loose soil complete.

Removing excavatged matereials to a distance not exc 50m and depositing where directed at a level not exc 1.5m above the starting point in soils complete.

M & L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation, filling and mass concrete.

M & L for hardcore of broken bricks n exc. 63mm, deposited, spread and levelled in layers n exc. 15cm thick, watered and remmed to a true surface, complete.

M & L 4mm thick desginer false ceiling E- board ( Make : Everest or equivalent as approved by GE) in ceiling fixed with screw as per manufactures instruction, fixed with white powder coated galvanized iron grid with 24mm wide T-section exposed flanges comprising of main runner made from 0.33 mm thick galvanized steel sheet & size T-24x32 mm and spaced at 1.2m c/c securely fixed to the structural soffits by hangers at 1.2m of GI wire 2 mm dia fixed rawl plug, level adjusters and screws etc. The last hanger at the end of each main runner shall not be greater than 450mm from adjacent wall flush fitting of 1200mm long cross tee with (double stitching) to be inter locked between main runner at 600 mm c/c to from 600 x 600 mm modules, angle along perimeter wall shall be of 0.45mm thick galvanized steel of size 19 x19 mm of white colour all as per instruction complete all as specified and directed.

All same as per srl item No 112 here-in-before but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete.

M & L for RCC M-25 Design Mix using 20mm graded agg as in beams,lintle/plinth bands cantilevers, bressumers, lintel over 1.5m clear span supported on walls complete.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc.

M & L for Non-Skid coloured ceramic tiles 7-8mm thick (square/rectangular) area of each tiles exceeding 0.11 sqm but n.exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl 15mm thick screed bed in CM 1:6 complete.

M & L for glazed ceramic tiles in vertical surface 300x600x7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl 10mm thick screed bed in CM 1:4 complete.

M & L Vitrified ceramic tiles (double charge) size 600 x 600 x 8 -10mm thick (square/rectangular), ( shade/ colour/ Design/ pattern as approved by GE) ,as in skirting , dado , vertical surface etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles laid over and including 10 mm thick rendering in CM 1:4 etc complete.

S & F ready made floor/wall mounted Vanity box made of HDHMR board, both side laminated consisting of the following combination :- (a) Wash Hand Basin 810mm x 500mm. (b) Base Cabinet 780mm x 485mm x 460mm. (c) Side Cabinet 300mm x 250mm x 1800mm. (d) Mirror cabinet size 780mm x 160mm x 800mm. Make : Hindware - Cat Part No. 70089 or 70084. Make : Kohler : Cat Part No. K-31602IN-E63

S&F Brass CP Basin mixer central hole for making hot and cold water fixed as per manufacturers manual with long shunk and cup washers, screwed both ends suitable for 15mm bore GI Pipe joints to GI pipes or unions, complete all as specified and directed. (Make : Jaquar Continental CON-CHR-167KNB or equivalent in Marc / Kohler)

S & F Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement with brackets, flush pipe, grating and Union for discharge pipe with grating complete.

S & F Vitreous china single Piece floor mounted WC With PP Soft Close Seat Cover, Hinges, with cistern & Dual Flush Cistern Fitting, Fixing Accessories and Accessories Set, Size: 360x730x740 mm, S Trap- 300 mm including connecetion to drain pipe with all fitting and fixture complete all as specified and as directed. Make & Cat Part : Jaquar-Cat No. SLS-WHT-6851S300PP or equivalent in Marc / Kohler )

S&F bib tap fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe, 15mm dia, fancy type, cast copper alloy, chromium plated long body with flange complete. (Make: Jaquar/Marc/Kohler)

S & F Angle valve of CP high pressure screwed for iron pipe and fixed, complete. (Make: Jaquar/Marc/Kohler)

S & F PVC connections 15mm size with PTMT nuts of length 600mm complete.

S & F Soap dish, any type, fixed to plugs with chromium plated brass screws complete. (Make: Jaquar/Marc/Kohler)

S& F Brass chromium plated towel rack of size 600 mm x 350mm, fixed with brass screws, complete. (Make: Jaquar/Marc/Kohler)

S & F PVC (SWR) Floor/Nahani trap, plain dia of outlet 125mm, complete.

S & F Stainless steel Grating dome 125mm dia with or without hole for waste pipe, complete.

S & F for CP Push Cock fixing to urinal bowl 15mm size complete.

S & F Rotational moulded polyethylene water storage tanks 1000 lts capacity, double layered (cylindrical vertical with closed top) hoisted and fixed in position including 20 mm dia PTMT ball valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete.

S & F tubing 15mm bore medium grade, galvanised, ISI marked with all fitting and fixed complete to walls and ceilings or laid in floors complete.

S & F tubing 20mm bore medium grade, galvanised, ISI marked with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S & F for 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete.

S & F 32mm Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and as directed.

S & F 110mm dia PVC (SWR) pipes single socketed in any length with rubber rings joints fixed to walls or laid in floors as sanitary fittings, rain water pipes etc in any position complete.

S & F 110mm bore PVC (SWR) bends any radius complete

S & F Stack clamps out of 50 mmx 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for bore of pipe 100mm complete.

S & F 110mm PVC (SWR) vent cowl complete.

M & L for Coloured Machine pressed precast conctete interlocking paver block of any shape and size (Two colour combination) conforming to IS 15658-2006 of 60 mm thick, M-40 Grade with grey cement and pigment laid dry in floor/path complete.

M & L for Coloured Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry with grey cement and no pigment over and incl 15mm thick screed bed in CM 1:6 complete.

M&L Aluminium alloy powder coated standard hollow section for ventilotors as per approved sample and as per IS specifications, shutters weighting 0.55 kg/RM, rectangular frames of section 101.6mm x 44.45mm x 3.18mm weighing not less than 2.54Kg/RM including provision of 5.5mm thick tinted glass of superior quality including handles, tower bolt, hinges and all standard fittings complete.

S & F Precast SFRC square or rectangular manhole covers 75 mm thick with frame medium duty conforming to IS-12592 complete.

S & F Solid PVC door frame of size 50mm x 95mm made out of wood grain printed PVC sheet used reinforced with M.S. tube, suppling & fixing in opening as per specification & drawing complete.

S & F Factory Made Solid PVC Moulded Door Shutters 28 to 30 mm thick (stile:), with 2,4 or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front and back Face (wooden finish pattern), supplying & fixing in frame at site as per specification & drawing complete.

S & F Aluminum Anodised 150mm size barrel tower bolt with complete.

S & F 150mm size aluminum adodised handles complete.

M & L for 150 mm dia (internal dia) RCC hume pipe class NP -2 laid and and jointed complete with colleres complete laid in trenches and tested complete.

M & L for PCC 1:3:6 type C2 using 40 mm grade stone aggregate as in bed to drain pipe 150 mm bore incl forming cradles complte.

M & L for Plain Cement concrete 1:2:4, type B-1 using 20 mm graded crushed stone aggregates as in lintels up to 1.5 metre clear span, bed blocks, copings and the like including weathering, slightly rounded or chamfered angles & throating including provision of necessary formwork, complete including demolition of existing coping complete.

M & L for RCC M-25 design mix as in foundation, including rafts , footings , foundation beams, plinth beams; bases for columns, etc ; basement slabs, under- reamed piles and mass concrete complete all as specified and directed by Engr-in-Charge.

M & L for RCC M-25 design mix as in columns, pillars, piers, posts and struts etc complete all as specified and directed by Engr-in-Charge.

M & L for form work to sides of concrete foundation, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams: and similar works; vertical or to batter for flat rough finished surfaces complete all as specified and directed by Engr-in-Charge.

M & L for form work to sides of pillars, posts, struts, piers, columns and stanchions size of square, rectangular or polygonal for flat rough finished surfaces complete all as specified and directed.

M & L for form work to edges of concrete flats, treads breaks in floors , window cills , concrete railling, opening in concrete walls, floors and roofs RCC/PCC bands floors roofs n exc 20 cm wide and sides of RCC/PCC bands in walls , horizontal or slooping and similar work exc 10 cm and not exc 20 cm wide surface finished rough complete all as specified and directed.

Earth Soil spreading , levelling in layers n.exc 25 cm thick each layer with well ramming including watering as required under the floor complete all as specified and directed by Engr -in Charge. (Note :- Earth Soil available surplus soil from the excavation at ground )

M&L75 mm thick cement concrete type C-2 1:3:6 (40mm graded aggregate) as in sub base complete all as specified and directed.

M & L 25 mm Thick PCC type B-0 1:2:4 (12.5mm graded aggregate) as in flooring, under Tiles and etc all as specified and directed

S & F box type steel ventilators with shutter including hings , handels ,galzing bar without wire mesh etc all as specified and directed.

S & F 3 mm thick sheet glass , ordinary quality and glazed with oil putty in square n. exc 0.5 Sqm in each pane fixed complete all as specified and directed.

Material and labour for preparation of new surface decorated brick/concrete plastered or unplastered surfaces of walls, pillars, cornices by brooming down etc and applying two coat of cement base paint over a coat of cement primer etc complete all as specified and directed by Engr -in Charge.

S&F 15mm quarter turn brass angle valves, chromium plated cast copper alloy, polished body screwed down, high pressure,suitable for 15mm bore steel tubing complete all as specified & directed. (Make: Jaquar/Marc/Kohler)

S&F Pillar Cock Auto Closing System, cast copper alloy , fancy type , chromium plated, screwed for iron pipe and fixed complete all as specified and directed. (Make : Jaquar cat part No. PRS-031 or equivalent in Marc/Kohler)

S & F PVC connections 15mm size with PTMT nuts of length 450mm.

S & F Vitreous China wash down pedestal pattern EWC, white and including with PVC (SWR) ' S' Trap with connection to drain and to flushing pipe antisyphonage pipe, including sheet cover and making good to floor complete.

S&F Vitreous China squatting pan 'Orissa' pattern size 580 x 440 mm white, with integral foot rests with connection to drain and to flushing pipe antisyphonage pipe, brackets for flushing cistern ,PVC (SRW) 'P' trap including provision of cement concrete bedding etc complete.

S & F in repair Vitreous China Urinal, full stall type Urinal With Fixing Accessories, white and fixed complete all as specified and directed. (Make : Jaquar cat part No.URS-WHT-13261 or equivalent in Marc/Kohler)

S & F full pedestal pattern wash hand basin with pedestal , size of basin 58 × 43.5 × 82.5 cm as approved by GE including brakets , chromium plated brass waste coupling , waste pipe etc complete all as specified and as directed. Make : HindwareTango Full Pedestal Wash Basin Cat part No. 10086 or equivalent in jaquar /Parryware or equivalent Marc/Kohler)

S&F 10 Ltrs capacity PVC valveless symphonic action type flushing cistern white low level with inlet, ball valve float handle including bracket ,32mm bore PVC flush pipe complete.

S&F of CP towel rail 600mm long fixed with and including chromium plated brass screws and and wooden/plastic cleats (minimum weight 190 gms) fixed on walls, complete. (Make: Jaquar/Marc/Kohler)

S & F Sheet glass corner shelf assembly consisting of 5.5mm thick sheet glass Min size 300 mm x 300 mm with chromium plated bracket guard and railing complete. (Make: Jaquar/Marc/Kohler/Prayag)

S&F Hand Shower (Health Faucet) with 8 mm Dia, 1 Meter Long Flexible Tube & Wall Hook completed all as specified Make : Jaquar Cat part No. ALD-CHR-573 or equivalent in Marc/Kohler)

S & F Towel Ring Round with Round Flange fixed in positon with and including chromium plated brass screws and wooden/plastic cleats, complete all as specified and as directed. Make : Jaquar Cat part No. ACN-CHR-1121BN or equivalent in Marc/Kohler)

S & F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 45 cm long complete. (Make: Jaquar/Marc/Kohler)

providing and applying fibre reinforced elastomeric liquid water proofing membrane formulated with reinforcing acrylic fibers having Sun Reflectivity Index (SRI) of 105 on horizontal/vertical surfaces of roof/wall/chajjas in multiple coats @ 2.0 litre/sqm

S & F 15 mm bore two way bib cock with wall flange cast copper alloy , fancy type , chromium plated, screwed for iron pipe or for brass ferrule complete. Make : Jaqaur Cat Part No. ARI-39041 or equivalent in Marc/Kohler)

S&F brass chromium plated wall mixture 3 in 1 system with L- bend provision for over head shower and suitable for 15mm bore GI pipe including three joints to steel pipes or unions and plugging and screwing to walls complete. Make : Jaquar Continental CON-CHR-273KNUPR and equivalent in Marc/Kohler)

S & F 100 mm dia PVC floor trap , with ss grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4)

M & L S&F 110mm bore PVC (SWR) junction single (Single T) equal or unequal with access door complete.

M & L for Brick work with sub class ‘B’ bricks, straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:4, complete.

M&L for DWCPE (SN8) drain pipes of 150 mm bore laid in trenches and jointed and tested complete.

M&L for concrete bed to drain pipe including packing under and haunching against the side of pipes, 150mm bore, in cement concrete (1:3:6) type C-2 (using 40mm graded stone aggregate) after laying and testing of pipe complete.

M&L for 15mm thick plastering/rendering on brick work on concrete surfaces in cement mortar (1:3) mixed with liquid water proofing compound as per manufaturer's instructions finishing surfaces even and fair complete. (liquid water proofing compound shall be measured and paid sepretaely).

Supply only liquid water proofing compound complete all as specified & directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

S&F for Glazed ceramic matt finish coloured elevation tiles in vertical surface 450x350x7mm thick , set and jointed in neat cement slurry and pointed in coloured cement to match tiles over 10mm thick rendering in cm 1:3 complete.

M&L for steel gate Ornamental type/Grill work including hold fasts, pintels, stoppers running rails, bushes and all as CI decorative pieces, locking arrangement etc complete all as per design approved and as directed by Engr-in-charge work conforming to Fe-410-O etc complete.

Dismantling Single layer Mangalore pattern or similar tiles in roofing complete all as specified and directed

S & F for manglore pattern Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S&F in repair for 2mm thick fibre glass reinforced translucent plain sheeting fixed with coach screw and washer in roof, wall and other places as directed by Engineer in Charge

M&L for 40mm thick Damp proof course to horizontal or vertical surfaces including necessary formwork in cement concrete 1:2:4, type B-0 complete all as specified and directed.

M&L for Brickwork with sub- class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified.

50mm size cup board locks of brass including keys set, complete all as specified and as directed. (Make : Godrej/ Harrison/ Link)

S&F in repair sinks with drainage board made of stainless steel lmm thickkitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm ®

M&L for Coloured Glazed ceramic tiles/ vitrified tiles in floor / wall , reapir in patches , area n. exc 5 sq.m. including taking down and removing and cleaning old tiles, preparing beds and laying or setting, jointing with matching new tiles with existing tiles over rendering coat of 10mm thick rendering CM (1:4)/ 15 mm thick screed bed in CM 1:6 complete.

Taking down/ out carefully copper/aluminium point wiring for light/fan/bell/ sockets 5/15 Amps complete without accessories as switches, Sockets, holders, ceiling roses, light fitting regulators etc (to be measured and paid separately under relevent item of this Sch as S&F in repair and credit for these item given in credit schedule here-in-after) and making good the disturbed surface all as directed.

Material and labour of point wiring complete with 1.5 Sq mm (nominal area) FRLS PVC insulated sheathed and multistranded copper conductor cable ISI marked and including PVC concealed conduit ISI marked of size 20 mm dia medium grade and fittings such as tees, bends, elbow, and FRLS PVC insulated unsheathed 1.5 Sqmm copper conductor mulistranded earth wire, connecting to common earth dolly including MS Box with Plastic laminated sheet 3mm thick for fixing of switch/ socket/ fan regulator etc, cutting chases and making good disturbed surface in CM 1:3 to match with existing surface for one light / fan point controlled by one way switch complete all as directed.

All as per srl item No 206 here-in-before but for one socket outet point 5 amps on the same board.

All as per srl item No 206 here-in-before but for one socket outet point 5 amps on the independent board.

All as per srl item No 206 here-in-before but with 2.5 sqmm copper cable on independent board.

S & F in replacement switch piano, flush type, single pole one way 5/6Amp complete all as specified & directed.

S & F in replacement socket, 2 in 1, 5/6A flush type complete all as specified & directed.

S & F in replacement socket 3 pin 5/16A, 5 in 1 flush type complete all as specified & directed.

S & F in replacement switch piano, flush type, single pole one way 15/16Amp complete all as specified & directed.

S&F in replacement Ceiling rose, insulated body, 3 terminal, 240 volts, 5 Amps complete all as directed.

S & F in replacement Fan regulator step type complete all as specified & directed.

Material and labour in replacement submain wiring complete with 2 x 4.0 sqmm (nominal area) FRLS, PVC insulated, unsheathed and multistranded copper conductor cable ISI marked, and 1 x 4 sqmm as earth wire in and including PVC conduit of size 20 mm dia and conduit fitting such as tees, bends, elbow, reducers etc complete all as directed.

Material and labour in replacement submain wiring complete with 2 x 10.0 sqmm (nominal area) FRLS, PVC insulated, unsheathed and multistranded copper conductor cable ISI marked, and 1 x 6 sqmm as earth wire in and including PVC conduit of size 20 mm dia and conduit fitting such as tees, bends, elbow, reducers etc complete all as directed.

S & F in replacement LED batten fittings 10Watts, cool/warm white complete all as specified and directed..

S & F in replacement LED battens fittings, 1x20Watts, cool/warm white complete all as specified and directed..

S&F in replacement of LED bulk head fitting 10 watt made of cast aluminium alloy with opal glass diffuser complete all as specified and directed.

Taking down fan, sealing cable end, dismantling blades and removing fan and blades to store complete all as specified and directed.

Refixing of ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and directed.

S & F of energy efficicent LED fittings 45W LED 6K suitable for builing security light pressure die cast aluminium roadway luminaire with high power LEDs and HF electronic driver complete all as directed.

Supply and fixing in street light fitting bracket, 01 mtr long made out of galvanized iron pipe of 25mm dia size light grade complete with nut, bolts, washer etc inclusive of two coat of synthetic enamel paint over one primer coat, complete all as directed.

Supply & fixing and provision of ventilating fan of ventilating fan of size 250m sweep of engineering plastic body including louver in existing wall making all electric connections complete all as specified and directed.

S&F in replacement of MCB DB conforming to IP 43 - IK 09 with double door, SPN 08 way, double door complete all as directed.

Supply and fixing in replacement of MCB 'B ' Curve type, 10 kA, 10 to 32 Amp, Single Pole with over load and short circuit protection complete all as directed.

S&F in replacement of Isolator SPN 40 Amp , 230 Volt ,all connections complete all as specified and as directed.

Supply and fix electric water heater, storage type steel tank with inner glass linear with heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve,NRV ,fastner etc.

Supply and fixing ceiling fans complete with blades, down rods, and accessories, 230 V, 1200mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor(BLDC) including taking down of old u/s c/fan & deposited to MES store yard.Make -Crompton/Havells/Bajaj

Earthing complete with galvanised steel plate electrode 600 x 600 x 6 mm thick, buried directly in ground (earth pit not less than 2.25m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level , connected to and including galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, washers protected by and including 15 mm bore GI Pipe “light grade” and connected to main test point as directed and including concrete pit in PCC(1:3:6) type C1 precast RCC M-25 (design mix) precast cover slab (54 x 54 x 5 cm) duly reinforced with and including 8 mm dia TMT steel bars @ 150 mm C/C both way, one lifting handle made of 8 mm dia TMT bar embedded in precast cover slab, funnel, wire mesh, 20 mm bore GI medium grade pipe for watering, charcoal and salt in alternate layers, including necessary excavation and earth work any type of soil complete all as specified and shown in electrical plate No. 5 of SSR Part –I including testing on completion complete all as specified and directed.

Material and labour of point wiring complete with 1.5 Sq mm (nominal area) FRLS PVC insulated sheathed and multistranded copper conductor cable ISI marked and including PVC concealed conduit ISI marked of size 20 mm dia medium grade and fittings such as tees, bends, elbow, and FRLS PVC insulated unsheathed 1.5 Sqmm copper conductor mulistranded earth wire, connecting to common earth dolly including Metal Flush Box, Cover plate with frame for mounting of modular switch/ socket/ fan regulator etc, cutting chases and making good disturbed surface in CM 1:3 to match with existing surface for one light point exhaust fan point controlled by one 1-way switch complete all as directed.

All same as per srl item No 232 here-in-before but for one socket outlet point 5 amps on the same board.

All same as per srl item No 232 here-in-before but for one socket outlet point 5 amps on the independent board.

All same as per srl item No 232 here-in-before but for one light point controlled by two 2 way switches

All as per srl item No 232 here-in-before but for with 2.5 sq mm cable on independent board.

S&F of Modular switch 6 Amp, 1 way, 1 module size complete all as directed.

S&F of Modular switch 6 Amp, 2 way, 1 module size complete all as directed.

S&F of Modular switch 16 Amp, 1 way, 1 module size complete all as directed.

S&F of Modular socket 6 Amp, 2 in 1, universal type, 2 module size complete all as directed.

S&F of Modular socket 6/16 Amp multipurpose, 2 module size complete all as directed.

S&F of Ceiling rose, insulated body, 3 terminal, 240 volts, etc complete all as directed.

Supply and fixing of Distribution Board double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, surface mounting, SPN 8 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc and making all necessary connections complete all as directed.

Supply and fixing of MCB C Curve type, 10 kA, 10 to 32 Amp, Single Pole with over load and short circuit protection complete all as directed.

Supply and fixing of isolator 63 Amp, SPN type complete all as directed.

Supply and fixing of LED mirror light fitting 10 watt, cool/warm white and making all electric connections complete all as directed.

Supply and fixing of LED tube light fitting, 20 watt. with and including all electric connections complete all as specified and as directed.

S&F ventilatiing fan with engineering plastic 200mm sweep 230 volt AC with & including louvers and all fixing arrangements complete all as specified & directed.

Material and labour of LT underground cable XLPE insulated, PVC Sheathed armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 6 sq. mm 2 core ISI marked including all connections with thimbles of suitable size, complete all as directed.

M&L for sand cushioning to under ground cable provided with layers of snad(8 cms deep before laying the cable and 15 cms deep after laying) complete allas specified and directed at site by Engineer-in-Charge.

Supply and laying burnt bricks class - B for protection of cable complete all asspecified and directed at site.

Material and labour submain wiring complete with 2 x 4.0 sqmm (nominal area) FRLS, PVC insulated, unsheathed and multistranded copper conductor cable ISI marked, and 1 x 4 sqmm as earth wire in and including PVC casing caping of size 20 mm min, heavy duty double lock, and casing fitting such as tees, bends, elbow etc complete all as directed.

S & F switch piano,flush type single pole one way 15 Amp complete all as directed.

S & F socket outlet ,3 pin ,15Amp,flush type complete all as directed.

Supply and fixing wall mounted fan 400mm sweep, with step regulator 230 volt , Make-Bajaj Code-250542/Usha/Havells/CG complete all as specified & directed.

M & L XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 10sqmm 2 Core specified and directed at site by Engineer-in-Charge.

S & F switch piano,flush type single pole one way 5 Amp complete all as directed.

S&F of MCB, SPN,32 Amp, C curve type 10 KA, 240Volt.Make :INDOASIAN/ Legrand/Siemens

K S CONSTRUCTIONS (BID ID -3165380)

Vipul Construction (BID ID -3165534)

Gaurav India Corporations (BID ID -3168397)

Akhil Enterprises (BID ID -3165562)

tarun construction co (BID ID -3165185)