Major repair Works

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meter lead:

Desmanting of flooring with care including stacking of servceable material and diposal of unserviceable material with in 50mtr. Lead for cement concrete flooring

Polished blue kota stone flooring, jaid over 20mm thick base of C.M. 1:4 and jointed with grey cement slurry to match the shade of the slab including rubbing and polishing complete for area of each slab up to 2001 to 5000 Sq. Cm

Stone Kharanja : Random rubble dry stone kharanja under floor

PCC : Providing and laying in position cement concrete including curing,compaction ect. Complete in specified grade excluding the cost of centering and shuttering-All work up to plinth level. M10 grade Nominal Mix 1:3:6 (1 cement :3 coarse sand :6 graded stone aggregate 20mm nominal size).

Internal plaster: plaster on new surface on walls in cement sand mortar 1:6 including racking of joint ect. Complete fine finished 20mm thick

Internal finishing- Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding: New work (two or more coats ) over and including scrapping and priming coat with cement

P&F rigid PVC Pipe (IS:4985 mark) class II/(4KG./Cm2.) approved quality /mark including joining the pipe with solvent cement rubber ring and lubricant. 110mm dia

Wiring of light point/ fan point / exhaust fan point / call bell point as per PWD specification for electrical works with ISI marked 1.5sq. Mm nominal size FR PVC insulted unsheathed flexible copper conductor 1.1 kV grade (IS:694) and 1.5sq.mm nominal size FR/PVC insulted unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS (IS:9537 P-III) vergin material PVC conduit & Its all accessories (J.B. , Bends etc.) round tiles ,18 SWG Hot Dipped Galvanized Modular Box with earth terminal , 6A Modular switch , Modular face plate with grid plates, 3pin ceiling rose / lamp Holder / 3 pin connector , screws etc, making connections, all as per pre appoverd by Engineer in charge , testing etc. complete as required.For specification of copper conductor , Phenolic Laminated sheets & Electrical / Wiring accessories refer chapter E-04, E-05 & E-07. For additional technical parameter of product/work , refer Annexure "A" attached with this BSR. Long Point (up to 10mtr)

Wiring of 3/5 pin 6 amp. Light plug point as per PWD specification for electrical works with ISI marked 1.5 sq. mm nominal size FR/PVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS:694) and 1.5 sq. mm nominal size FR/PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS (IS:9537 P-III) vergin material PVC conduit & Its all accessories (J.B. , Bends etc.)round tiles ,18 SWG G.I. box with earth terminal of required size, 6A switch ,3/5 pin 6 A socket , 3.0 mm thick ISI marked Phenolic Laminated sheets(IS :2036-1995) , AI. alloy /cadmium plated iron screws 20mm cup washers etc. all as per pre approved by Engineer in charge, making connections, testing etc.complete as required.For specification of copper conductor , Phenolic Laminated sheets & Electrical / Wiring accessories refer chapter E-04, E-05 & E-07. For additional technical parameter of product/work , refer Annexure "A" attached with this BSR. On board

S&F following sizes (dia) of ISI marked MMS (IS:9537 P-III) vergin material PVC conduit as per PWD specification for electrical works along with its accessories (IS:3419) as required in recess including cutting the wall , covering conduit and making good the same as required. All relative and latest acceptance tests reports by any NABL accredited lab for the conduit shall be submitted before execution & Engineer in charge. For additional technical parameter of product/work , refer Annexure "A" attached with this BSR.MMS (9537 P-111) PVC conduct. 25mm.

Supplying & Drawing FR PVC insulted unsheathed flexible copper conductor as per PWD specification for electrical works with ISI marked (IS:694) and as per IS 8130:2013 of 1.1 kV grade .Wire should be made from 99.99% purity copper , class 5 stranding in acc . to IEC 60228 for lower watt loss , oxygen free (<10ppm) for less chances of oxidization and higher silver contant for gives better conductivity ,insulation PVC type A , flame retardant as per IS 10810-53 , better amperage rating as per VDE 0298 part 4, in exiting surface or reccessed PVC/MS conduit /casing capping including all as per pre approved by Engineer in charge, making connections etc.as required .OEM must have its own in house NABL lab setup for all testing facilities for wire .For additional technical parameter of product/work , refer Annexure "A" attached with this BSR. 2x1.5sqmm.

Supplying & Drawing FR PVC insulted unsheathed flexible copper conductor as per PWD specification for electrical works with ISI marked (IS:694) and as per IS 8130:2013 of 1.1 kV grade .Wire should be made from 99.99% purity copper , class 5 stranding in acc . to IEC 60228 for lower watt loss , oxygen free (<10ppm) for less chances of oxidization and higher silver contant for gives better conductivity ,insulation PVC type A , flame retardant as per IS 10810-53 , better amperage rating as per VDE 0298 part 4, in exiting surface or reccessed PVC/MS conduit /casing capping including all as per pre approved by Engineer in charge, making connections etc.as required .OEM must have its own in house NABL lab setup for all testing facilities for wire .For additional technical parameter of product/work , refer Annexure "A" attached with this BSR. 2x2.5sqmm.

Providing & Fixing of IP20 SMD Mid Power LED batten type integrated light fixture made from polycarbonate /extruded aluminium powder coated housing with in built driver, Power Consumption of 18W/20W, system lumen efficacy ≥ 120 Im/Watt output, internal surge protection of 2.5 KV with Short & Open circuit protection, THD < 10% ,p.f.20.95, CRI >80, life time of minimum 50000 Burning Hours with, 70% of intial Lumen maintaned till life ends, CCT 3000°K/4000°K / 5700°K/6000°K/6500°K (As per ANSI Bin), maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate (T.C.). Manufactures Word Mark/ Name Engraved/Embossing/ Screen printing on housing. 1170mm(+/-10%) LED batten with min. lumen output 2200 Im

Providing & Fixing of BEE Star rated copper wounded double ball bearing capacitor start, aluminium body & Metallic blade ceiling fan Conforming to all the performance requirements laid down in IS 374:2019 including all amendments, as applicable; & Carry BIS licensing (i.e. ISI marking) with down rod up to 80 cm with secondary support safety cable (steel rope), cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/work, refer Annexure "A" attached with this BSR. 1200mm sweep BEE 2 star rated (Service value >=4.5 to <5)

P & F 1.2mm thick M.S. Recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mm length extended on each side. All as per pre approved by Engineer in charge. For additional technical parameters of product 6.0/work refer Annexure 'A' attached with this BSR

Providing & Fixing of modular type 120 W Step Fan regulator duly ISI marked (IS 11037:1984) with CM/L no. printed made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with IP-20 rating, including all as per pre approved by Engineer in charge, making connections, testing etc. as required. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR5 5 step fan regulator 2 Module 360 dgree rotating