PROVEN OF BATHROOM, TOILET, URINAL POT, SOAK WELL AND GARBAGE PIT NEAR BLDG NO T-331 AND SPL REPAIR TO BLDG NO T-43 (A COY OR LIVING) AT HASIMARA MIL STATION AND SPL REPAIR OF ROOF TREATMENT OF KENDIYA VIDYALAYA BUILDING AT COOCH BEHAR UNDER GE(S) B

Amount

Dismantling of Plain or corrugated steel sheeting,any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed

Dismantling timber scantlings 40 sq. cm and over in section, in any position complete all as specified and directed

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed

Demolition of reed, lathing, single or double, including battens and plaster or chicken wire lathing complete all as specified and directed.

Demolation Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, complete all as specified and directed.

Taking down Chowkhats or frames not exc. 1.5 sq. m each but with shutters (without taking off shutters from the frames) complete all as specified and directred

Taking down Chowkhats or frames exc. 1.5 sqm but not exe 4.00 sqm each but with shutters (without taking off shutters from the frames) complete all as specified and directred

M&L for PCC 1:4:8 Type D2 using 40mm graded stone aggregate in foundations, filling and mass concrete complete all as specified and directed.

M&L for RCC type B1,1:1.5:3(Nominal Mix) using 20mm gradded aggregate as in founations , incuding raft footings,foundation beams, plinth beams, base for columns, etc basement slab, under remain piles and mass concrete complete all as specified and directed Note- Reinforcement and form work shall be measured and paid separately.

M&L for RCC type B1,1:1.5:3(Nominal Mix) using 20mm gradded aggregate as in beam, cantilivers, bressummers, lintel over 1.5 Mtr span and similar work complete all as specified and directed. Note- Reinforcement and form work shall be measured and paid separately.

M&L for RCC type B1,1:1.5:3(Nominal Mix) using 20mm gradded aggregate as in beam, chajjas and similar work complete all as specified and directed. Note- Reinforcement and form work shall be measured and paid separately.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, also splays between floors and beams, etc.complete all as specified and directed.

Formwork to chullah hoods, chajjas, troughs and similar items including edges etc for rough finished flat concrete surface complete all as specified and directed

Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and direted

Mild steel bars 5mm dia and over including 10mm dia as in stirrups , spacers and binders cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and direted

M&L Brickwork with fly ash bricks straight or curved on plan exc 6 m mean radius built in cement mortor 1:6 complete all as specified and directed.

Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 and painting one shop of zinck chromimum pimer paint including preparation of surfaces at contractor workshop before fabrication complete all as specified and directed

S&F MS steel Hollow section square/rectingular as in roof truss, purlin, rail etc complete using ERW or induction butt weldedhollow section conforming to I. S.1161- 1979 grade St.-240 and painting one shop of zinck chromimum pimer paint including preparation of surfaces at contractor workshop before fabrication complete all as specified and directed

S&F rolled mild Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment of grade Fe410W (Gde E-250) quality A complete all as specified and directed.

S&F rolled mild steel in joist ,channel, angle or tee section fixed independentely, without conecting plates , etc (cut ordinary lengths i.e within 20mm of the length indicated ) of Fe 410-W ( Gde E-250) qualiy a complete all as specified and directed.

S & F Mild steel bolts. purpose made. with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut. Exc 30cm long complete all as specified and direted

M&L for external rendering 20 mm thick in two layer, first layer shall be of 10 mm thick CM 1:6 and second layer of finishing coat shall be 10 mm thick in CM 1:4 mixed with WPC as per manufacturer instruction by weight of cement on brick work or concrete surfaces of wall and finished even and fair complete all as specified and directed. Note-WPC shall be measured and paid seperately.

M&L 15mm thick rendering in cement mortar 1:6 on fair face of brick work or concrete surface finished even & smooth (without using extra cement) complete all as specified and directed.

S&F for pressed steel frames 125x60mm size for doors with one or more rebates including necessary lugs, hinges, lock strike plate, etc., complete all as specified and directed.

M & L for providing plain cement concrete type C-1, 1:3:6, (using 20 mm graded stone aggregate), as in copings, bed block for filing hollow space of steel chowkhats, fixing of hold fast, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and directed.

S&F 35mm thick second class hard wood rail and style Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

M&L second class Hard wood 30mm thick factory made Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, complete all as specified and directed.

S & F in stainless steel wire cloth 0.36 nominal dia wire & average width of aperature 1.40 mm fixed with stainless steel wire staples complete all as specified and directed

S & F Mild steel barrel tower bolts 150 mm long , stove enamelled black, with bright bolt and fixed complete all as specified and directed.

S & F Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate of 250mm long complete all as specied and directed

S&F Mild steel handles 150mm size cast type stove enameled black comlete all as specified and directed

S &F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring,fixed in floor over all length of cover plate 140mm complete all as specified and directed

Demolation of un-reinforced cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for 100mm thick of Cement Concrete 1:4:8 type D2 using 40mm graded stone aggregate as in sub base complete all as specified and directed.

M&L PCC (1:2:4) type B1 using 20mm graded stone agg as in base flooring 40mm thick surface finished even and rough to receive the topping layer complete all as specified and directed

M&L for non skid coloured joint free ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exc. 0.18 Sqm but n. exc. 0.38 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match as in floor including 15mm thick screed bed in cement mortor 1:6 complete all as specified and directed.

M&L for non skid coloured joint free ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exc 0.18 Sqm but n. exc. 0.38 Sqm, in skirting/dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match as in Vertical surface including 10 mm thick screed bed in cement mortor 1:4 complete all as specified and directed.

M & L for preparing new Plastered surfaces of walls on applying two coats of Acrylic distemper over a coat of 1mm wall care putty complete all as specified and directed.

M&L for preparing of newly plastered surfaces of wall including cornices etc by brooming down applying two coats of antifungal exterior acrylic emulsion paint over a coat of acrylic primer complete all as specified and directed.

M&L for preparation of newly or previously untreated surfaces of wood and based surfaces of any description, over 10cm width or girth and applying Two coat of synthetic enamel paint over a coat of pink primer complte all as specified and directed

M&L for preparation of newly or previously untreated surfaces of new steel surfaces of any description, over 10cm width or girth and applying Two coat of synthetic enamel paint over a coat of red oxide complete all as specified and directed

M&L for high tensile 550 MPA yield strength Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering The sheet shall have a hot dip metallic zinc aluminium alloy coating of zinc 43.5%, aluminium (55%)and silicon (1.5%) with total mass coating of 150 gms/sqm on both sides. Covered width will be 1020mm and sheet length as per site requirement. The profile is having return leg for proper side lap. The sheet shall be fixed using self drilling/self capping screws with EDPM seal complete all as specified and directed.

All as per item No- 42 here- in- above but Plain sheets as in ridges/ hips / valley/Eaves and Eaves board - ditto --

S&F 4mm thick non-Asbestos fibre cement building board( E-board) false ceiling with board of size 600x600mm with powder coated GI snap grid frame work including cutting holes in brick wall built in cement mortar & making good in cement concrete 1:2:4 type B0 Cement mortar 1:3 complete all as specified and directed including all necessary drilling and necessary arrangement to fix electrical items as under:- (a) 27x27x0.55mm thick GI angle powder coated duly plugged @ 600mm centre to centre along perimeter of wall. (b) 25x25x0.55mm thick GI tee powder coated as main and cross runners suspended with 1.6mm dia GI wire suspenders(n.exc 1.2mtr length) with adjustable clamps and dash true fastners plugging in RCC slab/A.I Runner of slopped roof placed @ 600mm centre to centre from perimeter of wall. (c) Fixing of 4mm thick non-Asbestos fibre cement building board( E-board) false ceiling with board of size 600x600mm of approved texture and finished complete with two coats of oil based distemper over a coat of alkali resistance primer on ceiling. NOTE: The complete ceiling work shall be done as per manufactures instruction and as directed.

M&L for 75mm thick plain cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection and footpath finished even and smooth without using extra cement, including making joints to the full depth of PCC at every 3 metres and at every change of direction and filling the same with & including bitumen and sand 1:2 by weight complete all as specified and as directed.

M&L Plain Cement Concrete Type B2 1:2:4 (using 40 mm graded stone aggregate) 75mm thick in floor laid in panels and finished even and smooth using extra cemnt including necessary form work complette all as specified and directed.

M&L for machine pressed ,pre-polished and chemically treated, smooth finished ,exterior graded coloured cement concrete Chequered tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed.

Excavation in trenches, n exc 1.5 mtr wide and n exc 1.5 mtr in depth for foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. n exc 10 Sqm on plan and n exc 1.5 mtr in depth and getting out in hard/dense soil complete all as specified and as directed .

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in any type of soil etc complete all as specified and directed

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed

Excavating in hard/dense post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm,complete all as specified and directed

M&L for Cement concrete Type B2 1:2:4 (40mm graded aggregate) in walls or retaining walls, any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases) complete all as specified and directed.

M&L for sand filling under floor or in foundation including watering and consolidation complete all as specified and directed .

M&L for broken stone or boulders hardcore of gauge exceeeding 63mm but not exceeding 100mm thick, deposited , spresd and levelled in layer ot exceeding 15cm thick, watered and rammed to a true surfaces completed all as specified and directed .

M&L for PCC 1:2:4 type B-0 using 12.5mm graded stone aggregate as in sub base flooring 25 mm thick surface finished even and rough to receive the topping layer completed all as specified and directed

M & L for preparattion of newly plastered surfaces of wall and applying three coat of white wash complete all as specified and diredted.

Plain Cement Concrete Type C1 1:3:6 ( Using 20mm graded sone aggregate) in fondation, filling and mass concrete complete all as specified and directed.

Taking down existing tarfelt including demolition concrete and roof padding like lime concrete, mud phuska , brick lime coba etc and cement plaster from roof surfaces and lowering and removing the same at location upto a distance of 3km incl roughening of old concrete suirface of roof by wire brushing and cleaning the surface to remove all loose dust etc complete all as specified and as directed.

M & L for 25 mm thick PCC 1:2:4 type Bo (Using 20 mm graded stone aggregate) mixed with integral Water Proofing Compound wherever required as directed and laid on RCC slab as base layer for roof treatment including roughing the top surface of concrete by using broom sticks while the concrete is green but excluding cost of Water Proofing compound complete all as directed .

M&L for 15mm thick screed bed or bedding layers in cement mortar (1:3) in order to maintain proper slope over existing roof surfaces for laying APP based polymeric membrane, finished even and smooth without using extra cement mixed with water proofing compound in top layer as per manufacturer instructions complete all as specified and as directed. (NOTE : Polymeric membrane & WPC shall be measured and paid separately under relevant item of this Schedule 'A').

M & L PCC (1:2:4) type B0 (12.5mm graded aggregate) as in roof kerbs, coping, slightly rounded or chamfered on edges, finished even and smooth on exposed concrete surface without using extra cement all complete as specified and as directed.

M&L for water proofing treatrment to Non accessible RCC roof slab, including parapet comprising with the following courses of treatment. (a) Applying a coat of bitumenous primer confirming to IS-3384 1965 @ 0.4 ltrs per Sqm over plastered surfaces of roof incl parapet surface and allow to dry. (b) Apply one coat of hot blown bitumen grade 85/25 as per IS -702-1988 @ 1.20 Kg/ Sq.M of Each coat applied over primer including cleaning of surfaces. (C) Supply and laying 3 mm thick polymeric water proofing membrane weight not less than 3.50 Kg/Sq.M with non woven polyester fabric weight not less than 160 gms per Sqm over area including overlapping 100 mm (Min) as per manufacturers instructions. (d) Applying evenly one coat of bituminous aluminium paint @ 150 Gms/Sq.M complete all as specifiedand as directed. Note :- (i) Laying APP bassed polymenic membrane shall be done torch on methed or as per manufacturer's instructions. (ii) A minimum over lap of 100mm and 75mm should be made at the end and sides of the polymeric membrane respectively and sealed all overlaps and joints as per manufacturer's instruction. (iii) The complete work shall be done under strict supervision of manufacturers technical representative as directed.

Taking down cement plaster on Brick wall or stone wall & ceiling of any description including racking out joints, hacking for key and scrubbing down with water etc complete all as specified and directed.

M&L for 10 mm thick plaster of cement mortar (1:4) rendering on fair faces of brick/concrete surface finishing the surface fair and even without using extra cement mixed with water proofing compound as per manufacturer instruction NOTE:- WPC will be measured and paid sparately

Supply only integral water proofing compound conforming to IS: 2645 - 1975 specification complete all as specified and as directed .

S&F in repair of rotational moulded,Three layer HDPE water storage tank of 500 ltrs capacity (Cylindrical vertical with closed top) ISI (IS 12701-1996) marked fixed in position on existing places complete all as specified including 02 Nos 20mm dia full threaded UPVC tank niple, 20 mm dia brass ball valve with epoxy coated Aluminium rod with high density plastic float ball( of minium weight 210 gms ) including fixing of inlet, outlet & overflow pipe etc, complete all as specified and as directed.

S&F in repair for 25mm bore Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed all complete as specified and as directed.

S&F in repair for 20mm bore Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed all complete as specified and as directed.

M&L for preparation new painted surfaces on wall and applying two coat of weather proof Acrylic exterior emulsion paint over one coat of primer of approved make and shade complete as specified and as directed.

Removing building materials and debris ( other than excavated earth) to a distance of 5 Km of outside MD land/KV SC including and dumpling /leveling at the destination complete all as specified and directed .

Taking up or down steel tubing 20mm and connections complete all as specified and directed .

Taking up or down steel tubing 25mm and connections complete all as specified and directed .

S& F 15 mm bore steel water tubes, medium grade, galvanised with all fitings and fixed to wall, complete all as specified and directed.

S& F 20 mm bore steel water tubes, medium grade, galvanised with all fitings and fixed to wall, complete all as specified and directed.

S& F 25 mm bore steel water tubes, medium grade, galvanised with all fitings and fixed to wall, complete all as specified and directed.

M&L for non skid coloured ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.06Sqm but n. exc. 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in whiter or coloured cement to match as in floor including 15mm thick screed bed or bedding layer in C:M 1:6 surfac finished fair and even for laying floor finishes complete all as specified and directed.

M & L for glazed ceramic colour tiles 450X350X 7 mm thick as on vertical surface of wall such as skirting, dado, riser etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile including rendering 10mm thick in cement mortor 1:4 approved by Engr-in-Charge complete all as specified and directed.

Solid PVC door frame of size 50x47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube, supplied and fixed incl fixing of hold fast as per specification and drawing complete as directed.

S&F of factory made solid panel PVC door shutter, 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails MS frame shall be covered with heat moulded plain clolur PVC `C' channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stile and plain clolur PVC sheets for top rail lock rail & buttom rail on either side and as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with slolvent cement, supplying & fixing in the frame at site as per manufactures instruction complete all as specifeid and directed

S&F 75 mm Aluminium steel butt hinges etc complete all as specified and directed.

S&F 100 mm long Aluminium anodised barrel tower bolts complete all as specified and directed.

S&F for sliding door bolt of 150mm long plate Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed

M&L for prepartion of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer with alkali resistance priming paint on plaster and other surfaces complete all as specified and directed.

M&L preparing newly plastered or unplastered surface of wall and applying two coats of Cement base paint over a coat of cement base primer complete all as specified and directed.

S & F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wallsor laid in trenches etc complete all as specied and directed

S & F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wallsor laid in trenches etc complete all as specied and directed

S & F 75 mm bore PVC (SWR) bends of any radius complete all as specied and directed.

S&F 110mm dia PVC bends of any radius access door complete all as specied and directed.

S & F 110 mm bore PVC (SWR) junction single (Single `T') equal or unequal with access door complete all as specied and directed.

S&F aluminium handle cast type anodiside of 150 mm size complete all as specied and directed.

S&F for 110/125mm PVC gully trap setting and jointing with solvent cement complete all as specified and directed

S & F for vitreous China squatting pan, 'Orissa' pattern, size 580 x 440 mm white with integral foot rest and 'P' or 'S' trap, including provision of lime concrete bedding, connection to trap and flushing pipe etc complete including making good to disturbed surfaces of floor to match with existing specifications as specified.

S&F Vitreous China urinals, Half stall type white with greating and union for discharge pipe complete including providingand fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement;etc complete all as specifed and directed .

S&F Vitreous china urinal partition white size 310x700 mm complete all as specified and directed .

S&F vitreous china wash basin, white, flat back, size 550x400m excluding taps, waste , chain & plug & porcelain stopper including brackets incl cutting for pinning in ends of bracketes or erecting stand and fixing and supply and waste pipe complete all as specified and directed.

S&F 10 ltr capacity PVC flushing cistern low level white colour incl PVC connection PVC flush pipe of reqd length complete all as specified and directed.

S & F 15mm bore PVC Connection with PTMT nut of length 450 mm complete all as specified and directed

S&F stop valves fancy type cast copper alloy, chromium plated with long shank and cup (concealed type) for 15mm bore pipe, screwed both ends including necessary fittings such as sockets for pipe or for union all complete as specified and as directed.

S&F 15mm bore pillar taps, cast copper alloy with capston heads, chromium plated, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly-nuts, screwed for iron pipe complete as specified and as directed.

S&F Bib taps ( Long Body) fancy type cast copper alloy, chromium plated for 15mm bore pipe, screwed for iron pipes or for brass ferrule all complete as specified and as dierected.

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with chomium plated bracket guard and railing 60 cm long complete as specified and as directed.

S& F 75 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed.

M&L 150mm Salt glazed stoneware drain pipes laid in trenches and jointed complete all as specified and as directed.

M&L Concrete bed 1:3:6 type C2 to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested in complete all as specified and as directed.

S&F factory made Z section steel ventilator with top hung shutter frame including projecting/ box type hinge with steel handle and steel peg stay complete with glazing bars , dovetailed or welded including a shop coat Red Oxide priming complete all as specified and directed.

S&F 3mm Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed

M&L for providing RCC 1:2:4 type B-1( using 20mm graded stone aggregate) as in precast cover slab and the like inclluding necessary formwork complete all as specified and directed.

M&L for soakage wells excavation, in any type of soil, foundation in PPC 1:3:6 walls of honey combed masonary with top ring of M25 concrete including intercepting chamber and and screen chamber made of brick masonary in CM, RCC cover slab in M25 / SFRC cover, interconnecting pipes of RCC / DWC complete filled with brick bats of size 2.4M X3.0 M effective depth complete all as specified and directed.

INTERNAL ELECTRIFICATION Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc for taking credit ( credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed.

M&L point wiring complete with FRLS PVC insulated unsheathed multistranded copper conductor of size 1.50 sqmm nominal cross sectional area single core drawn in and including 20mm dia 'heavy grade' PVC concealed conduits and fittings, including cutting chasing in brick wall n.exc 10cm width or girth(excluding ceiling surface), pressed steel concealed terminal switch boxes not less than 1.2mm thick of required size factory made duly painted inside and outside with two coats of black bituminous paint over one coat red oxide primer, 3mm thick plastic laminated sheet top cover (ISI Marked) fitted with chromium plated brass screws & washers complete including 1.50 sqmm nominal cross sectional area PVC insulated unsheathed multistranded copper conductor green as earth wire connected to earth dolly with all accessories including making good disturbed surfaces with CM(1:4) with treating the surfaces as per existing finishes complete all as specified and directed.

(a) One light point controlled by one way switch 5/6 amps.

(b) One ceiling/ Exhaut fan point controlled by one way switch 5/6 amps.

(c) One Socket out let 5/6 amps point on the same board

(d) One socket out let 5/6 amps point on the independent board

All as per item No 112 above but wiring with 2.5 sq mm single core copper conductor for one socket out let 15/16 amps point on the independent board complete all as specified and directed.

S&F socket 2 in 1, 5 Pin, 5/6 amps, white ivory finish flash type complete all as specified and directed.

S&F of socket outlet 2 in 1, 5 Pin, 5/15 amp, multipurpose 230 volt flash type complete all as specified and directed.

S&F switch piano flush type 5/6 amps single pole one way complete all as specified and directed.

S&F switch piano flush type 15/16 amps single pole one way complete all as specified and directed.

S&F ceiling rose, bakelite, surface type, 220/240 volts, three terminals complete all as specified and directed

S & F in repair Wall mounted LED Tube light fitting 18W, with extruded aluminium housing, with integrated LED driver complete all as specified and directed

S&F (in replacement) High Power LED street light fitting ,system wattage-45 Watt, Complies to IEC 60598 and IS 10322 with deep drawn aluminium Pressure die cast housing ,toughened glass cover with IP-66,CL-I protection,Integral electronic driver,Heat sink,Cast Aluminium pipe mounting attachment complete with LED lights and connecting the street light fitting using 2.5 Sqmm PVC insulated three core copper cable including taking down all as specified and directed.

M&L for sub main wiring with 3 run of 4.00 sqmm ( nominal cross section areas) PVC insulated unseated single core Cble of working voltage 1100 volts grade with standard copper conductor drawn in PVC rigid no metallic conduit complete All as specified and directed Note- Three run of sub main wiring cable alongwith 25mm PVC conduit pipe shalll be measures as one unit lenght

S&F Sheet metal enclosure for 8 way Distribution Boards (DB’s), double door, single pole & neutral with 200 amps rated bus bar, IP-43 protection suitable for fixing MCB"S/lsolators complete all as specified and directed.

S&F MCB, Single pole & neutral 5 to 40 amps, 240 volts, ‘C’ curve, 10 KA all complete as specified and as directed .

S&F MCB, Single pole, 5 to 32 amps, 240 volts, ‘C’ curve, 10 KA all complete as specified and as directed .

M & L for security light bracket made out of GI pipe light grade 40 mm dia 1.0 mtr length bent to shape and reduced to required size at top upto 1.2 mtr length by cutting, welding and well finishing including MS clamp of flat iron of size 25 x 5 mm suitable length 2 Nos complete with drilling, hole, fixing with nuts bolts and washers including painted with two coats aluminium paint over a coat of red oxide primer complete all as specified & directed.

Material and labour for earthing with GI earth plate electrode 600mm x 600mm x 6mm thick buried directly in ground vertically to depth not less than 2.25m below the ground level with top edge of earth plate at a depth not less than 1.5m below the ground level connected to galvanized iron wire 4mm dia earth lead by means of bolts & nuts,check nuts & washers made of galvanised steel, earth strip protected by and including PCC (1:2:4) type B1 precast RCC cover slab (M-15) reinforced with 8mm dia TMT bars 100mm center to center bothways including one handle made of 10 mm dia round bar, including necessary excavation and earthwork in any type of soil, 20 mm dia medium grade galvanized steel tube for watering with one end fixed with cast iron funnel and wire mesh, 15 mm bore medium grade galvanized steel tubing for drawing earth lead GI strip protection & common salt, charcoal in alternate layers etc. complete all as shown in EP No 3 of SSR Part 1 2009 and testing on completion complete including dismantling the existing unserviceable earthing complete all as specified and as directed.

S&F delux Fan electronic regulator AC 50 Hz rotary step whit/ivory finish complete all as specified and directed

Supply and fixing LED light fitting mirror type with high with high output diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed

DEEP NIRMAN

M/S I P GROUP

M/S. VINITA CONSTRUCTION

M/S BIJAY KUMAR SHIVA

M/S BISHAL ENTERPRISES

SHRI D P AGARWAL

M/s. MD IRSHAD