GE 861 EWS-27/2023-24

Amount

Taking down cement plaster on brick or concrete surfaces including raking out joints, hacking for key scrubbing down with water etc complete all as specified and directed.

Demolition of brick work or stone boulder masonry built in cement mortar including all arches quoins etc but excluding ashlar facing, dressed stone work & precast concrete articles etc complete all as specificed and directed.

Demolition of cement concrete (unreinforced) in ground floors & paving n.exc 15 cement mortar thick (below or above ground level) complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.5 sqm but n exc 4 sqm complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n.exc 1.5 sqm complete all as specified and directed.

Taking down shutter of any description n/exe 1.00 sqm each complete.Removing to or from store.complete all as specified and directed.

Taking down shutter of any description exe 1.00 sqm but n/exe 2.00 sqm each complete all as specified and directed.

Dismantling timber scantling unframed 40 sqcm and over in section in any position, complete all as specified and directed by Engr-in-Charge.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets, complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories), complete all as specified and directed.

Dismantling plain or corrugated steel sheeting of any gauge & thickness including Nainital or similar pattern roof coverings, complete all as specified and directed.

Dismantling structural steel work including door gates but excluding framed work, complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connection, including cleaning for refixing or removal from site, complete all as specified and directed.

Taking up or down 20mm bore steel tubing and connection, including cleaning for refixing or removal from site, complete all as specified and directed.

Dismantling water tanks of any description exc 250 Ltrs n exc 500 Ltrs capacity and removing from site complete all as specified and directed.

Brick work with sub class 'B' bricks straight or curved on plan, exceeding 6m mean radius with old size bricks, built in cement mortar 1:4, complete all as specified and as directed.

15mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar 1:4 finished the surface even and smooth without using extra cement, complete all as specified and directed.

15mm thick rendering in cement mortar 1:4 on other than fair faces brick work or concrete surfaces, finished the surface even and smooth without using extra cement, complete all as specified and directed.

15mm thick rendering on fair faces of brick or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement, complete all as specified and directed.

Non-skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.06 sqm but not exc 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:6, complete all as spcified and directed.

Glazed ceramic coloured tiles 450mm x 350mm x 7mm/350mm x 250mm x7mm thick as in vertical surfaces such as skirting dado etc set and jointed in neat cement slurry, pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 to receive tiles, complete all as specified and directed.

M&L for chequered cement concrete tiles 30 cm x30 cm x 25mm th with grey cement and pigment, set, jointed and pointed in neat cement slurry in floors laid over 15 mm thick screeed bed in cement mortar 1:6 all as spd & direted.

25mm thick PCC 1:2:4, type B-0 (using 12.5 mm graded crused stone aggregate) as in floors to recieve floor finishes, complete all as specified.

75 mm thick PCC 1:3:6, type C2 (using 40 mm graded aggregate ) as in sub base for receiving floor finishes etc complete all as specified.

Factory made solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification & drawing shown in SSR Part-II, complete all as specified and directed.

Factory made solid panel PVC door shutter 30mm thick (stile) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rails and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to in stiles & rails with suitable PVC sheet beading and joinned together with solvent cement supplying & fixing in frames at site as per specification and drawing shown in SSR Part -II, complete all as specified and directed.

M&L for 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed at site, complete all as specified and directed.

S&F 35mm thick 2nd class hard wood plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged) or of veneered particle board medium density, wood particle board with commercial face veneers supplied and fitted to chowkats at site, complete all as specified and directed.

S&F 35mm thick 2nd class kail hard wood glazed & skeleton shutters for door, open rebated and prepared to receive glass, gauge etc. (internal sash bars) edges of framing plain, chamfered or rounded, fitted with cuts and mitred beads for securing glass etc. sizes of members of shuttered as specified in SSR Part- I Section-8 Clause 8.20 (a), complete all as specified and directed.

S&F 30mm thick 2nd class kail hard wood glazed & skeleton shutters for windows/ ventilators open rebated and prepared to receive glass gauge etc, edges of framing plain, chamfered or rounded , fitted with cuts and mitred beads for securing glass etc. sizes of members of shuttered as specified in SSR Part- I Section-8 Clause 8.24 (b), complete all as specified and directed.

S&F 9mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on both faces, fixed with screws to timber frame work on wall & ceiling, complete all as specified and directed.

S&F anodised aluminium snap grid of size 605mm x 605mm frame work for false ceiling including straining with GI wire 4 mm dia, complete all as specified and directed.

S&F 10mm thick PVC insulation panels with EPS stuck to 1mm thick plain PVC sheet, suitably placed in false celing grid made of aluminium GI/MS, complete all as specified and directed.

S&F solid PVC wall lining consisting of 5mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC/ wooden frame, complete all as specified and directed.

S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make frame, complete all as specified and directed.

M&L for 2nd class soft wood, plain fillets, square, rectangular or triangular in section, secured with nails or brads, sectional area exc 6.0 Sqcement mortar but not exc 13 Sqcement mortar, bull nosed splayed chamfered or rounded on edge or face, complete all as specified and directed.

S&F 40mm thick, 2nd class hardwood planks, planed one side with butt joints and fixed with nails in any position, complete all as specified and directed.

S&F weather boarding of 2nd class hardwood, clean sawn, plain, 20mm thick or feather edges, fixed with 30mm lap joints, complete all as specified and directed.

M&L for 2nd class hard wood, clean sawn, fixed as in scantling, roof perlins, rafters, ridges etc, complete all as specified and directed.

S&F 0.63mm thick galvanised, corrugated mild steel sheeting with two corrugation side lap, fixed with 'L' or 'J' type screws and washers, as in roofs, walls etc. with grade of zinc coating 275 gram/ Sqm, complete all as specified and directed.

S&F 0.63mm thick plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 gram/ Sqm, complete all as specified and directed.

S&F for Hand rails, half round or other stock section , nosing to steps in cluding embeding in concrete and screwing etc. wind ties for roof including securing bolts and similar work conforming to Fe 290 gde E 165 complete all as specified and directed.

M&L for mild steel framed work such as grills, gratings etc, with ends of bars shouldered and or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work, confirming to Fe-290 Gde E-165, complete all as specified and directed.

S&F 300mm long mild steel sliding door bolt, plate type, stove enamelled black with bright bolt not less than 12mm dia with and including a minimum of 6 Nos bolts and nuts, four on bolt plate and two on staple plate, complete all as specified and directed.

S&F 200mm long barrel tower bolt, stove enamelled black with bright bolt, complete all as specified and directed.

All as per item No 22 here-in-before but 150mm.

S&F 150mm long mild steel pressed handle, oval type, stove enamelled black, complete all as specified and directed.

S&F butt hinges, medium weight, cold rolled mild steel, size 100mm, complete all as specified and directed.

All as per item No 25 here-in-before but 75mm

S&F ordinary rat tail rod pattern springs, brass 300mm size, including roller and roller plate, complete all as specified and directed.

S&F in repair floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, of size 150mm, complete all as specified and directed.

S&F 4.0mm thick sheet glass, ordinary quality and glazing with oil putty or wooden beads/ glazing pins in square not exc 0.50 Sqm in each pane, including hacking out old broken/ damaged glass in any position, complete all as specified and directed.

S&F 4.0mm thick sheet glass, ordinary quality and glazing with oil putty or wooden beads/ glazing pins in square not exc 0.50 Sqm in each pane, complete all as specified and directed.

M&L 4mm thick figured glass pin headed type and glazing with oil putty or fixed with beads/ glazing pins in square not exc 0.50 Sqm in each pane including hacking out old broken/ damaged glass in any position, complete all as specified and directed.

S&F galvanised steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm, fixed with tinned tacks or galvanised wire staples, complete all as specified and directed.

S&F in repair galvanised steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm, fixed with tinned tacks or galvanised wire staples, complete all as specified and directed.

Steel water tubing, 15mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specified and directed.

Steel water tubing, 20mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specified and directed.

Rotational moulded polythylene 500 litres capacity water storage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position including 20mm brass ball valve high pressure with brass rod & high density plastic ball, complete all as specified and directed.

S&F in repairs vitreous china squatting pan water closet, orissa pattern, size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe), jointing to flush pipe complete and making good to floor in cement concrete M-5 (1:5:10), type E-2 using 40mm graded crushed stone aggregate, complete all as specified and directed.

S&F in repair vitreous china wash down water closet pan (pedestal pattern), coloured (excluding fixing bolts, flushing cistern & flush pipe) & including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc. and including 'P' or 'S' trap and plastic water closet seat black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinges device & making good to dismantled/ damaged floor in cement mortar M-15 (1:2:4) type B-1 (using 20mm graded crushed stone aggregated), complete all as specified and directed.

S&F in repair vitreous china urinals, bowl type 465x355x265 mm white, with grating and union for discharge pipe & fixing plugs, bedding urinal against wall in cement mortar 1:2, complete all as specified and directed.

S&F in repair vitreous china, wash hand basin, flat back of size 550mmx400mm with brackets including cutting for and pinning in ends of brackets, including 32mm dia PVC waste pipe, waste coupling and 15mm bore pillar tap,fancy type, cast copper alloy, with capstan head, chromium plated screwed down high pressure, with or without lettered hot/cold with long screwed shanks and fly nuts screwed for iron pipe, complete all as specified and directed.

S&F in repair 10 litre capacity PVC valveless, low level, synphonic action type, flushing cistern, with inlet, ball valve, float valve, handle including brackets, complete all as specified and directed.

S&F in repair grating doom 125 mm dia with waste hole of PTMT, complete all as specified and directed.

S&F in repair PVC connection 15mm size with PTMT nuts of length 600mm, complete all as specified and directed.

S&F in repairs swivel shower of PTMT any colour with arm, 195 mm long with bend of 45 degree with flange (both min wt 80 gms ), complete all as specified and directed.

S&F in repairs 110mm PVC (SWR) WC connector bent type, complete all as specified and directed.

S&F in repairs 75mm dia cast iron nahani trap including jointing to pipe, complete all as specified and directed.

S&F in repairs 15mm bore bib tap, fancy type, chromium plated, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule, complete all as specified and directed.

S&F & repairs, 15 mm bore CP stop valve cost copper alloy screwed down , high pressure with crutch or butterfly handle fency type complete.

S&F in repairs 15mm bore stop valves, fancy type, chromium plated with long long shank and cup (concealed type), cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union, complete all as specified and directed.

S&F in repair 15mm bore pillar tap, cast copper alloy, with capstan head, chromium plated screwed down high pressure, with or without lettered hot/cold with long screwed shanks and fly nuts screwed for iron pipe, complete all as specified and directed.

S&F in repair 20mm bore gun metal globe or gate valve with iron wheel head screwed head both for iron pipe & fixed, complete all as specified and directed.

S&F in repairs brass chromium plated tubular towel rail with brackets, 20mm dia, D type, 60 cement mortar long between flanges.

S&F in repair 15 mm bore brass CP mixer for mixing hot and cold water screwed down for iron pipe and fixeds, complete all as specified and directed.

S&F in repair 15mm bore bib taps of standard PTMT any colour high pressure screwed for iron pipe and fixed (minimum weight 90gms), complete all as specified and directed.

S&F in repair 20mm ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 210gms), complete all as specified and directed.

75mm bore dia PVC (SWR) pipes, single socketed, in any length with rubber ring joints fixed to walls, complete all as specified and directed.

110mm bore dia PVC (SWR) pipes, single socketed, in any length with rubber ring joints fixed to walls, complete all as specified and directed.

110mm bore dia PVC (SWR) bends, complete all as specified and directed.

75mm bore dia PVC (SWR) bends, complete all as specified and directed.

110mm PVC (SWR) vent cowl complete all as specified and directed.

75mm PVC (SWR) vent cowl complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of wall and applying two coats of cement base paint over a coat of alkali-resistant priming coat, complete all as specified and directed.

Preparation of new plastered surfaces of wall by applying 3mm thick wall care putty and applying two coats of oil bound distemper over a coat of primer, complete all as specified and directed.

M&L for preparation of new wooden surfaces or articles of any description over 10cement mortar width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

M&L preparation of new steel or iron surfaces of any description over 10cement mortar width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified and directed.

M &L for preparing plastered new surface of walls and applying three coats of white wash on walls,complete all as specified and directed.

M &L for preparing old plastered surface of walls and applying two coat of white wash on wall complete all as specified and directed.

S&F in repairs plain mild steel wire, 4.0 mm dia galvanised class 3 in detached work such as mosquito nets and fixing incl straining bolts, hooks, eyes etc.

S&F in repair/replacement of MCB distribution board , 240 volts single pole and neutral , double door, sheet steel, enclosure powder coated with 200 Amps rated copper busbar with neutral link, 4 ways, IP-43 protection, fixed on wall duly grouted in solid block wall or on wooden board with electrical connection and making good disturbed surfaces of walls etc, including two coats of white/colour washing/ distempering etc to match the existing surface, complete all as specified and directed.

S&F in repair/replacement of MCB distribution board , 240 volts single pole and neutral, double door, sheet steel, enclosure powder coated with 200 Amps rated copper busbar with neutral link, 8 ways, IP-43 protection, fixed on wall duly grouted in solid block wall or on wooden board with electrical connection and making good disturbed surfaces of walls etc, including two coats of white/colour washing/ distempering etc to match the existing surface, complete all as specified and directed.

S&F in repair/replacement of MCB distribution board , 240 volts single pole and neutral, double door, sheet steel, enclosure powder coated with 200 Amps rated copper busbar with neutral link, 12 ways, IP-43 protection, fixed on wall duly grouted in solid block wall or on wooden board with electrical connection and making good disturbed surfaces of walls etc, including two coats of white/colour washing/distempering etc to match the existing surface, complete all as specified and directed.

S&F in repair/replacement of MCB distribution board , 415 volts TPN, double door, sheet steel, enclosure powder coated with 200 Amps rated copper busbar with neutral link, 6 ways, IP-43 protection, fixed on wall duly grouted in solid block wall or on wooden board with electrical connection and making good disturbed surfaces of walls etc, including two coats of white/colour washing/distempering etc to match the existing surface, complete all as specified and directed.

S&F in repair/replacement of MCB distribution board , 415 volts TPN, double door, sheet steel, enclosure powder coated with 200 Amps rated copper busbar with neutral link, 4 ways, IP-43 protection, fixed on wall duly grouted in solid block wall or on wooden board with electrical connection and making good disturbed surfaces of walls etc, including two coats of white/colour washing/distempering etc to match the existing surface, complete all as specified and directed.

S&F in repair/replacement of MCB, SP, AC 240 volts, "B" series, capacity 06 to 32 Amps, 10kA and making connections, complete all as specified & directed.

S&F in repair/replacement of MCB, SP, AC 240 volts, "B" series, capacity 40 to 63 Amps, 10kA and making connections, complete all as specified & directed.

S&F in repair/replacement of MCB, SPN, AC 240 volts, "B" series, capacity 32 Amps, 10kA and making connections, complete all as specified & directed.

S&F in repair/replacement of MCB, SPN, AC 240 volts, "B" series, capacity 40-63 Amps, 10kA and making connections, complete all as specified & directed.

S&F in repair/replacement of MCB TPN 415 volts, 40-100 Amps "B" series, 10 kA capacity, complete all as specified and directed.

S&F in repair/replacement of MCCB 4 pole, 415 volts adjustable type, 160 Amps with breaking capacity 36 KA complete all as specified as directed.

S&F in repair/replacement of MCCB 4 pole, 415 volts adjustable type, 200 Amps with breaking capacity 36 KA complete all as specified as directed.

S&F in repair/replacement of automatic source changeover with current limiter 30/20A single phase ACCL, complete all as specified as directed. Make : Havells Cat Part No DHABOSN3020 or its equivalent from the makes given in Appx 'A' to particular specifications.

S&F in repair/replacement of change over switch, off load, 415 volts, FP including sheet metal enclosure of capacity 63 Amps, complete all as specified and directed. Make : Indoasian Cat Part No OFFP0063 or its equivalent from the makes given in Appx 'A' to particular specifications.

S&F in repair/replacement of change over switch, off load, 415 volts, FP including sheet metal enclosure of capacity 32 Amps, complete all as specified and directed. Make : Indoasian Cat Part No OFFP0032 or its equivalent from the makes given in Appx 'A' to particular specifications.

S&F in repair/replacement of single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps, 240 volts, complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including unscrewing from board fitting and fixture such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody for reuse if serviceable or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

Point wiring for one light point/fan point/bell point controlled by one switch with 1.5 sqmm PVC FRLS insulated unsheathed copper conductor single core multi strand flexible cable maintaining colour coding (Phase- Red/yellow/Blue, Neutral- Black) and 1.5 sqmm PVC insulated unsheathed copper conductor single core cable (green color) as earth lead in and including PVC casing and capping/Conduit medium grade of suitable size, run on wall/surface with all fittings (ISI Marked) controlled by one switch including CI/MS sunken box of required size with 3 mm thick plastic laminated sheet cover or PVC Gang Box of adequate size for one light point/fan point controlled by one switch and making good disturbed surfaces with cement mortar 1:3 to match with the existing surface, complete all as specified and directed.

All as per srl item No-111 here in above but for one 5 pin 5A socket outlet independent controlled by one switch, complete all as specified and directed.

All as per srl item No-111 here in above but for one 5A socket outlet on the same board controlled by one switch, complete all as specified and directed.

All as per serial item No 111 here-in-before but for 5 pin 15 Amps socket outlet independent board with 2.5 sqmm PVC FRLS insulated unsheathed copper conductor single core multi strand flexible cable and 2.5 Sqmm PVC FRLS insulated unsheathed copper conductor single core cable (green color) as earth lead, complete all as specified and directed.

Switch piano flush button types 6 Amp, single pole, one way complete all as specified and directed.

Socket outlet 2 in 1, 3 pin, 6 Amps flush type 50 Hz, complete all as specified and directed.

Switch piano flush button types 16 Amp, single pole, one way complete all as specified and directed.

Socket outlet 2 in 1, 3 pin, 6 and 16 Amps flush type 50 Hz, complete all as specified and directed.

Ceiling rose, 3 terminal, bakelite 65mm x50mm, surface type, PVC/ Polycarbonate, isolated body, complete all as specified and directed.

Fan regulator electronic, step type hum free suitable to control speed of fan from 0 to 100% and connecting electrically all as required at site or directed.

Lamp holder, PVC/ Polycarbonate type with back plate, straight/ angular suitable for batten fittings, complete all as specified and directed.

Bell push, flush type, 5/6 Amps, complete all as specified and directed.

Bell, AC, 240 Volts, single pole, complete all as specified and directed.

Supply and fixing of LED 7 watt bulb ( White/warm white) complete all as specified and directed by Engr-in-Charge.

S&F in repair/replacement of Rigid non-metallic grade PVC conduit of size 25 mm dia, exclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc, complete all as specified and directed.

S&F in replacement of PVC casing and capping, medium grade, of size 20 mm dia, exclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc complete all as directed.

S&F in repair/replacement of cable PVC FRLS insulated unsheathed with flexible multistranded copper conductor of size 1.50 Sqmm 1100 Volts grade as per site requirement of existing colour coding adopted, complete all as specified & directed.

S&F in repair/replacement of cable PVC FRLS insulated unsheathed with flexible multistranded copper conductor of size 2.50 Sqmm 1100 Volts grade as per site requirement of existing colour coding adopted, complete all as specified & directed.

S&F in repair/replacement of cable PVC FRLS insulated unsheathed with flexible multistranded copper conductor of size 4.0 Sqmm 1100 Volts grade as per site requirement of existing colour coding adopted, complete all as specified & directed.

M&L in repair/replacement of sub main wiring with two single core PVC insulated flexible copper conductor cable of size 4.00 sqmm and one single core PVC insulated flexible copper conductor cable green colour of size 4.00 sqmm as earth lead in & including PVC casing capping medium grade 2mm thickness ISI marked incl taking down old unsv, complete all as required at site or directed.

M&L in repair/replacement of sub main wiring with two single core PVC insulated flexible copper conductor cable of size 6.0 sqmm and one single core PVC insulated flexible copper conductor cable green colour of size 6.0 sqmm as earth lead in & including PVC casing capping medium grade 2mm thickness ISI marked incl taking down old unsv, complete all as required at site or directed.

M&L in repair/replacement of sub main wiring with two single core PVC insulated flexible copper conductor cable of size 2.50 sqmm and one single core PVC insulated flexible copper conductor cable green colour of size 2.50 sqmm as earth lead in & including PVC casing capping medium grade 2mm thickness ISI marked incl taking down old unsv, complete all as required at site or directed.

S&F in repair/replacement of 1100volts grade heavy duty cable PVC insulated aluminium solid conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core 4 sqmm cable flat or circular, complete all as specified and directed.

S&F in repair/replacement of 1100volts grade heavy duty cable PVC insulated aluminium solid conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core 10 sqmm cable flat or circular, complete all as specified and directed.

S&F in repair/replacement of 1100volts grade heavy duty cable PVC insulated aluminium solid conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core 16 sqmm cable flat or circular, complete all as specified and directed.

LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete, complete all as specified and directed.

Surface and wall mounted LED batten 20 Watt ( white/ warm white) with aluminum housing & integrated electronic driver , extruded Aluminium heat sink provided for efficient heat dissipation, LED life time of 30000* hours all as specified and as directed. Make: Havells Cat Part No: LUMILINEPLUSNEOBS20WLED830SPCSSIND or equivalent from the makes given in Appx 'A' to particular specifications.

35/36 watt (Warm shite/white) LED luminaire 600 mm x 600 mm, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cable of suitable size complete including taking out old unsv, complete all as specified and directed.

Round/square shape 15 watt ( white/Warm white) 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed

LED light fitting 1x9W/1X10W bulkhead luminaire including LED light, driver holder and connecting up with three core flexible copper conductor cable of suitable size including taking out old, complete all as specified and directed.

9 Watt decorative wall light fixture made up of polycarbonate with LED lamp, B22 base and connecting electrically to ceiling rose using PVC FRLS insulated and overall sheated flexible copper conductor cable of suitable size complete, complete all as specified and directed. Make Havells Cat Part No LHDL02160099 or equivalent in Crompton Greaves/ GE/Philips/Bajaj.

Taking down the old UNSV Bed lamp fitting and Supply, Installation, testing and commissioning of LED bed side/ Wall light fitting, integrated type, with system wattage not more than 4W, using 3W for LEDs. The lumen output of LED (Light source) shall not be less than 230 lumens. The housing shall be of aluminium and white color coating. The head of the luminaries shall be adjustable type. The beam angle shall be < 50 deg. Lamp lifetime up to: 15,000 hrs. Total lumen output fixture: > 170 lm. Bulb technology: LED, Safety Extra Low Voltage. Mains power: Range 220 V–240 V, 50-60 Hz, IP20, protection against objects bigger than 12.5 mm, no protection against water, earthed properly. The Net weight of item should not exceed 0.3 kg. Make: PHILIPS 56240/31/16 STAR or equivalent from the makes given in Appx 'A' to particular specifications.

25 Watt (WW) LED post top in sphercal shape polycarbonate opal and clear diffuser with IP 65/66 protection, inbuilt electronic driver, power factor >0.9 with THD <10% including connecting electrically to ceiling rose using PVC FRLS insulated and overall sheated flexible copper conductor cable of suitable size, complete all as specified and directed. Make : Bajaj Cat Part No BLPTSP 25W WW LED or equivalent in Crompton Greaves/ GE/Philips/Havells.

M&L in replacment of Earthing complete with galvanised steel earth plate electrode 60 cement mortar x 60cement mortarx6mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 meters below normal ground level, connecting to the GI wire 4 mm dia by means of bolls, nuts, check nuts and washers of galvanised iron and earth wire protected by provision of GI light grade pipe 15mm bore including provision of concrete pit in PCC 1:2:4, type B-1 (using 20mm graded stone aggregates) with 40mm thick cover of RCC 1:2:4, reinforced with XPM weight not less than 4 Kg/Sqm) and frame of angle iron 25x25x6mm with lugs 02 Nos and handle of 6mm dia MS bar made to shape, GI medium grade 20mm bore pipe for watering , perforated at bottom, 1.75 metre long placed on top edge of earth plate. charcoal and common salt filling with fixing arrangement, funnel wire mesh and earth work in soft soil returning filling in and removal of surplus soil to a distance not exceeding 50 meters all as per electrical plate 3 of SSR-2009 Part-I and connecting to earth test point all as specified or indicated including testing on completion. Note :- (i) Item of earthing includes cost of 7.5 m long GI wire of size 4 mm dia with protection pipe of 15mm dia GI medium grade, any variation in length shall be adjusted through deviation order based on SSR rates enhanced by (-) 14.50%. (ii) On testing after completion of earthing if the desired earth resistance is not obtained earthing will be re-done by the contractor at his own risk and cost.

Painting of ceiling fans complete of any size and make, in situ including filling cavities with filler, by spraying one coat of synthetic enamel paint after cleaning all dust etc, complete all as specified and directed.

Replacement of capacitor 2.5/3.15 mfd AC 230 volts 50 Hz complete all as specified and directed.

Replacement of capacitor 4 mfd AC 230 volts 50 Hz complete all as specified and directed.

Replacement of ball bearing suitable for ceiling fan/exhaust fan any size and any make, complete all as specified and directed.

Replacement of gun metal bush with suitable size for ceiling fan any make, any size and sweep, complete all as specified and directed.

Rewinding of AC ceiling fan/wall mounted fan motor as existing at site, of any make with super enameled copper winding wire as per existing, including cutting of old burnt winding, Sleeve work, varnishing with `B' class insulation varnish, connection with flexible wire of appropriate size two core copper wire up to connector block. Qty of copper winding wire not less than 350 grams and not more than 500 grams per fan motor, complete all as specified and directed.

Rewinding of exhaust fan motor any size, from 225 to 400 mm sweep with supper enameled copper wire of as per sxisting, including necessary cutting of old burnt winding wire, cleaning of slots and provision of necessary threading/sleeve work and taking out connection in lead with PVC copper wire of appropriate size up to connector block, complete all as specified and directed.

Taking down carefully geyser 25/35/50 liters capacity from wall after unscrewing nuts/bolts etc. and refixing the same in position after necessary repair/replacement of spare parts including testing etc complete all as specified and directed. Note: Repleacement of spare parts shall be measured and paid for separately under respective items.

Repleacement of heating element, AC 230 Volt, of rating 1500W (circular/ triangular) ISI mark as per existing any type, complete all as specified and directed.

Replacement of heating element, AC 230 Volt, of rating 2000W (circular/triangular) ISI mark as per existing any type, complete all as specified and directed.

Replacement of thermostat switch, AC 230 Volt, adjustable range from 0-90 degree Celsius, complete all as specified and directed.

Replacement of indicator lamp round/square in shape suitable for 25-50 ltr storage type water heater as per sample 230 volt, complete all as specified and directed.

Replacement of auto-cut switch suitable for geyser 25-50 ltrs, 230 volts AC, all as per sample, complete all as specified and directed.

Replacement of geyser assembly suitable for geyser 25-50 ltrs, 230 volts AC, all as per sample, complete all as specified and directed.

Replacement flexible PVC connection pipe heavy duty suitable for hot water to bear the temperature 100 degree Celsius with out let and inlet connection brass adaptor and PVC washer having size 450 mm long 15 mm nominal dia complete all as specified and directed.

Supply and fixing in repair Plug top 3 pin 15 amps 230 volts including taking old plug top complete all as directed.

S&F in replacement of sunken box cast iron/ pressed steel terminal boxes 60mm deep 6x8 for mounting of switch/socket on hylum sheet and including hylum sheet , screws etc complete all as directed by Engr-in- Charge at site.

S&F in replacement of sunken box cast iron/ pressed steel terminal boxes 60mm deep 8x10 for mounting of switch/socket on hylum sheet and including hylum sheet, screws etc complete all as directed by Engr-in- Charge at site.

S&F in replacement of sunken box cast iron/ pressed steel terminal boxes 60mm deep 10x12 for mounting of switch/socket on hylum sheet and including hylum sheet , screws etc complete all as directed by Engr-in- Charge at site.

S&F in replacement of PVC Gang box surface type suitable for fixing of 5 pin 15 Amp multipurpose switch socket on wall complete all as specified.

S&F in replacement of PVC Gang box surface type suitable for fixing of 5 pin 5 Amp multipurpose switch socket on wall complete all as specified.

M/S SHEIKH FEROOZ AHMAD

M/S Hilal Builders