GE(S) BTD 19 OF 2024-25 COMPREHENSIVE MAINTENANCE BR AND EM REPAIR INCLUDING ATTENDING DAY TO DAY COMPLAINTS REPAIR REPLACEMENT OF JOINERY TANK CLEANING AND CERTAIN OTHER MISC WORK AND REPAIR TO CHAJA PARAPETS ETC OF CERTAIN BLDG OF ABDUL HAMID ENCL

Amount

Comprehensive maintenance for Carpentary work by attending day to day complaints of joinery related such as replacement of Builders hardware of doors, windows & cupboard and other Carpentary nature works like easening of door, windows and cupboards. Tightening of screws for tower bolt/Aldrop bolt/ stoppers ,handle hinges in respect to Easening of door / windows/cupboards (SteelWooden/Aluminium) of any description and size by cleaning, adjusting in position and making the same functional incl small repairs if reqd with and incl greasing, oiling, screws/nales for fixing the fittings.

Comprehensive maintenance to masonary work by attending day to day complaints of masonary related works such as plastering of wall/ceiling/chajja/making of jambs,soffit,cills etc of size not exceeding 0.25 sqm or on patch work including finishing with distemper/white wash/cement based paint/exterior emulsion paint including two coats of putty as required at site to match with existing surface.

Comprehensive maintenance to plumbing work by attending day to day complaints of plumbing nature like leaking bib taps, stop cock of any pattern or of any type including minor repairs to flush cistern, GI pipe leakages, removing air blockages if any and refixing old serviceable bib cocks, stop cocks any pattern after minor repairs such as replacement of washers,jumpers and spindle etc complete all as specified and directed. Minor items like thread , Tefon tape, rubber washer shall be deemed to be included in the quoted rates. (any major parts such as jumpers, brass spindles ,caps etc to be measured as supply only and paid for accordingly)

Note for item No 01 to 03. The scope of work is of day to day maintenance nature/ requirement of works. Contractor shall attend the office of AGE B/R-I on daily basis and receive/ collect the complaints/ requirememts of works and shall rectify the repair/maintenance works within time given below :- (a) Minor plumbing complaints - 48 hours (b) Minor Joinery complaints - 48 hours (c) Minor masonary complaints - 48 hours (d) Major Plumbing - 5 days (e) Major Joinery - 15 Days. If contractor fails to rectify the complaints with materials/ items to be replaced if required a penalty @ 50% of quoted rate by the contractors of that particular item shall be recovered from his payment. The responsibility of getting the complaints attended & rectified shall lies with the contractor even if he fails to complete the complaints within 48 hours. In the delayed case of a rectification of complaints even after 48 hours, he shall rectify the same within one week. (Note :- The complaint received from complaint cell shall have to be attended on same day).

Demolition of cement concrete (unreinforced) including tiles of any description & terrazo finish, etc. in ground floors and pavings n. exc 15 cm thickness (below or above ground level) all as specified

M & L 75mm thick, cement concrete 1:3:6, type C2 (40mm graded aggregate) as in floors, plinth protection, paths, etc and finishing top surfaces even and smooth (without using extra cement) all as specified

Demolition of brick work or stone / boulder masonary, built in cement mortar including all quoins, arches, pillars etc., complete all as specified

M&L brick work with sub class `B' bricks straight or curved on plan exc 6.0m mean radius built in cement mortar 1:6 complete all as specified.

Taking down cement or cement lime plaster of any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specied

M & L 15 mm thick rendering in CM (1:6) on brick surfaces or conc surfaces on walls and finished even and smooth without using extra cement all as specified

M & L for rendering 5 mm thick on concrete surfaces such as ceiling or soffits of chhajas etc; in CM 1:3 finished even and smooth without using extra cement all as specified

M &L for applying two coats of white wash on newly plastered ceiling surfaces including preparation of these surfaces all as specified

M&L for applying two coats of oil bound destemper ( to match with the adjacent shade or tint) over a coat of primer on newly plastered wall surfaces including applying wall putty to make up depression etc and to the surface even & smooth including preparation of these surfaces all as specified

Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified.

M & L Non-skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15mm thick screed bedding layer in CM 1:6 and including roughening surfaces of old concrete/terrazzo finish floor by picking, sweeping clean and washing down with water to remove dust etc/ dismantling old tiles of any description, complete all as specified

M & L Non-skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, on vertical surfaces as in skirting etc. set and jointed in neat cement slurry/paste and pointed in white or coloured cement to match over and including 10mm thick plaster in CM 1:4 including taking down old plastered/terrazzo finishes/old tiles etc; complete, all as specified

M&L non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry & pointed in white or coloured cement to match over and including 15mm thick screed in CM 1:6 and including dismantling of old tiles/terrazzo finish etc, complete all as specified

M & L glazed ceramic coloured tiles of approved quality in vertical surfaces 350mm X 250 mm x7mm/450 x 300 x 7mm thick set jointed in neat cement slurry/paste and pointed in coloured cement to match with the tiles over and including 10mm thick plaster in CM 1:4 and including dismantling of old tiles/terrazzo finish etc; complete all as specified

S&F in repairs stainless steel wire cloth 0.36mm nominal dia of wire and 1.40 mm average width of aperture fixed with tinned tacks or galvanised wire staple, complete all as specified

S & F in repairs 300mm mild steel ordinary rat tail rod springs, including roller & roller plate complete all as specified

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/springs clips

S & F for 4 mm thick, sheet glass ordinary quality and glazing with rubber biding for aluminium window in square n. exc 0.5 sqm in each pane all as specified

S & F 3.0mm thick figured glass, pin head type and glazing with oil putty in squares n. exc 0.50 Sqm in each pane all as specified

S&F in repairs tank nipple suitable for HDPE water tank (minimum weight 20 mm - 45 gms) complete all as specified and directed .

M&L for 25mm dia fancy type PVC coated on MS pipe coloured curtain rod with brackets and knobs at both ends as per site requirement including taking down old existing PVC conduit pipes with accessories complete all aspecified

S & F in repairs soap dish stainless steel , complete all as specified

S&F in repairs PVC waste pipe with socket suitable for connection to Waste fittings of 32/40mm dia, and of length minimum 75 cm all as specified

Taking down or up 15 mm bore galvanised iron tubing and connection including cleaning for refixing or removal all as specified

Taking down or up 20 mm bore galvanised iron tubing and connection including cleaning for refixing or removal all as specified

S & F GI tubing medium grade with all fittings and fixed to walls & ceilings or laid in floors, bore of pipe 15 mm complete all as specified

S & F GI tubing medium grade with all fittings and fixed to walls & ceilings or laid in floors, bore of pipe 20 mm complete all as specified

S & F in repairs 15mm bore brass bib taps , screwed down, screwed for iron pipe or for brass ferrule complete all as specified

S & F in repairs PVC lid (cover) for 500 to 1000 ltr capacity PVC water tanks with hinging & lockng arrangement complete all as specified

S & F in repair ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of size 20mm bore ( weight 210 gms Minimum) complete all as specified

S & F in repairs, brass chromium plated shower rose 125mm dia, with swivel joints & and arms, and fixing to pipe & union all as specified

S & F in repairs 15mm bore, fancy type , chromium plated, angle valve, cast copper alloy, screwed down high pressure with crutch or butterfly handle,screwed both ends for iron pipe all as specified (Make :- Kingstone, Seico, Prayag)

S & F in repair PVC connection 15 mm size with PTMT nuts of length 600 mm of approved quality

S & F in repair PVC valveless, syphonic action type flushing cistern, low level, with inlet ball valve, float and handle including brackets, PVC bend long type and connectin to flush pipe of any size and pattern complete all as specified

S & F in repair vitreous china wash basin, white, flat back, size 550 x 400mm excluding taps, wastes but including brackets complete all as specified

S & F in repairs sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x460mm bowl size 410mm x330mm x160mm complete all as specified

S&F in repairs stainless steel plate racks of size 900mmx600mmx250mm and thickness of SS strip 1mm, fixed on wall etc complete all as specified & directed by Engr-in-Charge.

S & F in repairs brass chromium plated tubular towel rail, 20mm dia, D type 60cm long between flanges all as specified

S & F in repairs 15mm bore fancy type chromium plated bib taps, quarter turn cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified.(Make :- Kingstone, Sieco, Prayag)

S & F in repairs 15mm bore fancy type chromium plated stop valve cast copper alloy, with long shank & cup (concealed type) with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified.

S & F in repairs brass chromium plated bottle traps for wash basins with inlet and out let screwed for pipe or connections including necessary packing, union and cap all as specified

S & F in repairs 32/40mm waste fittings, brass chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and flynuts, flange end bedded in red lead cement complete all as specified

S & F in repairs 32/40mm waste fittings for stainless steel sink(sink coupling) , brass chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and flynuts, flange end bedded in red lead cement complete all as specified

S & F in repairs CP grating (with or without waste hole), 125 mm size, fixed on floor/nahani traps etc complete all as specified

S & F in repairs 110 mm bore of pipe PVC (SWR) pipes single socket in any length with rubber ring joint fixed to walls with MS clamps etc all as specified

S & F 110 mm bore, PVC (SWR) fittings such as bends of any radious, tee, shoe etc; fixed to PVC pipes, complete all as specified

Dismantling / taking down 15 mm dia bib cock/ stop cock/angle cock of any pattern or any type and re-fixing the same after minor repairs such as replacement of washers etc or complete all as specified and directed (any major parts such as jumpers brass/ spindles/ caps etc required to be replaced, shall be measured as supply only and paid for accordingly)

Supply and fixing in repairs bib cock PTMT standard 15 mm dia of any colour, high pressure screwed for iron pipe & fixed ( male or female as required) complete all as specified and directed

Supply only Jumper brass with rubber or leather washer complete for 15 mm dia bib cock / stop cock brass complete all as specified and directed

Supply only spindle brass for 15 mm dia CP Bib cock/ pillar cock/ concealed cock of any pattern complete all as specified and directed.

Supply only capstan head / cap of CP bib tap / CP stop cock 15 mm size complete all as specified and directed.

S & F in repairs 20mm bore, gun metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified

S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white, including connection to drain (or outgoing pipe) and to flushing pipe, ant-syphonage pipe, etc. complete all as specified

Fixing only in repair vitreous china wash basin, of any description & size, excluding taps, wastes but including brackets complete all as specified

S&F in repair flush pipe of polyethene of low or high density or PVC, 32mm dia, for low level cistern and fixed complete all as specified and directed.

Dismantling and disconnecting of existing CI soil vent pipe 100 mm bore fixed to wall,laid in trenches incl all fittings & accessories, all as directed.

Dismantling and disconnecting of existing CI soil vent pipe 75 mm bore fixed to wall,laid in trenches incl all fittings & accessories, all as directed.

S & F cast iron soil waste and vent pipe 75mm bore with or without ears fixed with chemical cement joints laid in trenches/floors or fixed in walls, all as specified.

S & F cast iron soil waste and vent pipe 100mm bore with or without ears fixed with chemical cement joints laid in trenches/floors or fixed in walls, all as specified.

Sealing only joints of cast iron pipes and fittings 75/100mm dia with chemical cement and making the joints leak proof complete all as specfied

S&F in repairs oval access doors to cast iron pipes of 75mm bore with rubber washer packing & bolts & nuts as required complete all as specified

S&F in repairs oval access doors to cast iron pipes of 100mm bore with rubber washer & bolts & nuts as required complete all as specified

S & F in repairs CI bends any radius, 100mm bore, diminishing pieces or tapers, etc with or without oval access doors, complete all as specified

S & F in repairs CI bends any radius, 75mm bore, diminishing pieces or tapers, etc with or without oval access doors, complete all as specified

S & F in repairs 100mm bore CI branch pieces, double (spigot or socketed type) with oval access doors

S & F in repairs mild steel Butt Hinges, 100 mm size, medium weight, cold rolled fixed with screws/welding to wooded/steel frames or chowkats, complete all as specified

M&L welding in repairs with thickness of metal not exceeding 6mm and not exceeding 2.5 cm in length etc complete all as specified and directed by Engineer - in – Charge.

S & F in repairs 200 mm aluminium anodised, barrel tower bolts of extruded section all as specified

Supply and fixing in repair 125 mm long aluminium handles, fabricated type, anodised and fixed complete all as specified and directed.

S & F in repairs for PTMT ( Poly Tetra Methylene Terephthalate ) butt hinges 100mm long best quality all as specified

S & F in repairs PTMT ( Poly Tetra Methylene Terephthalate ) barrel tower bolt best quality, 150 mm long all as specified

S & F in repairs PTMT ( Poly Tetra Methylene Terephthalate ) door handles, best quality, 125 mm long all as specified

S&F in repair PVC Knob/Handle (as per sample) for 10 ltr capacity PVC low level flushing cistern complete all as specified and directed.

S&F in repair PVC Syphon Kit (as per sample) for 10 ltr capacity PVC low level flushing cistern complete all as specified and directed.

S&F in repair complete Veta washer set (as per sample) for 10 ltr capacity PVC low level flushing cistern complete all as directed.

Fixing only in repair low level flushing cistern any capacity after carrying out minor repairs such as stopping of leakage etc. complete all as specified and directed.

Cutting chases in brick walls girth exc 10 cm but not exc 20 cm wide for concealed water tubing etc and making good in CM 1:3 or PCC 1:2:4 as required complete all as specified and directed.

Dismantling carefully cement concrete in floor, etc around floor traps or any other concealed fittings, ( replacing floor traps/fittings if required and shall be paid at supplied only rate separately), sealing joints with solvent cement or other suitable materials and making joint leak proof and making good surfaces with PCC 1:2:4 or CM 1:3 (repair/replacement of tiles in floor shall be measured and paid separately), complete all as specified

Supply only floor trap 75/100 mm dia with grating including jointing to waste pipe

Demolition of cement concrete of any description and in any position not otherwise speciallly provided for complete all as specified and directed

M&L PCC 1:5:10 type D-2 using 40mm graded crushed/stone agg for foundations, filling & mass concrete, sub-base & sub-floors, etc. complete all as specified.

M&L appply for a layer of hot blown bitumen of 85/25 penetration grade @ 1.7 kg/sqm incl cleaning the surface of roof or sunken etc complete all as specified

M&L 15mm thick cement plaster in CM 1:4 with water proofing compound (WPC to measurment & paid separately) and finishing top surface even & smoth as in roof slab /sunken floor , etc all as specified

Taking down chowkhats or frame n exc 1.50 Sqm each with shutters (W/out taking off shutters from the frames).

Taking down chowkhats or frame exc 1.50 Sqm but n exc 4 Sqm each with shutters (W/out taking off shutters from the frames).

Taking down shutters of any description exc 1 Sqm & nexc 2 Sqm each.

S&F for pressed steel frames of size 125 X 60 mm with one or more rebates including necessary fixing lugs hinges, locks strike plate etc(thickness of sheet shall be 1.25mm) and making good the plaster of wall in CM 1:6.

S&F for pressed steel frames of size 105 X 60 mm with one or more rebates including necessary fixing lugs hinges, locks strike plate etc(thickness of sheet shall be 1.25mm) and making good the plaster of wall in CM 1:6.

S&F 2nd class HW 35mm thick factory made panelled shutters with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and style as per IS-1003 (Pt-I)kiln seasoned and chemically pressure treated.

M & L 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides all as sppecified

S & F in repairs 15mm bore, brass CP central hole basin mixer for mixing hot & cold water screwed down for iron pipe all as specified

S & F in repairs 15mm bore, brass CP central hole wall mixer for mixing hot & cold water screwed down for iron pipe all as specified

M&L for preparation of new or previously untreated wood and wood based surfaces of any description exc 10 CM width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube fixed in opening as per specifications and making good the plaster of wall in CM 1:6..

S&F factory made solid panel shutter (PVC) 30mm thick (Style) consisting of frame made out of MS tube for top and bottom rails MS frame shall be covered with heat molded plain colour PVC `C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement as per specifications.

S&F in repairs 18/19 mm thick pre-laminated particle board, interior grade, fixed with screws to timber frame work as in kitchen cupboards, drawers, shutters, shelves etc including teak wood lipping, 6mm thick on edges fixed with nails etc, complete all as specified

S&F 100mm Butt hinges, extruded aluminium alloy with galvanished mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 (using 20mm gde stone agg) as in filling of Chowkhats.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and 1.40 mm average width of aperture fixed with tinned tacks or galvanised wire staple, complete all as specified

S&F of MS 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete as specified

S&F butt hinges 100mm medium weight cold rolled mild steel and fixed complete all as specified.

S&F for MS tower bolt 200 mm long stove enamelled black with bright bolt.

S&F for MS sliding door bolt 250 mm long stove enamelled black with bright bolt etc.

S&F for MS pressed handles, oval type stove enamelled black 125 mm long.

S&F for Aluminium anodised barrel tower bolt 150 mm long of extruded section complete all as specified..

S&F for Aluminium handles, cast type anodised 125 mm long for cup boards and doors.

S&F for Al hasp and staple 100 mm size.

M & L MS work as in framed brackets of angles as sink brackets and cooler stand.

Dismantling boarding any description fixed in any position with rails incl fillets

S&F fillets, rectangular sectional area exc 3 sq cm but n.exc 6 sqcm IInd class hardwood for cupboard shutter.

S&F continuous (piano) hinges, mild steel, bright finish or electrogalvanised with width of flap when open is 30 mm.

Taking down shutters of any description exceeding 1.00 sqm but not exceeding 2.00 sqm each and refixing in the same opening including easing and adjusting including renewal of unserviceable screws etc. complete all as specified

Taking down shutters of any description not exceeding 1.00 sqm each and refixing in the same opening including easing and adjusting including renewal of unserviceable screws etc. complete all as specified

Re-securing or easing & adjusting, without taking down shutter of any description t exc 1.00 sqm but n exc 2.00 sqm each complete all as specified and directed.

Re-securing or easing & adjusting, without taking down shutter of any description not exc 1.00 sqm each complete all as specified and directed.

Cleaning of water tanks exc 250 & n. exc 500 ltr capacity including removing all scale & dirt, etc., from tanks and from mouths of circulating pipes etc. all as specified

S&F in repairs three layers rotational moulded polyethylene water storage tanks (cylindrical vertical top) hoisted and fixed in position 500 litre capacity white in colour complete all as specified and directed.

S & F in repair Corner glass shelf (25cm/30cm ) with CP brass bracket & railing etc; complete all as specified

M & L for applyingone coats Distempering on old surfaces with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification, including preparation of these surfaces duly filled the nail holes and depressions with wall putty of same tint to match with colour of distemper, smoothering the surface and finally cleaned floors, complete all as specified and directed.

M & L for applying two coats Distempering on old surfaces with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification, including preparation of these surfaces duly filled the nail holes and depressions with wall putty of same tint to match with colour of distemper, smoothering the surface and finally cleaned floors, complete all as specified and directed.

M & L for applying one coat of white wash on old decorated plastered or unplasted surfaces on ceiling, including preparation of these surfaces duly filled the nail holes and depressions with wall putty of same tint to match with white wash, smoothering the surface and finally cleaned floors complete all as specified

Preparation of old painted wooden and wood based surafaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint of approved tint, quality, colour on these surfaces, including cleaning of floor/wall surfaces complete all as specified

Preparation of old painted steel & iron surfaces of any description not otherwise described over 10 cm width or girth and applying one coats of synthetic enamel paint of approved tint, quality, colour on these surfaces, including cleaning of floor/wall/glass pane surfaces complete all as specified

M & L in repairs for 4mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Alumi nium framework with screw, complete all as specified and directed.

S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S&F in repairs Jet spray CP, brass body with wall hook and 1 mtr SS pipe complete all as specified.

S&F in repairs plastic water closet seat cover white/ivory colour closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified.

Taking down carefully existing copper/Aluminum point wiring (light,fan, socket or power) complete including fixture and fittings such as switches, bellpushes, ceiling roses, pendents, regulators, sockets, light fitting, callbells etc removiing materials to store for keeping in safe custody or for taking credit(credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors etc. to match existing complete allas specified and directed

M & L for Point wiring with multi-stranded copper conductor, single core, PVC insulated and unsheathed cable, including PVC insulated unsheathed multistranded copper conductor single core cable as earth continuity conductor to common earth and connected to earth dolly, GI terminal boxes, modular frame & cover plate (suitable for modular switch/sockets) comprising the following: -

One light point controlled by one switch or one fan point controlled by one switch & fan regulator etc. with 2.5 Sq. mm (nominal area) cable & 2.5 Sq. mm (nominal area) cable as earth continuity conductor, in existing concealed conduit all as specified.

One Socket outlet three pin, 6 Amp, on the same board, with 2.5 Sq. mm (nominal area) cable & 2.5 Sq. mm (nominal area) cable as earth continuity conductor, all as specified.

One Socket outlet three pin, 6 Amp, independent, with 2.5 Sq. mm (nominal area) cable & 2.5 Sq. mm (nominal area) cable as earth continuity conductor, in existing concealed conduit all as specified.

One Bell/Buzzer point controlled by one push button with 1.5 Sq. mm (nominal area) cable & 1.5 Sq. mm (nominal area) cable as earth continuity conductor, in existing concealed conduit all as specified.

One light point controlled by two two way switch. with 1.5 Sq. mm (nominal area) cable & 1.5 Sq. mm (nominal area) cable as earth continuity conductor, in existing concealed conduit all as specified.

One socket outlet three pin, 5/15 Amp, independent, with 2.5 Sq. mm (nominal area) cable & 2.5 Sq. mm (nominal area) cable as earth continuity conductor, in existing concealed conduit all as specified.

S&F Ceiling rose, 3 terminal PVC/polycarbonate, suitable for 230 V, AC, 50 Hz supply.

S&F call bell ding dong type AC 230 V complete.

S&F wall mounted extruded Aluminium/polycarbonate integrated LED batten fixture with tube 1.2 m, 20watt, 1.2 m 6500K,efficacy not less than 90 lumen/watt, extruded Aluminium/polycarbonate, PC diffusor and integrated inbuilt driver complete complete including making connection complete all as specified and directed.

S&F wall mounted extruded Aluminium/polycarbonate integrated LED batten fixture with tube 1.2 m, 25watt, 1.2 m 6500K,efficacy not less than 90 lumen/watt, extruded Aluminium/polycarbonate, PC diffusor and integrated inbuilt driver complete complete including making connection complete all as specified and directed.

S&F decorative wall light fixture made of polycarbonate suitable for retrofit 9W LED lamp(base B-22) complete with PC diffusor & including one 9W LED lamp(base B-22), 6500K, not less than 90 lumen/watt efficacy including making connection complete all as specified and directed.

S&F round shape 6 watt 220V AC surface type with high efficiency PMMA diffusor soft glare free light complete with drivers, holders, LED lamps suitable for roof ceiling including making connection complete all specified and directed

S&F Lamp holder PVC/polycarbonate type with back plate complete all as specified

S&F LED 7W lamp(base B-22) 6500K, not less than 90 lumen/watt efficacy complete all as specified and directed.

S&F in replacement sub main two single core PVC copper conductor unsheathed wire multi stranded 6 sqmm along with earth wire 6.0 sqmm copper conductor single core wire connected by common earth in existing surface/recessed PVC/steel conduit and including all as specified.(Note:- Three lengths of 6 Sqmm cable will be measured as one length). (Note :- two lengths of 6.0 sqmm cable and one length of 6.0 sqmm earth cable will be measured as one running length)

S&F in replacement sheet metal encloser double door 12 way SPN 240V ISI marked complete with neutral and earth link and bus bar complete made out of CRCA steel sheet Factory made including blanking plate for unused module complete all as specified and directed

S&F in replacement single pole and neutral enclosure 240V with a two pin and earth plug and socket complete with one double pole MCB 20Amp complete all as specified and direcetd

S&F in repair MCB 40 -63 Amp 240V SP 10 KA ‘B’ series complete all as specified

S&F in repair MCB 6-32 Amp 240V SP 10 KA ‘B’ series complete all as specified

S&F in repair MCCB 415V, FP 63A 16kA complete all as specified

M & L for earthing with galvanized steel plate electrode 600 x 600 mm x 6 mm size directly burried in ground vertically to earth pit not less than 2.25 meter deep below normal ground level with top edge of the earth plate not less than 1.5 m below normal ground level surrounded with coal dust and common salt filling in alternative layers of 15 cm thick each connected to and including GI earth wire 4 mm dia by means of nuts, bolts, check nuts & washers etc connecting to earthing test point, main switch board and including 15 mm dia GI pipe light grade for protection of earth lead from earth plate to distribution board and 20 mm dia GI pipe medium grade connected with funnel having wire mess for watering purpose including necessary excavation and earth work, PCC (1:2:4) type B-1 (using stone aggregates) for earthing pit, 10mm thick cast iron cover with angle iron frame all as specified and shown in electrical plate No 3 of SSR Part-I and testing on completion including replacement of old unserviceable. Note:- It is mandatory to paint a sqaure shape notice board of yellow color with legible black color letters of earthing mentioned details as below; Cost incurred deemed to be inlcuded in quoted rate:- (i) CA No. (ii) Date of installation after initial testing & Value of earth resistance in Ohm (iii) Date of last testing (iv) Value of earth resistance in Ohm in last test

S&F in repair Switch piano, flush type single pole, one way 5 Amp complete all as specified

S&F in repair Switch piano, flush type single pole, two way 5 Amp complete all as specified

S&F in repair Switch piano, flush type single pole, one way 15 Amp complete all as specified

S&F in repair Bell push 5/6 Amps 230 V AC complete all as specified

S&F in repair Socket outlet 3 pin, 5A, flush type all as specified

S&F in repair Switch socket combination 2 in 1, 3 pin, 5 and 15 Amp flush type universal complete all as specified

S&F in repair Socket outlet 2 in 1, 3 pin, 5 and 15 Amp flush type complete all as specified

S&F in repair Stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as reqd complete all as specified

S&F in repair rigid non-metallic PVC conduit external dia 20mm in size inclusive of all tees, bends, elbows, reducers, junction boxes, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. Complete all as specified

S&F in repair Hylam sheet cover 3mm thick of size 5"x5" complete with machine screw/ washer with provision of slots for switches, sockets, fan regulators (including refixing of all switches, sockets, fan regulators dismentaled from existing sheets) complete all as specified

S&F in repair Hylam sheet cover 3mm thick of size 8"x5" complete with machine screw/ washer with provision of slots for switches, sockets, fan regulators (including refixing of all switches, sockets, fan regulators dismentaled from existing sheets) complete all as specified

S&F in repair Hylam sheet cover 3mm thick of size 13"x8" complete with machine screw/ washer with provision of slots for switches, sockets, fan regulators (including refixing of all switches, sockets, fan regulators dismentaled from existing sheets) complete all as specified

S&F LED light fitting 9/10W bulkhead luminaires incluing LED light, driver, holder connecting up with three core flexible copper conductor cable of suitable size complete allas specified and directed

NOTE :- ARMAAN COMPLAINT/DAY TO DAY COMPLAINTSN/DOOR TO DOOR COMPLAINTS:- Complaints regarding repair/replacement to these items to be attended unconditionally. All in cost incurred upon deemed to be included in respective items

Note:- Net contract sum shall be calculated after deduction of Sch of credit.

M/s Kataria Construction Company

BALAJI CONSTRUCTIONS

R K GOYAL AND CO

SACKSON ENTERPRISES

Singla Enterprises

Easyways Enterprises

SHARDA ENTERPRIES