Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹21.7 LAccepted-AOC | L1 | Accepted-AOC Being lowest and reasonable | |
| 2 | L2₹25.4 L+₹3.4 L (15.2%)Rejected-Finance ROWRIAH KB ROAD PO CHALIHA JORHAT 785004 ASSAM | JORHAT | JORHAT | ASSAM | 785004 | L2 | Rejected-Finance Being not lowest | |
| 3 | L3₹26.1 L+₹4.1 L (18.4%)Rejected-Finance | L3 | Rejected-Finance Being not lowest |
Tender Value
₹19 L
EMD Value
₹38,000
Closing Date
21 Nov 2022, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GARRISON ENGINEER
Garrison Engineer Jorhat 785005 Assam
SPL REPAIR OF BLDG NO T-146 AT LICHUBARI AREA
2022_MES_509471_4
8046/E8
Open Tender
Civil Works
Item Rate
180 days
JORHAT-785005
Please refer tender documents
3 documents required · 3 mandatory
₹500
GE JORHAT
₹38,000
Yes
29 Nov 2022
31 Oct 2022
23 Nov 2022
31 Oct 2022
21 Nov 2022
8 Nov 2022
31 Oct 2022 - 5 Nov 2022
Amount
NOTES :(i)The bidders/contractors are advised to read tender document & all corrigendum/ amendments and General conditions of contracts before entry/quoting the rates.
Demolition of cement concrete (reinforced) in ground floors and paving not exceeding 15 cm thickness (below or above ground level)
Precast Reinforced Cement Concete cover slab type M-20(Nominal Mix) using 20 mm graded stone aggregate, set in Cement Mortar (1:4).
Material and labour for Reinforced Cement Concrete M-20 (Nominal mix) using 20 mm graded stone aggregate as in slabs supported on walls, beams and Columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.
Use and waste of formwork to soffits of suspended slabs such as roof slab, floor slabs, landings not exceeding 200 mm thick (horizontal or sloping) for rough finished surfaces of concrete complete all as specified and as directed.
Material and labour for TMT Bars Fe 500D 6mm & 8mm dia cut to length bent to shape required inculding cranking bending spirally hooping for columns etc and binding with MS wire ennealed less than 0.9mm dia or securing with clip complete all as specified and directed.
Demolition of cement concrete (un-reinforced) in ground floors, sunken floor and paving complete all as specified
Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to stores and rubbish off the MOD premises complete all as specified and as directed.
Material and labour for 75 mm thick plain cement concrete M-10(Nominal Mix) using 20 mm graded stone aggregate as in plinth protection, finished even and smooth without using extra cement complete all as specified and as directed.
Plain Cement Concrete M-15(Nominal Mix) using 12.5 mm graded stone aggregate as in making good window opening, lintels upto 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, coping, kneelers, apex stones, bed plates, kerbs, water trough and the like including weathering slightly rounded or chamfered angles and throating as directed
Material and labour for100 mm thick plain cement concrete 7.5 (Nominal Mix) using 40 mm graded stone aggregate as in sub base floor complete all as specified and as directed.
Material and labour for pre-polished chequered Cement Concrete tiles of 25 mm minimum thick, size of (square/ rectangular) area of each tile exceeding 0.09 Sqm but not exceeding 0.16 Sqm double layer machine pressed set ( as per IS 1237-2012), jointed and pointed in neat cement slurry in floors and cut & polished in white or coloured cement to match over and including 15mm thick screed bed in CM (1:6) complete all as specified and as directed.
Material & Labour Non skid ceramic tiles, coloured, 7 to 8 mm thick (square/rectangular area of each tile exceeding 0.18 Sqm and not exceeding 0.36Sqm , in floors etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed layer in CM (1:4) including roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and brushign neat cement slurry with 3.0 kg of cement per Sqm complete all as specified and as directed.
Material & Labour Non skid ceramic tiles, coloured, 7 to 8 mm thick (square/rectangular area of each tile exceeding 0.11 Sqm and not exceeding 0.18Sqm , in floors etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed layer in CM (1:4) including roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and brushign neat cement slurry with 3.0 kg of cement per Sqm complete all as specified and as directed.
All as per item No 14 here-in-before but to vertical surfaces such as skirting over and including 10mm thick rendering in CM (1:3) complete
Material & Labour Glazed ceramic tiles 450x300x7 mm(Coloured) on vertical surfaces such as skirting, dados and riser to steps etc. set and jointed in neat cement slurry and pointed in coloured cement to match complete over 10mm thick screed bed vertical layer in CM (1:4)all as specified and as directed.
Material & Labour of 18mm thick granite ( of any type) work ( table rubbed and polished in pillars and like set in cement mortar (1:4) including pointing in white cement (1:2) using marble dust admixture of pigment to match with shade of granite over 15mm thick screed bed layer in CM (1:4) including taking down existing one complete all as specified and as directed.
Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.
Material and labour for old Brick work with bricks class designation 75, old size, straight or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:6 complete all as specified and as directed.
Taking down cement plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. and removal outside of MOD land complete all as specified and as directed.
Rendering 15 mm in Cement Mortar 1:6 on fair faces of brick work or concrete surfaces finished even smooth without using extra cement to the plastered surface complete all as specified and as directed.
Material and labour for Rendering 15mm thick plaster in Cement Mortar (1:4) on fair faces of brick or concrete surface of wall and finished even and smooth without using extra cement, with water proofing treatment. Note:- Water proofing compound shall be measure and paid separately
Rendering 5 mm in Cement Mortar 1:3 on fair faces of brick work or concrete ceiling surfaces finished fair
Supply only integral liquid water proofing compound
Material and labour for Preparation of new surface and applying two coats of 1st quality acrylic washable distemper (ready mixed) having VOC content less than 50 gms/litre of required colour shade and as per manufacturer’s specification over a coat of primer over a coat of 1.5 mm thick cement base wall putty complete all as specified and directed.
Material and labour for complete removal of existing finishing of internal wall surface of building/structure by mechanical appliance and preparation of old surfaces and applying two coats of 1st quality acrylic washable distemper (ready mixed) having VOC content less than 50 gms/litre of required colour shade and as per manufacturer’s specification over a coat of primer over a coat of primer over a coat of 1.5 mm thick cement base wall putty complete all as specified and directed.
Material and labour for Preparation of new surface and applying 3 coats white wash on walls surface complete all as specified and as directed.
Material and labour for Preparation of new surface and applying 3 coats white wash on ceiling surface complete all as specified and as directed.
Material and labour for preparation of old internal ceiling surfaces and applying a coats of white wash complete all as specified and directed.
Material and labour for preparation of old internal wall surfaces and applying a coats of white wash complete all as specified and directed.
Material and labour for complete removal of existing finishing of internal wall surface of building/structure by mechanical appliance and applying 2 coats of cement based paint over a coat of alkali based primer of any description over 10 cm girth or width complete all as specified and directed.
Material and labour for preparation of new surfaces and and applying 2 coats of cement based paint over a coat of alkali based primer complete all as specified and directed.
Material and labour for preparation of old wood surfaces and and applying one coats of synthetic enamel paint on wooden surfaces of any description over 10 cm in girth or width complete all as specified and directed.
Taking down chowkats/frames with shutters (without taking off shutters from the frame) etc. exceeding 1.50 Sqm but not exceeding 4.00 Sqm each complete all as specified and as directed.
Taking down chowkats/frames with shutters (without taking off shutters from the frame) etc. not exceeding 1.50 Sqm each complete all as specified and as directed.
Material and labour for Solid PVC door frame of size 50mm x 47 mm made out of 5 mm wood grain printed PVC sheet reinforced with Mild Steel square tube, suppling & fixing in opening as per drawing complete all as specified and directed.
Material and labour for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and directed.
Material and labour for factory made single extruded WPC (Wood Polymer Composite) solid door Frames/ Chowkhat of size 50x125mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp¬ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: 1. For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. 2. M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately
All as per item no 38 here-in-above but 45x 85 mm .
Factory made solid PVC Moulded Door Shutter, 28 to 30 mm thick (stiles), 2,4, or 6 raised panel design with 2 mm thick Moulded prelam PVC sheet on the front face and 2 mm plain colour prelam PVC sheet on back face supplying & fixing in the frame at site as per specification & drawingcomplete all as specified and directed..
Supply and fixing Factory made solid panel wire guage PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelam PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling wii be wire guage. The wire guage shall be wrappedon an additional square 8 mm MS solid tube.This tube shall be welded to MS tube. The wire guage shall be stretched to tighten firmly, suppling & fixing in the frame at site as per specification & drawing
Material and labour for mild steel work as in bands, straps, supports or stays for RWP, ventilating pipes, clamps, hold fasts, wall ties conforming to Fe-290 Gde E-165
Material and labour for Butt hinges Stainless steel 100 mm size complete all as specified and directed.
Material and labour for Aluminium anodised barrel tower bolts of extruded section size 200 mm complete all as specified and directed.
Material and labour for Aluminium anodised barrel tower bolts of extruded section size 150 mm complete all as specified and directed.
Material and labour for Aluminium anodised sliding door bolt, with hasp & staple (bolt type) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sections 300 mm long .complete all as specified and as directed.
Material and labour for Floor door stopper of SS body and tongue, anodised, with hard drawn steel spring of size 150 mm, fixed in floor complete all as specified and directed.
Material and labour for Aluminium handles cast type anodised 125 mm size complete all as specified and directed.
Material and labour for Aluminium handles cast type anodised 150 mm size complete all as specified and directed.
S&F wooden with stainless steel fancy type curtain brackets complete all as specified and directed.
Supply and fixing of tubular curtain road, stainless steel ss-304, 20 mm dia 1.25 mm thick fixed to brackets complete all as specified and as directed.
Material and labour for 18/19 mm thick prelaminated particle board exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work. Complete all as specified and directed.
Supply and fixing of 300mm ordinary rat tail rod pattern springs including roller and roller plate complete made out of brass complete all as specified and as directed
Supply and fixing of steel ventilator with top hung shutters including hinges with steel handle and steel peg stay complete without gauged bars, dovetailed or welded complete all as specified and as directed
Supply and fixing of steel windows with side hung shutters including hinges projecting type with steel handle and steel peg stay complete with gauged bars, dovetailed or welded complete all as specified and as directed
Supply and fixing of steel windows with side hung shutters including hinges box type with steel handle and steel peg stay complete without gauged bars, dovetailed or welded complete all as specified and as directed
Materials and labour for Mild Steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290(Gde E-165) complete all as specified and as directedincluding taking dwon old one complete all as specified and as directed.
Material and labour for Stainless steel wire cloth, 0.36 mm nominal dia of wire and avergae width of aperture 1.00 mm and fixed with stainless steel wire staples complete all as specified and directed.
Supply and fixing of sheet glass 4 mm thick ordinary quality fixed to aluminum window in squares in each pane of required size complete all as specified and as directed.
Supply & Fixing of Glazing with sheet glass (frosted on one side) 4 mm thick ordinary quality with oil putty in square not exceeding 0.5 Sqm in each pane.
Material and labour for preparation of new steel surface and applying two coats of synthetic enamel paint over a coat of red oxide primer on new steel and iron surfaces of any description over exceeding 10 cm in width or girth complete all as specified and as directed..
Dismantling plain/corrugated steel sheeting, any guage, thickness including eves gutter / rain water pipe complete & removal all as specified
Dismantling steel work including gates, rafter, purlin, roof truss etc complete all as specified & as directed.
Material & labour of MS rolled sections as in in roof truss (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) and fixed with angle cleats, Fe-410-W(Gde-E 250) Quality Acomplete all as specified and as directed.
Supply and fixing of pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick and pitch length 75 mm c/c of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.
Supply and fixing of pre-painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in ridges, tips, valley, gutters, length & girth as fixed with nail or screws complete all as specified and as directed.
Material, labour and fixed of aluminium snap grid frame work for false ceiling, size of grid 605 x 605 mm, including aluminium main/closs tee of size 35mm x 23mm x 1.5 mm ( minimum) aluminum BULBED TEES section and aluminium angle of 25mm X 25mm X1.5mm thick, sutiable type GI wire hanging arrangement with adjuster all as specified in clause no 10.38 in SSR part-I and including 4mm thick high pressure steam cured non asbestos fibre cement designer board as per IS 14862 with applying of two coats of acrylic distemper over a coat of primer including taking dwon existing false ceiling system complete all as specified and directed.
Stripping out tarfelt from old roof surfaces and removing unserviceable materials from site of work in low laying in outside MOD area complete all as specified and as directed.
Material and labour forrendering 15 mm(Avg) thick in Cement Mortar 1:4 finished even and smooth witht using extra cement after preparation of old roof surface with brushing and applied neat cement slurry with 3.0 Kg of cement per Square Metre existing surface complete all as specified and as directed
Supplying and laying 3mm thick APP (Atactic Polypropylene Polymer) modified prefabricated five layer, weight not less than 3.6 kg/Sqm water proofing membrane, black finished reinforced with non woven polyester matt laying over a coat of bituminous primer @ 0.40 Ltr / Sqm and two coats of Bitumen based UV reflective paint with aluminium finish over APP membrane. The membrane shall be laid using butane torch and sealing all joints etc all as specified in Para 11.44.5 of SSR Part I complete all as specified and as directed.
Supply and fixing of 15mm bore galvanised steel tubes, medium grade with all fitting and fixed to walls, ceiling, floors and including taking up old GI pipe complete all as specified and as directed.
Supply and fixing of 20mm bore galvanised steel tubes, medium grade with all fitting and fixed to walls, ceiling, floors and including taking up old GI pipe complete all as specified and as directed. Note for item no 71 & 72:- All fitting & fixture such as Bends, Elbows, Tees, Short Pieces, Connectors, Back - Nuts Caps, Plugs, Unions, Flange (core) & flange (ring), reduction Tee, reducing socket, Male & female threaded socket, tank connector, holding clamp shall be provide as per site requiredment as as directed by AGE and same shall deem to be included in quoted rate.
Material and labour for Gun metal gate valve with iron wheel head, screwed both ends for iron pipe of 20mm bore complete all as specified and as directe
Supply and fixing in repair of bib cock cast copper alloy screwed down with long body with wall flange, and fixed for 15 mm bore GI tube pipe and all accessories complete all as specified and as directed. complete all as specified. Make :- Cat no PIS -08 of Prayag or equivalent model of make list as given in PS as approved by GE.
Supply and fixing in repair of chromium plated pillar cock cast copper alloy screwed down with long body with wall flange, and fixed for 15 mm bore GI tube pipe and all accessories complete all as specified and as directed. complete all as specified. Make :- Cat no PIS 02 of Prayag or equivalent model of make list as given in PS as approved by GE.
Supply and fixing in repairs Stop valves fancy type, chromium plated with long shank and cap (concealed type), cast copper alloy, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and of size 15 mm bore complete all as specified and directed. Make :- Cat no PIS -28 of Prayag or equivalent model of make list as given in PS as approved by GE.
Supply and fixing of Vitreous china squatting pan, 'Orissa' pattern, size 580x440 mm white with including CI ‘P’ or ‘S’ trap & integral foot rests fixed in cement concrete and including taking down existing one complete all as specified and as directed Make: CALINA S3010102 & S9030101 of CERA or equivalent model of make list as given in PS as approved by GE.
Supply and fixing of vitreous china wash basin white flat back, size 550 x 400 mm including CP waste coupling,with GI pipe brackets & , rag bolt in cement concrete/brick wall and including taking down existing HWB and making good wall surface complete all as specified and as directed. Make: Cat no S2040103 wash basin of CERA or equivalent model of make list as given in PS as approved by GE.
Supply and fixing as in repair of PVC low level flusing cistern 10 litres capacity white with ball valve & brackets with flush pipe complete all as specified and as directed. Make: CHIVAS of CERA or equivalent model of make list as given in PS as approved by GE.
Supply and fixing of Supply and fixing in repair of stainless steeel of 304 grade of kitchen sink with drain board of overall size 915mmx460mm and bowl size 410mm x330mmx160mm depth or equivalent made of 1mm thick stainless steel sheet with 32mm bore CP waste coupling including ball and chain 300mm long with bass cap rubber plug, 32mm bore PVC waste pipe (heavy duty) 90cm long, and bedded in cement mortar and fixed in CP cantilever brackets. complete all as specified and directed. Make: Cat No. 1239D of PRAYAGG or equivalent model of make list as given in PS.
Supply and fixing as in repair of PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and as directed.
Supply and fixing in repairof Towel Rail 600 mm long of chromium plated fixed with and including chromium plated brass screws and wooden/plastic cleats complete all as specified and as directed. Make :- Cat no BA-40 of Prayag or equivalent model of make list as given in PS as approved by GE.
Supply and fixing in repair of 125 mm dia of shower rose with 225 mm long arms, cast copper alloy chromium plated , swivel joints and fixed for 15 mm bore GI tube pipe and all accessories complete all as specified and as directed. complete all as specified. Make :- Cat no BS-76 of PRAYAG or equivalent model of make list as given in PS as approved by GE.
Supplying, hoisted and fixed in position of rotational moulded polyethylene water storage tanks in double layers and cylindrical vertical type with manhole lids(closed top) of 500 litres capacity with ISI marked and all as specified in IS 12701 and including taking down existing water tank complete all as specified and directed .
Supply and fixing of PVC ball valve for 20 mm dia GI pipe all complete complete all as specified and directed.
Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms)
PVC (SWR) floor trap, plain with grating including jointing with solvent cement, 75 mm dia of outlet.
Cutting into existing manhole for connecting new drain, making good to pipe & rendering, cutting out existing benching for and forming branch channel (half round or 3/4 section) in cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate for 150 mm bore pipe
Supply and fixing of uPVC of type-B for use in soil and waste discharge systems, single socket, 110 mm bore in any length including rubber ring joints and fixed to walls with clips and other standard material and including taking dwon old rain water pipe & removal from site all as specified in IS 13592 complete all as specified and directed.
All as per item no 75 above but 75mm bore complete all as specified and directed.
Supply and fixing of Unplasticized (uPVC )bend for 110 mm bore uPVC pipe complete all as specified and directed.
Supply and fixing of Unplasticized (uPVC )bend for 75 mm bore uPVC pipe complete all as specified and directed.
Supply and fixing of Unplasticized (uPVC )juction equal or unequal for 110 mm bore uPVC pipe complete all as specified and directed.
Supply and fixing of Chlorinated Polyethylene Chloride (CPVC) pipes 50 mm outside dia , having thermal stability for hot and cold water supply pipe line including taking down existing pipe line complete all as specified and as directed.
Supply and fixing of Cast Iron 'P' or 'S' Trap 100 mm bore with vent complete all as specified and as directed.
Subtotal of Sch A part-I
SCHEDULE 'A' PART - II FOR E/M PORTION (Sl No __ to ____)
Taking down carefully unserviceable copper / aluminium point wiring (light, fan, bell socket or power) including all fittings such as switches, socket, ceiling roses , regulators and switch boxes etc complete and making good the disturbed surfaces complete all as specified and as directed.
Material and labour for concealed point wiring complete with 1.5 Sqmm single core PVC insulated and unsheathed multi stranded copper conductor cable 1100 volt grade, FRLSH through and including 20 mm PVC conduit & its accessories, cadmium screws fixed in concealed surface of wall/ceiling/false ceiling and including 1.5 Sqmm single core PVC insulated and unsheathed multi stranded copper conductor cable FRLSH as earth continuity conductor and MS boxes made of 16 gauge MS sheet concealed type on walls cover 3mm thick laminated sheet for housing complete switch for One light/fan/bell point controlled by one way switch. Note :- Cutting chases and making good in walls shall be deemed to be included in the unit rate.
All as per item no 100 here-in-above but One 3 pin socket outlet 5 amps on the same board with other switches
All as per item no 100 here-in-above but above but for one 5 amp socket independent complete all as specified and as directed.
Material and labour for concealed point wiring complete with 2.5 Sqmm single core PVC insulated and unsheathed multi stranded copper conductor cable 1100 volt grade, FRLSH through and including 20 mm PVC conduit & its accessories, cadmium screws fixed in concealed surface of wall/ceiling/false ceiling and including 2.5 Sqmm single core PVC insulated and unsheathed multi stranded copper conductor cable FRLSH as earth continuity conductor and MS boxes made of 16 gauge MS sheet concealed type on walls cover 3mm thick laminated sheet for housing complete switch for One light/fan/bell point controlled by one way switch. Note :- Cutting chases and making good in walls shall be deemed to be included in the unit rate.
Supply and fixing of switch piano flush single pole one way 5 amps complete all as specified and as directed.
Supply and fixing socket outlet multipurpose 3 pin 5 Amps controlled by one switch.
Supply and fixing of switch piano flush single pole one way 15 amps complete all as specified and as directed.
Supply and fixing switch socket outlet multipurpose 3 pin 5 15 Amps controlled by one switch.
Supply and fixing in repair bell push flush type 5 Amps complete all as specified and as directed.
Supply and fixing in repair bell push flush type 5 Amps complete all as specified and as directed.
Supply and fixing in repair Bell multi music type AC, 230 volts single pole
Material and labour for Electronic type fan regulator step type 120 watt, 230 volt complete all as specified and as directed. Make : Code no 14502 of Anchor or equivalent model of make list as given in PS as approved by GE.
Supply and fixing ceiling rose surface bakelite 65x50mm three terminals complete all as specified and as directed.
Supply and fixing of LED surface/ceiling mounting(suspended from ceiling) box type light fitting 20Watt with LED Lamp , drive and made of epoxy powder coated extruded aluminium channel housing with high quality polycarbonate opal diffuser cover & high power LED’s as light source with 120 Lumen per watt (Minimum) and including all other standard accessories as per manufacture instructions ,internally pre-wired including connecting up three core1.00sq. mm copper conductor flexible wire/cable complete all as specified. Make : Model No CCS-100-20-65-HL2-DP-NWH of Crompton/ BCLAB 20W WH LED P of Bajaj or equivalent model of make list as given in PS as approved by GE.
Supply and fixing in repairs of LED surface/ceiling mounting(suspended from ceiling) box type light fitting 10Watt with LED Lamp , drive and made of epoxy powder coated extruded aluminium channel housing with high quality polycarbonate opal diffuser cover & high power LED’s as light source with 110 Lumen per watt (Minimum) and including all other standard accessories as per manufacture instructions ,internally pre-wired including connecting up three core1.00sq. Mm copper conductor flexible wire/cable complete all as specified. Make : Model No CCS-103-10-65-SL-DP-NWH of Crompton or equivalent model of make list as given in PS as approved by GE.
Supply & Fixing of LED street light fitting ( Building Security light) of 35Watt with LED lamp’s & driver and made of pressure die-cast aluminum housing, IP 65/IP 66 road way luminaries with UV stabilized polycarbonate cover or toughen glass cover & high power LED’s as light source with 110 Lumen per watt and electronic driver with efficiency > 85% . The light fitting shall be fixed on wall/pole with and including 25 mm dia( or higher size as per manufacturers recommendation) light grade GI pipe (bend to shape or as per manufacturers recommendation ) bracket 1.5 mtr long complete with MS flat iron clamp (clamps shall be 40 x 5 mm MS flat) nuts, bolts & washers including painting the clamps with two coat of aluminium paint over a coat of red oxide primer and including taking up old light fitting complete all as specified and as directed Make:- Model No- TRP-400-35-57-SL-LM-NSR of Crompton Greave/ NXT P 36L WH CR PC SD of Bajaj or equivalent model of make list as given in PS. Notes : GI pipe bracket and clamps shall be deem to be included above quoted rate..
Supply and fixing of sub main wiring with two single core 4.0sqmm (nominal area) PVC insulated copper conductor FRLSH, multi stranded, unsheathed 1100 volts grade IS-694 marked in PVC double lock casing caping and accessories accessories including one single core 4.0 sqmm copper conductor cable FRLSH as earth wire and including taking out old sub-main wiring complete all as specified and as directed. NOTE:- (a) All runs of copper conductor and one run of conduit shall be measured as one run length.
Supply and fixing of sub main wiring with two single core 6.0sqmm (nominal area) PVC insulated copper conductor FRLSH, multi stranded, unsheathed 1100 volts grade IS-694 marked in PVC double lock casing caping and accessories accessories including one single core 6.0 sqmm copper conductor cable FRLSH as earth wire and including taking out old sub-main wiring complete all as specified and as directed. NOTE:- (a) All runs of copper conductor and one run of conduit shall be measured as one run length.
Supply and fixing of sheet metal enclosure for MCBs to be used singal pole & nutral double door 8 Way 200 Amps rated busbar and including fixed with 25mm x 6 mm mild steel clamp of suitable length and including taking out old DB complete all as specified and as directed.
Supply and fixing of sheet metal enclosure for MCBs to be used triple pole & nutral double door 8 Way 200 Amps rated busbar and including fixed with 25mm x 6 mm mild steel clamp of suitable length and including taking out old DB complete all as specified and as directed.
Supply and fixing of MCB SP of rating 6 to 32 Amps 240 V complete all as specified and as directed.
Supply and fixing MCB DP 40 to 63 amps 415 volts 10KA breaking capacity.
Supply and fixing MCB four pole 40 to 63 amps 415 volts 10KA breaking capacity.
Materials and labour for cutting holes in cement mortar brick wall for fixing of 300 mm sweep exhaust fan and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required and superficial complete all as specified and as directed.
Taking down ceiling fans any size including cable connections and disconnecting of fan blades and removing the fan with blades to store yard and hanging ceiling fan in its original position or any other position including as per direction of Engineer-in-Charge including fitting and fixtures after carrying out the repairs i.e cleaning, greasing and filling, painting of fan with one coat of synthetic enamel paint by spraying machine after preparation of surface by cleaning all dust and filling cavity with filler, reassembling the fan etc including testing complete all as specified and directed by Engr-in-charge.
Supply, installation, testing and commissioning of factory made powder coated (CPRI approved) outdoor type, dust & vermin proof feeder pillar box made out of 3.15mm CRCA steel sheet of suitable size and angle iron 40 mm x 40mm x 6 mm , powder coated over one coat of red oxide primer suitably grouted in PCC-M10 using 20 mm graded stone aggregate including bus bar, internal wiring with PVC insulated single core cables of copper conductor of suitable size duly numbered with tags for the circuits with hinged double door shutters (front & rear), cubical type locking arrangement and slanted roof. The size of panel boards shall be suitable for housing the accessories given here under and also suitable for operation on AC 415 Volt, 3 phase, 50 Hz supply system including disconnecting of electric connection both incoming & out going from existing unsv indoor/outdoor feeder pillar boxes/busbar enclosers and unsv accessories and taking out panel from the foundation . The panel board shall comprise of following items & all specified in SSR Part-I clause no 19.21 and all as shown on drawing .
Note: Schedule of credit (SCHEDULE OF CREDIT) amount of Rs ₹ ___________ mentioned on Page No ____ shall be deducted from the total quoted amount of BOQ.
M/S DHAR AND DHAR
M/S GOPAL ROY AND CO
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .